Syma Toys S6 User Manual

AGES 14+

S

6

3 CHANNEL REMOTE CONTROL HELICOPTER

1

INSTRUCTION MANUAL

IMPLEMENT STANDARD: GB/T26701-2011

Helicopter Features

Special Plastic frame for a good resistance to mill and stable flight.It is suitable for
indoor flight.

A sophisticated built-in gyroscopic auto-stability system for smooth and stable flying.

Model design structured, easy operation and maintenance.

All material, dimensions and spare parts included in this instruction are for reference
only. The company is not responsible for any changes printed parts and notify
consumer. Any updated or changed please refer to our website www.symatoys.com.

BUTTON Description

A/B band selector：system regards to band “A” when
controller turned on. press button “A” for 2 seconds till
indicdtor lights flash twice,controller enter into bank "B",
press button “A” for 2 seconds, indicator lights flash one
time,controller back to band “A”.

HELICOPTER CHARGING

Charging helicopter with USB: Take out the
USB charging wire,connect the USB wire to
the computer interface. then connect the
other USB charging wire to the helicopter
interface. During charging, the indicator of
USBcharging wire will be OFF. When it fully
charged, the indicator will be ON.

Charging time: about 25 - 30 minutes — Flying time: about 5 - 6 minutes!

Note:Make sure helicopter power switch to OFF position when charging.

TROUBLE SHOOTING

Remote control charging

Problem Reson Solution

1.Insufficient power with the helicopter. 1.Please charge to the helicopter.

No response

2.Insufficient power with the transmitter,

from the

power indicator keeps flashing.

helicopter

3.The band of the transmitter does not
correspond to the decoding of the
helicopter.

If the

1.Insuffcient power with the transmitter.

helicopter is

slow to

2.Transmitter of the same frequency is

respond

used nearby.

or difficult to

manoeuver

2.Replace the battery inside the
transmitter.

3.Adjust the band on the transmitter
and keep it the same as the
helicopter.

1.Replace the battery.

2.Use the helicopter out of the range
of other RC helicopters.

-4-

A

ABOUT CONTENTS

Product included
following contents:

Helicopter
Transmitter
Tail blade
Instruction manual
USB cable

GET TO KNOW YOUR TRANSMITTER

Remoter instruction

ON/OFF

Up/Down

High/Low

speed switch

(A/B Band

Selector)

Power/Charge

Indicator

Forward/
Backward
Turn Left/
Turn Right

Turn left

trimmer
Turn right
trimmer

Battery Installation

Cover

4“AAA” batteries

Unscrew and remove battery cover from R/C unit, insert 4“AAA” batteries,noting
polarity indicator. Replace battery cover.

BREAKDOWN & DIAGRAM

产品明细解图

2

4

5

6

-1-

1

3

7

8

9

12

14

15

10

11

13

20

21

19

18

16

17

-5-

READY TO FLY YOUR HELICOPTER

Step 1: Press the power switch
to turn on the transmitter.

CHA

ON

OFF

Code Description Quantity Code Description Quantity

Balance bar

01

Connector buckle

02

Main shaft base

03

Top blades locker

04

05

Top blades

06

07

08

24

09 1

23

10 1

22

11

12

SPARE PARTS

Spindle

Below blades locker

Below blades

Below blades base

Top main stand

Top blade gear

Under blade gear

Step 2: Turn on your helicopter.

Step 3: Transmitter indicator blinks
for about 10-20 seconds to match
signal. When finish matching, it
keeps light on. please push the left
lever backwards to ready flight.

TIPS: When matching signal, keep
the helicopter on horizontal

Horizontal

position for faster matching

position

and starting start a stable flight.

-2-

1

2

1

1

2

1

1

2

1

1

Under main stand

13

Receiver board

14

15

16

17

Top blades locker

18

Below blades locker

19

20

21

22

23

24

Tail cover box

Battery

Left body

Right body

main motor

main motor

Tail tube

Tail dangling

Tail motor

Tail blade

All the spare parts below can bought from local distributor.

S6-01A S6-02 S6-03

Headcover-Blue Headcover-Yellow Main blades Balance bar

S6-04A

Main frame-Blue

S6-01B

S6-04B

Main frame-Yellow Motor A Motor B

S6-05A

-6-

S6-05B

1

1

1

1

1

1

1

1

1

1

1

1

FLIGHT CONTROL

Hover up and down Forward and backward

When the helicoptr fllies
steadity, you canshowly push
the throttle stick up to make
helicopter fly higher, or release
the stick a bit to make helicopter
fly lower. Only small amounts of
stick posoition change are
required for smooth flying.

Turn Left and Right

Hold the helicopter at a height.
Push the rudder stick toward
left to turn counter clockwise,
and push the rudder stick
twoard right to turm clockwise.

S6-06A S6-07 S6-08

Tail assembly

-Blue

S6-09 S6-10

Base

MAIN PARAMETER

Body length: Main blade diameter:
Body width:
Body high:

S6-06B

Tail assembly

-Yellow

Transparent
cover

83mm

25mm

80mm 83mm
25mm
60mm

When you push up the riht
contrl lever (steering rudder),
the nose incline to down, the
helicopter is moving to
forward. When you push down
the right control lever(steering
rudder), the nose incline to up,
the helicopter is moving to
backward.

Turn right/left calibration trim

If helicopter rotates counter

-clockwise…Continually
push right R/C calibration
until excessive turning stops.

If helicopter rotates
clockwise…Continually
push right R/C calibration
until excessive turning stops.

-3-

Battery Receicer board

S6-11 S6-12

USB charger cable Transmitter

Main motor code: ∮6

3.7V 70 mAh Li-poly

Battery:

-7-

60mm

80mm