Sylvania RSDCT2703R User Manual

Date of Purchase Dealer Purchase from Dealer Address
Dealer Phone No. Model No. Serial No.
ANT.IN
Owner’s
DURABRAND
Limited
WARRANTY
WAL-MART warrants this product to be free from manufacturing defects, in material and workmanship under normal use and conditions for a designated period from date of original purchase in Canada. For a WARRANTY period of
18 MONTHS
Should service be necessary under this warranty for any reason due to manufacturing defect during the warranty period, Wal-Mart Canada will repair or replace (at its discretion) the defective merchandise at no charge.
THIS UNIT CAN BE REP AIREDAND OR REPLACED BY WAL-MART CANADA SERVICE NOTE: This warranty is void if the product is:
(a) Damaged through negligence, misuse, abuse, or accident. (b) Used in a commercial application or rentals. (c) Modified or repaired by anyone other than Wal-Mart Canada. (d) Damage caused by improper connection to other equipment. (e) If the original proof of purchase cannot be supplied.
NOTE: This warranty does not cover:
(a) Damage to the tape or tape cartridge (if applicable). (b) Cleaning of video heads (if applicable). (c) Damage occurred or costs incurred in the shipping of the product to Wal-Mart
Canada.
(d) Ordinary adjustments to the product which can be performed by customer as out-
lined in the ownerÕs manual. (e) Signal reception problems caused by external antenna, cable systems or interference. (f ) Incompatibility due to the change in TV/CATV broadcast systems after the product
was sold.
THIS WARRANTY IS NON-TRANSFERABLE AND APPLIES ONLY TO THE ORIGNAL PUR- CHASER AND DOES NOT EXTEND TO SUBSEQUENT OWNERS OF THE PRODUCT, ANY APPLICABLE IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANT ABILITY, ARE LIMITED IN DURATIONTOA PERIOD OF THE EXPRESSED WARRANTY AS PROVIDED HEREIN BEGINNING WITH THE DATE OF ORIGINAL PURCHASE AT RETAIL AND NO WARRANTIES, WHETHER EXPRESSED OR IMPLIED, SHALL APPLY TO THIS PRODUCT THEREAFTER. UNDER NO CIRCUMSTANCES SHALL WAL-MART CANADA BE LIABLE FOR ANY LOSS, DIRECT ,INDIRECT,INCIDENTAL,SPECIAL,ORCONSEQUENTIALDAMAGEARISINGOUTOF , ORINCONNECTIONWITH THE USE OF THIS PRODUCT.
WAL-MART CANADA Inc.
1940 Argentia Road
Mississauga, Ontario
L5N 1P9
Canada
SYLVANIA
12
RSDCT2703R
SYLVANIA
Funai Corporation
Funai Corporation
Funai Corporation
Funai Corporation
Funai
Corporation
Manual
FEATURES
Tinted, Bright Black Matrix Picture Tube
181 Channel Selection- All VHF/UHF channels plus up to 125 cable channels.
PLL Frequency Synthesized Tuning- The latest PLL frequency synthesized electronic tun-
ing system provides free and easy channel selection, and lets you tune directly to any channel using the channel number buttons (0~9 and +100-key) on the remote control.
On-Screen Function Display
Full-Function Remote Control
Sleep Timer
Closed Caption Decoder- You may view specially labeled (cc) TV programs, movies, news,
prerecorded tapes, etc. with either a dialogue caption or text display added to the program.
Auto Shut Off Function- If there is no air signal input from the antenna terminal and no
operation for 15 minutes, the TV will turn itself off automatically.
V-CHIP- Enables parents to prevent their children from watching inappropriate material on TV.
Front / Rear AV Input
PRECAUTION
Place your TV in a room with adequate ventilation.
Keep your TV set away from sources of direct heat, such as heat registers or direct sunlight.
Do not place your TV on soft surfaces, such as rugs or blankets.
Leave enough room for air to circulate around the bottom, top and back of the set.
NOTE: CHANNEL SET UP MUST BE COMPLETED BEFORE THE SET WILL
FUNCTION PROPERLY. SEE INSIDE FOR PROCEDURE.
The serial number of this product may be found on the back of the TV. No others have the same serial number as yours. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft.
27 INCH COLOR TELEVISION
DCT2703R
0EMN02199 Printed in Malaysia
L6605CF * * * * *
ANTENNA/CABLE CONNECTIONS
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
UHF Antenna (Not supplied)
VHF Antenna
(Not supplied)
UHF/VHF Rod Antenna (Not supplied)
CLOSED CAPTION
This TV can receive C1 and C2 Caption and Text.
(1)Closed Caption Characters can be displayed on the TV screen only when the received broad-
(2)Paint-on mode: Displays input characters on the screen immediately.
Note: If CAPTION C1 or C2 is selected but a Closed Caption signal is not included, characters will not be displayed.
(1)Displays the text on the screen by scrolling (max. 7 lines)
Caption Mode
cast signal contains the Caption Signals.
Pop-on mode: Once characters are stored in memory, they are displayed all at once. Roll-up mode: Displays the characters continuously by scrolling (max. 4 lines)
Text Mode
(2)If the received broadcast signal does not contain caption or text signals, no change will occur.
VHF/UHF Combination Antenna (Not supplied)
VHF/UHF Combiner (Not supplied)
OR
This Owner’s Manual is made of recycled paper.
Some cable TV systems use scram-
*
bled signals and require a special con­verter to receive these channels. Consult your local cable company.
ANT. IN
CATV Box or Satellite Box (Not supplied)
OUT
OR
*
IN
75-ohm Coaxial Cable
Note to CATV system installer:
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.
From Cable System or Satellite Antenna 75-ohm Coaxial Cable
From Cable System
Notes:
(1)When your TV receives a special effects playback signal (i.e., Search, Slow, Still) from a
VCR’s video output channel (CH3 or CH4), your TV may not display the correct caption or
text. (2)Captions and texts may not match the TV voice exactly. (3)Interference may cause the closed caption system not to function properly. (4)The caption or text characters will not be displayed while the menu display or function’s dis-
play is shown. (5)If you see this screen:
If your TV displays a black box on the screen, this means that your TV is set to TEXT mode. To clear screen, select CAPTION C1, C2 or CAPTION [OFF].
WARNING
PORTABLE CART WARNING
S3126A
FIGURE A
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ELECTRIC SERVICE EQUIPMENT
GROUND CLAMP
NEC - NATIONAL ELECTRICAL CODE POWER SERVICE GROUNDING
ELECTRODE SYSTEM (NEC ART 250, PART H)
S2898A
GROUND CLAMPS
GROUNDING CONDUCTORS (NEC SECTION 810-21)
ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)
ANTENNA LEAD IN WIRE
MENU POWER
123456 7 8
L - AUDIO - RVIDEO
VOLUME CHANNEL
HEADPHONE
9
AUDIO
L
R
VIDEO
ANT.IN
17342
16
POWER
123
456
789
0 +100
DISPLAY
VOL
CH
CH
VOL
SLEEP
CHANNEL
RETURN
8
15
6
5
10
12
11
13
MUTE
MENU
7
GAME
14
:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLI­ANCE TO RAIN OR MOISTURE.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SER­VICING TO QUALIFIED SERVICE PERSONNEL.
The important note is located on the rear of the cabinet.
CAUTION
THIS SYMBOL INDICATES THAT DAN­GEROUS VOLTAGE CONSTI-TUTING A RISK OF ELECTRIC SHOCK IS PRE­SENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANY-ING THE APPLIANCE.
IMPORTANT SAFEGUARDS
1. Read instructions-All the safety and operating instruc­tions should be read before the appliance is operated.
2. Retain Instructions-The safety and operating instruc­tions should be retained for future reference.
3. Heed Warnings-All warnings on the appliance and in the operating instructions should be adhered to.
4. Follow Instructions-All operating and use instructions should be followed.
5. Cleaning-Unplug TV from the wall outlet before clean­ing. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. EXCEPTION: A product that is meant for uninterrupt­ed service and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the appliance in the cleaning description otherwise required in item 5.
6. Attachments-Do not use attachments not recommended by the TV manufacturer as they may cause hazards.
7. Water and Moisture-Do not use this TV near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.
8. Accessories-Do not place this TV on an unstable cart, stand, tripod, bracket, or table. The TV may fall, caus­ing serious injury to someone, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the TV. Any mounting of the appliance should follow the manufacturer’s instructions and should use a mounting accessory recommended
by the manufacturer. An appliance and cart combina­tion should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.
9. Ventilation-Slots and openings in the cabinet and the back or bottom are provided for ventilation and to ensure reliable operation of the TV and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the TV on a bed, sofa, rug, or other similar sur­face. This TV should never be placed near or over a radiator or heat register. This TV should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufac­turers instructions have been adhered to .
10. Power Sources-This TV should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For TVs intended to operate from bat­tery power, or other sources, refer to the operating instructions.
11. Grounding or Polarization-This TV is equipped with a polarized alternating-current line plug(a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
12. Power-Cord Protection-Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.
13. Outdoor Antenna grounding-If an outside antenna or cable system is connected to the TV, be sure the anten­na or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA No. 70, provides information with respect to proper grounding of the mast and supporting struc­ture, grounding of the lead-in wire to an antenna dis­charge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding elec­trodes, and requirements for the grounding electrode. (Fig. A)
14. Lightning-For added protection for this TV receiver during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the TV due to lightning and power-line surges.
15. Power Lines-An outside antenna system should not be located in the vicinity of overhead power lines or other electric light of power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
16. Overloading-Do not overload wall outlets and exten­sion cords as this can result in a risk of fire or electric shock.
17. Object and Liquid Entry-Never push objects of any kind into this TV through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the TV.
18. Servicing-Do not attempt to service this TV yourself as opening or removing covers may expose you to dan­gerous voltage or other hazards. Refer all servicing to qualified service personnel.
19. Damage Requiring Service-Unplug this TV from the wall outlet and refer servicing to qualified service per­sonnel under the following conditions:
a. When the power supply cord or plug is damaged or
frayed.
b. If liquid has been spilled, or objects have fallen into
the TV.
c. If the TV has been exposed to rain or water. d. If the TV does not operate normally by following the
operating instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment of other controls may result in damage and will often require extensive work by a qualified techni­cian to restore the TV to its normal operation.
e. If the TV has been dropped or damaged in any way. f. When the TV exhibits a distinct change in perfor-
mance-this indicates a need for service.
20. Replacement Parts-When replacement parts are required, be sure the service technician uses replace­ment parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, injury to persons or other hazards.
21. Safety Check-Upon completion of any service or repairs to this TV, ask the service technician to perform routine safety checks to determine that the TV is in proper operating condition.
22. Heat-This TV product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
OPERATING CONTROLS AND FUNCTIONS
- FRONT PANEL - - REAR PANEL -
- REMOTE CONTROL -
1. HEADPHONE jack- To connect head-
phone (not supplied) for personal listening.
2. VIDEO (in) jack- Connect to the video
output jack of a video camera or VCR.
3. AUDIO L (in) jack- Connect to the left
channel audio output jack of a video camera or VCR. NOTE: The rear-panel AUDIO L (IN) jack is for mono input. The sound is heard from both speakers. Use this jack for monaural audio equipment to be hooked up.
4. AUDIO R (in) jack- Connect to the right
channel audio output jack of a video camera or VCR.
5. MENU button- Press to display the menu
on the TV screen.
6. VOLUME
/buttons- Press to control
the volume level. Press to determine the setting mode from the menu on the TV screen. (only the VOL button) Press to select or adjust from a particular menu. (for example: Language Selection, Channel Presetting, Closed Caption Selection, Picture Adjustment, V-CHIP Set Up)
7. CHANNEL /buttons- Press to select
memorized channel. NOTE:You MUST PRESET channels BEFORE using CHANNEL ▲/▼ buttons. (See CHANNEL PRESETTING) Press to select the setting mode from the menu on the TV screen. Press to select item you want to adjust in the picture control mode.
8. POWER button- Press to turn the TV ON
and OFF.
9. Infrared Sensor Window- Receives the
infrared control signals from the remote control unit.
10.MUTE button- Press the MUTE button to
turn off the sound portion of the TV pro­gram. (Volume level display turns LIGHT RED from LIGHT BLUE.) Press the MUTE button again or press the VOL(ume) ▲ or ▼ button to restore sound.
11. CHANNEL RETURN button- Press this
button to go back to the previously viewed channel. For example, pressing the CHAN­NEL RETURN button once will change channel display from CH 3 (present chan­nel) to CH 10 (previously viewed channel), and pressing it a second time will return from CH 10 to CH 3.
12.DISPLAY button- Press to display the
channel number on the screen. If you press it again, the channel number will disappear.
13.SLEEP button- Press the SLEEP button to
display the sleep timer and start the func­tion. The shut off time can be determined by the number of times you press the but­ton. (0, 10, 20, 30,..90, 0 minutes)
14.GAME button- Press to set the Game
mode and external input mode at the same time. Press the GAME button again to exit this mode.
15.CHANNEL NUMBER buttons- Press
two digits to directly access the desired channel. Remember to press a "0" before a single digit channel. +100 button- Press to select cable chan­nels higher than 99.
16.AC cord- Connect to a standard AC outlet
(120V/60Hz). NOTE: Unwrap the AC cord completely from the backcover before plugging the cord into an AC outlet.
17.ANT(enna). IN jack- Connect to an anten-
na, cable system, or satellite system.
EXTERNAL INPUT MODE
When using an external input signal (VCR or camcorder), connect the players audio/video output cables to the AUDIO IN/ VIDEO IN jacks of your TV. Then press the GAME button. For details, see USING THE GAME BUT­TON in PICTURE ADJUSTMENT section.
Loading...
+ 2 hidden pages