Page 1
USER’S GUIDE
SRCD2731BT
Bluetooth CD Radio Microsystem
PLEASE READ BEFORE OPERATING THIS EQUIPMENT
Page 2
2
Page 3
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualifed service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord
or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
NOTE: This equipmenthas beentestedand found to comply or has
been dropped.
with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for
help .
•
The apparatus shall not be exposed to dripping or splashing and
that no objects flled with liquids, such as vases, shall be placed
on apparatus.
•
Main plug is used as disconnect device and it should remain readily
operable during intended use. In order to disconnect the apparatus
from the mains completely, the mains plug should be disconnected
form the mains socket outlet completely.
•
Battery shall not be exposed to excessive heat such as sunshine,
fire or the like.
•
Caution marking is located at the rear or back of the apparatus.
•
The marking information is located at the rear or back of apparatus.
L’appareil ne doit pas être exposé aux écoulements ou aux
éclaboussures et aucun objet ne contenant de liquide, tel qu’un
vase, ne doit être placé sur l’objet.
La prise du secteur ne doit pas être obstruée ou doit être facilement
accessible pendant son utilisation. Pour être complètement
déconnecté de l’alimentation d’entrée, la prise doit être débranchée
du secteur.
Les piles ne doivent pas être exposées à de forte chaleur, tel qu’à
la lumière du soleil, au feu ou autres choses de semblable.
Attention marquage est situé à l’arrière ou à l’arrière de l’appareil.
Les informations de marquage est situé à l’arrière ou à l’arrière de
l’appareil.
FCC Warnings
Additional Warnings
1 Read these Instructions.
2
Keep these Instructions.
3
Heed all Warnings.
4
Follow all instructions.
5
Do not use this apparatus near water.
6
Clean only with a dry cloth.
7
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8
Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifers) that produce heat.
9
Do not defeat the safety purpose of the polarized or
grounding - type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety.
When the provided plug does not ft into your outlet,
consult an electrician for replacement of the obsolete
outlet.
10
Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11
Only use attachments/accessories specifed by the
manufacturer.
12.
Important Safety Instructions
This symbol indicates that this product
incorporates double insulation between
hazardous mains voltage and user
accessible parts.
Use only with a cart, stand, tripod,
bracket, or table specifed by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination
to avoid injury from tip-over.
3
Page 4
Introduction
OPEN/CLOSE
Press to open or close
the CD door
.
SKIP/SEARCH/TUNE(+/-)
Press to skip between tracks
on loaded CD or Bluetooth.
Press and hold to search
through an individual track.
Press to tune the FM radio.
Press to adjust the time
when setting the clock.
STANDBY INDICATOR
LED light up indicated
Standby mode.
EQ
Press to switch the preset
EQ to Pop, Jazz, Classic,
Rock or Normal.
3.5MM HEADPHONE
INPUT
STOP
Press to stop a CD
during play.
MEN/CLK SET
Press to set the clock or
save a radio station.
REPEAT
Press to repeat the
current track or an
entire album/playlist.
PAIRING/PLAY/PAUSE
Press to play or pause a
loaded CD.
Press & hold to begin
pairing a Bluetooth device.
SOURCE
Press to switch to CD, LINE
IN, Radio or Bluetooth
modes.
PROGRAM
Press to program a loaded
disc to play tracks in a
VOLUME
Turn to adjust the volume
up or down.
MEM(+/-)
Press the cycle through saved
radio stations.
3.5MM AUDIO INPUT
DC POWER INPUT
CD COMPARTMENT
POWER
Press to power the
LCD DISPLAY
REMOTE SENSOR
SPEAKER TERMINAL
FM ANTENNA WIRE
Connected to external
speakers.
4
Page 5
STANDBY
Pres to power the music
system o or on.
MUTE
Press to mute the volume.
VOLUME
Press to adjust the volume.
SOURCE
Press to switch to CD, LINE
IN, Radio or Bluetooth
modes.
SKIP/SEARCH/TUNE-
Press to skip between tracks
on loaded CD or Bluetooth.
Press and hold to search
through an individual track.
Press to tune the FM radio.
Press to adjust the time
when setting the clock.
OPEN/CLOSE
Press to open or close
the CD door
.
REPEAT
Press to repeat the
current track or an
entire album/playlist.
SKIP/SEARCH/TUNE+
Press to skip between tracks
on loaded CD or Bluetooth.
Press and hold to search
through an individual track.
Press to tune the FM radio.
Press to adjust the time
when setting the clock.
EQ
Press to switch the preset
EQ to Pop, Jazz, Classic,
Rock or Normal.
MEM(+/-)
Press the cycle through saved
radio stations.
MEN/CLK SET
Press to set the clock or
save a radio station.
PROGRAM
Press to program a loaded
disc to play tracks in a
specied order.
STOP
Press to stop a CD
during play.
PAIRING/PLAY/PAUSE
Press to play or pause a
loaded CD.
Press & hold to begin
pairing a Bluetooth device.
5
Page 6
Plug the included AC/DC power
adapter into the DC POWER INPUT on
the music system and an AC power
outlet to power the music system.
Requires 1, CR2025, battery (preinstalled).
Power
Battery Power
LITHIUM BATTERY
CR 2025
3V
CR2025
PUSH
OPEN
LITHIUM B
A
T
TE
RY
CR 2025
3V
CR2025
PUSH
OPEN
Setup
Clock
1. Press the POWER button to turn
2. Press and hold the MEM/CLK SET
button on the music system.
The hour will begin to blink on the
display.
3. Press the SKIP/SEARCH buttons to
adjust the hour.
An “AM” indicator will appear on the
display when the time is set to the
AM. A “PM” indicator will appear on
the display when the time is set to
the PM.
Setting the Clock
Press the MEM/CLK SET button to
set the minute.
The minute will begin to blink on the
display.
4.
5.
6.
Press the SKIP/SEARCH buttons to
adjust the minute.
Press the MEM/CLK SET button to
6
Page 7
1. Press the OPEN/CLOSE button
on the top of the music system to
open the CD door.
2. Load a CD into the music system,
label side facing up.
3. Close the CD door.
1. Follow the instructions for Loading
a CD.
2. Press the POWER button to power
the music system on.
3. Press the SOURCE button to switch
to CD mode. The CD will playing
automatically.
The track number will appear on the
display, to the right of the time, when
the music system is in CD mode.
4. Press the PLAY/PAUSE button to
pause a loaded disc. press again
to resume.
1. Follow the instructions for Playing
a CD.
2. Press the STOP button.
The loaded disc must be stopped to
create a program.
3. Press the PROG. button on the
front of the music system.
“PROG” and a number, indicating
the order in which the next selected
track will play, will appear on the
display.
4. Press the SKIP/SEARCH buttons to
select a track.
5. Press the PROG. button again
to save the selected track to the
program.
6. Repeat steps 4 and 5 to program
up to 20 tracks to play in the order
they were selected.
1. After programming the CD, press
the STOP button twice to cancel
the program.
Loading a CD
Playing a CD
Programming a CD
Cancelling a Programmed CD
CD
5 Press the STOP button to stop a
loaded disc .
7
Page 8
1. Press the POWER button to power
the music system on.
2. Press the SOURCE button to
switch to FM radio mode.
“FM” will appear on the display.
3. Press the TUNE +/- buttons to tune
the FM radio.
Adjust the position of the FM wire
antenna to improve FM radio
reception.
1. Follow the instructions for Tuning
the FM Radio and Saving an FM
Radio Station.
2. Press the MEM± buttons to
cycle through saved radio stations.
1. Follow the instructions for Tuning
the FM Radio.
2. Press the TUNE +/- buttons to tune
the FM radio to the desired station.
3. Press the MEM/CLK SET button on
on the music system or the
MEM/CLK SET button on the
remote.
A preset number (P01) will appear on
the display, indicating which preset
the current station will be saved to.
4. Press the MEM +/- buttons to
adjust the preset number (P01 P20).
5. Once the desired preset is selected,
press the MEM/CLK SET button on
the music system or the MEM/CLK SET
button on the remote to save the
current FM radio station to the
selected preset.
Tuning the FM Radio
Playing a Saved Radio Station
Saving an FM Radio Station
FM Radio
8
Page 9
Bluetooth
1. Press the POWER button to power
the music system on.
2.
Press the SOURCE button to
switch to Bluetooth mode.
“ ” will appear on the display and blanking.
3.
Press and hold the PAIRING/PLAY/PAUSE
button to begin pairing to a Bluetooth
device, “ ” will flash quickly.
4.
Using the native controls on your Bluetooth
device, select the SRCD2731BT in your
Bluetooth settings to pair. If your device
requests a password, enter the default
password "0000".
Refer to the user's manual for your specic
device for instructions on pairing and
connecting Bluetooth devices.
5.
When successfully paired and connected, a
beep will issue from the unit and the " "
will display a solid light.
After initial pairing, the unit will stay paired
unless unpaired manually by the user or
erased due to a reset of the device. If your
device should become unpaired or your nd it
is unable to connect, repeat the above steps.
Pairing a Bluetooth Device for the first time
Playing Audio Wirelessly
1.
After pairing to a Bluetooth device,
use the native controls on the con-
nected Bluetooth device to select a
track.
2.
Play, pause or skip a selected track
using the native controls on the
connected Bluetooth device or the
controls on the unit machine.
3.
Audio played trough the
connected Bluetooth device will
now be heard through the
speakers.
9
Page 10
Line in
Requires a 3.5mm audio cable (not
included).
1. Connect a 3.5mm audio cable to
the LINE IN jack on the music
system and the headphone
jack or 3.5mm audio output on an
MP3 player or other audio source.
2. Press the POWER button to power
on the music system.
3. Press the SOURCE button to
switch to LINE IN mode.
4. Use the native controls on the
connected MP3 player or other
audio source to control the music
played through the music system.
Using the 3.5mm Audio Input
Using Headphones (not included)
If you would like to listen to your music
privately through the use of
headphones, you may do so in one step.
Simply plug your eadphones into the
phones jack, located on front the unit.
Compatible headphones have a 3.5mm
diameter stereo plug and an impedance
of 8-32 Ohms. When your headphones
are connected, the stereo speakers are
automatically disconnected.
10
Page 11
Specication
Power Adaptor:
AC input 120V~60Hz
DC Output 10.5V 1.5A
Bluetooth:
Bluetooth Specification version 2.1
Support profile A2DP
Frequency Range: FM 87.5 – 108 MHz
Power output:
5W (RMS) x 2
6 Kg.
Dimensions:
Weight:
32cm (H) x 72 cm (W) x 21 cm (D)
11
Page 12
This quality product is warranted to be free from manufacturer’s defects in material and workman-ship,
provided that the unit is used under the normal operating conditions intended by the manufacturer.
Should you have any problem with this product, please and it is highly recommended to visit our website
at www.curtisint.com
before you take any other steps as we have additional copies of instruction manuals,
operating manuals and trouble shooting tips on our website which gives you the answer on most of the
questions you could have in operating the unit.
TERMS OF WARRANTY
C.I. Service Dept. warrants this product to be free from defects in materials and workmanship for 90 days on
parts and 90 days on labor. If you originally
purchased your product more than 90 days ago, a repair fee
may apply.
Nothing within this warranty shall imply that C.I. will be responsible or liable for any damage to any items
placed in this product, whether due to any defect of the product, or its use, whether proper or improper.
EXCLUSIONS
Save as herein provided, C.I. Service Dept. (Canada) or C.I. Service Dept. (USA), there are no other
warranties
, conditions, representations or guarantees, express or implied, made or intended by C.I. or its
authorized distributors and all other warranties, conditions, representations or guarantees, including any
warranties, conditions, representations or guarantees under any Sale of Goods Act or like legislation or
statue is hereby expressly excluded. Save as herein provided, C.I. Service Dept. (Canada) or
C.I. Service
Dept. (USA), shall not be responsible for any damages to persons or property, including the unit itself,
howsoever caused or any consequential damages arising from the malfunction of the unit and by the
purchase of the unit, the purchaser does hereby agree to indemnify and save harmless C.I. from any claim
for damages to persons or property caused by the unit.
TO OBTAIN REPAIRS UNDER THE TERMS OF THIS WARRANTY
1. The original purchaser must present a copy of the original bill of sale and the service warranty card.
2. Any alterations, abuse, misuse, battery corrosion or accidental damage voids the warranty.
3. The warranty does not cover cabinets and accessories.
4. No warranty or insurance contained or set out shall apply when damage or repair is caused by power
failure; damage in transit or when moving the unit; improper power supply; use for commercial or
industrial purposes; service calls resulting in customer education, etc.
5. The defective product should be mailed to:
Canada U.S.A
C.I. Service Dept. Cur
s Interna onal Ltd
315 A well Drive
Toronto, ON
M9W 5C1
c/o Liquidity Services/Liquida on.com
1399 Perry Road
Plainfield, IN
46168
For service assistance and product information, please call: 1-800-968-9853.
If mailing the product, the freight must be prepaid and a money order for $7.00 should be included
to cover the cost of insurance and the return of the product.
6. C.I. reserves the right to repair or replace the parts which have become defective.
Model No.
Date Purchased
Serial No.
is a registered trademark of OSRAM SYLVANIS Inc. used under licence.
LIMITED PRODUCT WARRANTY
Loading...