Symbol AP-8132 Installation Manual

AP-8132 Access Point

INSTALLATION GUIDE

2 AP-8132 Access Point

Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered
trademark of Symbol Technologies, Inc., a Zebra Technologies company.

© 2015 Symbol Technologies, Inc.

Installation Guide 3

1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.1 Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.2 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.3 Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.4 AP-8132 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.0 Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.1 Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.2 Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.3 Access Point Placement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.4 Power Injector System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.5 Wall Mount Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.6 Suspended Ceiling T-Bar Mount Installation. . . . . . . . . . . . . . . . . . . . . . . 12

2.7 Suspended Ceiling Tile (Plenum) Installation . . . . . . . . . . . . . . . . . . . . . . 14

2.8 AP-8132 Antenna Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2.9 LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3.0 Basic Access Point Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

4.0 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

4.1 Electrical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

4.2 Physical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

4.3 Radio Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

5.0 Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

6.0 Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

7.0 End-User License Agreement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

8.0 AP-8132 Access Point China ROHS Compliance . . . . . . . . . . . . . . . 52

4 AP-8132 Access Point

!

1 Introduction

The AP-8132 is a plenum rated, 3x3:3 802.11n access point utilizing two 802.11abgn radios.

An AP-8132 model access point uses WiNG 5 software as its onboard operating system. The access point’s unique
WiNG 5 software enables the access point to function as either a Virtual Controller AP capable of adopting and
managing up to 24 additional AP-8132 access points, a Standalone access point or a Dependent mode access
point managed by its connected controller.

If new to access point technology, refer to the WiNG Access Point System Reference Guide to familiarize yourself
with the feature set supported by the WiNG operating system. The guide is available, at www.zebra.com/support

This document is written for the qualified network device installer.

1.1 Document Conventions

The following graphical alerts are used in this document to indicate notable situations:

NOTE Tips, hints, or special requirements that you should take note of.

.

CAUTION Care is required. Disregarding a caution can result in data loss or

WARNING! Indicates a condition or procedure that could result in personal injury or

equipment malfunction.

equipment damage.

Installation Guide 5

1.2 Warnings

• Read all installation instructions and site survey reports, and verify correct equipment installation before
connecting the AP-8132 model access point.

• Remove jewelry and watches before installing this equipment.

• Verify any device connected to this unit is properly wired and grounded.

• Verify there is adequate ventilation around the device, and that ambient temperatures meet equipment
operation specifications.

1.3 Site Preparation

• Consult your site survey and network analysis reports to determine specific equipment placement, power
drops, and so on.

• Assign installation responsibility to the appropriate personnel.

• Identify and document where all installed components are located.

• Ensure adequate, dust-free ventilation to all installed equipment.

• Identify and prepare Ethernet and console port connections.

• Verify cable lengths are within the maximum allowable distances for optimal signal transmission.

1.4 AP-8132 Package Contents

An AP-8132 access point is available in external antenna models only. An AP-8132 ships with the following:

• AP-8132 access point

• AP-8132 Installation Guide (This Guide)

• Wall mount screw and anchor kit

• Accessories bag (LED light pipe for above the ceiling installations)

NOTE An AP-8132 access point can ship with a separately ordered protective

cover (facade) containing a 6-element MIMO antenna (Part No.
ML-2452-PTA6M6-1). When attached, LEDs continue to illuminate
through the cover (similar to the illustration on the next page). A version
of the facade is also available without the MIMO antenna. This cover
(Part No. 21-8132FAC-01) functions strictly as a protective cover for the
access point and provides no operational functionality.

6 AP-8132 Access Point

1.4.1 Features

An AP-8132 access point minimally supports the following feature set:

• 3 RJ-45 connectors (GE1/POE, GE2 and Console)

• LED indicators

• Slots for wall mounting

• Lock port for Kensington® style security lock

• Two custom dual band radios

• Features for snap-on module support through the access point’s USB interface

• 3x3 MIMO, 3 spatial streams

The AP-8132 access point has two RJ-45 connectors supporting 10/100/1000 Ethernet. GE1/POE accepts 802.3at
or 802.3af compliant power from an external source

NOTE When operating in a Gigabit Ethernet environment, CAT-5e or CAT-6 cable

is recommended for Gigabit operation.

Installation Guide 7

2 Hardware Installation

2.1 Installation Instructions

An AP-8132 access point mounts either on a wall (with M4 x 25 pan head screws and wall anchor - or equivalent)
or on a suspended ceiling T-bar.

Once the AP-8132 is installed with facade and cabled, the cables (Ethernet and module connections) should not be
visible when looking directly at the unit (ceiling and wall mounts).

To prepare for the installation:

1. Match the model number on the purchase order with the model numbers in the packing list and on the
case of the access point.

2. Verify the contents of the box include the intended AP-8132 access point, and the included hardware
matches the package contents on page 4.

Part Number Description

AP-8132-66040-US 802.11n 3x3:3 access point dual radio US version

AP-8132-66040-WR 802.11n 3x3:3 access point dual radio non-US (rest of world) version

AP-8132-66040-EU 802.11n 3x3:3 access point dual radio European version

3. Review site survey and network analysis reports to determine the location and mounting position for the
AP-8132 access point.

4. Connect a CAT-5 or better Ethernet cable to a compatible 802.3at or 802.3af power source and run the
cable to the installation site. Ensure there is sufficient slack on the cable to perform the installation
steps.

When operating in a Gigabit Ethernet environment, CAT-5e or CAT-6 cable

NOTE

is recommended for Gigabit operation.

2.2 Precautions

Before installing an AP-8132 model Access Point, verify the following:

• Your using the correctly rated power solution for the AP-8132 (either the AP-PSBIAS-2P3-ATR power
injector or the PWRS-14000-247R external power supply)

• Do not to install the AP-8132 in wet or dusty areas.

• Verify the environment has a continuous temperature range between 0° C to 50° C.

2.3 Access Point Placement

For optimal performance, install the access point away from transformers, heavy-duty motors, fluorescent lights,
microwave ovens, refrigerators and other industrial equipment. Signal loss can occur when metal, concrete, walls

8 AP-8132 Access Point

!

!

or floors block transmission. Install the access point in an open area or add access points as needed to improve
coverage.

Antenna coverage is analogous to lighting. Users might find an area lit from far away to be not bright enough. An
area lit sharply might minimize coverage and create dark areas. Uniform antenna placement in an area (like even
placement of a light bulb) provides even, efficient coverage.

Place the access point using the following guidelines:

• Install the access point at an ideal height of 10 feet from the ground.

• Orient the access point antennas vertically for best reception (applies to external antenna models only).

To maximize the access point’s radio coverage area, conduct a site survey to define and document radio
interference obstacles before installing the access point.

2.4 Power Injector System

An AP-8132 model access point can receive power via an Ethernet cable connected to the GE1/POE (LAN) port.

When users purchase a WLAN solution, they often need to place access points in obscure locations. In the past, a
dedicated power source was required for each access point in addition to the Ethernet infrastructure. This often
required an electrical contractor to install power drops at each access point location. The Power Injector merges
power and Ethernet into one cable, reducing the burden of installation and allowing optimal access point
placement in respect to the intended coverage area.

CAUTION Using a non-compliant injector, or an injector supporting legacy modes

CAUTION Do not plug in the AP-PSBIAS-2P3-ATR Power Injector into the access

The AP-8132’s supported Power Injector (Part No. AP-PSBIAS-2P3-ATR) is a high power POE Injector delivering up
to 30 watts. The access point can only use a Power Injector when connecting the unit to the access point’s GE1/POE
port. The Power Injector is separately ordered and not shipped with an existing AP SKU.

The access point Power Supply (Part No. PWRS-14000-247R) is not included with the access point and is orderable
separately as an accessory. If the access point is provided both POE power and PWRS-14000-247R power
concurrently, the access point will source power from the PWRS-14000-247R supply only. Disconnecting AC power
from the PWRS-14000-247R, causes the access point to re-boot before sourcing power from the POE power
injector. If the AP is operating using injector supplied power, the AP will not automatically reboot if an AC adapter
is connected. The access point continues to operate with power supplied from the AC adapter without change to
the access point operating configuration. If using AC adapter supplied power and a change to the AP’s operating
configuration is warranted, the access point needs to be manually rebooted by the customer.

will not allow the AP-8132 to function at optimum performance levels.

point’s Console port. Connecting the Power Injector into the console
port can damage the port and void the AP-8132’s product warranty.

Installation Guide 9

!

CAUTION The access point supports any standards-based compliant power

A separate Power Injector is required for each AP-8132 access point comprising the network.

source. However, using the wrong solution (including a POE system
used on a legacy access point) could either limit functionality or
severely damage the access point and void the product warranty.

The Power Injector can be installed free standing, on an even horizontal surface or wall mounted using the power
injector’s wall mounting key holes. The following guidelines should be adhered to before cabling the Power Injector
to an Ethernet source and an access point:

• Do not block or cover airflow to the Power Injector.

• Keep the Power Injector away from excessive heat, humidity, vibration and dust.

• The Power Injector isn’t a repeater, and does not amplify the Ethernet signal. For optimal performance,
ensure the Power Injector is placed as close as possible to the data port.

10 AP-8132 Access Point

!

!

!

CAUTION To avoid problematic performance and restarts, disable POE from a

To install the Power Injector to an Ethernet data source and an access point:

CAUTION Ensure AC power is supplied to the Power Injector using an AC cable

1. Connect the Power Injector to an AC outlet (110VAC to 220VAC).

2. Connect an RJ-45 Ethernet cable between the network data supply (host) and the Power Injector Data In
connector.

3. Connect an RJ-45 Ethernet cable between the Power Injector Data & Power Out connector and the
access point’s GE1/POE port.

CAUTION Cabling a Power Injector to the WAN port (GE2 port) renders the AP

Ensure the cable length from the Ethernet source (host) to the Power Injector and access point does not
exceed 100 meters (333 ft).

The Power Injector has no On/Off power switch. The Injector receives power and is ready for device
connection and operation as soon as AC power is applied. Refer to the Installation Guide shipped with the
Power Injector for a description of the device’s LEDs.

wired switch port connected to an access point if mid-span power
sourcing equipment (PSE) is used between the two, regardless of the
manufacturer of the switch.

with an appropriate ground connection approved for the country of
operation.

non-operational. Only use a AP-PSBIAS-2P3-ATR Power Injector with
the access point’s GE1/POE (LAN) port.

2.5 Wall Mount Instructions

A wall mount deployment requires hanging the AP-8132 access point along its width or length using two of three
slots on the bottom of the unit. The AP-8132 can be mounted on to any plaster, wood or cement wall surface using
the provided wall anchors.

The hardware required to install the AP-8132 on a wall consists of:

• Two wide-shoulder Phillips pan head self-tapping screws (M3.5 x 0.6 x 23 mm)

• Two wall anchors

• Security cable (optional)

Optional customer provided installation tools include:

• Security cable

• Philips head screw driver, or drill and drill bit

Installation Guide 11

2.5.1 Wall Mount Procedure - New Installation

This section describes a new AP-8132 installation with no previous access point existing on the intended wall
surface.

1. Place the access point against the wall, ensuring the access point’s logo is in the correct orientation.

2. Mark the screw hole locations 152mm (6 in.) apart on the access point’s long axis or 40mm (1.57 in.) apart
on the access point’s short axis, depending on the intended deployment orientation of the unit.

3. At each point, drill a hole in the wall and insert the anchor.

NOTE When pre-drilling a hole the recommended hole size is 4mm (0.16in.).

4. Place the access point on the anchor. Insert screws through into the anchor.

5. If required, install and attach a Kensington security cable (customer supplied) to the unit’s lock port.

6. Cable the access point using either the Power Injector solution (AP-PSBIAS-2P3-ATR) or the approved
AP-8132 power supply (PWRS-14000-247R).

For Power Injector installations:

a. Connect a RJ-45 CAT5e (or CAT6) Ethernet cable between the network data supply (host) and the

Power Injector Data In connector.

b. Connect a RJ-45 CAT5e (or CAT6) Ethernet cable between the Power Injector Data & Power Out

connector and the access point’s GE1/POE port.

c. Ensure the cable length from the Ethernet source (host) to the Power Injector and

access point does not exceed 100 meters (333 ft). The Power Injector has no On/Off power switch.
The Power Injector receives power as soon as AC power is applied.

For standard power adapter (non Power Injector) and line cord installations:

a. Connect a RJ-45 Ethernet cable between the network data supply (host) and the access point’s

GE1/POE or GE2 port.
b. Verify the power adapter is correctly rated according to the country of operation.
c. Connect the power supply line cord to the power adapter.
d. Attach the power adapter cable into the power connector on the access point.
e. Attach the power supply line cord to a power supply.

7. Attach supported 2.4 GHz or 5 GHz antennas to the connectors. For more information on supported
AP-8132 antennas, see

8. Verify the access point is receiving power by observing the LEDs are lit or flashing. For more information
on AP-8132 LED behavior, see

AP-8132 Antenna Options on page 17.

LED Indicators on page 19.

12 AP-8132 Access Point

!

9. The access point is ready to configure.

CAUTION If not using an AP-PSBIAS-2P3-ATR model power injector, ensure only

the AP-8132’s designated power supply (PWRS-14000-247R) is used
to supply power to the access point. Using an incorrectly rated power
supply could damage the access point and void the product warranty.
Do not actually connect to the power source until the cabling portion
of the installation is complete.

2.5.2 Wall Mount Procedure - Existing Access Point Replacement

An existing AP-7131 or AP-7131N Series access point, installed on a wall (plenum installation), can be replaced by
an AP-8132. Simply remove the existing AP-7131 or AP-7131N from its mounting screws, leave the mounting
hardware in place and install the new AP-8132 directly on to the existing mounting hardware. The cabling
procedure for such a replacement is as described in the previous section.

2.6 Suspended Ceiling T-Bar Mount Instructions

Ceiling mount requires holding the AP-8132 up against a T-bar of a suspended ceiling grid and twisting the unit on
to the T-bar. If deploying the AP-8132 on a sculpted ceiling T-Bar, the access point mounting kit (Part No.
KT-135628-01) can optionally be used as well.

1. If required, install and attach a Kensington security cable (customer provided) to the unit’s lock port.

2. Using only the mounting bracket from the mounting kit, rotate and click the mounting bracket into the
mounting slots on the AP-8132.

3. Attach the antennas to their correct connectors. For more information on supported AP-8132 antennas,
see AP-8132 Antenna Options on page 17.

4. Cable the access point using either the Power Injector solution (AP-PSBIAS-2P3-ATR) or the approved
AP-8132 power supply (PWRS-14000-247R).

For Power Injector installations:

a. Connect a RJ-45 CAT5e (or CAT6) Ethernet cable between the network data supply (host) and the

Power Injector Data In connector.

b. Connect a RJ-45 CAT5e (or CAT6) Ethernet cable between the Power Injector Data & Power Out

connector and the access point’s GE1/POE port.

c. Ensure the cable length from the Ethernet source (host) to the Power Injector and

access point does not exceed 100 meters (333 ft). The Power Injector has no On/Off power switch.
The Power Injector receives power as soon as AC power is applied.

For standard power adapter (non Power Injector) and line cord installations:

a. Connect a RJ-45 Ethernet cable between the network data supply (host) and the access point’s

GE1/POE or GE2 port.

b. Verify the power adapter is correctly rated according the country of operation.

Installation Guide 13

!

c. Connect the power supply line cord to the power adapter.
d. Attach the power adapter cable into the power connector on the access point.
e. Attach the power supply line cord to a power supply.

CAUTION If not using an AP-PSBIAS-2P3-ATR model power injector, ensure only

5. Verify the unit has power by observing the LEDs. For more information on AP-8132 LED behavior, see LED

Indicators on page 19

6. Align the bottom of the ceiling T-bar with the back of the access point.

7. Orient the access point chassis by its length and the length of the ceiling T-bar.

8. Rotate the access point chassis 45 degrees clockwise.

9. Push the back of the access point chassis on to the bottom of the ceiling T-bar.

10. Rotate the access point chassis 45 degrees counter-clockwise. The clips click as they fasten to the T-bar.

the AP-8132’s designated power supply (PWRS-14000-247R) is used
to supply power to the access point. Using an incorrectly rated power
supply could damage the access point and void the product warranty.
Do not actually connect to the power source until the cabling portion
of the installation is complete.

.

11. The access point is ready to configure.

14 AP-8132 Access Point

!

!

2.7 Suspended Ceiling Tile (Plenum) Mount Instructions

An above the ceiling installation requires placing the access point above a suspended ceiling and installing the
provided light pipe under the ceiling tile for viewing the rear panel status LEDs of the unit. An above the ceiling
installation enables installations compliant with drop ceilings, suspended ceilings and industry standard tiles from
.625 to .75 inches thick.

The mounting hardware required to install the access point above a ceiling consists of:

• Light pipe

• Badge for light pipe

• Safety wire (strongly recommended)

• Security cable (optional)

NOTE Notes or warnings about suspended ceiling mounts apply to all

installations where the unit is placed on suspended ceiling tile.

CAUTION Do not mount the access point directly to any suspended ceiling tile

To install the access point above a ceiling:

NOTE Remove the access point’s facade and antennas before installing in an

1. If possible, remove the ceiling tile from its frame and place it, finish side down, on a work surface.

2. If required, install a safety wire, between 1.5mm (.06in.) and 2.5mm (.10in.) in diameter, in the ceiling
space.

3. If required, install and attach a security cable to the access point’s lock port.

4. Mark a point on the finished side of the tile where the light pipe is to be located.

5. Create a light pipe path hole in the target position on the ceiling tile.

6. Use a drill to make a hole in the tile the approximate size of the access point LED light pipe.

CAUTION Take care to not damage the finished surface of the ceiling tile when

with a thickness less than 12.7mm (0.5in.) or a suspended ceiling tile
with an unsupported span greater than 660mm (26in.). Its
recommended you fit the access point with a safety wire suitable for
supporting the weight of the device. The safety wire should be a
standard ceiling suspension cable or equivalent steel wire between

1.59mm (.062in.) and 2.5mm (.10in.) in diameter.

above the ceiling orientation. The access point is not certified for an
above the ceiling installation with its accessories installed.

creating the light pipe hole and installing the light pipe.

Installation Guide 15

7. Remove the light pipe’s two rubber stoppers (from the access point) before installing the light pipe.

8. Connect the light pipe to the bottom of the access point. The dual channel light pipe is mated to the access
point by firmly pressing the light pipe into the two round openings that contained the two rubber plugs
removed in the previous step.

9. Fit the light pipe into hole in the tile from its unfinished side.

10. Slide the badge onto the light pipe from the finished side of the ceiling tile.

11. Attach the antennas to their correct connectors. For more information on supported AP-8132 antennas,
see

AP-8132 Antenna Options on page 17.

NOTE Consider attaching safety wire to the access point safety wire tie point or

security cable (if used) to the access point’s lock port.

12. Align the ceiling tile into its former ceiling space.

13. Cable the access point using either the Power Injector solution (AP-PSBIAS-2P3-ATR) or the approved
AP-8132 power supply (PWRS-14000-247R).

For Power Injector installations:

a. Connect a RJ-45 CAT5e (or CAT6) Ethernet cable between the network data supply (host) and the

Power Injector Data In connector.

16 AP-8132 Access Point

!

b. Connect a RJ-45 CAT5e (or CAT6) Ethernet cable between the Power Injector Data & Power Out

connector and the access point’s GE1/POE port.

c. Ensure the cable length from the Ethernet source (host) to the Power Injector and

access point does not exceed 100 meters (333 ft). The Power Injector has no On/Off power switch.
The Power Injector receives power as soon as AC power is applied.

For standard power adapter (non Power Injector) and line cord installations:

a. Connect a RJ-45 Ethernet cable between the network data supply (host) and the access point’s

GE1/POE or GE2 port.
b. Verify the power adapter is correctly rated according the country of operation.
c. Connect the power supply line cord to the power adapter.
d. Attach the power adapter cable into the power connector on the access point.
e. Attach the power supply line cord to a power supply.

CAUTION If not using an AP-PSBIAS-2P3-ATR model power injector, ensure only

14. Verify the behavior of the access point LED light pipe. For more information on AP-8132 LED behavior, see

LED Indicators on page 19.

15. Place the ceiling tile back in its frame and verify it is secure.

16. The access point is ready to configure.

the AP-8132’s designated power supply (PWRS-14000-247R) is used
to supply power to the access point. Using an incorrectly rated power
supply could damage the access point and void the product warranty.
Do not actually connect to the power source until the cabling portion
of the installation is complete.

Installation Guide 17

2.8 AP-8132 Antenna Options

Two antenna suites are available for an AP-8132. One antenna suite supporting the 2.4 GHz band and another
antenna suite supporting the 5 GHz band. Select an antenna model best suited to the intended operational
environment of the AP-8132 access point.

NOTE In compliance with respective local regulatory law, the access point

software provides professional installers the option to configure the
antenna type and antenna gain for approved antennas.

The AP-8132’s supported 2.4 GHz antenna suite includes the following models:

Part Number Antenna Type

ML-2499-5PNL-72-N Panel Antenna

ML-2499-APA2-01 Dipole Antenna

ML-2499-BPNA3-01R Panel Antenna

ML-2499-BYGA2-01R Yagi Antenna

18 AP-8132 Access Point

Part Number Antenna Type

ML-2499-FHPA9-01R Dipole Antenna

ML-2499-HPA3-01R Dipole Antenna

ML-2499-SD3-01R Patch Antenna

ML-2452-APA2-01 Dipole Antenna

ML-2452-PNA5-01R Panel Antenna

ML-2452-PNA7-01R Panel Antenna

ML-2452-HPA5-036 Dipole Antenna

ML-2452-APAG2A1-01 Dipole Antenna

The AP-8132’s supported 5 GHz antenna suite includes the following models:

Part Number Antenna Type

ML-5299-APA1-01R Dipole Antenna

ML-5299-FHPA10-01R Dipole Antenna

ML-5299-HPA1-01R Dipole Antenna

ML-5299-PTA1-01R Patch Antenna

ML-5299-WPNA1-01R Panel Antenna

ML-5299-BYGA15-012 Yagi Antenna

ML-2452-APA2-01 Dipole Antenna

ML-2452-PNA5-01R Panel Antenna

ML-2452-PNA7-01R Panel Antenna

ML-2452-HPA5-036 Dipole Antenna

ML-2452-APAG2A1-01 Dipole Antenna

NOTE

ML-2499-BPNA3-01R and ML-2499-BYGA2-01R are not approved in EU
countries.

The access point also supports a plastic facade (cover), separately ordered, that either contains an antenna
(Part No. ML-2452-PTA6M6-1) or serves as a plastic cover without an antenna (Part No. 21-8132FAC-01)

For up-to-date information on supported antennas and antenna specifications, please refer to the Enterprise
Wireless LAN Antenna Specification Guide available on the Support site.

Installation Guide 19

2.9 LED Indicators

Both Integrated Antenna and External Antenna models have LED activity indicators on the front of the case. With
the External Antenna models mounted above a ceiling, LEDs are at the center of an oval badge on the ceiling.

The LEDs provide a status display indicating error conditions, transmission, and network activity for the 5 GHz

802.11an (amber) radio and the 2.4 GHz 802.11bgn (green) radio.

Task 5 GHz Activity LED (Amber) 2.4 GHz Activity LED (Green)

Unconfigured
Radio

Normal
Operation

On On

• If this radio band is enabled:
Blink at 5 second interval

• If this radio band is disabled:
Off

• If there is activity on this band:
Blink interval at 1 time per second

• If this radio band is enabled:
Blink at 5 second interval

• If this radio band is disabled:
Off

• If there is activity on this band:
Blink interval at 1 time per second

20 AP-8132 Access Point

Task 5 GHz Activity LED (Amber) 2.4 GHz Activity LED (Green)

Firmware
Update

Locate AP
Mode

On Off

LEDs blink in an alternating green, red and
amber pattern using an irregular blink rate.
This LED state in no way resembles normal
operating conditions.

LEDs blink in an alternating green, red and
amber pattern using an irregular blink rate.
This LED state in no way resembles normal
operating conditions

The LEDs on the bottom of the access point are optionally viewed using a single (customer installed) extended light
pipe, adjusted as required to suit above the ceiling installations. The light pipe uses a dual LED to display the same
functionality as the LEDs on the top of the access point.

Installation Guide 21

3 Basic Access Point Configuration

Once the AP-8132 is installed and powered on, complete the following steps to get the access point up and running
and access management functions:

1. The access point’s IP address is optimally provided using DHCP. A zero config IP address can also be
derived if DHCP resources are unavailable. Using zero config, the last two octets in the IP address are the
decimal equivalent of the last two bytes in the access point’s hardcoded MAC address.

For example:

MAC address - 00:C0:23:00:F0:0A
Zero-config IP address - 169.254.240.10

To derive the access point’s IP address using its MAC address:

a. Open the Windows calculator by selecting Start > All Programs > Accessories > Calculator. This menu

path may vary slightly depending on your version of Windows.

b. With the Calculator displayed, select View > Scientific. Select the Hex radio button.

c. Enter a hex byte of the access point’s MAC address. For example, F0.

d. Select the Dec radio button. The calculator converts F0 into 240. Repeat this process for the last

access point MAC address octet.

2. Point the Web browser to the access point’s IP address. The following login screen displays:

3. Enter the default username admin in the Username field.

4. Enter the default password admin123 in the Password field.

22 AP-8132 Access Point

5. Click the Login button to load the management interface.

NOTE When logging in for the first time, you’re prompted to change the

password to enhance device security in subsequent logins.

NOTE If you get disconnected when running the wizard, you can connect again

with the access point’s actual IP address (once obtained) and resume the
wizard.

6. If this is the first time the management interface has been accessed, a dialogue displays to start the
wizard. Select Start Wizard to run the setup wizard.

Installation Guide 23

The first page of the Initial Setup Wizard displays the Navigation Panel and Introduction for the
configuration activities comprising the access point's initial setup

A green checkmark to the left of an item in the Navigation Panel defines the listed task as having its
minimum required configuration parameters set correctly. A red X defines the task as still requiring at
least one parameter be defined correctly.

24 AP-8132 Access Point

The Introduction screen displays a list of the basic configuration activities supported by the Initial Setup
Wizard.

7. Select Save/Commit within each page to save the updates made to that page's configuration. Select
Next to proceed to the next page listed in the Navigation Panel. Select Back to revert to the previous
screen in the Navigation Panel without saving your updates.

NOTE While you can navigate to any page in the navigation panel, you cannot

complete the Initial AP Setup Wizard until each task in the Navigation
Panel has a green checkmark.

8. Select Next. The Initial AP Setup Wizard displays the Access Point Type screen to define the access
point's Standalone versus Virtual Controller AP functionality and the way the access point is adopted to a
controller.

Installation Guide 25

9. Select an Access Point Type from the following options:

• Virtual Controller AP - When more than one access point is deployed, a single access point can

function as a Virtual Controller AP. Up to 24 access points can be connected to, and managed by, a
single Virtual Controller AP of the same AP-8132 model.

• Standalone AP -Select this option to deploy this access point as an autonomous fat access point. A

Standalone AP isn't managed by a Virtual Controller AP, or adopted by a RFS series controller.

NOTE If designating the access point as a Standalone AP, its recommended the

access point’s UI be used exclusively to define its device configuration,
and not the CLI. The CLI provides the ability to define more than one
profile and the UI does not. Consequently, the two interfaces cannot be
used collectively to manage profiles without an administrator
encountering problems.

• Adopted to Controller - Select this option when deploying the access point as a controller managed
(Dependent mode) access point. Selecting this option closes the Initial AP Setup Wizard. An adopted
access point obtains its configuration from a profile stored on its managing controller. Any manual
configuration changes are overwritten by the controller upon reboot.

Select the Automatic controller discovery option to enable the access point to be discovered and
adopted using layer 2 settings. If preferring layer 3 adoption, select the Static Controller Configuration
option, and define the addresses of the preferred controllers. If using the static method, you’ll also need

26 AP-8132 Access Point

to define whether the access point receives an IP address using DHCP or if IP resources are provided
statically.

10. Select Next. The Initial AP Setup Wizard displays the Access Point Mode screen to define the access
point's routing or bridging mode functionality.

Installation Guide 27

11. Select an Access Point Mode from the available options.

• Router Mode - In Router Mode, the access point routes traffic between the local network (LAN) and

the Internet or external network (WAN). Router mode is recommended in a deployment supported by
just a single access point.

• Bridge Mode - In Bridge Mode, the AP depends on an external router for routing LAN and WAN traffic.

Routing is generally used on one device, whereas bridging is typically used in a larger network. Thus,
select Bridge Mode when deploying this access point with numerous peer APs supporting clients on
both the 2.4 and 5GHz radio bands.

28 AP-8132 Access Point

12. Select Next. The Initial AP Setup Wizard displays the LAN Configuration screen to set the access
point's LAN interface configuration.

13. Set the following DHCP and Static IP Address/Subnet information for the LAN interface:

• Use DHCP - Select the checkbox to enable an automatic network address configuration using the

access point’s DHCP server.

• Static IP Address/Subnet - Enter an IP Address and a subnet for the access point's LAN interface. If

Use DHCP is selected, this field is not available. When selecting this option, define the following DHCP
Server and Domain Name Server (DNS) resources, as those fields will become enabled on the bottom
portion of the screen.

• Use on-board DHCP server to assign IP addresses to wireless clients -Select the checkbox to
enable the access point’s DHCP server to provide IP and DNS information to clients on the LAN
interface.

• Range - Enter a starting and ending IP Address range for client assignments on the access point's
LAN interface. Avoid assigning IP addresses from x.x.x.1 - x.x.x.10 and x.x.x.255, as they are often
reserved for standard network services. This is a required parameter.

Installation Guide 29

• Default Gateway - Define a default gateway address for use with the default gateway. This is a
required parameter.

• DNS Forwarding - Select this option to allow a DNS server to translate domain names into IP
addresses. If this option is not selected, a primary and secondary DNS resource must be specified.
DNS forwarding is useful when a request for a domain name is made but the DNS server, responsible
for converting the name into its corresponding IP address, cannot locate the matching IP address.

• Primary DNS - Enter an IP Address for the main Domain Name Server providing DNS services for
the access point's LAN interface.

• Secondary DNS - Enter an IP Address for the backup Domain Name Server providing DNS services
for the access point's LAN interface

14. Select Next. The Initial AP Setup Wizard displays the WAN Configuration screen to set the access
point's WAN interface configuration.

15. Set the following DHCP and Static IP Address/Subnet information for the WAN interface:

• Use DHCP - Select the checkbox to enable an automatic network address configuration using the

access point’s DHCP server.

• Static IP Address/Subnet - Enter an IP Address/Subnet and gateway for the access point's WAN

interface. These are required fields

• The port connected to the WAN - Select the port used as the physical access point connection to the

external network. This ports available differ depending on the access point model deployed. Access

30 AP-8132 Access Point

point models with a single port have this option fixed.

• Enable NAT on the WAN Interface - Select the checkbox to allow traffic to pass between the access

point's WAN and LAN interfaces.

16. Select Next. The Initial AP Setup Wizard displays the Radio Configuration screen to define support for
the 2.4GHz radio band, 5GHz radio band or to set the radio's functionality as a dedicated sensor.

NOTE The ADSP Sensor Support field displays at the bottom of the screen

only if a radio has been dedicated as a sensor.

17. Set the following parameters for the radio:

• Configure as a Date Radio - Select this option to dedicate this radio for WLAN client support in either

the selected 2.4 or 5GHz radio band.

• Radio Frequency Band - Select either the 2.4GHz or 5.0GHz radio band to use with the radio when
selected as a Data Radio. The selected band is used for WLAN client support. Considers selecting
one radio for 2.4GHz and another for 5GHz support when supporting clients in both the 802.11bg
and 802.11n bands.

• Power Level - Use the spinner control to select a 1 - 23 dBm minimum power level to assign to this
radio in selected 2.4 or 5.0 GHz band. 1 dBm is the default setting.

• Channel Mode - Select either Random, Best or Static. Select Random for use with a 802.11an
radio. To comply with Dynamic Frequency Selection (DFS) requirements in the European Union, the

802.11an radio uses a randomly selected channel each time the access point is powered on.
Select Best to enable the access point to scan non-overlapping channels and listen for beacons

Installation Guide 31

from other access points. After the channels are scanned, it will select the channel with the fewest
access points. In the case of multiple access points on the same channel, it will select the channel
with the lowest average power level. When Constantly Monitor is selected, the access point will
continuously scan the network for excessive noise and sources of interference. Select Static to
assign the access point a permanent channel and scan for noise and interference only when
initialized.

• Configure as a Sensor Radio - Select this option to dedicate the radio to sensor support exclusively.
When functioning as a sensor, the radio scans in sensor mode across all channels within the 2.4 and

5.0GHz bands to identify potential threats within the access point managed network. If dedicating a
radio as a sensor resource, a primary and secondary ADSP server must be specified as an ADSP
management resource.

NOTE If configuring the access point as a sensor, the access point will require a

reboot before its sensor functionality is invoked. The reboot can take
place at the completion of the Initial AP Setup Wizard.

• Disable the Radio - Select this option to disable this radio, thus prohibiting it from either providing
WLAN or sensor support. Verify this course action with your network administrator before rendering
the radio offline.

18. Select Next. The Initial AP Setup Wizard displays the Wireless LAN Setting screen to define network
address and security settings for two WLAN configurations available to the access point as part of the
Initial AP Setup Wizard. Once the access point has an initial configuration defined, numerous additional
WLAN configurations can be set.

32 AP-8132 Access Point

19. Set the following parameters for each of the two WLAN configurations available as part of this Initial AP
Setup Wizard:

• SSID - Enter or modify the Services Set Identification (SSID) associated with the WLAN. The WLAN

name is auto-generated using the SSID until changed by the user. The maximum number of characters
is 32. Do not use < > | “ & \ ? , This is a required parameter for each WLAN.

• WLAN Type - Set the data protection scheme used by clients and access points within the WLAN. The

following options are available:

• No Authentication and no Encryption - Select this option to provide no security between the access
point and connected clients on this WLAN.

• Captive Portal Authentication and No Encryption - Select this option to use a Web page (either
internally or externally hosted) to authenticate users before access is granted to the network. If
using this option, define whether a local or external RADIUS authentication resource is used.

• PSK Authentication and WPA2 Encryption - Select the option to implement a pre-shared key that
must be correctly shared between the access point and requesting clients using this WLAN. If using
this option, specify a WPA key in either ASCII (8-63 characters) or HEX (64 characters) format.

• EAP Authentication and WPA2 Encryption - Select this option to authenticate clients within this
WLAN through the exchange and verification of certificates. If using this option, define whether a
local or external RADIUS authentication resource is used.

• WPA Key - If a WPA key is required (PSK Authentication and WPA2 Encryption), enter an alphanumeric
string of 8 to 63 ASCII characters or 64 HEX characters as the primary string both transmitting and
receiving authenticators must share. The alphanumeric string allows character spaces. This
passphrase saves the administrator from entering the 256-bit key each time keys are generated.

Installation Guide 33

• RADIUS Server - If the WLAN type requires a RADIUS server to validate user credentials, designate
whether the access point is using an External RADIUS Server resource or the access point's own
Onboard RADIUS Server. If using an external RADIUS server resource, provide the IP address of the
external server and the shared secret used to authenticate the request.

NOTE If using the access point’s onboard RADIUS server, an additional RADIUS

Server Configuration screen displays within the Navigation Panel on

the left-hand side of the screen. Use this screen to create user accounts
validated when the access point authenticates client connection requests
to the onboard RADIUS server.

20. Select Next. The Initial AP Setup Wizard displays the RADIUS Server Configuration screen if the
access point’s onboard RADIUS server is required to validate user requests. If an onboard RADIUS server
is not required, the Initial AP Setup Wizard displays the Country/Date/Time screen to set device
deployment, administrative contact and system time information.

34 AP-8132 Access Point

21. Refer to the Username, Password, Description and Actions columns to review RADIUS Server user
accounts. Add new accounts or edit the properties of existing accounts as updates are required.

22. Use the Add On-Board RADIUS Server Users field to set the following parameters for a user account:

• Username - If adding a new user account, create a username up to X characters in length. The

username cannot be revised if modifying the user configuration. This is a required parameter.

• Password - Provide (or modify) a password between X - X characters in length entered each time a

requesting client attempts access to the AP managed network using the access point's onboard
RADIUS server. This is a required parameter.

• Confirm Password - Re-enter (or modify) the password as a means of confirming the password. This is

a required parameter.

• Description - Optionally provide a description of the user account as means of further differentiating

it from others.

Installation Guide 35

23. When completed, select Add User to commit a new user, Modify User to commit a modified user or
Reset to clear the screen without updating the configuration. Selecting Reset clears the field of all

entered user account information.

24. Select Next. The Initial AP Setup Wizard displays the Country/Date/Time screen to set device
deployment, administrative contact and system time information. The system time can either be set
manually or be supplied by a dedicated Network Time Protocol (NTP) resource.

25. Refer to the Country and Time Zone field to set the following device deployment information:

• Location - Define the location of the access point. The Location parameter acts as a reminder of where

the AP can be located within the wireless network.

• Contact - Specify the contact information for the administrator. The credentials provided should

accurately reflect the individual responding to service queries.

• Country - Select the Country where the access point is deployed. The access point prompts for the

correct country code on the first login. A warning message also displays stating an incorrect country
setting may result in illegal radio operation. Selecting the correct country is central to legal operation.
Each country has its own regulatory restrictions concerning electromagnetic emissions and the
maximum RF signal strength that can be transmitted. This is a required parameter.

36 AP-8132 Access Point

• Time Zone - Set the time zone where the access point is deployed. This is a required parameter. The

setting should be complimentary with the selected deployment country.

26. If an NTP resource is unavailable, set the System Date and Time (calendar date, time and AM/PM
designation).

27. Optionally enter the IP address of a server used to provide system time to the access point. Once the IP
address is entered, the Network Time Protocol (NTP) functionality is engaged automatically for
synchronization with the NTP resource.

28. Select Next. The Initial AP Setup Wizard displays the Summary and Commit screen to summarize the
screens (pages) and settings updated using the Initial AP Setup Wizard.

There's no user intervention or additional settings required within this screen. Its an additional means of
validating the configuration before its deployed. However, if a screen displays settings not intended as
part of the initial configuration, the screen can be selected from within the Navigation Panel and its
settings modified accordingly.

Installation Guide 37

29. If the configuration displays as intended, select the Save/Commit button to implement these settings to
the access point’s configuration. If additional changes are warranted based on the summary, either select
the target page from the Navigational Panel, or use the Back and Next buttons to scroll to the target
screen.

38 AP-8132 Access Point

4 Specifications

4.1 Electrical Characteristics

An AP-8132 model access point has the following electrical characteristics:

Operating Current &
Voltage

4.2 Physical Characteristics

An AP-8132 model access point has the following physical characteristics:

Dimensions 9 inches x 6.00 inches x 1.75 inches

Housing Metal

Weight (without
facade)

Operating
Temperature

Storage Temperature -40°F to 185°F/-40°C to 85°C

Operating Humidity 5 to 95% Relative Humidity non-condensing

Storage Humidity 85% Relative Humidity non-condensing

Operating Altitude
(max)

Storage Altitude
(max)

Electrostatic
Discharge

48VDC, 0.625A (AUX input voltage)
48VDC, 0.75A (PWRS-14000-247R power supply)

802.3at, 25.5W (AP-PSBIAS-2P3-ATR Power Injector)

22.9 cm x 15.2 cm x 4.4 cm

3.2 lbs / 1.45 kg

32°F to 122°F/0°C to 50°C

8,000 ft @ 28C

30,000 ft @ 12C

+/-15kV Air and +/-8kV Contact @ 50% Relative Humidity

Installation Guide 39

4.3 Radio Characteristics

The AP-8132 model access point has the following radio characteristics:

Data Rates Supported 802.11b: 1,2,5.5,11Mbps

802.11g: 1,2,5.5,11,6,9,12,18,24,36,48, and 54Mbps

802.11a: 6,9,12,18,24,36,48, and 54Mbps

802.11n: MCS 0-23 up to 450Mbps

Wireless Medium Direct Sequence Spread Spectrum (DSSS),

Orthogonal Frequency Division Multiplexing (OFDM)
Spatial multiplexing (MIMO)
Transmit Beamforming

Network Standards 802.11a, 802.11b, 802.11g, 802.3, 802.11n

Transmit Power
Adjustment

1dB increments

40 AP-8132 Access Point

5 Regulatory Information

All Zebra devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required.

Local language translations are available at the following Website: www.zebra.com/support

Any changes or modifications to Zebra equipment, not expressly approved by Zebra could void the user's authority to operate the
equipment.

Zebra devices are professionally installed, the Radio Frequency Output Power will not exceed the maximum allowable limit for the country
of operation.

Antennas: Use only the supplied or an approved replacement antennas. Unauthorized antennas, modifications, or attachments could cause
damage and may violate regulations.

Wireless Device Country Approvals

Regulatory markings, subject to certification, are applied to the device signifying the radio(s) is/are approved for use in the following
countries: United States, Canada, Japan, China, S. Korea, Australia, and Europe 1

Please refer to the Declaration of Conformity (DoC) for details of other country markings. This is available at: www.zebra.com/doc .

Note: For 2.4GHz or 5GHz Products: Europe includes, Austria, Belgium, Bulgaria, Czech Republic, Cyprus, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovak Republic, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.

Operation of the device without regulatory approval is illegal.

Country Selection

Select only the country in which you are using the device. Any other selection will make the operation of this device illegal. The US version
of Access Point will only have US listed in the country selection table. The US version will be sold /used in the US protectorates: American
Samoa, Guam, Puerto Rico, US Virgin Islands.

Frequency of Operation – FCC and IC

You are reminded of the need to observe restrictions on the use of radio devices in fuel depots, chemical plants etc. and areas where the air
contains chemicals or particles (such as grain, dust, or metal powders).

2.4 GHz Only

The available channels for 802.11bg operation in the US are Channels 1 to 11. The range of channels is limited by firmware.

5 GHz Only

The use in the UNII (Unlicensed National Information Infrastructure) band 1 (5150-5250 MHz) is restricted to Indoor Use Only; any other use
will make the operation of this device illegal.

Industry Canada Statement:

Caution: The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-Channel mobile

satellite systems. High power radars are allocated as primary users (meaning they have priority) of 5250-5350 MHz and 5650-5850 MHz and
these radars could cause interference and/or damage to LE-LAN devices.

.

Installation Guide 41

Avertissement: Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour une utilisation à l'intérieur afin de
réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.

Les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la priorité) pour les bands 5250-5350
MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.

Health and Safety Recommendations

Warnings for Use of Wireless Devices

Please observe all warning notices with regard to the usage of wireless devices.

Potetially Hazerdous Atmospheres - Fixed Installations

You are reminded of the need to observe restrictions on the use of radio devices in fuel depots, chemical plants etc. and areas where the air
contains chemicals or particles (such as grain, dust, or metal powders).

Safety in Hospitals

Wireless devices transmit radio frequency energy and may affect medical electrical equipment. When installed adjacent to other
equipment, it is advised to verify that the adjacent equipment is not adversely affected.

Pacemakers

Pacemaker manufacturers recommended that a minimum of 15cm (6 inches) be maintained between a handheld wireless device and a
pacemaker to avoid potential interference with the pacemaker. These recommendations are consistent with independent research and
recommendations by Wireless Technology Research.

Persons with Pacemakers:

• Should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker when turned ON.

• Should not carry the device in a breast pocket.

• Should use the ear furthest from the pacemaker to minimize the potential for interference.

• If you have any reason to suspect that interference is taking place, turn OFF your device.

Other Medical Devices

Please consult your physician or the manufacturer of the medical device, to determine if the operat ion of your wireless product may interfere
with the medical device.

RF Exposure Guidelines

Safety Information

Reducing RF Exposure - Use Properly

Only operate the device in accordance with the instructions supplied.

International

The device complies with internationally recognized standards covering human exposure to electromagnetic fields from radio devices. For
information on “International” human exposure to elet romagnetic fields refer to the Declaration of Conformity (DoC) at: www.

zebra.com/doc.

42 AP-8132 Access Point

EU

Remote and Standalone Antenna Configurations

To comply with EU RF exposure requirements, antennas that are mounted externally at remote locations or operating near users at
stand-alone desktop of similar configurations must operate with a minimum separation distance of 1 meter from all persons. The 5G band
is designed for indoor use.

US and Canada

Co-located statement

To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must not be co-located or operating in
conjunction with any other transmitter/antenna except those already approved in this filling.

Remote and Standalone Antenna Configurations

To comply with FCC RF exposure requirements, Antennas that are mounted externally must be professionally installed at a fixed location and
operate with a minimum distance of 30 cm from all persons.

IC Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncon-trolled environment. This equipment should be
installed and operated with minimum distance 30cm between the radiator & your body.

Déclaration d'exposition aux radiations:

Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement
doit être installé et utilisé avec un minimum de 30 cm de distance entre la source de rayonnement et votre corps.

Power Supply

This device must be powered from a 802.3af or 802.3at compliant power source which has been certified by the appropriate agencies, or by
a LISTED, Type no. PWRS-14000-247R or AP-PSBIAS-2P3-ATR, direct plug-in power supply, marked Class 2 or LPS (IEC60950-1, SELV). Use
of alternative Power Supply will invalidate any approvals given to this unit and may be dangerous.

Radio Frequency Interference Requirements—FCC

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However there is no
guarantee that interference will not occur in a particular i nstallation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help.

Radio Transmitters (Part 15)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Installation Guide 43

The use of 5 GHz WLAN's, for use in the US, have the following restrictions:

• Notched Band 5.60 - 5.65 GHz

Radio Frequency Interference Requirements – Canada

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003
du Canada.

Radio Transmitters

For RLAN Devices:

The use of 5 GHz RLAN’s, for use in Canada, have the following restrictions:

• Restricted Band 5.60 – 5.65 GHz

This device complies with RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement
est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter
tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable.

Label Marking: The Term "IC:" before the radio certification only signifies that Industry Canada technical specifications were met

To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically
radiated power (EIRP) is not more than that permitted for successful communication.

The device could automatically discontinue transmission in case of absence of information to trans-mit, or operational failure. Note that
this is not intended to prohibit transmission of control or signaling information or the use of repetitive codes where required by the
technology.

The maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified for
point-to-point and non point-to-point operation as appropriate.

In compliance with respective local regulatory law, AP software provides professional installers the option to configure the antenna type
and antenna gain for approved antennas.

This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to
operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type
indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly
prohibited for use with this device.

Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son numéro de modèle s'il fait partie du matériel de
catégorie I) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain
admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est
supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.

Refer to section 2.8 of this guide for a listing of the 2.4 and 5 GHz antennas initially approved for use with the AP-8132.

44 AP-8132 Access Point

CE Marking and European Economic Area (EEA)

The use of 2.4GHz RLAN’s, for use through the EEA, have the following restrictions:

• Maximum radiated transmit power of 100 mW EIRP in the frequency range 2.400 -2.4835 GHz.

• Italy requires a user license for outside usage.

Statement of Compliance

Zebra hereby, declares that this device is in compliance with the essential requirements and other relevant provisions of Directive
1999/5/EC. A Declaration of Conformity may be obtained from www.zebra.com/doc.

Japan (VCCI) - Voluntary Control Council for Interference

Class B ITE

Korea Warning Statement for Class B

Other Countries

Australia

Use of 5GHz RLAN’s in Australia is restricted in the following band 5.50 – 5.65GHz.

Brazil

Declarações Regulamentares para AP-8132 - Brasil

Nota: A marca de certificação se aplica ao Transceptor, modelo AP-8132. Este equipamento opera em caráter secundário, isto é, não tem
direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando
em caráter primário. Para maiores informações sobre ANATEL consulte o site: www.anatel.gov.br

Chile

Este equipo cumple con la Resolución No 403 de 2008, de la Subsecretaria de tel ecomunicaciones, relativa a radiaciones electromagnéticas.

Installation Guide 45

China

Mexico

Restrict Frequency Range to: 2.450 – 2.4835 GHz.

S. Korea

Taiwan

在 5.25-5.35 秭赫頻帶內操作之無線資訊傳輸設備，限於室內使用

Thailand

Turkish WEEE Statement of Compliance

EEE Yönetmeliğine Uygundur

46 AP-8132 Access Point

Waste Electrical and Electronic Equipment (WEEE)

English: For EU Customers: All products at the end of their life must be
returned to Zebra for recycling. For information on how to return product,
please go to: www.zebra.com/weee

.
Français: Clients de l'Union Européenne: Tous les produits en fin de cycle
de vie doivent être retournés à Zebra pour recyclage. Pour de plus amples
informations sur le retour de produits, consultez : www.zebra.com/weee

.
Español: Para clientes en la Unión Europea: todos los productos deberán
entregarse a Zebra al final de su ciclo de vida para que sean reciclados. Si
desea más información sobre cómo devolver un producto, visite:

www.zebra.com/weee

.

Bulgarish: За клиенти от ЕС: След края на полезния им живот всички
продукти трябва да се връщат на Zebra за рециклиране. За информация
относно връщането на продукти, моля отид ете на адрес:

www.zebra.com/weee

.
Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende
ihrer Lebensdauer zum Recycling an Zebra zurückgesandt werden.
Informationen zur Rücksendung von Produkten finden Sie unter

www.zebra.com/weee

.
Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del
rispettivo ciclo di vita devono essere restituiti a Zebra al fine di consentirne il
riciclaggio. Per informazioni sulle modalità di restituzione, visitare il seguente
sito Web: www.zebra.com/weee

.
Português: Para clientes da UE: todos os produtos no fim de vida devem
ser devolvidos à Zebra para reciclagem. Para obter informações sobre como
devolver o produto, visite: www.zebra.com/weee
Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van
hun levensduur naar Zebra te worden teruggezonden voor recycling.
Raadpleeg www.zebra.com/weee

voor meer informatie over het terugzenden
van producten.
Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji
nale¿y zwróciæ do firmy Zebra w celu ich utylizacji. Informacje na temat
zwrotu produktów znajduj¹ siê na stronie internetowej www.zebra.com/weee

.

Čeština: Pro zákazníky z EU: Všechny produkty je nutné po skonèení jejich
životnosti vrátit spoleènosti Zebra k recyklaci. Informace o zpùsobu vrácení
produktu najdete na webové stránce: www.zebra.com/weee

.
Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada
taaskasutamise eesmärgil Zebra'ile. Lisainformatsiooni saamiseks toote
tagastamise kohta külastage palun aadressi: www.zebra.com/weee

.
Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Zebra
vállalathoz kell eljuttatni újrahasznosítás céljából. A termék
visszajuttatásának módjával kapcsolatos tudnivalókért látogasson el a

www.zebra.com/weee

weboldalra.

Installation Guide 47

Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd
måste returneras till Zebra för återvinning. Information om hur du returnerar
produkten finns på www.zebra.com/weee

.
Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava
kierrätettäväksi Zebra-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja
tuotteen palauttamisesta on osoitteessa www.zebra.com/weee

.
Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til
recirkulering, når de er udtjent. Læs oplysningerne om returnering af
produkter på: www.zebra.com/weee

.

Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας
ζωή ς τους, πρέπει να επιστρέφονται στην Zebra για ανακύκλωση. Για
περισσότερες πληροφορίες σχετικά με την επιστροφή ενός προϊόντος,
επισκεφθείτε τη διεύθυνση www.zebra.com/weee

στο ∆ιαδίκτυο.

Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aħħar tal-ħajja ta'
l-użu tagħhom, iridu jiġu rritornati għand Zebra għar-riċiklaġġ. Għal aktar
tagħrif dwar kif għandek tirritorna l-prodott, jekk jogħġbok żur:

www.zebra.com/weee

.
Românesc: Pentru clienţii din UE: Toate produsele, la sfârşitul duratei lor de
funcţionare, trebuie returnate la Zebra pentru reciclare. Pentru informaţii
despre returnarea produsului, accesaţi: www.zebra.com/weee

.
Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe
vrniti podjetju Zebra za reciklažo. Za informacije o vračilu izdelka obiščite:

www.zebra.com/weee

.

Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky musia byť po
uplynutí doby ich životnosti vrátené spoločnosti Zebra na recykláciu. Bližšie
informácie o vrátení výrobkov nájdete na: www.zebra.com/weee

.

Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui,
turi būti grąžinti utilizuoti į kompaniją „Zebra“. Daugiau informacijos, kaip
grąžinti gaminį, rasite: www.zebra.com/weee

.
Latviešu: ES klientiem: visi produkti pēc to kalpošanas mūža beigām ir
jānogādā atpakaļ Zebra otrreizējai pārstrādei. Lai iegūtu informāciju par
produktu nogādāšanu Zebra, lūdzu, skatiet: www.zebra.com/weee

.
Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm ürünler geri
dönüştürme için Zebra'ya iade edilmelidir. Ürünlerin nasıl iade edileceği
hakkında bilgi için lütfen şu adresi ziyaret edin: www.zebra.com/weee

.

48 AP-8132 Access Point

6 Support

Part Numbers

Part Number Description

AP-8132-66040-US 802.11n 3x3:3 access point dual radio US version

AP-8132-66040-WR 802.11n 3x3:3 access point dual radio non-US (rest of world) version

AP-8132-66040-EU 802.11n 3x3:3 access point dual radio European version

If you have a problem with your equipment, contact support for your region.

Contact information is available at: www.zebra.com/support

When contacting Support, please provide the following information:

• Serial number of the unit

• Model number or product name

• Software type and version number

Support responds to calls by e-mail, telephone, or fax within the time limits set forth in support agreements. If you
purchased your product from a business partner, contact that business partner for support.

Customer Support Web Sites

Support located at www.zebra.com/support

provides information and online assistance including developer tools, software downloads, product manuals and
online repair requests.

Manuals

www.zebra.com/support

.

Installation Guide 49

7 End-User License Agreement

BY DOWNLOADING, INSTALLING, OR USING THE SOFTWARE DESCRIBED IN THIS DOCUMENT, YOU OR THE ENTITY OR COMPANY THAT
YOU REPRESENT ("LICENSEE") ARE UNCONDITIONALLY CONSENTING TO BE BOUND BY AND ARE BECOMING A PARTY TO THIS LICENSE
AGREEMENT ("AGREEMENT"). LICENSEE'S USE OR CONTINUED USE OF THE DOWNLOADED OR INSTALLED MATERIALS SHALL ALSO
CONSTITUTE ASSENT TO THE TERMS OF THIS AGREEMENT. IF LICENSEE DOES NOT UNCONDITIONALLY AGREE TO ALL OF THE TERMS
OF THIS AGREEMENT, DO NOT CONTINUE THE INSTALLATION PROCESS. IF THESE TERMS ARE CONSIDERED AN OFFER, ACCEPTANCE IS
EXPRESSLY LIMITED TO AND EXPRESSLY CONTINGENT UPON THESE TERMS. IF YOU ARE ACCEPTING THESE TERMS ON BEHALF OF A
COMPANY, ANOTHER PERSON OR ANY OTHER LEGAL ENTITY, YOU REPRESENT AND WARRANT THAT YOU HAVE THE AUTHORITY TO
BIND THAT COMPANY, PERSON OR ENTITY.

1 LICENSE GRANT. Subject to the terms of this Agreement, Symbol Technologies, Inc. and/or its subsidiaries ("Licensor") hereby grants

Licensee a limited, personal, non-sublicensable, non-transferable, nonexclusive license to use the software that Licensee is about to
download or install and the documentation that accompanies it (collectively, the "Software") for Licensee's personal use in connection
with hardware produced by Licensor and only in accordance with the accompanying documentation. Licensee may download, install
and use the Software only on a single computer. Licensee may make one copy of the Software (excluding any documentation) for
backup purposes, provided that copyright and other restricted rights notices of Licensor and its suppliers are reproduced exactly.

2 LICENSE RESTRICTIONS. Except as expressly permitted by this Agreement, Licensee shall not, nor permit anyone else to, directly or

indirectly: (i) copy (except for one backup copy), modify, distribute or create derivative works based upon the Software; (ii) reverse
engineer, disassemble, decompile or otherwise attempt to discover the source code or structure, sequence and organization of the
Software; or (iii) rent, lease, or use the Software for timesharing or service bureau purposes, or otherwise use the Software for any
commercial purpose/on behalf of any third party. Licensee shall maintain and not remove or obscure any proprietary notices on the
Software, and shall reproduce such notices exactly on all permitted copies of the Software. All title, ownership rights, and intellectual
property rights in and to the Software, and any copies or portions thereof, shall remain in Licensor and its suppliers or licensors.
Licensee understands that Licensor may modify or discontinue offering the Software at any time. The Software is protected by the
copyright laws of the United States and international copyright treaties. The Software is licensed, not sold. This Agreement does not
give Licensee any rights not expressly granted herein.

3 INTELLECTUAL PROPERTY; CONTENT. All title and intellectual property rights in and to the Software (including but not limited to any

images, photographs, animations, video, audio, music, text and "applets" incorporated into the Software), and any copies you are
permitted to make herein are owned by Licensor or its suppliers. All title and intellectual property rights in and to the content which
may be accessed through use of the Software is the property of the respective content owner and may be protected by applicable
copyright or other intellectual property laws and treaties. This EULA grants you no rights to use such content. As a condition to
Licensee's use of the Software, Licensee represents, warrants and covenants that Licensee will not use the Software: (i) to infringe
the intellectual property rights or proprietary rights, or rights of publicity or privacy, of any third party; (ii) to violate any applicable law,
statute, ordinance or regulation; (iii) to disseminate information or materials in any form or format ("Content") that are harmful,
threatening, abusive, harassing, tortuous, defamatory, vulgar, obscene, libelous, or otherwise objectionable; or (iv) to disseminate any
software viruses or any other computer code, files or programs that may interrupt, destroy or limit the functionality of any computer
software or hardware or telecommunications equipment. Licensee, not Licensor, remains solely responsible for all Content that
Licensee uploads, posts, e-mails, transmits, or otherwise disseminates using, or in connection with, the Software.

4 FEES; SUPPORT AND UPGRADES. Licensor may, at Licensor's sole option, provide support services related to the Software ("Support

Services"). Nothing in this Agreement grants Licensee any right to receive any Support Services. Use of any Support Services provided
is governed by the Licensor policies and programs described in the user manual, in "online" documentation, and/or in other
Licensor-provided materials or support agreements. Any supplemental software code provided to you as part of any Support Services
shall be considered part of the Software and subject to the terms and conditions of this EULA. With respect to technical information
you provide to Licensor as part of any Support Services, Licensor may use such information for its business purposes, including for
product support and development. Licensor will not utilize such technical information in a form that personally identifies Licensee.

5 TERMINATION. Either party may terminate this Agreement at any time, with or without cause, upon written notice. Any termination of

this Agreement shall also terminate the licenses granted hereunder. Upon termination of this Agreement for any reason, Licensee

50 AP-8132 Access Point

shall return all copies of the Software to Licensor, or destroy and remove from all computers, hard drives, networks, and other storage
media all copies of the Software, and shall so certify to Licensor that such actions have occurred. Sections 2-13 shall survive
termination of this Agreement.

6 DISCLAIMER OF WARRANTIES. To the maximum extent permitted by applicable law, Licensor and its suppliers provide the Software

and any (if any) Support Services AS IS AND WITH ALL FAULTS, and hereby disclaim all warranties and conditions, either express,
implied or statutory, including, but not limited to, any (if any) implied warranties or conditions of merchantability, of fitness for a
particular purpose, of lack of viruses, of accuracy or completeness of responses, of results, and of lack of negligence or lack of
workmanlike effort, all with regard to the Software, and the provision of or failure to provide Support Services. ALSO, THERE IS NO
WARRANTY OR CONDITION OF TITLE, QUIET ENJOYMENT, QUIET POSSESSION, CORRESPONDENCE TO DESCRIPTION, OR
NON-INFRINGEMENT WITH REGARD TO THE SOFTWARE. THE ENTIRE RISK AS TO THE QUALITY OF OR ARISING OUT OF USE OR
PERFORMANCE OF THE SOFTWARE AND SUPPORT SERVICES, IF ANY, REMAINS WITH LICENSEE.

7 EXCLUSION OF INCIDENTAL, CONSEQUENTIAL AND CERTAIN OTHER DAMAGES. TO THE MAXIMUM EXTENT PERMITTED BY

APPLICABLE LAW, IN NO EVENT SHALL LICENSOR OR ITS SUPPLIERS BE LIABLE FOR ANY GENERAL, SPECIAL, INCIDENTAL, DIRECT,
INDIRECT, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF PROFITS OR
CONFIDENTIAL OR OTHER INFORMATION, FOR BUSINESS INTERRUPTION, FOR PERSONAL INJURY, FOR LOSS OF PRIVACY, FOR
FAILURE TO MEET ANY DUTY INCLUDING OF GOOD FAITH OR OF REASONABLE CARE, FOR NEGLIGENCE, AND FOR ANY OTHER
PECUNIARY OR OTHER LOSS WHATSOEVER) ARISING OUT OF OR IN ANY WAY RELATED TO THE USE OF OR INABILITY TO USE THE
SOFTWARE, THE PROVISION OF OR FAILURE TO PROVIDE SUPPORT SERVICES, OR OTHERWISE UNDER OR IN CONNECTION WITH
ANY PROVISION OF THIS AGREEMENT, EVEN IN THE EVENT OF THE FAULT, TORT (INCLUDING NEGLIGENCE), STRICT LIABILITY,
BREACH OF CONTRACT OR BREACH OF WARRANTY OF LICENSOR OR ANY SUPPLIER, AND EVEN IF LICENSOR OR ANY SUPPLIER
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

8 LIMITATION OF LIABILITY AND REMEDIES. Notwithstanding any damages that Licensee might incur for any reason whatsoever

(including, without limitation, all damages referenced above and all direct or general damages), the entire liability of Licensor and any
of its suppliers under any provision of this Agreement and Licensee's exclusive remedy for all of the foregoing shall be limited to the
greater of the amount actually paid by Licensee for the Software or U.S.$5.00. The foregoing limitations, exclusions and disclaimers
shall apply to the maximum extent permitted by applicable law, even if any remedy fails its essential purpose.

9 INDEMNITY. Licensee agrees that Licensor shall have no liability whatsoever for any use Licensee makes of the Software. Licensee

shall indemnify and hold harmless Licensor from any claims, damages, liabilities, costs and fees (including reasonable attorney fees)
arising from Licensee's use of the Software as well as from Licensee's failure to comply with any term of this Agreement.

10 FAULT TOLERANCE. The Software is not fault-tolerant and is not designed, manufactured or intended for use or resale in on-line

control equipment in hazardous environments requiring fail-safe performance, such as, but not limited to, the operation of nuclear
facilities, aircraft navigation or communication systems, air traffic control, life support machines, or weapons systems, in which the
failure of the Software could lead directly or indirectly to death, personal injury, or physical or environmental damage ("High Risk
Activities"). Licensor and its suppliers specifically disclaim any express or implied warranty of fitness for High Risk Activities.

11 U.S. GOVERNMENT LICENSE RIGHTS. Software provided to the U.S. Government pursuant to solicitations issued on or after

December 1, 1995 is provided with the commercial license rights and restrictions described elsewhere herein. Software provided to
the U.S. Government pursuant to solicitations issued prior to December 1, 1995 is provided with "Restricted Rights" as provided for in
FAR, 48 CFR 52.227-14 (JUNE 1987) or DFAR, 48 CFR 252.227-7013 (OCT 1988), as applicable. The "Manufacturer" for purposes of
these regulations is Symbol Technologies, Inc., One Symbol Plaza, Holtsville, NY 11742.

12 EXPORT RESTRICTIONS. Licensee shall comply with all export laws and restrictions and regulations of the Department of Commerce,

the United States Department of Treasury Office of Foreign Assets Control ("OFAC"), or other United States or foreign agency or
authority, and Licensee shall not export, or allow the export or re-export of the Software in violation of any such restrictions, laws or
regulations. By downloading or using the Software, Licensee agrees to the foregoing and represents and warrants that Licensee is not
located in, under the control of, or a national or resident of any restricted country.

13 MISCELLANEOUS. Licensee may not sublicense, assign, or transfer this Agreement, or its rights or obligations hereunder, without the

prior written consent of Licensor. Any attempt to otherwise sublicense, assign, or transfer any of the rights, duties, or obligations
hereunder is null and void. Licensor may assign this Agreement in its sole discretion. In the event that any of the provisions of this

Installation Guide 51

Agreement shall be held by a court or other tribunal of competent jurisdiction to be illegal, invalid or unenforceable, such provisions
shall be limited or eliminated to the minimum extent necessary so that this Agreement shall otherwise remain in full force and effect.
No waiver or modification of this Agreement will be binding upon a party unless made in writing and signed by a duly authorized
representative of such party and no failure or delay in enforcing any right will be deemed a waiver. This Agreement shall be governed
by the laws of the State of New York without regard to the conflicts of law provisions thereof. The application the United Nations
Convention of Contracts for the International Sale of Goods is expressly excluded. Unless waived by Licensor for a particular instance,
any action or proceeding arising out of this Agreement must be brought exclusively in the state or federal courts of New York and
Licensee hereby consents to the jurisdiction of such courts for any such action or proceeding. This Agreement supersedes all prior
discussions and writings and constitutes the entire agreement between the parties with respect to the subject matter hereof. The
prevailing party in any action arising out of this Agreement shall be entitled to costs and attorneys' fees.

52 AP-8132 Access Point

15

8 AP-8132 Access Point China ROHS Compliance

有害物质

铅

汞

镉

六价铬

多溴联

部件名称

金属部件

(Metal Parts)

电路模块

(Circuit Modules)

电缆及电缆组件

(Cables and Cable Assemblies)

塑料和聚合物部件

(Plastic and Polymeric Parts)

光学和光学组件

(Optics and Optical Components)

电池

(Batteries)

(Parts)

(Pb)

(Hg)

XOOOOO

XOOOOO

XOOOOO

OOOO O O

OOOO O O

OOOO O O

(Cd)

(Cr(VI))

苯

(PBB)

多溴二苯

醚

(PBDE)

本表格依据SJ/T 11364 的规定编制。
O:表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量 要求以下。

X:表示该有害物质至少在该部件的某一均质材料中的含量超出GB/T 26572 规定 的限量要求。(企业可在此处，根
据实际情况对上表中打“×”的技术原因进 行进一步说明。）

This table was created to comply with China RoHS requirements for the AP-8132 Access Point.

Installation Guide 53

Zebra Technologies Corporation
Lincolnshire, IL 60069 USA

Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark of Symbol
Technologies, Inc., a Zebra Technologies company.

© 2015 Symbol Technologies, Inc.

MN001380A01 Revision B April 2015