Page 1
ELECTRIC FIREPLACE HEATER
FAIRBANKS
Model: SRM850P-47BHO (CTC # 64-3546)
IMPORTANT:
PLEASE NOTE WH EN YOU OPEN THE CARTON, CAREFULLY CHECK
THE UNIT AND MAKE SURE THERE IS NO DAMAGE. IF YOU HAVE ANY
PROBLEMS WITH ASSEMBLING THE UNIT, WITH HOW THE VARIOUS
FUNCTIONS WORK OR WITH DAMAGE OR MISSING PARTS, PLEASE CALL
1-800-459-4409 (EST) IMMEDIATELY FOR SERVICE.
INSTRUCTION MANUAL
ATTENTION:
1. Find a location for the fireplace heater that is protected from direct sunlight.
2. Do not plug the unit into the power outlet before reading all instructions.
SAVE THESE INSTRUCTIONS FOR FUTURE USE.
8) Do not run cord under carpeting. Do not cover cord with throw rugs, runners,
or similar coverings. Arrange cord away from traffic area and where it will not
be tripped over.
9) To disconnect fireplace, turn controls to off, then remove plug from outlet.
10) Do not insert or allow foreign objects to enter any ventilation or exhaust
opening as this may cause an electric shock or fire, or damage the heater.
11) To prevent a possible fire, do not block air intakes or exhaust in any manner. Do
not use on soft surfaces, like a bed, where openings may become blocked.
12) A heater has hot and arcing or sparking parts inside. Do not use it in areas
where gasoline, paint, or flammable liquids are used or stored.
13) Use this fireplace heater only as described in this manual. Any other use not
recommended by the manufacturer may cause fire, electric shock, or injury to
persons.
14) Avoid the use of an extension cord because the extension cord may overheat
and cause a risk of fire. However, if you have to use an extension cord, the cord
shall be No.16AWG minimum size and rated not less than 1875 watts.
15) Caution: Do not plug this product into a receptacle controlled by a wall switch
or dimmer.
16) When storing or transporting the unit and cord, keep in a dry place, free from
excessive vibration and store so as to avoid damage.
CAUTION:
SYLVANIA is a registered trademark of OSRAM SYLVANIA, used under license.
IF YOU USE THIS HEATER IN CONJ UNCTION WITH A THERMAL CONTROL, A
PROGRAM CONTROLLER, A TIMER OR ANY OTHER DEVICE THAT SWITCHES
THE HEATER ON AUTOMATICALLY, REMEMBER TO OBSERVE ALL SAFETY
WARNINGS AT ALL TIMES. THE FIREPLACE HEATER HAS SAFETY OVERHEAT
PROTECTION. IF THE OVERHEAT PROTECTION TRIPS, SWITCH OFF ALL
SWITCH BUTTONS AND WAIT APPROXIMATELY 5 -10 MINUTES. IT SHOULD
RESET AUTOMATICALLY ONCE THE UNIT COOLS DOWN.
WARNING:
Procedures and techniques if not carefully followed will result in damage to the
equipment and will expose the user to the risk of serious injury, illness or death.
This electric fireplace heater is for use on 120 volts. The cord has a plug as shown
at A in illustration below. An adapter as shown at C is available for connecting
three-blade grounding-type plugs to two-slot receptacles. The green grounding
plug extending from the adapter must be connected to a permanent ground such
as a properly grounded outlet box. The adapter should not be used if a three-slot
grounded receptacle is available.
A 15 AMP circuit is required to operate this heater. If the breaker trips when the
heater is used then you may need to move the heater to another location or unplug
other appliances that are on the same circuit. If you require an extension cord use
one that is rated at 1875 watts.
IMPORTANT SAFETY INSTRUCTIONS
WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS SHOULD
ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,
AND INJURY TO PERSONS, INCLUDING THE FOLLOWING:
1) Read all instructions before using this electric fireplace heater.
2) This electric fireplace heater is hot when in use. To avoid burns, do not let bare
skin touch hot surfaces. The grill directly in front of the heater outlet becomes
hot during heater operation. Keep combustible materials, such as furniture,
pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) away from
the front of the unit and keep them away from the sides and rear.
3) Extreme caution is necessary when any heater is used by or near children or
individuals with disabilities and whenever the fireplace is left operating
and unattended.
4) Always unplug fireplace when not in use.
5) Do not operate any electric fireplace with a damaged cord or plug or after the
heater malfunctions, has been dropped or damaged in any manner.
6) Do not use outdoors.
7) This electric fireplace heater is not intended for use in bathrooms, laundry
areas and similar indoor locations. Never locate heater where it may fall into a
bathtub or other water container.
1
Page 2
NOTE:
DO NOT RETURN UNIT TO THE STORE BEFORE CALLING THE TOLL FREE NUMBER.
Do not dispose of you cartons until you are completely satisfied with your new
fireplace heater.
NOTE: Light bulbs may become loose during shipping. If the flame effect is dim or
does not work, please check that light bulb or bulbs are finger tight in socket. See
instructions for replacing bulb or bulbs.
ASSEMBLY INSTRUCTIONS
PARTS LIST:
Fireplace insert ......................................................................................................................1
A) Top panel .........................................................................................................................1
B) Base panel .......................................................................................................................1
C) Upper front panel ..........................................................................................................1
D) Lower front panel...........................................................................................................1
E) Left front panel ...............................................................................................................1
F) Right front panel.............................................................................................................1
G) Left side panel ................................................................................................................1
H) Right side panel ..............................................................................................................1
P) Connectors ......................................................................................................................2
Q) Large ‘L‘ brackets ............................................................................................................2
R) Nuts ..................................................................................................................................2
S) Washers ...........................................................................................................................2
T) Small screws ...................................................................................................................2
U) Medium KD screws ........................................................................................................6
W) KD screws ..................................................................................................................... 52
X) Plastic connectors.........................................................................................................14
Y) SELF REPAIR SET
Touch-up repair paint (bottle)
L shape bracket .....................................................................................................................2
Screws for L bracket .............................................................................................................8
Plastic Connector ..................................................................................................................1
KD Screws ..............................................................................................................................3
KD Nuts ..................................................................................................................................3
Z) WALL ANCHOR SAFETY CABLE
Wall Anchor ...........................................................................................................................1
Screw for wall anchor ..........................................................................................................1
Screw for mantle ...................................................................................................................1
Cable.......................................................................................................................................1
TOOLS REQUIRED: PH ILLIPS HEAD SCREWDRIVER and ADJUSTABLE WRENCH
MANTEL ASSEMBLY:
CAUTION: Place a piece of cardboard or protective sheet on the floor in order to
avoid scratching the decorative surface of your mantel during assembly. Please DO
NOT fully tighten the KD screws until all panels are assembled.
NOTE: Each plastic connector is pre-assembled (pre-drilled) on the specific panels
with 2 screws. If the KD screw(s) do not fit during assembly, loosen the 2 (pre-drilled)
screws to adjust the plastic connector until the KD screws are able to be installed.
Tighten all KD screws once all panels are assembled.
Step 1: Attach 10 plastic connectors [X] to left side panel [G] and right side panel [H] with
20 KD screws (2 screws for each connector). Attach 2 plastic connectors to left front
panel [E] and right front panel [F] with 4 KD screws. Attach 2 plastic connectors to upper
front panel [C] with 4 KD screws and 2 connectors [P] to upper front panel [C] with 4 KD
screws. See Fig. A.
2
Page 3
fig. A
Step 2: Attach left side panel [G] to left front panel [E] with 2 KD screws. Attach right
side panel [H] to right front panel [F] with 2 KD screws. See Fig. B.
fig. D
Step 5: Attach upper front panel [C] as shown in Fig. E with 6 KD screws.
fig. E
fig. B
Step 3: Attach left side panel [G] and left front panel [E] to base panel [B] with 2 KD screws.
Attach right side panel [H] and right front panel [F] to base panel [B] with 2 KD screws.
See Fig. C.
fig. C
Step 4: Attach lower front panel [D] to left and right front panels [E & F] with 2 KD screws as
shown in Fig. D.
Step 6: Attach top panel [A] as shown in Fig. F with 4 KD screws.
fig. F
Step 7: Attach 2 large ‘L‘ brackets [Q] to each sides of fireplace insert with washers [S],
and fixed by small screws [T] and nuts [R]. See Fig. G.
3
Page 4
fig. G
Step 8: Attach fireplace insert to the unit as shown in Fig. H, with 6 medium KD screws
[U]. [ 4 screws at the top of insert and 2 screws at the large ‘L‘ brackets ]
fig. H
WALL
OPERATION
After reading complete instructions, confirm all controls on fireplace are in the OFF
position. Plug the fireplace into a 15 AMP/120 Volt outlet. If the cord does not reach,
you may use an extension cord rated for a minimum of 1875 WATTS. Once the
fireplace insert has been properly connected to a grounded electrical outlet, it is ready
to operate.
OPERATION BY THE CONTROL PANEL
Step 9: Tighten all screws.
Step 10: Carefully move the assembled unit to the desired location. The fireplace
mantel should not be positioned in an area exposed to direct sunlight.
WALL ANCHOR SAFETY CABLE
The use of the wall anchor safety cable is highly recommended in order to reduce the
risk of the fireplace being tipped over accidentally. WARNING: This cable may reduce
possible risk of injury if the fireplace is improperly handled, but is not a substitute for
proper adult supervision. Children should not be left unattended near any heater.
1. Drill a 5/16 in (8 mm) hole in the wall. Insert the plastic wall anchor into the hole
and gently tap until the flange on the anchor is against the wall surface.
2. Position the back edge of the mantle close to the wall.
3. Attach the safety cable to the mantle using the screw for mantel.
4. Use the screw for wall to attach the other end of the safety cable to the wall.
5. Make sure all screws are tight.
ON/OFF: Press this button for main power function. The unit will beep and the indicator light will be on. Pressing again will stop the main power function.
FLAME/LOG: Press this button once for flame effect. The unit will be beep and the
indicator light will be ON. The bulbs for flame effect and log-set will be ON. To adjust
the flame intensity, hold down the button - the flame optics will go higher or lower.
Once you have found the desired setting, release the button. Pressing the button
again will stop the light function.
750 W: Press this button for low heat level. The unit will beep, the pilot light and
indicator light will be ON. The fireplace heater will give low heat level. Pressing once
again will stop the low heat level function.
1500 W: Press this button for high heat level. The unit will beep, the pilot light and
indicator light will be on. The fireplace heater will give high heat level. Pressing once
again will stop the high heat level function.
HEAT TEMPERATURE CONTROL KNOB: To adjust the temperature to your individual
requirements, turn the temperature control dial to the right (clockwise) to increase the
desired temperature and to the left (counter clockwise) to lower the temperature.
4
Page 5
May not be exactly as shown.
MAINTENANCE WARNING:
Disconnect power and unplug the power cord before attempting any maintenance or
cleaning to reduce the risk of fire, electric shock or damage to persons. The bulbs in
your unit can become extremely hot. Allow at least 10 minutes between turning off the
unit and removing the light bulbs to avoid the accidental burning of the skin.
RISK OF FIRE: DO NOT EXCEED THE RECOMMENDED BULB WATTAGE.
REMOTE CONTROL BATTERY REPLACEMENT
OPERATION BY THE REMOTE CONTROL
Plug in your electric fireplace and it will beep once, this means you have power and
your remote is ready to operate your electric fireplace.
ON/OFF: Press this button for main power function. The unit will beep and the
indicator light will be on. Pressing again will stop the main power function.
Once the heater is switched off, the indicator light will flash and the unit will keep
working with air flow for 5 more seconds.
FLAME/LOG: Press this button once for flame effect. The unit will be beep and the
indicator light will be ON. The bulbs for flame effect and log-set will be ON. To adjust
the flame intensity, hold down the button - the flame optics will go higher or lower.
Once you have found the desired setting, release the button. Pressing the button
again will stop the light function.
750 W: Press this button for low heat level. The unit will beep, the pilot light and
indicator light will be ON. The fireplace heater will give low heat level. Pressing once
again will stop the low heat level function.
1500 W: Press this button for high heat level. The unit will beep, the pilot light and
indicator light will be ON. The fireplace heater will give high heat level. Pressing once
again will stop the high heat level function.
Replace with 2 AAA batteries.
WARNING:
Do not mix old and new batteries. Do not mix alkaline, standard (Carbon-Zinc), or
rechargeable (Nickel Cadmium) batteries.
MAINTENANCE
MAINTENANCE WARNING:
Disconnect power and unplug the power cord before attempting any maintenance or
cleaning to reduce the risk of fire, electric shock or damage to persons. The bulbs in
your unit can become extremely hot. Allow at least 10 minutes between turning off the
unit and removing the light bulbs to avoid the accidental burning of the skin.
RISK OF FIRE: DO NOT EXCEED THE RECOMMENDED BULB WATTAGE.
REPLACING THE LIGHT BULBS
Step 1: Remove 14 screws on the back of fireplace and open the rear cover.
There are 2 larger screws and 12 smaller screws
Step 2: You will find 1 X 40W Type B-10 bulb under log-set bed.
Step 3: Loosen and remove the burnt out bulb and replace with new bulb.
Step 4: Close the rear cover. Secure the larger screws into the top left corner hole
and bottom right corner holes as shown in the diagram. Secure the 12 smaller
screws into the remaining holes. Make sure the screws are in the correct holes
and have been tightened.
Step 5: Plug in the unit.
5
Page 6
REPAIRS
If any problems are found with the original parts during mantel assembly such as
the panels cannot be installed with the plastic connector, try to solve by one of the
following methods:
Tools required: Electric drill, drill bits 3/4 inches (10 mm) or 1/16 inches (2 mm),
pencil, hammer, Philips screwdriver, safety goggles and gloves (if necessary).
WARNING: Wear goggles before you start drilling.
OPTION 1:
Use the spare KD nuts, KD screws and plastic connector.
1. Place the plastic connector on the mantel unit and mark the drill-holes as shown
in Fig. B.
Fig. B
REPAIR SET
TOUCH-UP REPAIR PAINT
1. Paint directly on the mantel unit if necessary. Fig. A.
2. Drill the holes with diameter 3/4 inches (10 mm) and depth 3/4 inches
the mantel. Each plastic connector needs 3 holes. See Fig. C.
Fig. C
3. Gently install the KD nuts into the drilled-holes with hammer as shown in Fig. D.
4. Attach the plastic connector and lock in place with KD screws as shown in Fig. E.
Fig. D
(10 mm) on
Fig. A
Fig. E
6
Page 7
OPTION 2:
Use the small ‘L’ brackets and screws.
1. Place the small ‘L’ bracket to the unit as shown and mark the drill-holes on the
mantel as shown in Fig. F.
Fig. F
2. Drill the holes with diameter 1/16 inches (2 mm) and depth 5/16 inches (8 mm) on
the mantel. Each small ‘L’ bracket needs 4 holes. See Fig. G.
Imported by
Quality Craft Ltd.
Laval, Quebec, Canada H7S 2G7
1-800-459-4409 (EST)
www.qualitycraft.com
Made in China
Fig. G
3. Attach the small ‘L’ bracket and lock in place with screws as shown in Fig. H.
Fig. H
CLEANING
To clean unit first turn off controls on unit and unplug the unit from power source. To
clean glass display panel, remove dust with clean dry cloth or to remove finger prints
and other marks, clean glass with clean damp cloth. Do not use abrasive cleaners or
spray liquids on glass display panel surface. Metal and metal painted parts should
be cleaned with damp cloth. Do not use abrasive cleaners or spray liquids on these
surfaces.
WARRANTY
Every electric fireplace heater is tested before it leaves the factory and it is guaranteed
for one year. If the unit should fail to operate correctly within one year from the date
of purchase, call customer service at 1-800-459-4409 (EST). We will, at our discretion
either repair or replace the unit. It will have to be returned to us freight prepaid and
we will return the repaired or replaced unit to you freight prepaid. The company’s
sole obligation is to repair or replace the unit.
This warranty is void if in the opinion of Quality Craft the unit has been tampered
with, altered, misused, damaged, abused or used with the wrong power source. Light
bulbs and remote batteries are not covered by this warranty. The warranty is for
homeowner use only and does not cover units used in commercial situations.
7
Loading...