Sylvania EN-ECU-G4-P3D User Manual

OSRAM and Logo are registered trademarks of OSRAM

GmbH.

Overview

www.sylvania.com/encelium

™

ENCELIUM

Energy Management System

Energy Control Unit

Wiring and Installation Manual

The Energy Control Unit (ECU) is a gateway that
interfaces to both IT equipment (servers, LAN, etc) and
field bus devices (luminaire controllers, sensors, wall
switches, etc). Communication with IT equipment and
other ECUs is achieved using the Ethernet port.
Additionally, two USB 2.0 ports are provided for data
transfer and back-up purposes.

The ECU provides operating power together with
communication signals via GreenBus IITM to the various
field bus devices of the system via eight GreenBus IITM communication channels.

The ECU makes each device addressable via GreenBus IITM (e.g. each light fixture can be individually dimmed and
turned on/off). Devices will obtain their addresses during the commissioning process and no actions are required
during installation.

The following model(s) are available:

Indoor Locations:

EN-ECU-G4-P3D

Important Safeguards

When using electrical equipment, basic safety precautions should always be followed including the following:

• READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

• Do not let power supply cords touch hot surfaces.

• Do not mount near gas or electric heaters.

• Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by

unauthorized personnel.

• The use of accessory equipment is not recommended by OSRAM Sylvania as it may cause an unsafe condition.

• Do not use this equipment for other than the intended use.

SAVE THESE INSTRUCTIONS

Page 1 of 4

76-015-DA 10/13

ENCELIUM and Polaris 3D are registered trademarks of OSRAM SYLVANIA, Inc
GreenBus II are trademarks of OSRAM SYLVANIA, Inc.
SEE THE WORLD IN A NEW LIGHT is a registered trademark of OSRAM SYLVANIA, Inc.

OSRAM and Logo are registered trademarks of OSRAM

GmbH.

GreenBus II™ Wiring

Communication Circuit (24VDC, Class 2)

GreenBus IITM is a low-cost, high reliability communication means to report sensor and wall switch information back
to the ENCELIUM Energy Management System and to obtain optimum brightness settings for each individual light
fixture from the system – optimized to result in minimum energy costs for any given building.

The GreenBus IITM wiring originates at an Energy
Control Unit (ECU) and propagates in a daisy-chain
or “T” fashion from module to module (or other
compatible equipment).

GreenBus IITM uses proprietary connectors and jacks for ease of installation only.

Maximum 100 total devices

GreenBus IITM is a proprietary standard. Connect to ENCELIUM Energy Management System only. Do not
connect to other circuits.

Connect to ENCELIUM Energy Management System only. Do not connect to other circuits.

GreenBus IITM must be laid out as per ENCELIUM EMS supplied drawing. If changes are required, determine an
optimum wiring path utilizing the supplied prefabricated cables, based on the position of light fixtures and sensors.
As the modules obtain power via the GreenBus IITM, the number of modules on each chain is limited. It is suggested
to leave room for future system upgrades and to limit the number of modules per chain to 100 units during initial
installation.

Energy Control Unit Installation

The output channels of the Energy Control Unit are Class 2 circuits.

To reduce the risk of electric shock, the power supply for the equipment has a grounding type plug that has a
third (grounding) pin. This plug will only fit into a grounding type outlet. If the plug does not fit into the outlet,
contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

Use only the power supply provided for this equipment. Damage or adverse functionality may occur if a
different power supply is used. If a replacement power supply is needed, please contact OSRAM Sylvania
Inc. Do not modify the power supply cable or connector.

The Energy Control Unit is intended for mounting in an electrical room where access will be by authorized
personnel only.

Page 2 of 4

76-015-DA 10/13

ENCELIUM and Polaris 3D are registered trademarks of OSRAM SYLVANIA, Inc
GreenBus II are trademarks of OSRAM SYLVANIA, Inc.
SEE THE WORLD IN A NEW LIGHT is a registered trademark of OSRAM SYLVANIA, Inc.

OSRAM and Logo are registered trademarks of OSRAM

GmbH.

Installation Notes

The Energy Control Unit shall be installed in dry, indoor locations ONLY. The Energy Control Unit shall be installed
into a Pollution Degree 2 (or better) environment.

The Energy Control Unit may be installed into a standard 19”
rack or mounted to a wall. A bracket is provided for rack
installations. Using the screws provided, affix the bracket
securely to the Energy Control Unit as shown.

If the Energy Control Unit is to be installed onto a wall
surface, use suitable screws to securely hold the unit. Install the unit with the input power, LAN, and GreenBus IITM
connections facing down. The control buttons shall be facing upward. This orientation will ensure adequate cooling
for the product while installed against a wall surface.

Troubleshooting

There are no user-serviceable parts inside of the Energy Control Unit. Please return the device to OSRAM Sylvania
Inc if service is required.

Energy Control Unit Wiring

Page 3 of 4

76-015-DA 10/13

ENCELIUM and Polaris 3D are registered trademarks of OSRAM SYLVANIA, Inc
GreenBus II are trademarks of OSRAM SYLVANIA, Inc.
SEE THE WORLD IN A NEW LIGHT is a registered trademark of OSRAM SYLVANIA, Inc.

OSRAM and Logo are registered trademarks of OSRAM

GmbH.

© 2013 OSRAM SYLVANIA 01

-

13

Regulatory Approvals

Note: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.

Modifications not expressly approved by the manufacturer could void the user's
authority to operate the equipment under FCC rules.

This equipment has been tested and found to comply with Industry Canada ICES-003
Issue 5 (CAN ICES-3 (A)/NMB-3(A)).

The contents of this Wiring and Installation Manual are subject to change without
notice.

Software End User License Agreement

This product includes third party software under license. See
www.encelium.com/licensing . All other software incorporated in or distributed with the
product is owned by and proprietary to Osram Sylvania Inc and licensed pursuant to
the terms of Osram Sylvania’s end user license agreement.

United States
OSRAM SYLVANIA

100 Endicott Street
Danvers, MA 01923
1-800-LIGHTBULB

Trade
Phone: [phone]
Fax: [phone]

National Accounts
Phone: [phone]
Fax: [phone]

OEM/Special Markets
Phone: [phone]
Fax: [phone]

Retail
Phone: [phone]
Fax: [phone]

SYLVANIA Lighting Services
Phone: [phone]
Fax: [phone]

Display/Optic
Phone: [phone]
Fax: [phone]

Canada
OSRAM SYLVANIA LTD.

2001 Drew Road
Mississauga, ON L5S 1S4
1-800-LIGHTBULB

Trade
Phone: [phone]
Fax: [phone]

OEM/Special
Markets/Display/Optic

Phone: [phone]
Fax: [phone]

Retail
Phone: [phone]
Fax: [phone]

SYLVANIA Lighting Services
Phone: [phone]
Fax: [phone]

Mexico
OSRAM MEXICO

Tultitlan/Edo de Mexico
Phone: [phone]

ENCELIUM® Products
United States

Phone: [phone]
Fax: [phone]

Canada
Phone: [phone]
Fax: [phone]

www.sylvania.com

/Sylvania

/sylvania

Page 4 of 4

76-015-DA 10/13

ENCELIUM and Polaris 3D are registered trademarks of OSRAM SYLVANIA, Inc
GreenBus II are trademarks of OSRAM SYLVANIA, Inc.
SEE THE WORLD IN A NEW LIGHT is a registered trademark of OSRAM SYLVANIA, Inc.