Sylvania SSC727B User Manual

OWNER’S MANUAL
27-INCH COLOR TV/DVD/VHS
SSC727B
This Owner’s Manual is
made of recycled paper.
If you need additional operating assistance after reading this owner’s manual or to order replacement accessories, please call
TOLL FREE : 1-800-968-3429.
Please read before using this equipment
SUPPLIED ACCESSORIES
ACCESSORIES Remote Control Unit Batteries
PART NO. N0288UD 2 AA Batteries
WARNING:TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSON­NEL.
The caution marking is located on the rear of the cabinet.
IMPORTANT SAFEGUARDS
1.Read instructions-All the safety and operating instructions
should be read before the appliance is operated.
2.Retain Instructions-The safety and operating instructions
should be retained for future reference.
3.Heed Warnings-All warnings on the appliance and in the
operating instructions should be adhered to.
4.Follow Instructions-All operating and use instructions
should be followed.
5.Cleaning-Unplug TV/DVD/VHS from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. EXCEPTION: A product that is meant for uninterrupted service and, that for some specific reason, such as the possi­bility of the loss of an authorization code for a CATV con­verter, is not intended to be unplugged by the user for clean­ing or any other purpose, may exclude the reference to unplugging the appliance in the cleaning description other­wise required in item 5.
6.Attachments-Do not use attachments not recommended by
the TV/DVD/VHS manufacturer as they may cause hazards.
7.Water and Moisture-Do not use this TV/DVD/VHS near
water-for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.
8.Accessories-Do not place this TV/DVD/VHS on an unstable
cart, stand, tripod, bracket, or table. The TV/DVD/VHS may fall, causing serious injury to someone, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the TV/DVD/VHS. Any mounting of the appliance should follow the manufacturer’s instructions and should use a mounting accessory recommended by the manufacturer. An appliance and cart combination should be moved with care.Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.
PORTABLE CART WARNING
S3126A
THIS SYMBOL INDICATES THAT DAN­GEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.
AMEUBLES- Cet appareil ne doit être placé que sur un meuble (avec ou sans roulettes) recommandé par le fabricant. Si vous l’installez sur un meuble à roulettes, déplacez les deux ensembles avec précaution. Un arrêt brusque, l’utilisation d’une force excessive et des sur­faces irrégulières risquent de désta­biliser l’ensemble et de le renverser.
9. Ventilation-Slots and openings in the cabinet and the back
or bottom are provided for ventilation and to ensure reliable operation of the TV/DVD/VHS and to protect it from over­heating, and these openings must not be blocked or cov­ered. The openings should never be blocked by placing the TV/DVD/VHS on a bed, sofa, rug, or other similar surface. This TV/DVD/VHS should never be placed near or over a radiator or heat register. This TV/DVD/VHS should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
10.Power Sources-This TV/DVD/VHS should be operated
only from the type of power source indicated on the mark­ing label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For TV/DVD/VHSs intended to operate from battery power, or other sources, refer to the operating instructions.
11.Grounding orPolarization-This TV/DVD/VHS is
equipped with a polarized alternating-current line plug(a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety fea­ture. If you are unable to insert the plug fully into the out­let, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
12.Power-Cord Protection-Power-supply cords should be
routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying par­ticular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.
SYMBOLE D'AVERTISSEMENT POUR
LES COMPOSANTES
APPAREIL ET MEUBLE A ROULETTES
S3126A
- 2 - EN
1B15
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELE CTRICAL CODE
S2898A
FIGURE A
ELECTRIC SERVICE EQUIPMENT
NEC - NATIO NAL EL ECTR ICAL CODE
GROUND
CLAMP
ANTENNA
LEAD IN WIRE
ANTENNA
DISCHARGE UNI T (NEC SECTIO N 810 -20)
GROUNDING CONDUCTORS (NEC SECTION 810-21)
GROUND CL AMPS
POWER SERVICE GRO UNDING ELECTRODE SYSTEM (NEC ART 250, PART H)
13.Outdoor Antenna grounding-If an outside antenna or
cable system is connected to the TV/DVD/VHS, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA No. 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. (Fig. A)
14.Lightning-For added protection for this TV/DVD/VHS
receiver during a lightning storm, or when it is left unat­tended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the TV/DVD/VHS due to lightning and power-line surges.
15.Power Lines-An outside antenna system should not be
located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
16.Overloading-Do not overload wall outlets and extension
cords as this can result in a risk of fire or electric shock.
17.Object and Liquid Entry-Never push objects of any kind
into this TV/DVD/VHS through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the TV/DVD/VHS.
18.Servicing-Do not attempt to service this TV/DVD/VHS
yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
19.Damage Requiring Service-Unplug this TV/DVD/VHS
from the wall outlet and refer servicing to qualified service
personnel under the following conditions: a. When the power-supply cord or plug is damaged or frayed. b. If liquid has been spilled, or objects have fallen into the
TV/DVD/VHS. c. If the TV/DVD/VHS has been exposed to rain or water. d. If the TV/DVD/VHS does not operate normally by follow-
ing the operating instructions. Adjust only those controls
that are covered by the operating instructions, as improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the TV/DVD/VHS to its normal operation. e. If the TV/DVD/VHS has been dropped or damaged in any
way. f. When the TV/DVD/VHS exhibits a distinct change in per-
formance-this indicates a need for service.
20.Replacement Parts-When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer that have the same character-
istics as the original part. Unauthorized substitutions may
result in fire, electric shock, injury to persons or other haz-
ards.
21.Safety Check-Upon completion of any service or repairs to
this TV/DVD/VHS, ask the service technician to perform
routine safety checks to determine that the TV/DVD/VHS
is in proper operating condition.
22.Heat-This TV/DVD/VHS product should be situated away
from heat sources such as radiators, heat registers, stoves,
or other products (including amplifiers) that produce heat.
CAUTION:TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQUAU FOND.
- 3 - EN
1B15
PRECAUTIONS
IMPORTANT COPYRIGHT INFORMATION
Unauthorized copying, broadcasting, public perfor­mance and lending of discs are prohibited.
FCC WARNING- This equipment may gener­ate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction man­ual. The user could lose the authority to oper­ate this equipment if an unauthorized change or modification is made.
RADIO-TV INTERFERENCE
This equipment has been tested and found to com­ply with the limits for a Class B digital device, pur­suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter­mined by turning the equipment off and on, the user is encouraged to try to correct the interfer­ence by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a cir­cuit different from that to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
LASER SAFETY
This unit employs a laser. Only a qualified service person should remove the cover or attempt to ser­vice this device, due to possible eye injury.
CAUTION: USE OF CONTROLS OR ADJUST­MENTS OR PERFORMANCE OF PROCE­DURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO NOT STARE INTO BEAM.
LOCATION: INSIDE, NEAR THE DECK MECHANISM.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est con­forme à la norme NMB-003 du Canada.
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
- 4 - EN
1B15
LOCATION
For safe operation and satisfactory performance of your TV/DVD/VHS, keep the following in mind when selecting a place for its installation:
Shield it from direct sunlight and keep it away from
sources of intense heat. Avoid dusty or humid places.
Avoid places with insufficient ventilation for proper
heat dissipation. Do not block the ventilation holes at the top and bottom of the unit. Do not place the unit on a carpet because this will block the ventilation holes.
Install unit in a horizontal position.
Avoid locations subject to strong vibration.
Do not place the TV/DVD/VHS near strong magnetic
fields. Avoid moving TV/DVD/VHS to locations where
temperature differences are extreme.
AVOID THE HAZARDS OF
ELECTRICAL SHOCK AND FIRE
Do not handle the power cord with wet hands.
Do not pull on the power cord when disconnecting
it from an AC wall outlet. Grasp it by the plug. If, by accident, water is spilled on your unit, unplug
the power cord immediately and take the unit to our Authorized Service Center for servicing.
Do not put your fingers or objects into the
TV/DVD/VHS disc loading tray. Do not place anything directly on top of the unit.
WARNING
Moisture condensation may occur inside the unit when it is moved from a cold place to a warm place, or after heating a cold room or under conditions of high humidity. If a DVD is played in a TV/DVD/ VHS which has moisture, it may damage the DVD and TV/DVD/VHS. Therefore when the condensation occurs inside the unit, turn the POWER button on and allow at least 2 hours for the unit to dry out.
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula­tions concerning chemical wastes.
The serial number of this product may be found on the back of the unit. No other TV/DVD/VHS has the same serial number as yours. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.
Date of Purchase Dealer Purchase from Dealer Address Dealer Phone No. Model No. Serial No.
- 5 - EN
1F12
TABLE OF CONTENTS
C IMPORTANT SAFEGUARDS . . . . .2
C PRECAUTIONS . . . . . . . . . . . . . . . .4
LOCATION . . . . . . . . . . . . . . . . . . .5
AVOID THE HAZARDS OF ELECTRICAL SHOCK AND FIRE .5
WARNING . . . . . . . . . . . . . . . . . . . .5
C FEATURES . . . . . . . . . . . . . . . . . . . .7
C OPERATING CONTROLS AND
FUNCTIONS . . . . . . . . . . . . . . . . . . .9
C PREPARATION FOR USE . . . . . . .11
ANTENNA/CABLE
CONNECTIONS . . . . . . . . . . . . . . .11
CONNECTING TO EXTERNAL
INPT JACKS . . . . . . . . . . . . . . . . .12
INSTALLING THE BATTERIES . .12
EXTERNAL INPUT MODE . . . . . .12
CONNECTING TO ASTEREO
SYSTEM (for DVD) . . . . . . . . . . . .13
CONNECTING TO AN AMPLIFIER EQUIPPED WITH DIGITALINPUT JACKS, MD DECK OR DAT DECK
(for DVD) . . . . . . . . . . . . . . . . . . . .13
CONNECTING TO ADOLBY DIGITALDECODER OR DTS DECODER (for DVD) . . .14
C SET UP FOR USE . . . . . . . . . . . . .15
CHANNEL SET UP
FOR THE FIRST TIME . . . . . . . . .15
DELETING (OR ADDING)
CHANNEL . . . . . . . . . . . . . . . . . . .15
CHANNEL SET UP AGAIN . . . . . .16
SELECTING THE LANGUAGE . .16
DAYLIGHT-SAVING TIME . . . . . .16
CLOCK SET UP
(AUTO / MANUAL) . . . . . . . . . . . .17
TV/VCR SECTION
C TV OPERATION . . . . . . . . . . . . . . .19
WATCHING ATV PROGRAM . . .19
DEGAUSSING . . . . . . . . . . . . . . . .19
PICTURE CONTROL . . . . . . . . . . .19
CLOSED CAPTION SYSTEM . . . .20
V-CHIP SET UP . . . . . . . . . . . . . . .21
C MTS(Multi-Channel Television
sound)SYSTEM . . . . . . . . . . . . . . . .23
CHECKING THE SELECTED
MTS MODE . . . . . . . . . . . . . . . . . .23
MTS RECORDING/MONITOR
MODE . . . . . . . . . . . . . . . . . . . . . .23
SELECTING THE MTS SYSTEM .24
C VIDEO CASSETTE . . . . . . . . . . . . .25
CC
PLAYBACK . . . . . . . . . . . . . . . . . . .26
NORMAL PLAYBACK . . . . . . . . .26
TRACKING ADJUSTMENT . . . . .26
SLOW MOTION . . . . . . . . . . . . . .26
PICTURE SEARCH . . . . . . . . . . . .26
STILL PICTURE . . . . . . . . . . . . . .26
VERTICALHOLD CONTROL . . .26
C SPECIAL PLAYBACK . . . . . . . . . .27
RENTALPLAYBACK . . . . . . . . . .27
AUTO REPEAT PLAYBACK . . . . .27
C SEARCH . . . . . . . . . . . . . . . . . . . . .28
ZERO RETURN . . . . . . . . . . . . . . .28
TIME SEARCH . . . . . . . . . . . . . . .28
INDEX SEARCH . . . . . . . . . . . . . .29
C SPECIAL FEATURES . . . . . . . . . .29
REAL TIME TAPE COUNTER . . .29
AUTO REWIND-EJECT . . . . . . . .29
C RECORDING . . . . . . . . . . . . . . . . .30
NORMAL RECORDING . . . . . . . .30
SKIPPING UNWANTED SCENES
DURING RECORDING . . . . . . . . .30
OTR (One Touch Recording) . . . . . .31
COPYING A VIDEO CASSETTE (Requires a VCR or camcorder) . . .31
C TIMER . . . . . . . . . . . . . . . . . . . . . .32
AUTOMATIC
TIMER RECORDING . . . . . . . . . .32
TIMER PROGRAM EXTENSION .33 HINTS FOR AUTOMATIC TIMER
RECORDING . . . . . . . . . . . . . . . . .34
AUTO RETURN . . . . . . . . . . . . . . .34
SLEEP TIMER . . . . . . . . . . . . . . . .34
C ON SCREEN DISPLAY . . . . . . . . .35
C CABLE CHANNEL
DESIGNATIONS . . . . . . . . . . . . . .35
D
VD SECTION
C ABOUT THE DISCS . . . . . . . . . . . .36
PLAYABLE DISCS . . . . . . . . . . . .36
DISC TYPES . . . . . . . . . . . . . . . . .36
SYMBOLS USED IN
THIS MANUAL . . . . . . . . . . . . . . .36
C PLAYING ADISC . . . . . . . . . . . . . .37
PLA YING ADVD VIDEO OR AN AUDIO CD
USING THE DVD MENUS . . . . . .36
USING THE TITLE MENU . . . . . .36
RESUMING PLAYBACK FROM THE POINT WHERE
PLAYBACK STOPPED . . . . . . . . .38
FAST FORWARD/REVERSE . . . . .38
PAUSING PLAYBACK OR DIS-
PLAYING A STILL PICTURE . . . .38
STEPPING THROUGH FRAMES .38
SLOW MOTION . . . . . . . . . . . . . .39
PLAYING FROM A DESIRED
TITLE OR CHAPTER . . . . . . . . . .39
STARTING FROM A DESIRED TIME COUNT
STARTING FROM A DESIRED
TRACK . . . . . . . . . . . . . . . . . . . . . .39
REPEAT . . . . . . . . . . . . . . . . . . . . .40
A-B REPEAT . . . . . . . . . . . . . . . . .40
PROGRAM (Audio CD) . . . . . . . . .41
RANDOM (Audio CD) . . . . . . . . . .41
ZOOM PLAYBCK . . . . . . . . . . . . .41
C SETTINGS . . . . . . . . . . . . . . . . . . .42
CHANGING THE AUDIO LANGUAGE OR SOUND MODE .42
CHANGING THE SUBTITLE
LANGUAGE . . . . . . . . . . . . . . . . .43
CHANGING THE CAMERA
ANGLE (Multi-Angle Pictures) . . . .43
CHANGING THE ON-SCREEN
DISPLAY . . . . . . . . . . . . . . . . . . . .44
C CHANGING THE SETUP ITEMS .45
LANGUAGE SETTINGS . . . . . . . .45
VIDEO SETTINGS . . . . . . . . . . . . .46
AUDIO SETTINGS . . . . . . . . . . . .46
PARENTALLOCK . . . . . . . . . . . . .47
OTHER SETTINGS . . . . . . . . . . . .48
C LANGUAGE CODE LIST . . . . . . . .49
C TROUBLESHOOTING GUIDE . . .50
C MAINTENANCE . . . . . . . . . . . . . . .53
DISC HANDLING . . . . . . . . . . . . .53
C SPECIFICATIONS . . . . . . . . . . . . .54
C WARRANTY . . . . . . . . . . .Back Cover
. . . . . . . . . . . . . . . . . . .36
. . . . . . . . . . . . . . . . .39
- 6 - EN
1F12
FEATURES
TV/VCR
Hi-Fi system
offers you excellent sound quality with a dynamic range of 80dB, frequency response from 20Hz to 20kHz, and 0.005% wow and flutter.
Rotary 4-head Record/Playback System–Four heads
ensure excellent picture quality and special effects playback.
Index Search–
Slow Motion–View recorded program at slower
than normal speed.
Trilingual on screen tv/vcr setup display selec-
table in English or Spanish or French Real time counter–This shows the elapsed recording
or playback time in hours, minutes, and seconds. “–” indication will appear when the tape is rewound further than the tape counter position “0:00:00”.
181 channel capability PLL frequency synthesiz-
er tuner with direct station call–
be necessary to view scrambled cable channels.)
Auto Clock Setting–Allows you to set the clock
function from a PBS broadcast station.
Closed caption system–You may view specially
labeled (cc) TV programs, movies, news, prere­corded tapes, etc. with either a dialogue caption or text display added to the program.
Auto power on and off system–Automatically
turns on the TV/DVD/VHS when you insert the cassette, turns off after auto-rewind, and ejects when the beginning of the tape is reached.
Auto rewind when the end of a tape is
reached–
timer recording.
The Hi-Fi stereo recording system
Fast-forwards to start of next recording.
(A converter may
This function doesn’t occur when using
The
2 Step picture search operation–You can view a
video program at a high speed or super high speed in either a forward or reverse direction in LP and SLP mode. For SP mode only high speed.
Three different playback tape speeds : SP/LP/SLP
Two different recording tape speeds : SP/SLP
Auto Head Cleaner–Automatically cleans video
heads as you insert or remove a cassette.
Zero Return–The tape returns to counter of
0:00:00 by rewinding or fast forwarding.
Still–“Freeze” the picture at any time, for close
viewing of a particular scene.
Digital Auto Tracking (DTR)–Automatically
adjusts the tracking for each tape you play.
Rental play mode–Improves playback picture
quality from worn tapes, such as rental tapes.
Auto repeat–Allows you to repeat the playing of a
tape indefinitely without pressing the PLAY button.
Time search–Let you set the TV/DVD/VHS to
advance the tape by entering the desired playback time you want to skip.
OTR (One Touch Recording)–Instant timed
recording from 30 to 480 minutes is possible at the push of the REC/OTR button.
1 Year, 8 events (including Daily and Weekly
Timer Recording)–
record up to 8 programs at different times on dif­ferent channels up to 1 year in advance. The Daily timer allows recordings to be made of daily broad­casts, and the Weekly timer allows recording to be made once a week up to the end of the tape.
Auto return–After timer recording is finished, the
TV/DVD/VHS can return to the beginning of the recording.
Sleep timer–Allows you to have the
automatically turn on or off at a desired time. (This feature is not available for DVD mode.)
Timer Program Extension–Allow you to shift the
time schedule for automatic timer recording.
V-CHIP–Enables parents to prevent their children
from watching inappropriate material on TV.
The built-in timer allows you to
TV/DVD/VHS
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula­tions concerning chemical wastes.
- 7 - EN
1F12
DVD
¡Dolby Digital sound
This player can handle Dolby Digital surround sound having 5.1 channels when connected to a Dolby Digital decoder.
¡Still/fast/slow/step playback
Various playback modes are available including still pic­tures, fast forward/reverse, slow motion and step frames.
¡Random playback for audio CD
This player can shuffle the order of tracks to play them in random order.
¡Program playback for audio CD
You can program the order of tracks to play them in any desired order.
¡DVD menus in a desired language
You can display DVD menus in a desired language, if available on a DVD.
¡Screen saver/Auto power-off functions
The screen saver program starts when there is no input from the player for five minutes in the stop mode. When the screen saver program is activated for 30 minutes, the DVD power is automatically turned off, and "DVD" appears on the screen.
¡Subtitles in a desired language
You can select a desired language for the display subtitles, if that language is available on a disc.
¡Selecting a camera angle
You can select the desired camera angle, if a disc contains sequences recorded from different angles.
¡Choices for audio language and sound mode
You can select the desired audio language and sound mode, if different languages and modes are available on a disc.
¡Parental lock
You can set the control level to limit playback of discs which may not be suitable for children.
¡Automatic detection of discs
This player automatically detects if a loaded disc is DVD or audio CD.
¡On-screen display
Information about the current operation can be displayed on a TV screen, allowing you to confirm the currently active functions (such as program playback), on the TV screen using the remote control.
¡DTS (Digital Theater System)
Sound system different from Dolby Digital sound system
¡Search
Chapter search: Search for the chapter designated by user Title search: Search for the title designated by user is Track search: Search for the track designated by user is Time search: Search for the time designated by user is
¡Repeat
Chapter: Repeated playback of the chapter of the Title: Repeated playback of the title of the disc Track: Repeated playback of the track of the disc
(audio CD)
Disc
A-B: The part between A and B designated by
¡Zoom
4-time magnified screen can be displayed.
¡Marker
The part designated by user can be called back.
¡Resume Play
User can resume to playback from the part at which the play was stopped.
¡SRS T ruSurround
You can enjoy stereophonic virtual space on your existing stereo system.
¡Dimmer
Brightness of the display can be varied.
¡Bit rate indication ¡Dynamic range control
This unit employs TruSurround system of SRS Labs, Inc. as virtual
technology. TruSurround and the symbol are trademarks of
SRS Labs, Inc. TruSurround technology is incorporated under license
from SRS Labs, Inc.
is possible. possible. possible. possible.
disc being played is possible. being played is possible. being played is possible.
: Repeated playback of the entire disc being
played is possible.
user is possible.
NOTE:
We do not recommend the use of universal remote controls. Not all of the functions may be controlled with
a universal remote control. If you decide to use a universal remote control with this unit, please be aware that the code number given
may not operate this unit. In this case, please call the manufacturer of the universal remote control.
- 8 - EN
1F12
OPERATING CONTROLS AND FUNCTIONS
- TV/DVD/VHS FRONT PANEL - [Fig.1]
POWER
VOLUME
PLAY
SKIP
SKIP
SEARCH
12 4 5 6 107 1514983 3 411 12 13 212019181716
- REMOTE CONTROL -
POWER PICTURE TV/VCR
[Fig. 2]
DVD
1
22 23
24 25
123 456 789
PAUSE
SPEED C.RESET
+100
0 +10
CH.
VOL.
MUTEZOOM
26
(DVD) 3
(TV/VCR) 14
4
13 27
28 29 30
31 32
RECORD
DISPLAY
CLEAR
MODE
PLAY
STOP
ENTER
REPEATSEARCH MODE
DISC
MENU
RETURNTITLESETUP
ANGLESUBTITLEAUDIO
SLEEP
A
-
B
33
POWER button
1.
Press to turn the power on and off.
2.VOLUME K/L buttons
Press to control the volume level for the DVD and TV.
3.SKIP buttons (for DVD)
Skip chapters or tracks to a desired point. Press and hold in a second or more to get the function of fast forward or fast reverse.
PLAY button
4.
Starts playback of the disc or tape contents.
STOP button(Front Panel)
5.
Stops operation of the disc.
STOP button(Remote Control)
Stops operation of the disc or the tape.
OPEN/CLOSE
STOP
45 44
11
2 43
42
3 (DVD)
15 (TV/VCR)
5 41
40 39
38 37
36 35
34
CHANNEL
REC/OTR
SELECT
TV/VCR
DVD
F.FWD
PLAY
REW
6.OPEN/CLOSE button
Press to insert discs into or remove them from the tray.
Disc loading tray
7.
8.DVD indicator
Lights on during DVD mode.
SELECT button
9.
Press to change to TV/VCR mode or DVD mode. NOTE: For about 4 seconds jast after the DVD mode has switched to the TV mode, the button does not work to switch back to the DVD mode.
TV/VCR indicator
10.
Lights on during TV/VCR mode.
CHANNEL K/L buttons
11.
Press to select memorized channel.
Recording indicator
12.
Flashes during recording. Lights up in the Stand­by mode for Timer Recording.
13.REC/OTR (RECORD) button
Press for manual recording. Activates One Touch Recording. (OTR is only during TV/VCR mode)
REW button (for TV/VCR)
14.
Press to rewind the tape, or to view the picture rapidly in reverse during playback mode. (Rewind Search)
FWD button (for TV/VCR)
15.
Press to rapidly advance the tape, or to view the picture rapidly in forward during playback mode. (Forward Search)
STOP/EJECT button
16.
Press to stop the tape motion. Press in the Stop mode to remove tape from the unit.
Remote sensor window
17.
18.HEADPHONE jack
To connect headphone (not supplied) for personal listening.
VIDEO input jack
19.
Connect to the video output jack of a video camera or VCR.
STOP/EJECT
HEADPHONE
RL
AUDIO
VIDEO
- 9 - EN
1F12
1
ANT.
L
AUDIO OUT
R
COAXIAL
46 47 48 49
- TV/DVD/VHS REAR PANEL - [Fig.3]
20.AUDIO L/R input jacks
Connect to the audio output jacks of a video camera or VCR.
Cassette compartment
21.
22.PICTURE button
Press to adjust the picture.
Number buttons
23.
TV Mode:
Press two digits to directly access the desired channel. Remember to press a "0" before a single digit channel.
+100 button–
Press to select cable channels which are equal or greater than number 100.
DVD Mode:
Press to enter the desired number.
+10 button–
Press to enter the desired numbers which are equal or greater than number 10.
PAUSE button
24.
Pauses the current disc or tape operation.
SPEED button
25.
Press to choose the desired recording speed: SP/SLP.
C.RESET button
26.
Press to reset counter to 0:00:00. Press to cancel a setting of timer program. (See page 33.)
DISPLAY button
27.
TV/VCR Mode:
Display the counter or the current channel number and current time on the TV screen.
DVD Mode:
Displays the current status on the TV screen for checking purposes.
SETUP button
28.
Press to enter or exit the TV menu or DVD setup mode.
TITLE button
29.
Displays the title menu.
CLEAR button
30.
Resets a setting.
31.
MODE button
Activates program playback or random playback mode.
32.SEARCH MODE button
Press to locate a desired point.
AUDIO button
33.
Press to select a desired audio language or sound mode.
SUBTITLE button
34.
Press to select a desired subtitle language.
REPEAT button
35.
Repeats playback of the current disc, title, chapter or track.
ANGLE button (DVD mode)
36.
Press to change the camera angle to see the sequence being played back from a different angle.
SLEEP button (TV/VCR mode)
Sets the Sleep Timer. (See page 34.)
A-B REPEAT button
37.
Repeats playback of a selected section.
RETURN button
38.
Returns to the previous operation.
ENTER button
39.
Press to accept a setting.
Arrow buttons
40.
TV/VCR Mode:
Press to select a setting mode from the menu on the TV screen. Press to select or adjust from a particular menu.
DVD Mode:
Use when making settings while watching the display on a TV screen.
DISC MENU button
41.
Displays the menus in the DVD.
ZOOM Button
42.
Enlarges part of a DVD-reproduced image.
43.MUTE button
Mutes the sound. Press it again to resume sound.
DVD button
44.
Press to switch to DVD mode. DVD indicator on the front will lights on.
- 10 - EN
1F12
ANT.
IN
OUT
1
ANT.
L
AUDIO OUT
R
COAXIAL
45.TV/VCR button
Press to switch to TV/VCR mode. TV/VCR indi­cator on the front will lights on.
ANT. in jack
46.
Connect to an antenna, cable system, or satellite system.
Power cord
47.
Connect to a standard AC outlet (120V/60Hz).
NOTE: Remove the power cord from the hook to
avoid breaking a wire before you connect to a standard AC outlet.
PREPARATION FOR USE
ANTENNA/CABLE CONNECTION
COAXIAL digital audio out jack
48.
Connect to the digital input of an external amplifier or decoder.
AUDIO L/R output jack
49.
Connect to the analog audio input of an external amplifier or decoder.
Satellite Box or Cable Box (Not supplied)
From Cable System or Satellite Dish
75-ohm From Cable System
Coaxial
Cable
(Not sup-
plied)
75-ohm Coaxial Cable (Not
or
supplied)
VHF/UHF SEPARATE ANTENNAS
In some areas it will be necessary to use an outdoor antenna.
CABLE WITHOUT CONVERTER/ DESCRAMBLER BOX
Use this connection if your cable system connects directly to your TV/DVD/VHS without a converter box.
By using this connection you can:
1) Use the TV/DVD/VHS remote to select channels.
2) Program one or more unscrambled channels for Automatic Timer Recording.
NOTE: This unit will ONL same channel.
Y record and view the
VHF/UHF Antenna (Not supplied)
VHF Antenna (Not supplied)
UHF Antenna (Not supplied)
or
VHF/UHF Combiner (Not supplied)
[Fig. 4]
or
Flat twin-lead cable
CABLE WITH CONVERTER/ DESCRAMBLER BOX OR SATELLITE BOX
If your cable service supplies you with a converter box or if you use a satellite system, you can use the basic connection shown in the ilustration.
By using this connection you can also record scram­bled channels. However, channel selection must be made with the converter box or satellite box. This means that channels cannot be changed using the TV/DVD/VHS Remote Control. Unattended timer recording is limited to one channel at a time.
Antenna/Cable Connections Continued on the Next Page.
- 11 - EN
1F12
TO RECORD A SCRAMBLED/UNSCRAM-
VIDEO
HEADPHONE
RL
AUDIO
BLED CHANNEL
1. Set the TV/DVD/VHS channel selector to the out­put channel of the Cable Converter Box or Satellite Box. (Ex. CH3)
2.Select the channel to record from your Cable
Converter Box or Satellite Box.
Note to CATV system installer:
This reminder is provided to call the CATV sys­tem installers attention to Article 820-40 of the NEC that provides guidelines for proper ground­ing and, in particular, specifies that the cable ground shall be connected to the grounding sys­tem of the building as close to the point of cable entry as practical.
INSTALLING THE BATTERIES
1)Open the battery compartment cover by pressing the cover on the remote unit in the direction of the arrow.
2)Insert 2 AA penlight batteries into the battery compartment in the direction indicated by the polarity (+/-) markings.
3)Replace the cover.
EXTERNAL INPUT MODE
CONNECTING TO EXTERNAL
INPUT JACKS
When you watch a program recorded on an another source (VCR or video camera), use the audio/video input jacks on the front of the TV/DVD/VHS.
Connect the audio/video output jacks of another source to the AUDIO L/R and VIDEO jacks of this TV/DVD/VHS.
Then press the SELECT button until "VIDEO" appears on the screen.
NOTE:
When you connect a monaural VCR (another
source) to this TV/DVD/VHS, connect the Audio output jack of the monaural VCR (another source) to the AUDIO L jack of this TV/DVD/VHS. The audio will output in both L and R channel equally.
To the audio output jacks
[Another source]
Audio/Video coaxial cable (not supplied)
etc.
To the video output jack
[Front of the TV/DVD/VHS]
[Fig. 5]
When using an external input signal (another VCR or video camera), connect the players audio/video out­put cables to the AUDIO L/R IN/ VIDEO IN jacks of your
AUX
TV/DVD/VHS. Then press the CHANNEL K or L button until AUX appears on the screen.
- 12 - EN
1F12
CONNECTING TO A STEREO SYSTEM (for DVD)
1
L
AUDIO OUT
R
COAXIAL
To Right (red) and Left (white) AUDIO OUT jacks (only DVD AUDIO OUT)
Stereo system
To ANALOG AUDIO INPUT jacks
1
L
AUDIO OUT
R
COAXIAL
Amplifier equipped with digital
input jacks, MD deck,
DAT deck, etc.
To COAXIAL DIGITAL AUDIO INPUT jack
To DIGITAL AUDIO OUT (PCM/BITSTREAM) COAXIAL jack
(only DVD AUDIO OUT)
NOTES:
Be sure to turn off the power to all components in the system before connecting another component.
Refer to the Owner's Manuals for your, stereo system and any other components to be connected to the
TV/DVD/VHS.
CONNECTING TO AN AMPLIFIER EQUIPPED WITH DIGIT AL
INPUT JACKS, MD DECK OR DAT DECK (for DVD)
[Fig. 6]
Use an audio coaxial digital cable (commercially available) for the audio connections.
[Fig. 7]
NOTES:
The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital
sound by an MD or DAT deck. Be sure to turn off the power to all components in the system before connecting another component.
Refer to the Owner's Manuals for the components to be connected to the TV/DVD/VHS.
Set DOLBY DIGITAL and DTS to OFF for audio output in the setup mode. Playing a TV/DVD/VHS using
incorrect settings may generate noise distortion, and may also damage the speakers. When DOLBY DIGITAL is set to OFF and VIRTUAL 3D to ON for audio output in the setup mode and
you select the audio source in a 5.1 channel Dolby Digital surround format, the audio will be muted.
- 13 - EN
1F12
CONNECTING TO A DOLBY DIGITAL DECODER
1
L
AUDIO OUT
R
COAXIAL
Front speaker
(left)
Center speaker
Front speaker
(right)
Surround
speaker
(left)
Surround
speaker
(right)
Subwoofer
To DIGITAL AUDIO OUT (PCM/BITSTREAM) COAXIAL jack
To COAXIAL DIGITAL AUDIO INPUT jack
Dolby Digital
or DTS decoder
OR DTS DECODER (for DVD)
If using this TV/DVD/VHS to play back a TV/DVD/VHS in a 5.1 channel Dolby Digital surround or DTS surround format, the TV/DVD/VHS outputs a Dolby Digital or DTS data stream from its COAXIAL digital audio out jack. By hooking the player up to a Dolby Digital or DTS decoder, you can enjoy a more convinc­ing, realistic ambience with powerful and high-quality surround sound of a professional standard such as can be heard in movie theaters.
Use audio coaxial digital cables (commercially available) for the audio connections.
[Fig. 8]
NOTES:
Be sure to turn off the power to all components in the system before connecting another component.
Refer to the Owner's Manuals for the components to be connected to the TV/DVD/VHS.
If connected to a Dolby Digital decoder, set DOLBY DIGITAL to ON for audio output in the setup mode.
If connected to a DTS decoder, set DTS to ON for audio output in the setup mode.
Unless connected to a Dolby Digital decoder or a DTS decoder, set DOLBY DIGITAL and DTS to OFF for
audio output in the setup mode. Playing a TV/DVD/VHS using incorrect settings may generate noise distor­tion, and may also damage the speakers.
When DOLBY DIGITAL is set to OFF and VIRTUAL 3D to ON for audio output in the setup mode and
you select the audio source in a 5.1 channel Dolby Digital surround format, the audio will be muted.
Manufactured under license from Dolby Laboratories.Dolbyand the double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished Works. ©1992-1997 Dolby Laboratories, Inc.
All rights reserved.
DTSand DTS Digital Outare trademarks of Digital Theater Systems, Inc.
- 14 - EN
1F12
TV/VCR SECTION
SET UP FOR USE
You can program the tuner to scan all the channels you receive in your area. NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just
select the TV/DVD/VHS channel selector to the output channel of the cable box or satellite box (Ex CH3). Then select the channel to be viewed on the Cable Box or Satellite Box.
CHANNEL SET UP FOR THE
FIRST TIME
1 Plug in the TV/DVD/VHS power cord
Plug the TV/DVD/VHS power cord into a standard AC outlet.
NOTE:
If some digits appear in the corner of
the screen, press the POWER button without unplugging the power cord.
2 Turn on the TV/DVD/VHS
Press the POWER button to turn on the TV/DVD/VHS.
3 Select “ENGLISH or ESPAÑOL or
FRANÇAIS
Select ENGLISH orESPAÑOL”=Spanish orFRANÇAIS =French using the
Arrow B or s button. [ ] indi­cate the selected language.
4 Begin auto preset
Press the Arrow K or L button to point to AUTO PRESET”.
Then press the Arrow B button. The tuner scans and memorizes all
active channels in your area.
NOTES:
The TV/DVD/VHS distinguishes between standard
TV channels and cable channels. If you want to play or record a video tape
BEFORE presetting the tuner, you must press the SETUP button on the remote control. To preset the tuner again, see CHANNEL SET UP AGAIN on page 15.
The TV/DVD/VHS may memorize TV channels as
CATV channels if reception conditions is poor. If this happens, try AUTO MEMO action again when reception conditions are better.
5 After scanning
The tuner stops on the lowest memorized channel. If you want to recall the selected channels, you can
select the desired channel directly with the remote control number buttons or CHANNEL K or L.
– SET UP –
B LANGUAGE
[ENGLISH] ESP FRA
AUTO PRESET
– SET UP –
LANGUAGE [ENGLISH] ESP FRA
B AUTO PRESET
DELETING (OR ADDING)
CHANNEL
The channels you no longer receive or seldom watch can be deleted from the memory. (Of course, you can add the deleted channel into the memory again.)
1 Select CHANNEL SET UP
Press the SETUP button on the remote control.
Press the Arrow K or L button to point to CHANNEL SET UP”.
Then, press the Arrow B button.
2 Select ADD/DELETE CH
Press the Arrow K or L button to point to ADD/DELETE CH”.
Press the Arrow B button.
3 Enter the desired channel number
Press the Arrow K or L button until your desired channel number appears. (You can also use the num­ber buttons or the CHANNEL K/L button to enter it) (Example: CH8)
4 Delete (or add) it from (into) memory
Press the Arrow B or s button. The channel number changes to light red. The channel is deleted from memory.
To delete another channel, repeat steps [3] and [4].
If you press the Arrow B or s button again, the
channel is memorized again.
5 Exit the channel setup mode
Added channel: Light blue. Deleted channel: Light red.
Press the SETUP button on the remote control to returns to TV mode.
NOTE: To confirm that channel(s) has been deleted or added, press the CHANNEL K or L button.
- TV/VCR SETUP -
TIMER PROGRAMMING SETTING CLOCK
B CHANNEL SET UP
USER’S SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] ZERO RETURN TIME SEARCH INDEX SEARCH
– CHANNEL SET UP –
B ADD / DELETE CH (TV)
AUTO PRESET
ADD / DELETE
08
- 15 - EN
1F12
CHANNEL SET UPAGAIN
Make sure ...
Press the POWER button to turn on the
TV/DVD/VHS.
NOTE: If Spanish or French is selected accidentally, press the SETUP button on the remote control, press the Arrow K button to point to IDIOMA [ESPAÑOL] or LANGAGE [FRANÇAIS], then press the Arrow B button, then press the SETUP button on the remote control.
1 Select CHANNEL SET UP
Press the SETUP button on the remote control.
Press the Arrow K or L button to point to CHANNEL SET UP”.
- TV/VCR SETUP -
TIMER PROGRAMMING SETTING CLOCK
B CHANNEL SET UP
USER’S SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] ZERO RETURN TIME SEARCH INDEX SEARCH
Then, press the Arrow B button.
2 Begin auto preset
Press the Arrow K or L button to point to AUTO PRESET”.
– CHANNEL SET UP –
ADD / DELETE CH (TV)
B AUTO PRESET
Then, press the Arrow B button. The tuner scans and memorizes all
the active channels in your area.
3 After scanning
The tuner stops on the lowest memorized channel.
SELECTING THE LANGUAGE
Make sure ...
Press the POWER button to turn on the
TV/DVD/VHS.
NOTE: This function effects only the language on the screen menu and not the audio source.
1 Select LANGUAGE
Press the SETUP button on the remote control.
Press the Arrow K or L button to point to LANGUAGE”.
2 Select “ENGLISH or ESPAÑOL or
FRANÇAIS
Select ENGLISH or ESPAÑOL= Spanish orFRANÇAIS= French using the Arrow B or s
button.
3 Exit the Language mode
Press the SETUP button on the remote control to return to TV mode.
- TV/VCR SETUP -
TIMER PROGRAMMING SETTING CLOCK CHANNEL SET UP USER’S SET UP V-CHIP SET UP
B LANGUAGE [ENGLISH]
CAPTION [OFF] ZERO RETURN TIME SEARCH INDEX SEARCH
DAYLIGHT-SAVING TIME
Select this feature and the TV/DVD/VHS’s clock automatically will advance one hour in April, then reverse one hour in October.
When Daylight-Saving Time is ON, the clock will change automatically as follows:
First Sunday of April : At 2 AM the clock imme-
diately changes to 3 AM. Any timer programming you have set to occur between 2 AM and 3 AM will not record.
Last Sunday of October : At 2 AM the clock
immediately changes to 1 AM.
Make sure ...
Press the POWER button to turn on the
TV/DVD/VHS.
1 Select SETTING CLOCK
Press the SETUP button on the remote control.
Press the Arrow K or L button to point to SETTING CLOCK”.
Then, press the Arrow B button.
2 Set D.S.T. (Daylight-Saving Time) to [ON]
Press the Arrow K or L button to point to D.S.T.”.
Then, press the Arrow B or s but­ton until [ON] appears.
3 Exit the Daylight-Saving Time mode
Press the SETUP button on the remote control to return to TV mode.
TO CANCEL THE DAYLIGHT-SAVING TIME
Repeat steps [1] to [2], select [OFF] using the Arrow B or s button.
- TV/VCR SETUP -
TIMER PROGRAMMING
B SETTING CLOCK
CHANNEL SET UP USER’S SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] ZERO RETURN TIME SEARCH INDEX SEARCH
– SETTING CLOCK –
AUTO CLOCK [ON] AUTO CLOCK CH [AUTO]
MANUAL CLOCK SET
B D.S.T. [ON]
- 16 - EN
1F12
CLOCK SET UP
(AUTO / MANUAL)
Set the clock accurately for proper automatic timer recording. If the Public Broadcasting Station (PBS) is available in your area, follow AUTO CLOCK SET­TING. If it is not, follow MANUAL CLOCK SET­TING”.
AUTO CLOCK SETTING
You can have the TV/DVD/VHS set the clock auto­matically by using the Public Broadcasting Station (PBS) channel in your area. Once you have set the clock by using the following procedure, the TV/DVD/VHS will automatically monitor the correct time and date being broadcast by the PBS station in your area, using a new service called Extended Data Service (XDS).
Make sure ...
TV/DVD/VHS power must be turned on.
Confirm that the antenna connections are correct.
The cable converter box must be turned on if your
TV/DVD/VHS is connected directly to it. (See NOTES:)
The channel is properly set in advance. (See page
16.)
NOTES:
Auto clock setting only needs to be set once. But it
can be done again if the clocks time has become incorrect for some reason.
If the TV/DVD/VHS is connected directly to a
cable converter box or satellite box, the local PBS station must be selected on the cable box itself, and the TV/DVD/VHS must be set to the output chan­nel of the cable converter box or satellite box (usu­ally channel 3 or 4), to be able to set up or correct the clock automatically.
If you do not know what your local PBS station is, then follow Manual Clock Settings on page 18.
The TV/DVD/VHS cannot control the channels of the cable converter box or satellite box.
2 Set AUTO CLOCK to [ON]
Press the Arrow B or s button repeatedly until [ON] appears.
– SETTING CLOCK –
B AUTO CLOCK [ON]
AUTO CLOCK CH [AUTO]
MANUAL CLOCK SET D.S.T. [OFF]
3 Enter the channel number for the PBS station
Press the Arrow K or L button to point to AUTO CLOCK CH”.
Then press the Arrow B or s but­ton until the channel number for your local PBS station appears.
If you do not know the PBS channel number, leave it set to [AUTO] which is located before [2]. The TV/DVD/VHS will search automatically all available channels for the local PBS station, and will select that channel.
– SETTING CLOCK –
AUTO CLOCK [ON] AUTO CLOCK CH [AUTO]
MANUAL CLOCK SET
B D.S.T. [OFF]
4 Exit the Auto Clock Setting
Press the SETUP button on the remote control to return to TV mode.
5 Turn off the TV/DVD/VHS
Turn the TV/DVD/VHS off. Because the Auto Clock functions automatically while the TV/DVD/VHS is off.
If you choose [AUTO],
the TV/DVD/VHS must search until the PBS chan-
nel is found. It must scan each channel for a couple of seconds to determine if that channel is transmit­ting the XDS signal.
if the time, that is automatically set by this selected
PBS station is incorrect, it may not be your local PBS station, but one from a different time zone. Or there is a case that no channel is broadcasting the XDS signal in your area, as shown by no time. In these cases, you must manually enter the correct local PBS station, or set the clock manually and turn off the Auto Clock Setting feature.
1 Select SETTING CLOCK
Press the SETUP button on the remote control.
Press the Arrow K or L button to point to SETTING CLOCK”.
Then, press the Arrow B button.
- TV/VCR SETUP -
TIMER PROGRAMMING
B SETTING CLOCK
CHANNEL SET UP USER’S SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] ZERO RETURN TIME SEARCH INDEX SEARCH
- 17 - EN
1F12
MANUAL CLOCK SETTING
Make sure ...
TV/DVD/VHS power must be turned on.
In the example below, the clock is to be set to:
DATE May 1st, 2001 SETTING TIME 5:40PM
1 Select SETTING CLOCK
Press the SETUP button on the remote control.
Press the Arrow K or L button to point to SETTING CLOCK”.
Then, press the Arrow B button.
2 Select MANUAL CLOCK
SET
Press the Arrow K or L button to point to MANUAL CLOCK SET”.
Then, press the Arrow B button.
3 Select the month
Press the Arrow K or L button until your desired month appears. (Example: May 05)
Then, press the Arrow B button.
4 Select the day
Press the Arrow K or L button until your desired day appears. (Example: 1st 01)
Then, press the Arrow B button.
5 Select the year
Press the Arrow K or L button until your desired year appears. (Example: 2001)
Then, press the Arrow B button.
- TV/VCR SETUP -
TIMER PROGRAMMING
B SETTING CLOCK
CHANNEL SET UP USER’S SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] ZERO RETURN TIME SEARCH INDEX SEARCH
– SETTING CLOCK –
AUTO CLOCK [ON] AUTO CLOCK CH [AUTO]
B MANUAL CLOCK SET
D.S.T. [OFF]
– MANUAL CLOCK SET –
MONTH DAY YEAR
0 5 / – – – – – – – – –
HOUR MINUTE
– – : – – – –
– MANUAL CLOCK SET –
MONTH DAY YEAR
0 5 / 0 1 – – – – – – –
HOUR MINUTE
– – : – – – –
– MANUAL CLOCK SET –
MONTH DAY YEAR
0 5 / 0 1 TUE 2 0 0 1
HOUR MINUTE
– – : – – – –
6 Select the hour
Press the Arrow K or L button until your desired hour appears. (Example: 5, PM)
Then, press the Arrow B button.
7 Select the minute
Press the Arrow K or L button until the desired minute appears. (Example: 40)
8 Start the clock
Press the SETUP button on the
– MANUAL CLOCK SET –
MONTH DAY YEAR
0 5 / 0 1 TUE 2 0 0 1
HOUR MINUTE
0 5 : – – PM
– MANUAL CLOCK SET –
MONTH DAY YEAR
0 5 / 0 1 TUE 2 0 0 1
HOUR MINUTE
0 5 : 4 0 PM
5:40 PM
remote control. Although seconds are not displayed,
they begin counting from 00 when you press the SETUP button on the remote control. Use this feature to synchronize the clock with the correct time.
NOTE:
When unplugging the AC cord or if there is a power failure for more than 30 seconds, you may have to reset the clock.
TO CHANGE CLOCK SETTING
If you want to change the clock,
1)Follow steps [1] and [2].
2)Select where you want to change using the Arrow B or s button.
3)Enter correct numbers using the Arrow K or L button.
4)Press the SETUP button on the remote control to start the clock.
PLEASE NOTE:
If there is no local PBS station in your area or on your cable system, select AUTO CLOCK and press the Arrow B or s button to turn [OFF] this function. Then you can manually adjust the clock.
- 18 - EN
1F12
TV OPERATION
WA TCHING ATV PROGRAM
1 Turn on the TV/DVD/VHS
Press the POWER button to turn on the TV/DVD/VHS.
2 Select the channel number
Press the CHANNEL K or L button to select your desired channel number or press the number buttons on the remote control.
Remember: If the TV/DVD/VHS is connected to a cable box or satellite box, the TV/DVD/VHS must be on CH3 or CH4, then the channel to be viewed must be selected on the cable box or satellite box.
3 Adjust sound
Press the VOLUME XXor YYbutton to adjust the volume.
VOLUME 20
C C C C C C C C C C C C
DEGAUSSING
Magnetism from nearby appliances might affect the color of the TV picture.
If this happens, move this unit away from the appli­ance. If the color is still not correct, disconnect power cord from AC outlet then reconnect it after 30 minutes.
PICTURE CONTROL
The TV/DVD/VHSs picture controls BRIGHT, CONTRAST, COLOR, TINT and SHARPNESS –
are preset to factory specifications. Although they are usually the best, you may need to make some further adjustments for a natural looking image.
NOTES:
Procedures must be followed within 5 seconds or
the Picture Control mode will be cancelled. When setting the Picture Control, the Game mode
will be cancelled.
Make sure ...
TV/DVD/VHS power must be turned on.
1 Select PICTURE CONTROL
Press the PICTURE button on the remote control.
2 Select item you want to adjust
Press the Arrow K or L button until desired control is displayed.
BRIGHT CONTRAST COLOR TINT SHARPNESS
BRIGHT
PP PP PP PP PP PP PP CC PP PP PP PP PP PP PP
+
3 Adjust the picture control
Press the Arrow B or s button to adjust to your desired level.
Arrow s Arrow B
BRIGHT to decrease to increase
brightness brightness
CONTRAST to decrease to increase
contrast contrast
COLOR to pale to brilliant TINT to purple to green
SHARPNESS to soft to clear
If there is a power failure of any kind, the unit will
retain its memory for this feature.
- 19 - EN
1F12
CLOSED CAPTION SYSTEM
You can view specially labeled (cc) TV programs, movies, news, pre-recorded tapes with either a dia­logue caption or text display.
CAPTION mode: By choosing the caption mode, you
can watch dramas, movies and news while captioning the dialogues and the contents of news.
TEXT mode: By choosing the text mode, you can
watch half screen text information if you want.
1-2: You may get these captions or text information
by selecting either “1” or “2”. Caption “2” is used, usually for a second language if available.
1 Select CAPTION
Press the SETUP button on the remote control.
Press the Arrow K or L button to point to CAPTION”.
2 Select your desired caption menu
Press the Arrow B or s button until your desired caption menu appears.
([CAPTION1], [CAPTION2], [TEXT1] or [TEXT2])
- TV/VCR SETUP -
TIMER PROGRAMMING SETTING CLOCK CHANNEL SET UP USER’S SET UP V-CHIP SET UP LANGUAGE [ENGLISH]
B CAPTION [OFF]
ZERO RETURN TIME SEARCH INDEX SEARCH
- TV/VCR SETUP -
TIMER PROGRAMMING SETTING CLOCKB CHANNEL SET UP USER’S SET UP V-CHIP SET UP LANGUAGE [ENGLISH]
B CAPTION [CAPTION1]
ZERO RETURN TIME SEARCH INDEX SEARCH
NOTE:
Not all programs are broadcast with closed captions. Your television is designed to provide error free closed captions from high quality antenna, cable and VCR signals. Conversely, poor quality signals are likely to result in caption errors or no captions at all. Common signal conditions which may cause captions errors are listed below:
Automobile ignition noise
Electric motor brush noise
Weak snowy reception on TV screen
Multiplex signal reception displaying picture
ghosts or airplane flutter. Playback of poorly recorded or worn VCR tapes.
NOTE:
If the TV/DVD/VHS displays a black box on the TV screen, this means that the TV/DVD/VHS is set to the TEXT mode. To clear screen, select [CAPTION1], [CAPTION2] or [OFF].
Make sure ...
TV/DVD/VHS power must be turned on.
3 Exit the caption setting mode
Press the SETUP button on the remote control to return to TV mode.
TO CANCEL THE CLOSED CAPTION SYSTEM
Repeat steps [1] and [2], select [OFF] using the Arrow B or s button. Press the SETUP button on the remote control to return to TV mode.
WHEN THE CLOSED CAPTION MODE IS ON
The On-Screen Display will disappear after 5 sec­onds.
This is also true when the MUTE button is pressed,
and when the PAUSE button is pressed while recording.
If there is a power failure of any kind, the unit will
retain its memory for this feature.
- 20 - EN
1F12
Loading...
+ 44 hidden pages