This service manual supplement (EWD7003) contains only
the difference from the original model.
For all other data, see the original service manual for
DVL700D.
DVD PLAYER
EWD7003
IMPORTANT SAFETY NOTICE
Proper service and repair is important to the safe, reliable operation of all
Funai Equipment. The service procedures recommended by Funai and
described in this service manual are effective methods of performing
service operations. Some of these service special tools should be used
when and as recommended.
It is important to note that this service manual contains various CAUTIONS
and NOTICES which should be carefully read in order to minimize the risk of
personal injury to service personnel. The possibility exists that improper
service methods may damage the equipment. It also is important to
understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE.
Funai could not possibly know, evaluate and advice the service trade of all
conceivable ways in which service might be done or of the possible
hazardous consequences of each way. Consequently, Funai has not
undertaken any such broad evaluation. Accordingly, a servicer who uses a
service procedure or tool which is not recommended by Funai must first use
all precautions thoroughly so that neither his safety nor the safe operation
of the equipment will be jeopardized by the service method selected.
Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit.
If Main Fuse (F1001) is blown, check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
HOT CIRCUIT. BE CAREFUL.
AC1001
AC CORD
F1001
1A 250V
F
A V
L1001
LINE
FILTER
D1001, D1002
D1004, D1005
BRIDGE
RECTIFIER
Q1003Q1001
SWITCHING
CONTROL
SWITCHING
F
A V
CAUTION
FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,
REPLACE ONLY WITH THE SAME TYPE FUSE.
ATTENTION : POUR UNE PROTECTION CONTINUE LES RISQES
D'INCELE N'UTILISER QUE DES FUSIBLE DE MÊME TYPE.
RISK OF FIRE
"This symbol means fast operating fuse."
"Ce symbole reprèsente un fusible à fusion rapide."
T1001
2
4
-REPLACE FUSE AS MARKED.
11
D1006
SCHOTTKY
12
BARRIER
D1008
SCHOTTKY
13
BARRIER
D1015
D1030
14
RECTIFIER
15
16
Q1011
IC1002
+1.5V
REG.
NOTE :
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
EV+3.3V
P-ON+9V
EV+5V
P-ON+5V
P-ON+3.3V
Q1002
Q1004
Q1014
CN1001
1,2,3 EV+1.5V
4,5 EV+3.3V
14,15 EV+9V
13 P-ON+5V
17 P-ON+3.3V
19 PWRCON
FROM/TO
CN401
HOT
AV CBA
7
6
IC1001
ERROR
VOLTAGE DET
4
3
17
18
1
2
(SHUNT REGULATOR)
IC1006
REG
Q1016
Q1006
1-2-8
E57T0BLP1-2-7
SCHEMATIC DIAGRAMS / CBA’S AND TEST POINTS
Standard Notes
WARNING
Many electrical and mechanical parts in this chassis
have special characteristics. These characteristics
often pass unnoticed and the protection afforded by
them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage,
etc. Replacement parts that have these special safety
characteristics are identified in this manual and its
supplements; electrical components having such features are identified by the mark " # " in the schematic
diagram and the parts list. Before replacing any of
these components, read the parts list in this manual
carefully. The use of substitute replacement parts that
do not have the same safety characteristics as specified in the parts list may create shock, fire, or other
hazards.
Notes:
1. Do not use the part number shown on these drawings for ordering. The correct part number is
shown in the parts list, and may be slightly different
or amended since these drawings were prepared.
2. All resistance values are indicated in ohms
3
(K=10
3. Resistor wattages are 1/4W or 1/6W unless otherwise specified.
4. All capacitance values are indicated in µF
(P=10
5. All voltages are DC voltages unless otherwise
specified.
, M=106).
-6
µF).
1-3-1SC_FN1
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING
PAG ES :
1. CAUTION:
FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE
SAME TYPE FUSE.
F
A V
ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQES D'INCELE N'UTILISER QUE
DES FUSIBLE DE MÊME TYPE.
RISK OF FIRE-REPLACE FUSE AS MARKED.
This symbol means fast operating fuse.
Ce symbole represente un fusible a fusion rapide.
2. CAUTION:
Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F1001) is blown, first check to see that all components in the power supply circuit are not defective
before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the
power supply circuit to fail.
3. Note:
(1) Do not use the part number shown on the drawings for ordering. The correct part number is shown in the parts
list, and may be slightly different or amended since the drawings were prepared.
(2) To maintain original function and reliability of repaired units, use only original replacement parts which are
listed with their part numbers in the parts list section of the service manual.
4. Wire Connectors
(1) Prefix symbol "CN" means "connector" (can disconnect and reconnect).
(2) Prefix symbol "CL" means "wire-solder holes of the PCB" (wire is soldered directly).
5. Mode: SP
6. Voltage indications for PLAY and STOP mode on the schematics are as shown below:
5.0
2
3
5.0
(2.5)
Indicates that the voltage
is not consistent here.
PLAY mode
STOP mode
1
(Unit: Volt)
The same voltage for
both PLAY & STOP modes
7. How to read converged lines
1-D3
Distinction Area
3
AREA D3
Line Number
(1 to 3 digits)
2
AREA B1
Examples:
1. "1-D3" means that line number "1" goes to area "D3".
1
1-D3
2. "1-B1" means that line number "1" goes to area "B1".
ABCD
8. Test Point Information
: Indicates a test point with a jumper wire across a hole in the PCB.
1-B1
: Used to indicate a test point with a component lead on foil side.
: Used to indicate a test point with no test pin.
: Used to indicate a test point with a test pin.
1-3-2SC_FN2
DVD Main 1/3 Schematic Diagram
DVD MAIN 1/3
Ref No.Position
IC201B-1
IC202E-4
IC301D-3
IC461E-1
Q251C-2
Q252B-2
Q253C-2
Q254B-2
CN201A-3
CN301A-1
CN401F-3
CONNECTORS
ICS
TRANSISTORS
DATA(VIDEO+AUDIO)
FOCUS SERVO SIGNAL
TRACKING SERVO SIGNAL
SPINDLE SERVO SIGNAL
SLED SERVO SIGNAL
A4
A3
B4
B3
C4
C3
D4
D3
E4
E3
F4
F3
A2
A1
B2
B1
1-3-31-3-4
C2
C1
D2
D1
E2
E1
F2
F1
E57T0SCD1
DVD Main 2/3 Schematic Diagram
DVD MAIN 2/3
Ref No.Position
IC101H-4
CN204K-1
IC
CONNECTORS
VIDEO SIGNAL
FOCUS SERVO SIGNALDATA(VIDEO+AUDIO)
TRACKING SERVO SIGNAL
Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit.
If Main Fuse (F1001) is blown, check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
F
A V
CAUTION
FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,
REPLACE ONLY WITH THE SAME TYPE FUSE.
ATTENTION : POUR UNE PROTECTION CONTINUE LES RISQES
D'INCELE N'UTILISER QUE DES FUSIBLE DE MÊME TYPE.
RISK OF FIRE-REPLACE FUSE AS MARKED.
"This symbol means fast operating fuse."
"Ce symbole reprèsente un fusible à fusion rapide."
NOTE :
The voltage for parts in hot circuit is measured
using hot GND as a common terminal.
Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit.
If Main Fuse (F1001) is blown, check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
CAUTION
F
A V
FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,
REPLACE ONLY WITH THE SAME TYPE FUSE.
ATTENTION : POUR UNE PROTECTION CONTINUE LES RISQES
D'INCELE N'UTILISER QUE DES FUSIBLE DE MÊME TYPE.
RISK OF FIRE-REPLACE FUSE AS MARKED.
"This symbol means fast operating fuse."
"Ce symbole reprèsente un fusible à fusion rapide."
NOTE :
The voltage for parts in hot circuit is measured
using hot GND as a common terminal.
Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit.
If Main Fuse (F1001) is blown, check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
CAUTION
F
A V
FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,
REPLACE ONLY WITH THE SAME TYPE FUSE.
ATTENTION : POUR UNE PROTECTION CONTINUE LES RISQES
D'INCELE N'UTILISER QUE DES FUSIBLE DE MÊME TYPE.
RISK OF FIRE-REPLACE FUSE AS MARKED.
"This symbol means fast operating fuse."
"Ce symbole reprèsente un fusible à fusion rapide."
NOTE :
The voltage for parts in hot circuit is measured
using hot GND as a common terminal.
1-3-19
1-3-20
BE57S0F01013
FUNCTION CBA Top View
FUNCTION CBA Bottom View
1-3-21
1-3-22
BE57S0F01013
WAVEFORMS
WF1 Pin 5 of CN1601
VIDEO-Y0.2V20µsec
WF2 Pin 7 of CN1601
WF5
Pin 13 of CN1601
AUDIO-R
WF6
Pin 16 of CN1601
1V0.5msec
NOTE:
Input
CD: 1kHz PLAY
(WF4~WF6)
DVD: POWER ON (STOP) MODE
(WF1~WF3)
VIDEO-C0.2V20µsec
WF3 Pin 21 of IC1402
VIDEO-CVBS0.5V20µsec
WF4
Pin 11 of CN1601
SPDIF
1V0.1µsec
AUDIO-L
1V0.5msec
1-4-1
1-4-2
E57T0WF
WIRING DIAGRAM
VIDEO-Y
OUT
VIDEO-Cb
OUT
W1001
EV+1.5V11
VIDEO-Cr
OUT
EV+1.5V22
EV+3.3V44
EV+1.5V33
VIDEO
OUT
AUDIO-L
OUT
AUDIO-R
OUT
DIGITAL
AUDIO OUT
S-VIDEO
OUT
AV CBA
(BE57S0F01013)
CN1001
2222
EV+3.3V55
GND66
GND77
GND88
GND99
GND1010
GND1111
GND1212
P-ON+5V1313
EV+9V1414
EV+9V1515
FP-STB1616
P-ON+3.3V1717
FP-DIN1818
PWRCON1919
CN401
FP-DOUT2020
FP-CLK2121
REMOTE
AC CORD
W1601
JP2001JP2002
K21
1
KEY-22
2
NU3
3
NU4
4
KEY-45
5
KEY-36
6
KEY-17
7
K18
8
CN1601
AUDIO-L1111
A-L-MUTE1212
VIDEO-Cb33
VIDEO-Y55
VIDEO-Cr11
GND22
GND66
GND44
CN601
GND99
VIDEO-C77
A-MUTE1010
GND88
AUDIO-R1313
A-R-MUTE1414
AUDIO+5V1515
SPDIF1616
FUNCTION CBA
(BE57S0F01013)
FG
SENSOR
FG CBA
FG-IN
P-ON+3.3V(D)
123
TRAY-OUT
SP(-)
SP(+)
4
TRAY-OUT
TRAY-IN
5
6
GND
7
8 SL(-)
9 SL(+)
SLED
MOTOR
M
SPINDLE
MOTOR
M
DVD MAIN CBA UNIT
CN201CN301
GND
123456789
VREF
P-ON+5V
E
CBD
11 2 3 5 6 4 7
DETECTOR
A
F
CD/DVD
101112131415161718
PD-MONI
GND(LD)
CD-LD
DVD-LD
GND(DVD-PD)
GND(CD-PD)
TS(-)
FS
TS
FS(-)
FS(+)
19
TS(+)
20
CN204
ANALOG-MONITOR
1
2 GND
(NO CONNECTION)
TRAY-IN
PICK UP UNIT
DRIVE CBA
DVD MECHA
1-5-11-5-2
E57T0WI
MECHANICAL PARTS LIST
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read carefully the product safety notice in this service manual.
Don't degrade the safety of the product through
improper servicing.
NOTE:
Parts that are not assigned part numbers (---------) are
not available.
# have special characteristics important to safety.
Before replacing any of these components, read carefully the product safety notice in this service manual.
Don't degrade the safety of the product through
improper servicing.
NOTES:
1.Parts that are not assigned part numbers (---------)
are not available.
2.Tolerance of Capacitors and Resistors are noted
with the following symbols.
C.....±0.25%D.....±0.5%F.....±1%
G.....±2%J......±5%K.....±10%
M.....±20%N.....±30%Z.....+80/-20%
DVD MAIN CBA UNIT
Ref. No. DescriptionPart No.
DVD MAIN CBA UNITN79FCGUP
AV CBA ASSEMBLY
Ref. No. DescriptionPart No.
AV CBA ASSEMBLY
Consists of the following:
AV CBA
FUNCTION CBA
0VSA13623
----------
----------
AV CBA
Ref. No.DescriptionPart No.
AV C BA
Consists of the followings
CAPACITORS
C1001#METALLIZED FILM CAP. 0.01µF/275V K orCT2E103HJE05
#METALLIZED FILM CAP. 0.01µF/250V M orCT2E103MS037
#METALLIZED FILM CAP. 0.01µF/250V KCT2E103DC011
C1003ELECTROLYTIC CAP. 2.2µF/250V M orCA2E2R2S6009
C1007ELECTROLYTIC CAP. 1000µF/6.3V MCE0KMASDL102
C1010CERAMIC CAP.(AX) CH J 560pF/50VCA1J561TU008
C1013CERAMIC CAP.(AX) B K 3300pF/50VCA1J332TU011
C1014ELECTOLYTIC CAP. 1000µF/6.3V M(105°C)CE0KMASDH102
C1017CERAMIC CAP.(AX) Y M 0.01µF/16VCCA1CMT0Y103
C1018ELECTROLYTIC CAP. 100µF/6.3V MCE0KMASDL101
C1021CHIP CERAMIC CAP. B K 0.01µF/50VCHD1JK30B103
C1022CHIP CERAMIC CAP. B K 0.01µF/50VCHD1JK30B103
C1029CERAMIC CAP.(AX) X K 2200pF/16VCCA1CKT0X222
C1034ELECTROLYTIC CAP. 470µF/6.3V MCE0KMASDL471
----------
Ref. No.DescriptionPart No.
C1035ELECTROLYTIC CAP. 470µF/16V MCE1CMASDL471
C1036CHIP CERAMIC CAP. B K 0.01µF/50VCHD1JK30B103
C1037CHIP CERAMIC CAP. F Z 0.1µF/50VCHD1JZ30F104
C1038ELECTROLYTIC CAP. 470µF/6.3V MCE0KMASDL471
C1039CHIP CERAMIC CAP. F Z 0.1µF/50VCHD1JZ30F104
C1047FILM CAP.(P) 0.01µF/50V J orCMA1JJS00103
FILM CAP.(P) 0.01µF/50V JCA1J103MS029
C1048ELECTROLYTIC CAP. 220µF/16V MCE1CMASDL221
C1050ELECTROLYTIC CAP. 220µF/6.3V MCE0KMASDL221
C1201ELECTROLYTIC CAP. 10µF/16V MCE1CMASDL100
C1202ELECTROLYTIC CAP. 10µF/16V MCE1CMASDL100
C1205CHIP CERAMIC CAP. CH J 220pF/50VCHD1JJ3CH221
C1206CHIP CERAMIC CAP. CH J 220pF/50VCHD1JJ3CH221
C1207CHIP CERAMIC CAP. CH J 47pF/50VCHD1JJ3CH470
C1208CHIP CERAMIC CAP. CH J 47pF/50VCHD1JJ3CH470
C1221ELECTROLYTIC CAP. 10µF/16V MCE1CMASDL100
C1222ELECTROLYTIC CAP. 10µF/16V MCE1CMASDL100
C1223CHIP CERAMIC CAP. CH J 1000pF/50VCHD1JJ3CH102
C1224CHIP CERAMIC CAP. CH J 1000pF/50VCHD1JJ3CH102
C1245CHIP CERAMIC CAP. F Z 0.1µF/50VCHD1JZ30F104
C1246CHIP CERAMIC CAP. F Z 0.1µF/50VCHD1JZ30F104
C1247ELECTROLYTIC CAP. 470µF/6.3V MCE0KMASDL471
C1249ELECTROLYTIC CAP. 47µF/16V MCE1CMASDL470
C1351CHIP CERAMIC CAP. B K 0.1µF/25VCHD1EK30B104
C1353CHIP CERAMIC CAP. B K 1µF/10VCHD1AK30B105
C1354CHIP CERAMIC CAP. CH J 100pF/50VCHD1JJ3CH101
C1355CHIP RES.(1608) 1/10W 0 ΩRRXAZR5Z0000
C1358CHIP CERAMIC CAP. CH D 9pF/50VCHD1JD3CH9R0
C1394ELECTROLYTIC CAP. 47µF/6.3V MCE0KMASDL470
C1395ELECTROLYTIC CAP. 470µF/6.3V MCE0KMASDL471
C1402ELECTROLYTIC CAP. 470µF/6.3V MCE0KMASDL471
C1421CHIP CERAMIC CAP. B K 0.01µF/50VCHD1JK30B103
C1422CHIP CERAMIC CAP. B K 0.1µF/25VCHD1EK30B104
C1441CHIP CERAMIC CAP. B K 0.33µF/10VCHD1AK30B334
C1442ELECTROLYTIC CAP. 470µF/6.3V MCE0KMASDL471
C1461ELECTROLYTIC CAP. 1µF/50V MCE1JMASDL010
C1462ELECTROLYTIC CAP. 470µF/6.3V MCE0KMASDL471
C1481ELECTROLYTIC CAP. 1µF/50V MCE1JMASDL010
C1482ELECTROLYTIC CAP. 470µF/6.3V MCE0KMASDL471
C1521CHIP CERAMIC CAP. CH J 100pF/50VCHD1JJ3CH101
C1522ELECTROLYTIC CAP. 10µF/16V MCE1CMASDL100
C1523CHIP CERAMIC CAP. F Z 0.1µF/50VCHD1JZ30F104
C1524ELECTROLYTIC CAP. 100µF/6.3V MCE0KMASDL101
C1531CHIP CERAMIC CAP. B K 0.01µF/50VCHD1JK30B103
C1532ELECTROLYTIC CAP. 22µF/6.3V MCE0KMASDL220
C2004CHIP CERAMIC CAP. F Z 0.1µF/50VCHD1JZ30F104
C2011CHIP CERAMIC CAP. F Z 0.1µF/50VCHD1JZ30F104
C2012ELECTROLYTIC CAP. 100µF/6.3V MCE0KMASDL101
C2013CHIP CERAMIC CAP. CH J 1000pF/50VCHD1JJ3CH102
CONNECTORS
CN1001FMN CONNECTOR, TOP 22P 22FMN-BTKJCFNG22JG001
CN1601FMN CONNECTOR, TOP 16P 16FMN-BTK orJCFNG16JG001