Sylvania SRDV495 User Manual

• Remote control (NB118UD) with two AA batteries

• RF cable (

WPZ

0901TM002)• Audio/Video cables

(WPZ0102TM015 or WPZ0102LT E01)

If you need additional operating assistance after reading this owner’s manual,

please call

TOLL FREE : 1-800-968-3429

Before you use this unit, you need to complete connections. Refer to “Connections” on pages 10-12.

To r ecord a program easily, refer to “Easy DVD recording” on pages

54-55

after connections are completed.

(You CANNOT copy any copyright protected DVD disc with this unit.)

SRDV495

INSTRUCCIONES EN ESPAÑOL INCLUIDAS.

Owner’s Manual

DVD Recorder with Video Cassette Recorder

Supplied Accessory

• Owner’s Manual (1VMN20233)• Quick Use Guide (1VMN20319)• DVD-R Blank Media (3 discs)

Owner's Manual

CHANNEL

OUTPUT SELECT

VCR DVD

DVD RECORD

DVD-RW/-R

VCR RECORD

S-VIDEO VIDEO L - AUDIO - R

OPEN/CLOSE

PLAYREWPOWER F.FWD STOP/EJECT

STOP PLAY

ONE TOUCH

DUBBING

Changing the SETUP menu

Playing discs VCR functions

Before you start

Connections Getting started

Recording Editing Others

Español

Precautions

Before you start

Laser Safety

This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury.

CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN

MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO NOT STARE INTO BEAM. LOCATION: INSIDE, NEAR THE DECK MECHANISM.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

CAUTION

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

RADIO-TV INTERFERENCE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses,and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment and receiver.

3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4) Consult the dealer or an experienced radio/TV technician for help.

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-

003 du Canada.

FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications to

this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual.The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

CAUTION:TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY

INSERT.

ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA

FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

A NOTE ABOUT RECYCLING

This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations.

Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.

For Customer Use: Read carefully the information located at the back of this unit and enter below the Serial No. Retain this information for future reference.

Model No.

_____________________

Serial No. _____________________

Make your contribution to the environment!!!

• Used up batteries do not belong in the dust bin.

• You can dispose of them at a collection point for used up batteries or special waste. Contact your council for details.

Before you start

Español

Changing the SETUP menu

Playing discs

VCR functionsConnections

Getting started

Recording Editing

Others

Before you start

Important Safeguards

1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated.

2. Retain Instructions- The safety and operating instructions should be retained for future reference.

3. Heed Warnings - All warnings on the appliance and in the operating instructions should be adhered to.

4. Follow Instructions - All operating and use instructions should be followed.

5. Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. EXCEPTION:A product that is meant for uninterrupted service and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the appliance in the cleaning description otherwise required in item

6. Attachments - Do not use attachments not recommended by

the product manufacturer as they may cause hazards.

7. Water and Moisture- Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.

8. Accessories - Do not place this product on an unstable cart, stand, tripod, bracket, or table.The product may fall, causing serious injury to a child or adult, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the appliance should follow the manufacturer's instructions and should use a mounting accessory recommended by the manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

9.Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating,and these openings must not be blocked or covered.The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to.

10. Power Sources - This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

11. Grounding or Polarization - This product is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way.This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

12. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

13. Outdoor Antenna Grounding - If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges.Article

810 of

the National Electrical Code,ANSI/NFPA No.

70,provides infor-

mation with regard to proper grounding of the mast and sup-

porting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. (Fig. A)

14. Lightning - For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

15. Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

16. Overloading - Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

17. Object and Liquid Entry - Never push objects of any kind into this product through any openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

18. Servicing - Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

19. Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a.When the power-supply cord or plug is damaged. b. If liquid has been spilled,or objects have fallen into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by following the oper-

ating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.

e. If the product has been dropped or damaged in any way. f.When the product exhibits a distinct change in performance this

indicates a need for service.

20. Replacement Parts - When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

21. Safety Check - Upon completion of any service or repairs to this product,ask the service technician to perform safety checks to determine that the product is in proper operating condition.

22. Heat - This product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

Precautions (cont’d)

FIGURE A

EXAMPLE OF ANTENNA GROUNDING

AS PER NATIONAL ELECTRICAL CODE

GROUND CLAMP

ELECTRIC SERVICE EQUIPMENT

NEC – NATIONAL ELECTRICAL CODE

S2898A

ANTENNA LEAD WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMP

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

Precautions (cont’d)

Before you start

Installation Location

For safety and optimum performance of this unit:

• Install the unit in a horizontal and stable position. Do not place anything directly on top of the unit. Do not place the unit directly on top of the TV.

• Shield it from direct sunlight and keep it away from sources of intense heat. Avoid dusty or humid places. Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes on the sides of the unit. Avoid locations subject to strong vibration or strong magnetic fields.

Avoid the Hazards of Electrical Shock and Fire

• Do not handle the power cord with wet hands.

• Do not pull on the power cord when disconnecting it from AC wall outlet. Grasp it by the plug.

• If by accident water is spilled on this unit, unplug the power cord immediately and take the unit to our Authorized Service Center for servicing.

• Do not put your fingers or objects into the unit cassette holder.

Moisture Condensation Warning

Moisture condensation may occur inside the unit when it is moved from a cold place to a warm place, or after heating a cold room or under conditions of high humidity. Do not use this unit at least for 2 hours.

About Copyright

Unauthorized copying, broadcasting, public performance and lending of discs are prohibited. This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

Notice for progressive scan output

Consumers should note that not all high definition television sets are fully compatible with this product and may cause artifacts to be displayed in the picture. In case of progressive scan picture problems, it is recommended that the user switch the connection to the interlaced video output.

Symbol in this owner's manual

Many functions of this unit are depending on the disc type or the recording mode. To specify for what disc type or recording mode each function is, we put the following symbols at the beginning of each item to operate.

Maintenance

SERVICING

• Please refer to relevant topics on the Troubleshooting Guide on pages

98-100 before returning the product.

• When this unit becomes inoperative, do not try to correct the problem by yourself.There are no user-serviceable parts inside.Turn off, unplug the power plug, and please call our help line mentioned on the front page to locate an Authorized Service Center.

CLEANING THE CABINET

• Use a soft cloth slightly moistened with a mild detergent solution. Do not use a solution containing alcohol, spirits, ammonia or abrasive.

CLEANING DISCS

• When a disc becomes dirty, clean it with a cleaning cloth.Wipe the disc from the center out. Do not wipe in a circular motion.

• Do not use solvents such as benzine, thinner, commercially available cleaners, detergent, abrasive cleaning agents or antistatic spray intended for analogue records.

CLEANING THE DISC LENS

•

If this unit still does not perform properly although you refer to the relevant sections and to “TROUBLESHOOTING GUIDE” in this Owner’s Manual, the laser optical pickup unit may be dirty. Consult your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup unit.

DISC HANDLING

• Handle the discs so that fingerprints and dust do not adhere to the surfaces of the discs.

•

Always store the disc in its protective case when it is not used.

AUTO HEAD CLEANING

• Automatically cleans video heads as you insert or remove a cassette, so you can see a clearer picture.

• Playback picture may become blurred or interrupted while the TV program reception is clear. Dirt accumulated on the video heads after a long period of use, or the usage of rental or worn tapes can cause this problem. If a streaky or snowy picture appears during playback, the video heads in the unit may need to be cleaned.

1. Please visit your local electronics retailer and purchase

a good quality VHS Video Head Cleaner.

2. If a Video Head Cleaner does not solve the problem,

please call our help line mentioned on the front page to locate an Authorized Service Center.

NOTES:

• Remember to read the instructions provided with the video head cleaner before use.

• Clean video heads only when problems occur.

Symbol

DVD-V

DVD-RW

DVD-R

MP3

VCR

First: (Press:)

Video

Description

Available to DVD Video discs

Available to DVD-RW in Video mode

Available to DVD-RW in VR mode

Available to DVD-R discs

Available to Audio CDs

Available to CD-R/RW discs with MP3 files

Available to VHS tapes Use only cassettes marked with this unit.

Indicates that you need to select the DVD

DVD

mode by pressing DVD button on the remote control before proceeding next step.

Indicates that you need to select the VCR

VCR

mode by pressing VCR button on the remote control before proceeding next step.

Before you start

Changing the SETUP menu

Playing discs

VCR functionsBefore you start Connections

Getting started

Recording Editing

Others Español

Features

Recording

This unit is compatible with both DVD-RW, which is rewritable, and DVD-R, which is available for recording once. Also, this unit allows you to record to the video cassette tape. You can choose either one for your convenience.

Up to 8 programs recording:

You can program the unit to record up to 8 programs, up to a year in advance. Daily or weekly program recordings are also available.

One-touch timer recording:

You can easily set a recording time as you prefer. Every time the REC/OTR button on the remote control or the RECORD button on the front panel pressed during recording, the recording time will be increased by 30 minutes up to 8 hours.The recording automatically stops when the recording time you set is reached.

Dubbing mode:

You can copy a DVD disc to a videotape or copy a videotape to a DVD disc.This function will be possible only if the DVD disc and the videotape are not copy protected.

REC MONITOR:

You can confirm the picture quality for recording which you set. If you want to change the recording speed, press REC SPEED button to set the desired recording mode.

Automatic Chapter marker setting:

Chapter markers will be put on recordings as you set in SETUP menu before attempting to record.

Automatic Title menu making:

The unit makes title menus automatically when finalizing the disc which are recorded in Video mode.

Automatic PLAYLIST making (VR mode):

A Playlist will be prepared from an Original list, so that you can edit titles in a Playlist as you prefer. An Original list is kept as it is.

Play

Theater surround sound in your home:

When connecting the unit to an amplifier or a decoder which is compatible with Dolby Digital or DTS, you are able to experience the theater surround sound from discs which contain tracks recorded in Dolby Digital format.

Quick search for what you want to watch:

You can easily find the part you want to watch using the search function. Search for a desired point on a disc by title, chapter or time.

Start to play from Original and Playlist (VR mode):

Title playing is available from either an Original list or Playlist.

Quick search for what you want to watch:

You can easily find the part you want to watch using the Index search/Time search functions. An index mark will be assigned at the beginning of each recordings you make. For Time search function, you can go to a specific point on a tape by entering the exact amount of time you wish to skip.

VCR mode

DVD mode

VCR modeDVD mode

Editing

Setting/Clearing chapter markers:

You can easily add chapter markers anywhere in your recordings for easy editing. (VR mode)

Making your own Playlist:

With the original remaing as it is, you can edit titles on various playlist as you prefer. Putting names on titles. Setting pictures for thumbnails. Setting/clearing chapter markers. Deleting parts of titles, etc.

Protecting titles:

To avoid editing or erasing titles, the protect function is useful when it is ON in the original list.

Compatibility

Available for playing discs recorded in Video mode on a regular DVD player (Video mode):

Discs recorded in the Video mode can be played on regular DVD players, including computer DVD drives compatible with DVD-Video playback*.

* DVD-Video Format (Video mode) is a new format for recording on DVD-R/RW discs that was approved by the DVD Forum in 2000. Adoption of this format is optional for manufactures of DVD playback devices and there are DVD-Video players, DVD-ROM drives or other DVD playback devices that do not play DVD-R/RW discs recorded in the DVD-Video Format.

Others

Progressive Scan system

Unlike conventional interlace scanning, the progressive scan system provides less flickering and a smoother appearance without visible scan lines.

DVD mode

This unit not only plays DVD’s, CDs and VHS tapes but also offers features for you to record to DVD discs and edit them.The following features are offered with this unit.

Manufactured under license from Dolby Laboratories.“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

Note:

You will need to finalize the discs recorded in Video mode to play in other DVD players.

Note:

You will need to finalize the discs recorded in Video mode to play in other DVD players.

“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.

Ta b le of contents

Before you start

VCR functions . . . . . . . . . . . . . . . . . . .50

Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Recording and One-touch timer recording . . . .50

Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

One-touch timer recording . . . . . . . . . . . . . . . . . . . .51

Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Index search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Time search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

Other operations . . . . . . . . . . . . . . . . . . . . . . . .53

Recording . . . . . . . . . . . . . . . . . . . . . . .54

Easy DVD recording . . . . . . . . . . . . . . . . . . . . . .54

Information on DVD recording . . . . . . . . . . . . . .56

Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

Recording speed . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

Restrictions on recording . . . . . . . . . . . . . . . . . . . . .56

Information on copy control . . . . . . . . . . . . . . . . . . .57

Making discs playable in other DVD player (Finalize) 57

Formatting a disc . . . . . . . . . . . . . . . . . . . . . . . .58

Choosing the recording format of a blank disc . . . . .58

Reformatting a disc . . . . . . . . . . . . . . . . . . . . . . . . . .60

Basic recording . . . . . . . . . . . . . . . . . . . . . . . . . .61

Checking the recording picture quality . . . . . . . . . . .62

One-touch timer recording . . . . . . . . . . . . . . . .63

Timer recording . . . . . . . . . . . . . . . . . . . . . . . . .64

Hints for timer recording . . . . . . . . . . . . . . . . . . . . .66

Settings for an external source . . . . . . . . . . . . . .67

Connection to an external source . . . . . . . . . . . . . .67

Recording from an external source . . . . . . . . . . . . . .68

Dubbing Mode . . . . . . . . . . . . . . . . . . . . . . . . . . .69

Finalizing the discs . . . . . . . . . . . . . . . . . . . . . . .71

Setting a disc to protect . . . . . . . . . . . . . . . . . . .72

Editing . . . . . . . . . . . . . . . . . . . . . . . . .73

Information on disc editing . . . . . . . . . . . . . . . . .73

Guide to a title list . . . . . . . . . . . . . . . . . . . . . . . . . .73

Editing discs in Video mode . . . . . . . . . . . . . . . . . . . .73

Editing discs in VR mode . . . . . . . . . . . . . . . . . . . . . .74

Editing DVD-RW discs in Video mode . . . . . . . .75

Deleting titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75

Putting names on titles . . . . . . . . . . . . . . . . . . . . . . .76

Setting or clearing chapter markers . . . . . . . . . . . . .77

Editing DVD-RW discs in VR mode (Original) . .78

Deleting titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78

Deleting parts of titles . . . . . . . . . . . . . . . . . . . . . . .79

Naming Titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80

Setting or clearing chapter markers . . . . . . . . . . . . .82

Setting pictures for thumbnails . . . . . . . . . . . . . . . . .83

Title Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85

Releasing titles from protection . . . . . . . . . . . . . . . .86

Editing DVD-RW discs in VR mode (Playlist) . . .87

Deleting titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87

Deleting parts of titles . . . . . . . . . . . . . . . . . . . . . . .88

Naming Titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89

Setting or clearing chapter markers . . . . . . . . . . . . .91

Setting pictures for thumbnails . . . . . . . . . . . . . . . . .92

Adding titles to a Playlist . . . . . . . . . . . . . . . . . . . . . .94

Deleting a Playlist . . . . . . . . . . . . . . . . . . . . . . . . . . .95

Editing DVD-R discs . . . . . . . . . . . . . . . . . . . . . .96

Deleting titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96

Naming Titles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97

Others . . . . . . . . . . . . . . . . . . . . . . . . .98

Tr oubleshooting . . . . . . . . . . . . . . . . . . . . . . . . .98

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .103

Language code . . . . . . . . . . . . . . . . . . . . . . . . .103

Español . . . . . . . . . . . . . . . . . . . . . . . .104

Before you start . . . . . . . . . . . . . . . . . . .2

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Ta b le of contents . . . . . . . . . . . . . . . . . . . . . . . . . .6

Functional overview . . . . . . . . . . . . . . . . . . . . . . .7

Installing batteries in the remote control . . . . . . . . . .9

Using a remote control . . . . . . . . . . . . . . . . . . . . . . . .9

VCR/DVD recorder Switching . . . . . . . . . . . . . . . . . .9

Connections . . . . . . . . . . . . . . . . . . . . .10

Connection to a TV . . . . . . . . . . . . . . . . . . . . . . .10

Connection to a cable box or satellite box . . . .11

Connection to an Audio System . . . . . . . . . . . . .12

Getting started . . . . . . . . . . . . . . . . . . .13

Functional overview . . . . . . . . . . . . . . . . . . . . . .13

SETUP/DISC/CD menu . . . . . . . . . . . . . . . . . . . . . . .13

DISPLAY menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Channel settings . . . . . . . . . . . . . . . . . . . . . . . . .16

Presetting channels automatically . . . . . . . . . . . . . . .16

Adding/deleting channels . . . . . . . . . . . . . . . . . . . . . .17

Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . .18

Auto Clock Setting . . . . . . . . . . . . . . . . . . . . . . . . . .18

Manual Clock Setting . . . . . . . . . . . . . . . . . . . . . . . .19

Setting the daylight saving time . . . . . . . . . . . . . . . . .21

Selecting the TV aspect ratio . . . . . . . . . . . . . . .22

Selecting TV stereo or SAP . . . . . . . . . . . . . . . .23

RF converter output . . . . . . . . . . . . . . . . . . . . . .24

Changing the SETUP menu . . . . . . . . .25

Tour of the SETUP menu . . . . . . . . . . . . . . . . . .25

Language settings . . . . . . . . . . . . . . . . . . . . . . . .26

Display settings . . . . . . . . . . . . . . . . . . . . . . . . . .28

Audio settings . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Parental control settings . . . . . . . . . . . . . . . . . . .32

Playing discs . . . . . . . . . . . . . . . . . . . . .34

Information on DVD play . . . . . . . . . . . . . . . . . .34

Guide to displays . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Basic playback . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Playing discs using the disc menu . . . . . . . . . . . . . . .37

Playing discs using the title menu . . . . . . . . . . . . . . .38

Special playback . . . . . . . . . . . . . . . . . . . . . . . . .39

Resume play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Fast forward / Fast reverse . . . . . . . . . . . . . . . . . . . .39

Skipping TV commercials during play . . . . . . . . . . . . .40

Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Step by step playback . . . . . . . . . . . . . . . . . . . . . . . .41

Slow forward / Slow reverse play . . . . . . . . . . . . . . .41

Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Marker Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Title/Chapter search . . . . . . . . . . . . . . . . . . . . . . . . .43

Track search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Time search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Repeat/Random/Program play . . . . . . . . . . . . . .45

Repeat play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Random play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Program play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Selecting audio and video formats . . . . . . . . . . .47

Switching audio soundtrack . . . . . . . . . . . . . . . . . . . .47

Switching subtitles . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Switching camera angles . . . . . . . . . . . . . . . . . . . . . .49

Reducing block noise . . . . . . . . . . . . . . . . . . . . . . . .49

Functional overview

Before you start

Changing the SETUP menu

Playing discs

VCR functionsBefore you start Connections

Getting started

Recording Editing

Others Español

Front Panel

ONE TOUCH

DUBBING

CHANNEL

VCR RECORD DVD RECORD

DVD -RW/-R

OPEN/CLOSE

PLAYREWPOWER F.FWD STOP/EJECT

OUTPUT SELECT

VCR DVD

STOP PLAY

S-VIDEO VIDEO L - AUDIO - R

222120

17 1215 14 910

534

16 13 8 7 6

1.POWER button / indicator (DVD/VCR)

Press to turn the unit on and off. If timer programmings have been set, press to set the unit in timer-standby mode. Press to cancel the timer standby mode and turn the unit on. The light besides the POWER button lights up when power is on.

2. Cassette compartment (VCR)

Insert a tape here.

3. A OPEN/CLOSE button (DVD)

Press to open or close the disc tray.

4. OUTPUT SELECT button (DVD/VCR)

Press to select the component you wish to operate.

5.Disc tray (DVD)

Place a disc on the disc tray when it’s open.

6.AUDIO input jacks (LINE2) (DVD/VCR)

Use to connect external equipment with standard audio cables.

7. VIDEO input jack (LINE2) (DVD/VCR)

Use to connect external equipment with a standard video cable.

8. S-VIDEO input jack (LINE2) (DVD only)

Use to connect the S-Video output of external equipment with an S-Video cable (not supplied).

9.DVD RECORD button (DVD)

Press once to start recording. Press repeatedly to set the time for One-Touch Recording.

10. PLAY button (DVD)

Press to start or resume play.

11.STOP button (DVD)

Press to stop playback or recording. Press to cancel the proceeding timer recording in DVD.

12.DVD SELECT indicator

This indicator lights up when the DVD output mode is selected.

13. VCR SELECT indicator

This indicator lights up when the VCR output mode is selected.

14. ONE TOUCH DUBBING button (DVD/VCR)

Press to start VCR to DVD or DVD to VCR duplication you set in the SETUP menu.

15. CHANNEL L / K button (DVD/VCR)

Press to change the channel up and down.

16. Display (DVD/VCR)

Refer to “Front Panel Display Guide” on page 15.

17. Remote control sensor (DVD/VCR)

Receive signals from your remote control so that you can control the unit from a distance.

18. VCR RECORD button (VCR)

Press once to start a recording. Press repeatedly to set the time for One-Touch Recording.

19. PLAY button (VCR)

Press to start playback.

20.STOP/EJECT button (VCR) EJECTbutton-

Press to remove the tape from the unit.

STOP button-Press to stop the tape playback. Press to cancel the proceeding timer recording in VCR.

21.F.FWD button (VCR)

Press to rapidly advance the tape, or view the picture rapidly in forward during playback. (Forward Search)

22. REW button (VCR)

Press to rewind the tape, or to view the picture rapidly in reverse during playback mode. (Rewind Search)

Rear Panel

DVD DVD/VCR

ANTENNA

AUDIO OUTAUDIO IN

S-VIDEO

AUDIO

OUT

DIGITAL

AUDIO OUT

COAXIAL

COMPONENT VIDEO OUT

VIDEO OUTVIDEO IN

OUT

634521

1112

1.AC Power Cord (DVD/VCR)

Connect to a standard AC outlet to supply power to this unit.

2.S-VIDEO IN jack (LINE1)

(DVD only)

Use to connect the S-Video output of external equipment with an S-Video cable (not supplied).

COMPONENT VIDEO OUT jacks (DVD only)

Use to connect a TV monitor with component video inputs with component video cables (not supplied).

4.AUDIO IN jacks (LINE1) (DVD/VCR)

Use to connect external equipment with standard audio cables.

5.AUDIO OUT jacks (DVD/VCR)

Use to connect a TV monitor, AV receiver or other equipment with standard audio cables.

6. ANTENNA IN jack (DVD/VCR)

Use to connect an antenna.

7. ANTENNA OUT jack (DVD/VCR)

Use to connect an antenna cable to pass the signal from the ANTENNA IN to your TV monitor.

8. VIDEO OUT jack (DVD/VCR)

Use to connect a TV monitor, AV receiver or other equipment with a standard video cable.

9.VIDEO IN jack (LINE1) (DVD/VCR)

Use to connect external equipment with a standard video cable.

10. S-VIDEO OUT jack (DVD only)

Use to connect the S-Video input of a TV monitor, AV receiver or other equipment with an S-Video cable (not supplied).

11.AUDIO OUT jacks (DVD only)

Use to connect a TV monitor, AV receiver or other equipment with standard audio cables.

12.COAXIAL DIGITAL AUDIO OUT jack (DVD only)

Use to connect an AV receiver, Dolby Digital decoder, DTS decoder or other equipment with a coaxial digital input jack with a digital coaxial cable (not supplied).

Note: Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause perma-

nent damage to the unit.

•

These jacks are useful only in DVD mode.

Functional overview (cont’d)

Before you start

SETUP button (DVD/VCR)

Press to display the setup menu. During DVD playback, press and hold for more than 3 seconds to switch to the progressive video output or the interlaced.

REC MONITOR button (DVD)

Press to check the recording speed before attempting a recording.

MENU/LIST button (DVD)

Press to display the Disc menu. To change ORIGINAL and PLAYLIST on the TV screen. (VR mode only)

10.

TOP MENU button (DVD)

Press to display the top menu.

11. CLEAR/C.RESET button (DVD/VCR)

• DVD mode Press to clear the password once entered, to cancel the programming for CD, to clear the selected marker number in the marker setup mode or to clear the program once entered in the timer recording setting mode,etc.

• VCR mode Press to reset the tape counter.

12.

SEARCH MODE button (VCR)

To call up the index or time search menu.

13. CM SKIP button (DVD)

During playback, press to advance 30 seconds.

14. REC SPEED button (DVD/VCR)

Press to select the recording speed.

15.

OPEN/CLOSE A button (DVD)

Press to open or close the disc tray.

16.AUDIO button (VCR)

During playback of a HiFi video tape, press to change the AUDIO OUT setting to “HIFI” or “MONO”.

17.

CH K / L buttons (DVD/VCR)

• DVD mode Press to change the channel up and down.

• VCR mode Press to change the channel up and down. Press to adjust tape tracking during playback or in slow motion. In still mode, you can adjust the picture if blurred vertically.

18.

VIDEO/TV button (DVD/VCR)

Press to select VIDEO or TV mode.

POWER button (DVD/VCR)

Press to turn the unit on and off. If timer programmings have been set, press to set the unit in timer-standby mode. Press to cancel the timer standby mode, then turn the unit on.

Number buttons (DVD/VCR)

Press to select channel numbers. Press to select a title/chapter/track on display or a TV channel. Also press to enter values for the settings in the SETUP menu.

DISPLAY button (DVD/VCR)

Press to display or change the on-screen display.

4. VCR button

Press to allow the remote control to operate the VCR. Refer to page 9. Press to select the VCR output mode.

5. E button (DVD/VCR)

• DVD mode During playback, press to play fast reverse or during pause, press to play slow reverse.

• VCR mode Press to rewind the tape or to view the picture rapidly in reverse during playback mode.

REC/OTR button (DVD/VCR)

Press once to start a recording. Press repeatedly to set the time for One-Touch Recording.

19. SLOW button (VCR)

During playback, press to view the video tape in slow motion.

20.PAUSE F button (DVD/VCR)

Press to pause play or recording.

21.DVD button

Press to allow the remote control to operate the DVD. Refer to page 9. Press to select the DVD output mode.

22. PLAY B button (DVD/VCR)

Press to start or resume play.

23. D button (DVD/VCR)

• DVD mode During playback, press to play fast forward. Or when playback is paused, press to play slow forward.

• VCR mode Press to rapidly advance the tape or view the picture rapidly in forward during playback.

24.STOP C button (DVD/VCR)

Press to stop playback or recording.

25. TIMER PROG. button (DVD/VCR)

Press to display the timer program setting menu.

26. ENTER button (DVD/VCR)

Press to confirm or select menu items.

27. K / L / { / B buttons (DVD/VCR)

Press to select items or settings.

28.RETURN button (DVD/VCR)

Press to return to the previously displayed menu screen.

29. ZOOM button (DVD)

During playback, press to enlarge the picture on the screen.

30. SKIP H button (DVD)

During playback, press to skip to the previous chapter or track. Or during playback, press to play reverse step by step.

SKIP G button (DVD)

During playback, press to skip to the next chapter or track. Or during playback, press to play forward step by step.

31. ONE TOUCH DUBBING button (DVD/VCR)

Press to start VCR to DVD or DVD to VCR duplication however you set in the SETUP menu.

Remote Control

POWER

REC SPEED

.@/:

123

GHI JKL MNO

456

PQRS

7809

DISPLAY

REC/OTR

REC MONITOR

MENU/LIST

CLEAR/C.RESET

MODE

OPEN/CLOSE

AUDIO

ABC DEF

TUV WXYZ

SPACE

VCR

DVD

PLAY

STOP

SETUP

TIMER PROG.

ENTER

TOP MENU

ZOOM SKIP SKIP

ONE TOUCH

CM SKIP

VIDEO/TV

SLOW

PAUSE

RETURN

DUBBING

28 29

30 31

Functional overview (cont’d)

Before you start

Changing the SETUP menu

Playing discs

VCR functionsBefore you start Connections

Getting started

Recording Editing

Others Español

Using a remote control

Keep in mind the following when using the remote control:

• Make sure that there is no obstacle between the remote control and the remote sensor on the unit.

• Use within the operating range and angle as shown.

• Remote operation may become unreliable if strong sunlight or fluorescent light is shining on the remote sensor of the unit.

• Remote control for different devices can interfere with each other. Avoid using remote control for other equipment located close to the unit.

• Replace the batteries when you notice a fall off in the operating range of the remote control.

S K I P

R E C

P A U S

E N T

E R

M E N

L A Y L I S

T O P M E

N U /

R I G IN A

F W D

S T O

L A Y

R E

Installing batteries in the remote control

Install two AA batteries (supplied) matching the polarity indicated inside battery compartment of the remote control.

Note:

Incorrect use of batteries can result in hazards such as leakage and bursting. Please observe the following:

• Do not mix new and old batteries together.

• Do not use different kinds of batteries together, although they may look similar, different batteries may have different voltages.

• Make sure that the plus and minus ends of each battery match the indications in the battery compartment.

•Remove batteries from equipment that is not going to be used for a month or more.

• When disposing of used batteries, please comply with governmental regulations or environmental public instruction rules that apply in your country or area.

• Do not recharge, short-circuit, heat, burn or disassemble batteries.

Because this product is a combination of a VCR and a DVD recorder, you must select first which component you wish to operate with the OUTPUT SELECT button.

VCR DVD

OUTPUT SELECT

OUTPUT SELECT button

DVD SELECT indicator

VCR SELECT indicator

POWER

REC SPEED

AUDIO

ZOOM SKIP SKIP

OPEN/CLOSE

TOP MENU

SPACE

VCR

SETUP

CM SKIP

TIMER PROG.

RETURN

123

456

7809

STOP

PLAY

VIDEO/TV

SLOW

PAUSE

.@/:

ABC DEF

GHI JKL MNO

PQRS

REC/OTR

REC MONITOR

MENU/LIST

CLEAR/C.RESET

MODE

ENTER

DISPLAY

TUV WXYZ

DVD

DVD button

VCR button

ONE TOUCH DUBBING

CHANNEL

VCR RECORD DVD RECORD

DVD -RW/-R

OPEN/CLOSE

PLAYREWPOWER F.FWD STOP/EJECT

OUTPUT SELECT

VCR DVD

STOP PLAY

S-VIDEO VIDEO L - AUDIO - R

ONE TOUCH

DUBBING

Press the VCR button on the remote control.

(Verify that the VCR SELECT indicator is lit.)

VCR MODE

Note

•

Pressing only the OUTPUT SELECT button on the front panel DOES NOT switch the mode of the remote control. You MUST select the correct mode on the remote control.

• Pressing the SETUP or the TIMER PROG. button

switches the unit to the DVD mode.

Press the DVD button on the remote control.

(Verify that the DVD SELECT indicator is lit.)

DVD MODE

VCR/DVD recorder Switching

Within about 23feet (7m)

Remote control

60˚

POW

RE W

F .F WD

ST OP

/E JEC

PL A Y

V CR

R EC

OR D

O P EN /C

L OSE

O NE T

OUC D U BBI

C H A

NN EL

S T

LAY

TPU

T S

EL EC

D V D

D V D R

EC O RD

DVD

-V

/-R

IDE

VI D EO

DI O

- R

Connection to a TV

Connections

DVD DVD/VCR

ANTENNA

AUDIO OUTAUDIO IN

S-VIDEO

AUDIO

OUT

DIGITAL

AUDIO OUT

COAXIAL

COMPONENT VIDEO OUT

VIDEO OUTVIDEO IN

OUT

(Back of TV)

Plug in the AC power cord of this unit.

Cable Signal

Connect

Disconnect

Antenna

(Back of this unit)

(Back of TV)

RF Cable (supplied)

Connect

Make one of the following connections, depending on the capabilities of your existing equipment.

DVD DVD/VCR

ANTENNAINAUDIO OUTAUDIO IN

S-VIDEO

AUDIO

OUTT

COMPONENT VIDEO OUT

VIDEO OUTVIDEO IN

OUT

DVD DVD/VCR

ANTENNAINAUDIO OUTAUDIO IN

S-VIDEO

AUDIO OUT

DIGITAL

AUDIO OUT

COAXIAL

COMPONENT VIDEO OUT

VIDEO OUTVIDEO IN

OUT

DVD

DVD/VCR

AUDIO OUT

DVD/VCR

VIDEO OUT

DVD

S-VIDEO

OUT

DVD

COMPONENT VIDEO OUT

AUDIO

OUT

AUDIO IN VIDEO IN

S-VIDEO IN

COMPONENT

VIDEO IN

AUDIO OUT

Audio Connection

Method 2 Method 3

Better picture Best picture

S-VIDEO OUT

COMPONENT VIDEO OUT *Required for progressive

scan display from DVD.

Audio cable

(supplied)

Component Video cables (not supplied)

This unit

Note

• Connect this unit directly to the TV. If the A/V cables are connected to a VCR, pictures may be distorted due to the copy protection system.

• Method 2 and method 3 are only useful in DVD mode.

Method 1

Good picture

VIDEO OUT

Video cable (supplied)

S-Video cable (not supplied)

•

These jacks are useful only in DVD mode.

If your TV is compatible with 480p progressive scanning and you want to enjo

y that high quality picture;

You must select the connection Method 3 above and select progressive scanning mode. To set the mode, press and hold the SETUP button on the remote control for more than 3 seconds during DVD playback, so that “P.SCAN” will appear on the display of this unit.

If your TV is not compatible with progressive scanning;

Press and hold the SETUP button on the remote control for more than 3 seconds during DVD playback, so that “P.SCAN” on the display of this unit will disappear.

TOP MENU

SETUP

TIMER PROG.

RETURN

STOP

PLAY

REC/OTR

REC MONITOR

MENU/LIST

ENTER

more than 3 seconds

during DVD playback

[Interlace mode]

[Progressive scanning mode]

Changing the SETUP menu

Playing discs VCR functions

Before you start

Connections Getting started

Recording Editing Others

Español

Connections

DVD/VCR

ANTENNA

OUT

RF Cable

(supplied)

(Back of this unit)

OUT

(Back of TV)

Cable

Signal

Connection A

(Cable box or

Satellite box)

Connection to a cable box or satellite box

Note to the Cable TV System Installer :

This reminder is provided to call the Cable TV system installer’s attention to Article 820-40 of the National Electrical Code, which provides guidelines for proper grounding - in particular, specifying that the cable ground shall be connected to the grounding system of the building, as close to the point of cable

entry as possible.

Select this connection when you want to view or record a scrambled channel. With this connection, channels cannot be changed on this unit.You can view or record ONLY the channels you have selected on the cable box or the satellite box.

• While you are recording, only the recorded channel can be viewed.

To select channels on the cable box or satellite box

1) Turn on this unit by pressing POWER button.The “POWER” indicator on the front panel will light up. Then, press the CHANNEL buttons to select channel 3 or 4 (the same channel as the output channel of the cable box or satellite box).

• If noise appears on the TV screen

,press VIDEO/TV button on the remote control.

• If you use channel 4,you need to change this unit’s RF output to channel 4. Refer to “RF converter out- put” on page 24.

2) On the TV, select channel 3 or 4 (the same channel as you have selected at step 1).

3) On the cable box or satellite box, select the channel you want to view or record.

DVD/VCR

ANTENNA

OUT

RF Cable (supplied)

RF Cable

(Back of TV)

OUT

(Cable box or

Satellite box)

Cable

Signal

Connection B

(Back of this unit)

Select this connection when you want to change channels on this unit.With this connection, you may watch one channel while recording another.

• You may not view or record a scrambled channel.

To select channels on the cable box or satellite box

1) On the cable box or satellite box, select channel 3 or 4 (the same channel as this unit’s RF output channel.)

• Refer to “RF converter output” on page 24.

2) On the TV, select the same channel as the output channel (3 or 4) of the cable box or satellite box.

3) Turn on this unit by pressing POWER button. The “POWER” indicator on the front panel will light up.

Then select the channel you want to view or record.

• If noise appears on the TV screen, press VIDEO/TV button on the remote control.

To playback a DVD disc or a tape

Before trying to playback DVD or tape you MUST follow step 1) to 2) above.

• Refer to “Playback” on pages 35-36, 50.

To view one channel while recording another

1) While you are recording on this unit, press VIDEO/TV button.

2) On the cable box or satellite box, select the channel you want to view.

Connections

Connection to an Audio System

• Before changing the connections, all devices should be turned off.

• Refer to each owner’s manual for further information on other devices.

DVD/VCR

AUDIO OUT

DVD

AUDIO

OUT

Stereo system

COAXIAL

DVD

DIGITAL

AUDIO OUT

COAXIAL

AUDIO

Method 1

Analog audio input jacks

Digital audio input jack

AUDIO OUT

DIGITAL AUDIO OUT

Method 2

Audio cable

(supplied)

Coaxial Digital

Audio cable

(not supplied)

Note

• If you connect this unit to a receiver with a Dolby Digital decoder and set “Dolby Digital” to “Stream” for the “Digital Out” setting in the SETUP menu. (Refer to pages 30-31.)

• If output is DTS encoded audio, connect to a DTS decoder and set “DTS” to “ON” for the “Digital Out” setting in the SETUP menu. (Refer to pages 30-31.)

• A Dolby Digital 5.1 channel surround format cannot be recorded as digital sound by an MD or DAT deck.

• Unless connected to a receiver with a Dolby Digital decoder or a DTS decoder, set “Dolby Digital” to “PCM” and “DTS” to “OFF” for the “Digital Out” setting in the SETUP menu. Playing a DVD using incorrect settings may generate noise distortion and may also damage the speakers. (Refer to pages 30-

31.)

• Set “Dolby Digital” to “PCM” for the “Digital Out” setting in the SETUP menu for connecting to an MD deck or DAT deck. (Refer to pages 30-31.)

• By hooking this unit up to a receiver with a Multichannel Dolby Digital decoder, you can enjoy highquality Dolby Digital 5.1 channel surround sound as heard in movie theaters.

Receiver with Dolby

Digital Decoder

This unit

(VCR/DVD Sound)

(DVD Sound Only)

(DVD Audio only)

Changing the SETUP menu

Playing discs VCR functions

Before you start

Connections Getting started

Recording Editing Others

Español

Getting started

Functional overview

Guide to On Screen Menus

The unit uses the following types of on screen menus for most operations. SETUP/DISC/CD menu,Title list, and DISPLAY menu, which allows you to change the playing status of disc during play.The DISPLAY menu also gives you some disc information for checking the status of the disc.

SETUP/DISC/CD menu

Press SETUP button to display the setup main menu, then choose either SETUP/DISC/CD by pressing { / B buttons.Then, press ENTER button to display each menu. These menus provide entry to all main functions of the unit.

1.Playback:

To set up the DVD/VCR to your preference.

2. Recording:

To set up the DVD/VCR to record to discs or tapes.

3. Display:

To set up the OSD screen of the DVD/VCR.

4. Select Video: (L1 or L2)

To choose a line input from external video products.

5.Clock:

To set up the clock of the unit as you need.

6. Channel:

To preset the TV channels.

1. Edit:

Turns on a title list, (When a disc with VR mode is inserted, 'Original' or 'PlayList' is available.), which shows the recorded titles on the disc.

2.Format:

Allows you to erase all of the recorded content on the disc. The disc will be completely blank.

3. Finalize:

Allows you to finalize a disc containing recorded titles.

4.Disc Protect (VR mode only) :

Allows you to protect a disc from accidental editing or recording.

1. Random Play:

To activate the random CD tracks playback.

2.Program Play(Audio CD only):

To activate the programmed CD tracks playback feature.

“CD” can only be selected when an Audio CD disc or a CD-R/RW disc with MP3 files is inserted into the unit.

“SETUP” is available only in the Stop mode.

“DISC” is available only when a DVD-R/RW disc is inserted into the unit. When a DVD-Video disc (commercially available), a new DVD-R disc or the finalized DVD-R disc is inserted into the unit, you cannot select “DISC”.

You will need to finalize the discs recorded in video mode to play in other DVD players.

Setup Menu

Setup

1 2 3

4 5 6

Playback Setting

Disc Setting

Disc

Edit

Format

Finalize

Disc Protect OFF ON

1 2 3

CD Playback Mode

Random Play

Program Play

1 2

Getting started

Functional overview (cont’d)

DISPLAY menu

First:

Press DISPLAY button to call up the display menu.This menu will give you the information on the playing disc. Some operations are available while disc is playing.

Details are on page

34.

1. Indicates the disc type and

the format mode.

2. Indicates the recording mode

and possible recording time left.

3. Indicates the current channel

number.

4. Indicates title number, chapter

number and the time elapsed of disc play.

5. Icon Description:

)

DVD mode

First:

Press DISPLAY button to call up the display menu.

1. Playback status of the current

tape.

2. Indicates the current channel

number and an audio status of the program.

3. Indicates the recording speed.

4. Indicates the Tape Counter.

5. Audio status of the current

tape.

VCR mode

Note:

In some descriptions on this manual, only one disc type is

indicated as an example.

DVD

11 00:00:00

DVD-RW

Video mode

SP 1:25 Rem.

CH 1

2 3

: Search

: Audio

: Subtitle

: Angle (except VR mode

: Repeat

: Marker

: Noise Reduction

: Zoom

VCR

0:00:00 HIFISP

CH21

4 53

Changing the SETUP menu

Playing discs VCR functions

Before you start

Connections Getting started

Recording Editing Others

Español

Getting started

Functional overview (cont’d)

Front Panel Display Guide

1. Current status of the unit

: Appears when disc/tape

play is paused.

: Appears when playing a

disc/tape.

: Appears when timer pro-

gramming has been set.

: Appears during recording

process.

: Appears when repeat playback is turned on.

: Appears when a tape is in

the unit.

2. Disc type and Current status of the unit

Appears when an audio CD or a disc with MP3 files is inserted in the DVD/VCR.

Appears when a DVD disc is inserted in the DVD/VCR. Appears when a DVD timer recording is proceeding. Appears when DVD is in the timer recording standby mode.

: Appears when a DVD-R disc is inserted in the DVD/VCR.

: Appears when a DVDRW disc is inserted in the DVD/VCR.

Appears when a VCR timer recording is proceeding. Appears when VCR is in the timer recording standby mode.

: Appears during VCR to DVD duplication process.

: Appears during DVD to VCR duplication process.

Display message

3. Recording speed

Indicates the recording speed of the disc or the tape.

4. Title/Track and Chapter mark

: Appears when indicating

a title/track number.

: Appears when indicating

a chapter number.

5. Displays the following

•Playing time / remaining time

• Current title / chapter / track number

• Recording time

• Clock

• Channel number

• VCR tape counter

•OTR remaining time

6. : Appears when the cur-

rent time is in the ‘pm’ portion of the day.

7. :

Appears when the progressive scan video output is activated.

1. Appears when the disc tray is

opening.

2. Appears when the disc tray is

closing or closed.

3. Appears when a disc is loading

inside the DVD/VCR.

4. Appears when data is record-

ing onto the disc.

Getting started

Channel settings

It is recommend that you preset available channels in your area using “Auto Preset” in the Channel Preset of the SETUP menu.

Presetting channels automatically

Press POWER button to turn on the unit.

Turn the TV on and be sure to select the input to which the DVD/VCR is connected.

Press SETUP button to display SETUP/DISC menu.

SETUP/DISC menu will appear.

Screen:

Select “SETUP” using { / B buttons, then press ENTER button.

SETUP menu will appear.

Select “Channel” using K / L / { / B buttons, then press ENTER button.

Channel Preset menu will appear.

Select “Auto Preset” using K / L buttons, then press ENTER button.

The unit will begin scanning channels available in your area.

This may take a few minutes to complete.

Press SETUP button to exit.

•You can select only the channels memorized in this unit by using the CHANNEL buttons.

Note

• If the auto presetting is cancelled during presetting, some channels not yet preset may not be received.

• The selection will depend on how you receive the TV channels.

To cancel the auto presetting during scanning:

Press RETURN button or SETUP button to cancel.

To select a channel

You can select a channel by directly entering channel using the Number buttons on the remote control.

Notes for using the Number buttons:

• When selecting cable channels

which are higher than 99, enter channel numbers as a three-digit number.(For example:

117,press 1, 1, 7)

• You must precede single-digit

channel numbers with a zero (For example:

02, 03, 04 and

so on).

•

You can select the line input mode (“L1” or “L2”).To select “L1” by pressing [0],[0],[1].To select “L

2” by pressing

[0],[0],[2].Details are on page 68.

POWER

REC SPEED

AUDIO

ZOOM SKIP SKIP

OPEN/CLOSE

TOP MENU

SPACE

VCR

SETUP

CM SKIP

TIMER PROG.

RETURN

123

456

7809

STOP

PLAY

VIDEO/TV

SLOW

PAUSE

.@/:

ABC DEF

GHI JKL MNO

PQRS

REC/OTR

REC MONITOR

MENU/LIST

CLEAR/C.RESET

MODE

ENTER

DISPLAY

TUV WXYZ

DVD

ONE TOUCH

DUBBING

4 5 6

Setup Menu

Setup

Playback Setting

Setup > Channel Preset

Auto Preset

Manual Preset

TV Audio Select

VCR DVD

Stereo

CH 18

Auto Presetting Now

Changing the SETUP menu

Playing discs VCR functions

Before you start

Connections Getting started

Recording Editing Others

Español

Getting started

Channel settings (cont’d)

Select “Manual Preset” using K / L buttons, then press

ENTER button.

Manual Preset menu will appear.

Select the channel number to add or delete.

Press { button to move to a lower channel number.

Press

B button to move to a

higher channel number.

Select “Add” or “Delete” using

K / L buttons, then

press ENTER button.

The channel number will be added or deleted from the channel memory.Then next channel number will appear so that you can continue adding or deleting channels.

Press SETUP button to exit.

Adding/deleting channels

The channels you no longer receive or seldom watch can be deleted from the memory.You also may add channels into memory.

Press SETUP button to display SETUP/DISC menu.

SETUP/DISC menu will appear.

Screen:

Select “SETUP” using { / B buttons, then press ENTER button.

SETUP menu will appear.

Select “Channel” using K / L / { / B buttons, then press ENTER button.

Channel Preset menu will appear.

2 3 4 5

Setup Menu

Setup

Setup > Channel Preset > Manual Preset

CH2

Add Delete

Setup > Channel Preset > Manual Preset

CH18

Add Delete

POWER

REC SPEED

.@/:

ABC DEF

123

GHI JKL MNO

456

PQRS

TUV WXYZ

7809

SPACE

VCR

DISPLAY

PLAY

STOP

SETUP

REC/OTR

REC MONITOR

MENU/LIST

TOP MENU

ZOOM SKIP SKIP

CLEAR/C.RESET

CM SKIP

MODE

AUDIO

ENTER

DVD

OPEN/CLOSE

VIDEO/TV

SLOW

PAUSE

TIMER PROG.

RETURN

ONE TOUCH

DUBBING

Playback Setting

Setup > Channel Preset

Auto Preset

Manual Preset

TV Audio Select

VCR DVD

Stereo

Getting started

Setting the clock

Set the clock before you try timer recording. If a Public Broadcasting Station (PBS) is available in your area, follow Auto Clock Setting below. If not, follow Manual Clock Setting on pages 19-20.

Auto Clock Setting

Make sure

• The antenna/cable TV connections are correct.

• If this unit is connected to a Cable Box or Satellite Box, select the local PBS station on the box to set the clock automatically.

Press SETUP button to display SETUP/DISC menu.

SETUP/DISC menu will appear.

Screen:

Select “SETUP”using

{ / B

but-

tons, then press ENTER button.

SETUP menu will appear.

Select “Clock” using

K / L / { / B

buttons, then press ENTER button.

Clock menu will appear.

Setup > Clock

Clock Setting

Auto Clock Setting

Daylight Saving Time

Auto

VCR DV D

Select “Auto Clock Setting” using

K / L buttons, then

press ENTER button.

Option window will appear.

• If you do not know your PBS channel number, select “Auto” using

K / L buttons, then press ENTER button and proceed to setp 6.

• If you know your PBS channel number, select “Manual” using

K / L buttons, then

press ENTER button.

Enter your PBS channel number using Number or

/ L buttons, then press ENTER button.

Press SETUP button to exit.

Press POWER button to turn off the unit.

This unit will search for the time only when the power is off. Leave it off for several minutes to give this unit time to set the clock on the display of the front panel.

Note : Clock Set

• The clock may set itself automatically after you connect the antenna/cable signal to this unit and plug in the power cord. In this case, the current time will appear on the display on the front panel.

• If the current time is not displayed or the displayed time is not correct, set the clock manually. (See Next Page.)

POWER

REC SPEED

AUDIO

ZOOM SKIP SKIP

OPEN/CLOSE

TOP MENU

SPACE

VCR

SETUP

CM SKIP

TIMER PROG.

RETURN

123

456

7809

STOP

PLAY

VIDEO/TV

SLOW

PAUSE

.@/:

ABC DEF

GHI JKL MNO

PQRS

REC/OTR

REC MONITOR

MENU/LIST

CLEAR/C.RESET

MODE

ENTER

DISPLAY

TUV WXYZ

DVD

ONE TOUCH

DUBBING

2 3 4 5

Setup > Clock

Clock Setting

Auto Clock Setting

Daylight Saving Time

VCR DV D

OFF

Auto

Auto Manual

Off

Setup Menu

Setup

Playback Setting

Setup > Clock

Clock Setting

Auto Clock Setting

Daylight Saving Time

VCR DV D

OFF

Set Channel No.

Auto

CH1

Manual

Off

Changing the SETUP menu

Playing discs VCR functions

Before you start

Connections Getting started

Recording Editing Others

Español

Getting started

Setting the clock (cont’d)

Manual Clock Setting

Press SETUP button to display SETUP/DISC menu.

SETUP/DISC menu will appear.

Screen:

Select “SETUP” using { / B buttons, then press ENTER button.

SETUP menu will appear.

Select “Clock” using K / L / { / B buttons, then press

ENTER button.

Clock menu will appear.

Select “Clock Setting” using K / L buttons, then press

ENTER button.

A clock setting window will appear.

Press ENTER button again.

Default date will appear.

Enter the date (month / day / year) using

K / L buttons.

Press { / B buttons to move the cursor.

Enter the time (hour / minute) using

K / L buttons.

Press { / B buttons to move the cursor.

Note : In Time of Power

Loss

• Your clock setting will be lost if either there is a power failure or this unit has been unplugged for more than

seconds when you set the clock manually.

POWER

REC SPEED

AUDIO

ZOOM SKIP SKIP

OPEN/CLOSE

TOP MENU

SPACE

VCR

SETUP

CM SKIP

TIMER PROG.

RETURN

123

456

7809

STOP

PLAY

VIDEO/TV

SLOW

PAUSE

.@/:

ABC DEF

GHI JKL MNO

PQRS

REC/OTR

REC MONITOR

MENU/LIST

CLEAR/C.RESET

MODE

ENTER

DISPLAY

TUV WXYZ

DVD

ONE TOUCH

DUBBING

2 3 4 5

Instructions continue on page 20.

Setup Menu

Setup

Playback Setting

Setup > Clock

Clock Setting

Auto Clock Setting

Daylight Saving Time

VCR DV D

Auto

- - : - -

VCR DV D

Auto

Setup > Clock

Clock Setting

Auto Clock Setting

Daylight Saving Time

- - - / - - / - - - - ( - - - )

12 : 00AM

VCR DV D

Auto

Setup > Clock

Clock Setting

Auto Clock Setting

Daylight Saving Time

JAN / 12 / 2004 (MON)

Setup > Clock

Clock Setting

Auto Clock Setting

Daylight Saving Time

JAN / 12 / 2004 (MON)

09 : 24 AM

VCR DV D

Auto

Getting started

Setting the clock (cont’d)

Press K / L buttons to select AM or PM, then press ENTER button.

Clock menu will appear, then the settings will be activated.

Press SETUP button to exit.

Although seconds are not displayed, they begin counting from zero.

POWER

REC SPEED

AUDIO

ZOOM SKIP SKIP

OPEN/CLOSE

TOP MENU

SPACE

VCR

SETUP

CM SKIP

TIMER PROG.

RETURN

123

456

7809

STOP

PLAY

VIDEO/TV

SLOW

PAUSE

.@/:

ABC DEF

GHI JKL MNO

PQRS

REC/OTR

REC MONITOR

MENU/LIST

CLEAR/C.RESET

MODE

ENTER

DISPLAY

TUV WXYZ

DVD

ONE TOUCH

DUBBING

ZOOM SKIP SKIP

TOP MENU

SETUP

CM SKIP

TIMER PROG.

RETURN

STOP

PLAY

REC/OTR

REC MONITOR

MENU/LIST

CLEAR/C.RESET

MODE

ENTER

ONE TOUCH

DUBBING

Select “Auto Clock Setting” using

K / L buttons, then

press ENTER button.

Option window will appear.

Repeat steps (1) to (3) in “Manual Clock Setting”.

When “Auto Clock Setting” is selected to “Auto” or “Manual”, change it to “OFF” as follows:

Select “OFF” using K / L buttons, then press ENTER button.

Press SETUP button to exit.

Setup > Clock

Clock Setting

Auto Clock Setting

Daylight Saving Time

VCR DV D

Auto

Setup > Clock

Clock Setting

Auto Clock Setting

Daylight Saving Time

VCR DV D

OFF

Auto

Auto Manual

Off

Changing the SETUP menu

Playing discs VCR functions

Before you start

Connections Getting started

Recording Editing Others

Español

Getting started

Setting the clock (cont’d)

Select “Daylight Saving Time” using

K / L buttons,

then press ENTER button.

Daylight Saving Time options will appear.

Select “ON” or “OFF” using K / L buttons, then press

ENTER button.

Choose “ON” when currently observing the daylight saving time.

Press SETUP button to exit.

Setting the daylight saving time

When Daylight Saving Time is ON, the unit clock will automatically move forward one hour on the first Sunday in April and move back one hour on the last Sunday in October.

Press SETUP button to display SETUP/DISC menu.

SETUP/DISC menu will appear.

Screen:

Select “SETUP” using { / B buttons, then press ENTER button.

SETUP menu will appear.

Select “Clock” using K / L / { / B buttons, then press

ENTER button.

Clock menu will appear.

2 3 4 5

Setup Menu

Setup > Clock

Clock Setting

Auto Clock Setting

Daylight Saving Time

VCR DV D

Auto

ON OFF

POWER

REC SPEED

.@/:

ABC DEF

123

GHI JKL MNO

456

PQRS

TUV WXYZ

7809

SPACE

VCR

DISPLAY

PLAY

STOP

SETUP

REC/OTR

REC MONITOR

MENU/LIST

TOP MENU

ZOOM SKIP SKIP

CLEAR/C.RESET

CM SKIP

MODE

AUDIO

ENTER

DVD

OPEN/CLOSE

VIDEO/TV

SLOW

PAUSE

TIMER PROG.

RETURN

ONE TOUCH

DUBBING

Setup

Playback Setting

Setup > Clock

Clock Setting

Auto Clock Setting

Daylight Saving Time

VCR DV D

Auto

Getting started

Selecting the TV aspect ratio

Yo u can select the TV aspect ratio to match the formats of what you are playing with the unit and your TV screen (

4:3 standard or 16:9 widescreen TV). “

4:3 Letter Box” has been select-

ed as the default.

Press SETUP button to display SETUP/DISC menu.

SETUP/DISC menu will appear.

Screen:

Select “SETUP” using { / B buttons, then press ENTER button.

SETUP menu will appear.

Select “Playback” using K / L / { / B buttons, then press ENTER button.

Playback menu will appear.

Select “TV Aspect” using K / L buttons, then press ENTER

button.

Option window will appear.

Refer to the Note on this page.

Select a desired option using K / L buttons, then press

ENTER button.

Press SETUP button to exit.

Note :TV Aspect

If you have a standard TV:

Select “4:3 Letter Box”, so that black bars appear on the top and bottom of the screen. Select “

4:3 Pan & Scan” for a full height picture with both sides trimmed.

If you have a widescreen TV:

Select “16:9 Wide”.

POWER

REC SPEED

AUDIO

ZOOM SKIP SKIP

OPEN/CLOSE

TOP MENU

SPACE

VCR

SETUP

CM SKIP

TIMER PROG.

RETURN

123

456

7809

STOP

PLAY

VIDEO/TV

SLOW

PAUSE

.@/:

ABC DEF

GHI JKL MNO

PQRS

REC/OTR

REC MONITOR

MENU/LIST

CLEAR/C.RESET

MODE

ENTER

DISPLAY

TUV WXYZ

DVD

ONE TOUCH

DUBBING

2 3 4 5

Setup Menu

Setup

Setup > Playback

TV Aspect

Parental Lock

Disc Menu Language

Audio Language

Subtitle Language

Digital Out

Dynamic Range Control

Fast Forward with Audio

DVD

16:9 Wide

4:3 Letter Box

4:3 Pan & Scan 16:9 Wide

English Original

OFF

Playback Setting

Setup > Playback

TV Aspect

Parental Lock

Disc Menu Language

Audio Language

Subtitle Language

Digital Out

Dynamic Range Control

Fast Forward with Audio

DVD

4:3 Letter Box

All

English

Original

OFF

Selecting TV stereo or SAP

Getting started

Changing the SETUP menu

Playing discs VCR functions

Before you start

Connections Getting started

Recording Editing Others

Español

You can select stereo or SAP. “Stereo” has been selected as the default.

Press SETUP button to display SETUP/DISC menu.

SETUP/DISC menu will appear.

Screen:

Select “SETUP” using { / B buttons, then press ENTER button.

SETUP menu will appear.

2 3 4 5

Select “Channel” using K / L / { / B buttons, then press ENTER button.

Channel Preset menu will appear.

Select “TV Audio Select” using

K / L buttons, then

press ENTER button.

Option window will appear.

Select “Stereo” or “SAP” using K / L buttons, then press ENTER button. Stereo:

Outputs main-audio.

SAP: (Secondary Audio Program)

Outputs second audio channel. Refer to the item in “Glossary” on page 102 for more information.

Press SETUP button to exit.

Notes on TV channel audio

• When you record a TV program which has Stereo and Secondary Audio Programs on a DVD-RW/R or a tape, you have to select the TV channel audio (Stereo or SAP) beforehand. Only the selected channel audio will be recorded. Refer to the following table to check an appropriate setting.

• As can be seen in the table on the right, if your TV channel audio is set to SAP and the recorded TV program has Stereo and Secondary Audio Programs, you can only view the program in the sub-audio.

Selected Broadcast Disc/tape Audio audio audio recording output

Stereo STEREO+SAP STEREO STEREO

STEREO STEREO STEREO MONO+SAP MONO MONO MONO MONO MONO

SAP STEREO+SAP SAP SAP

STEREO STEREO STEREO MONO+SAP SAP SAP MONO MONO MONO

Setup Menu

Setup > Channel Preset

Auto Preset

Manual Preset

TV Audio Select

VCR DVD

Stereo

Setup > Channel Preset

Auto Preset

Manual Preset

TV Audio Select

VCR DVD

Stereo

SAP

POWER

REC SPEED

.@/:

ABC DEF

123

GHI JKL MNO

456

PQRS

TUV WXYZ

7809

SPACE

VCR

DISPLAY

PLAY

STOP

SETUP

REC/OTR

REC MONITOR

MENU/LIST

TOP MENU

ZOOM SKIP SKIP

CLEAR/C.RESET

CM SKIP

MODE

AUDIO

ENTER

DVD

OPEN/CLOSE

VIDEO/TV

SLOW

PAUSE

TIMER PROG.

RETURN

ONE TOUCH

DUBBING

Setup

Playback Setting

RF converter output

Getting started

Change from CH3 to CH4

You can watch TV programs through the tuner of the unit. (Usually channel

3 or 4 of the TV is available for the RF converter setting.) Be

sure to connect the unit to a TV using the RF cable. Refer to page 10.

Select channel 3 on your TV.

• Be sure that the unit is in DVD mode.

Press VIDEO/TV button on the remote control.

• If noise appears, change the RF output channel of the DVD/VCR to CH

4 by pressing VIDEO/TV button for 3 seconds.The RF output

channel will alternate between CH

3 and CH4 as follows.

Press VIDEO/TV button

for more than 3 seconds

Note:

•

RF channel change is available only when the unit is in DVD mode.

POWER

REC SPEED

AUDIO

.@/:

ABC DEF

123

GHI JKL MNO

456

PQRS

TUV WXYZ

7809

SPACE

VCR

DISPLAY

DVD

OPEN/CLOSE

VIDEO/TV

SLOW

PAUSE

(

RF on)

(

RF on)

(

RF on)

3 seconds

CH4

3 seconds

CH3

3 seconds

CH4

3 seconds

REC/OTR

REC MONITOR

MENU/LIST

TOP MENU

CLEAR/C.RESET

CM SKIP

MODE

PLAY

STOP

SETUP

TIMER PROG.

ENTER

RETURN

ZOOM SKIP SKIP

ONE TOUCH

DUBBING

Changing the SETUP menu

Playing discs VCR functions

Before you start

Connections Getting started

Recording Editing Others

Español

Changing the SETUP menu

Tour of the SETUP menu

Note : Setup

• If you change a setting in SETUP menu, the information of contents stays on even when the power is switched off.

The following table shows the settings that are available in the SETUP menu and which are the default settings. Refer to the following table for useful operation.

SETUP menu ContentsItems (highlight is the default)

1.Language setting

Pages 26-27

Disc Menu Language Set the language for disc menu.

English French Spanish

2.Display setting Pages 28-29

3.Audio setting Pages 30-31

4.Parental setting Pages 32-33

Audio Language

Subtitle Language

OSD Background Transparency

OSD Background Color

OSD Language

Screen Saver

Digital Out

Dynamic Range Control

Fast Forward with Audio

Parental Lock

(Change password)

Original English French

OFF English French

100%

35% 25%

1 2 3

English

Français Español

OFF 5 minutes 10minutes

Dolby Digital PCM

Stream PCM

Auto 48kHz 96kHz

DTS ON OFF

ON OFF

ALL level 8 to 1

Enter the current four-digit password

Set the language for audio.

Set the language for subtitle.

Set the background transparency of OSD screen.

Set the OSD screen color. 1 (Green), 2 (Blue), 3 (Red)

Set the language for OSD (On Screen Display).

Set the time at which point the screen saver turn on.

Set the type of sound signal which outputs from the digital audio output jack.

Set whether the sound recorded in 96kHz will be down sampled to 48kHz.

Set whether DTS signal will be output or not.

Compressing the range of sound volume.

Outputting sound during playback in fast forward.

Set the parental level of your DVD discs.

Set and change the password.

Language settings

Changing the SETUP menu

Press SETUP button to display SETUP/DISC menu.

SETUP/DISC menu will appear.

Select “SETUP” using { / B buttons, then press ENTER button.

SETUP menu will appear.

Select “Playback” using K / L /

{ / B

buttons, then press

ENTER button.

Option window will appear.

Select a desired item using K / L buttons, then press ENTER button.

Note : Languages

• Only the languages supported by the disc can be selected.

•Audio Language setting may not be available on some discs.

•You can change or switch off the subtitles on a DVD disc also from the disc menu if it

is available.

Press STOP button if you are playing a disc.

Setup Menu

Setup

Playback Setting

POWER

REC SPEED

.@/:

ABC DEF

123

GHI JKL MNO

456

PQRS

TUV WXYZ

7809

SPACE

VCR

DISPLAY

PLAY

STOP

SETUP

REC/OTR

REC MONITOR

TOP MENU

MENU/LIST

ZOOM SKIP SKIP

CLEAR/C.RESET

CM SKIP

MODE

AUDIO

DVD

ENTER

OPEN/CLOSE

VIDEO/TV

SLOW

PAUSE

TIMER PROG.

RETURN

ONE TOUCH

DUBBING

Setup > Playback

TV Aspect

Parental Lock

Disc Menu Language

Audio Language

Subtitle Language

Digital Out

Dynamic Range Control

Fast Forward with Audio

4:3 Letter Box

All

English

Original

OFF

DVD

Language settings (cont’d)

Changing the SETUP menu

Playing discs VCR functions

Before you start

Connections Getting started

Recording Editing Others

Español

Disc Menu Language (Default : English)

Set the language for Disc Menu.

•

Select a setting using K / L buttons, then press ENTER button.

Your setting will be activated.

•

Select a setting using K / L buttons, then press ENTER button.

Your setting will be activated.

•

Select a setting using K / L buttons, then press ENTER button.

Your setting will be activated.

Audio Language (Default : Original)

Set the Audio language.

Subtitle Language (Default : OFF)

Set the subtitle language.

If “Other” is selected, press 4-digit code using number buttons.

All

•

When you finish entering the code, press ENTER button. Refer to the language code table on page

103.

Press SETUP button to exit SETUP menu.

Setup > Playback

TV Aspect

Parental Lock

Disc Menu Language

Audio Language

Subtitle Language

Digital Out

Dynamic Range Control

Fast Forward with Audio

Setup > Playback

TV Aspect

Parental Lock

Disc Menu Language

Audio Language

Subtitle Language

Digital Out

Dynamic Range Control

Fast Forward with Audio

DVD

4:3 Letter Box

All

English

Original

OFF

DVD

4:3 Letter Box

All

English

Original

OFF

Setup > Playback

TV Aspect

Parental Lock

Disc Menu Language

Audio Language

Subtitle Language

Digital Out

Dynamic Range Control

Fast Forward with Audio

Setup > Playback

TV Aspect

Parental Lock

Disc Menu Language

Audio Language

Subtitle Language

Digital Out

Dynamic Range Control

Fast Forward with Audio

DVD

4:3 Letter Box

All

English

French

Original

Spanish

OFF

Other

OFF

DVD

4:3 Letter Box

All

Original

English

Original

French

OFF

Spanish Other

OFF

Setup > Playback

TV Aspect

Parental Lock

Disc Menu Language

Audio Language

Subtitle Language

Digital Out

Dynamic Range Control

Fast Forward with Audio

DVD

4:3 Letter Box

All

English

Original

OFF

Setup > Playback

TV Aspect

Parental Lock

Disc Menu Language

Audio Language

Subtitle Language

Digital Out

Dynamic Range Control

Fast Forward with Audio

DVD

4:3 Letter Box

All

OFF

English

Original

French

OFF

Spanish Other

OFF

ontrol

English

French

Original

Spanish

OFF

Other

Code Input

- - - -

Changing the SETUP menu

Display settings

Press SETUP button to display SETUP/DISC menu.

SETUP/DISC menu will appear.

Select “SETUP” using { / B buttons, then press ENTER button.

SETUP menu will appear.

Select “Display” using K / L /

{ / B

buttons, then press

ENTER button.

Option window will appear.

Select a desired item using K / L buttons, then press ENTER button.

Press STOP button if you are playing a disc.

Setup Menu

Setup

Playback Setting

POWER

REC SPEED

.@/:

ABC DEF

123

GHI JKL MNO

456

PQRS

TUV WXYZ

7809

SPACE

VCR

DISPLAY

PLAY

STOP

SETUP

REC/OTR

REC MONITOR

TOP MENU

MENU/LIST

ZOOM SKIP SKIP

CLEAR/C.RESET

CM SKIP

MODE

AUDIO

DVD

ENTER

OPEN/CLOSE

VIDEO/TV

SLOW

PAUSE

TIMER PROG.

RETURN

ONE TOUCH

DUBBING

Setup > Display

OSD Background Transparency

OSD Background Color

OSD Language

Screen Saver

35%

English

10 minutes

DVD

Display settings (cont’d)

Changing the SETUP menu

Playing discs VCR functions

Before you start

Connections Getting started

Recording Editing Others

Español

OSD Background Transparency (Default : 35%)

Set the background transparency of OSD screen. You can choose one among 0% through 100%.

•

Select a setting using K / L buttons, then press ENTER button.

Your setting will be activated.

•

Select a setting using K / L buttons, then press ENTER button.

Your setting will be activated.

•

Select a setting using K / L buttons, then press ENTER button.

Your setting will be activated.

OSD Background Color (Default : 1 Green)

Set the OSD screen color. You can choose among the following options 1(Green), 2(Blue), and 3(Red).

OSD Language (Default : English)

Set the OSD language.

•

Select a setting using K / L buttons, then press ENTER button.

Your setting will be activated.

Screen Saver (Default : 10 minutes)

Set the time at which point the screen saver function appears on the TV screen.

Press SETUP button to exit SETUP menu.

Setup > Display

OSD Background Transparency

OSD Background Color

OSD Language

Screen Saver

Setup > Display

OSD Background Transparency

OSD Background Color

OSD Language

Screen Saver

DVD

35%

English

10 minutes

DVD

35%

English

10 minutes

Setup > Display

OSD Background Transparency

OSD Background Color

OSD Language

Screen Saver

Setup > Display

OSD Background Transparency

OSD Background Color

OSD Language

Screen Saver

DVD

100%

35%

85%

70%

English

50%

10 minutes

35% 25% 10% 0%

DVD

35%

1 2

English

10 minutes

Setup > Display

OSD Background Transparency

OSD Background Color

OSD Language

Screen Saver

VCR DVD

35%

English

10 minutes

Setup > Display

OSD Background Transparency

OSD Background Color

OSD Language

Screen Saver

VCR DVD

35%

English

English Français

10 minutes

Español

Setup > Display

OSD Background Transparency

OSD Background Color

OSD Language

Screen Saver

DVD

35%

English

10 minutes

Setup > Display

OSD Background Transparency

OSD Background Color

OSD Language

Screen Saver

DVD

35%

OFF

English

5 minutes 10 minutes

10 minutes 15 minutes 30 minutes

Changing the SETUP menu

Audio settings

Digital Out

Sets the digital audio output for discs when connected through the coaxial digital audio output.

•

Select a setting using K / L buttons, then press ENTER button.

Option window will appear. Proceed to steps A or B.

Press SETUP button to display SETUP/DISC menu.

SETUP/DISC menu will appear.

Select “SETUP” using { / B buttons, then press ENTER button.

SETUP menu will appear.

Select “Playback” using K / L /

{ / B

buttons, then press

ENTER button.

Option window will appear.

Select a desired item using K / L buttons, then press ENTER button.

Press STOP button if you are playing a disc.

Choose the appropriate Audio settings for your equipment.

It will only affect DVD discs during playback.

Note : Dynamic Range

Control

• Dynamic Range Control function is available only on the discs which are recorded in

the Dolby Digital format.

Setup Menu

Setup

Playback Setting

POWER

REC SPEED

.@/:

ABC DEF

123

GHI JKL MNO

456

PQRS

TUV WXYZ

7809

SPACE

VCR

DISPLAY

PLAY

STOP

SETUP

REC/OTR

REC MONITOR

MENU/LIST

TOP MENU

ZOOM SKIP SKIP

CLEAR/C.RESET

CM SKIP

MODE

AUDIO

DVD

ENTER

OPEN/CLOSE

VIDEO/TV

SLOW

PAUSE

TIMER PROG.

RETURN

ONE TOUCH

DUBBING

Setup > Playback

TV Aspect

Parental Lock

Disc Menu Language

Audio Language

Subtitle Language

Digital Out

Dynamic Range Control

Fast Forward with Audio

DVD

4:3 Letter Box

All

English

Original

OFF

Setup > Playback

TV Aspect

Parental Lock

Disc Menu Language

Audio Language

Subtitle Language

Digital Out

Dynamic Range Control

Fast Forward with Audio

DVD

4:3 Letter Box

All

English

Original

OFF

Setup > Playback

TV Aspect

Parental Lock

Disc Menu Language

Audio Language

Subtitle Language

Digital Out

Dynamic Range Control

Fast Forward with Audio

4:3 Letter Box

All

English

Original

OFF

PCM

Dolby Digital DTS

OFF

DVD

+ 78 hidden pages