Sylvania ZC320SL8, E7E2AUD Schematic

Download

Page 1

SERVICE MANUAL

DVD RECORDER

ZC320SL8

Page 2

IMPORTANT SAFETY NOTICE

Proper service and repair is important to the safe, reliable operation of all Funai Equipment. The service procedures recommended by Funai and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended.

It is important to note that this service manual contains various CAUTIONS and NOTICES which should be carefully read in order to minimize the risk of personal injury to service personnel. The possibility exists that improper service methods may damage the equipment. It also is important to understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE. Funai could not possibly know, evaluate and advice the service trade of all conceivable ways in which service might be done or of the possible hazardous consequences of each way. Consequently, Funai has not undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not recommended by Funai must first use all precautions thoroughly so that neither his safety nor the safe operation of the equipment will be jeopardized by the service method selected.

TABLE OF CONTENTS

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1-1

Laser Beam Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2-1

Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3-1

Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4-1

Cabinet Disassembly Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5-1

How to Initialize the DVD Recorder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6-1

Firmware Renewal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7-1

Function Indicator Symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-8-1

Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9-1

Schematic Diagrams / CBA’s and Test Points. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-10-1

Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-11-1

Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12-1

System Control Timing Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13-1

IC Pin Function Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14-1

Lead Identifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15-1

Exploded Views. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16-1

Mechanical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-17-1

Electrical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-18-1

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

Page 3

SPECIFICATIONS

Item Conditions Unit Nominal Limit

1. VIDEO

1-1. Video Output 75 Ω load Vp-p 1.0 1-2. S-Video Output Y (Luminance) 75 Ω load Vp-p 1.0 C (Chrominance) 75 Ω load Vp-p 0.286 1-3. Component Output Y (Luminance) 75 Ω load Vp-p 1.0 Cb (U) 75 Ω load Vp-p 0.7 Cr (V) 75 Ω load Vp-p 0.7

2. AUDIO

2-1. Output Level Vrms 2.0 2-2. Frequency Response DVD-VIDEO LPCM fs = 96 kHz Hz 20 - 44 k

fs = 48 kHz Hz 20 - 20 k Audio CD fs = 44.1 kHz Hz 20 - 20 k 2-3. Signal/Noise Ratio DVD-VIDEO LPCM dB 120 CD dB 120 REC & Playback Input: 2 Vrms, Rec Speed: XP dB 90 2-4. Dynamic Range DVD-VIDEO LPCM dB 90 CD dB 90 REC & Playback Input: 2 Vrms, Rec Speed: XP dB 90 2-5. THD+N 1 kHz, 0 dB DVD-VIDEO LPCM % 0.01 CD % 0.01 REC & Playback Input: 2 Vrms, Rec Speed: XP % 0.01

Notes:

1. All Items are measured without pre-emphasis unless otherwise specified.

2. Power supply: AC 120 V, 60 Hz

3. Load imp.: 100 kΩ

4. Room ambient: 5 °C ~ 40 °C

1-1-1 E7E2ASP

Page 4

LASER BEAM SAFETY PRECAUTIONS

This DVD player uses a pickup that emits a laser beam.

Do not look directly at the laser beam coming from the pickup or allow it to strike against your skin.

The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep your eyes at least 30 cm away from the pickup lens when the diode is turned on. Do not look directly at the laser beam.

CAUTION: Use of controls and adjustments, or doing procedures other than those specified herein, may result in hazardous radiation exposure.

Drive Mechanism Assembly

Laser Beam Radiation

Laser Pickup

Turntable

Location: Inside Top of DVD mechanism.

1-2-1 RL4NLSP

Page 5

IMPORTANT SAFETY PRECAUTIONS

Product Safety Notice

Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection, nor can the protection they give necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by a # on schematics and in parts lists. Use of a substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire, and/or other hazards. The Product’s Safety is under review continuously and new instructions are issued whenever appropriate. Prior to shipment from the factory, our products are carefully inspected to confirm with the recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.

Precautions during Servicing

A. Parts identified by the # symbol are critical for

safety. Replace only with part number specified.

B. In addition to safety, other parts and assemblies

are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements. Examples: RF converters, RF cables, noise blocking capacitors, and noise blocking filters, etc.

C. Use specified internal wiring. Note especially:

1) Wires covered with PVC tubing

2) Double insulated wires

3) High voltage leads

D. Use specified insulating materials for hazardous

live parts. Note especially:

1) Insulation tape

2) PVC tubing

3) Spacers

4) Insulators for transistors

E. When replacing AC primary side components

(transformers, power cord, etc.), wrap ends of wires securely about the terminals before soldering.

F. Observe that the wires do not contact heat

producing parts (heat sinks, oxide metal film resistors, fusible resistors, etc.).

G. Check that replaced wires do not contact sharp

edges or pointed parts.

H. When a power cord has been replaced, check that

5 - 6 kg of force in any direction will not loosen it.

I. Also check areas surrounding repaired locations. J. Be careful that foreign objects (screws, solder

droplets, etc.) do not remain inside the set.

K. When connecting or disconnecting the internal

connectors, first, disconnect the AC plug from the AC outlet.

1-3-1 DVDN_ISP

Page 6

Safety Check after Servicing

Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts, and wires have been returned to their original positions. Afterwards, do the following tests and confirm the specified values to verify compliance with safety standards.

1. Clearance Distance

When replacing primary circuit components, confirm specified clearance distance (d) and (d’) between soldered terminals, and between terminals and surrounding metallic parts. (See Fig. 1)

Table 1: Ratings for selected area

Chassis or Secondary Conductor

Primary Circuit

AC Line Voltage Clearance Distance (d), (d’)

120 V ≥ 3.2 mm (0.126 inches)

Note: This table is unofficial and for reference only. Be

sure to confirm the precise values.

2. Leakage Current Test

Confirm the specified (or lower) leakage current between B (earth ground, power cord plug prongs) and externally exposed accessible parts (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.) is lower than or equal to the specified value in the table below.

Measuring Method (Power ON):

Insert load Z between B (earth ground, power cord plug prongs) and exposed accessible parts. Use an AC voltmeter to measure across the terminals of load Z. See Fig. 2 and the following table.

d' d

Fig. 1

Exposed Accessible Part

AC Voltmeter (High Impedance)

Earth Ground

Power Cord Plug Prongs

Table 2: Leakage current ratings for selected areas

AC Line Voltage Load Z Leakage Current (i) Earth Ground (B) to:

120 V

Note: This table is unofficial and for reference only. Be sure to confirm the precise values.

0.15 µF CAP. & 1.5 kΩ RES. Connected in parallel

i ≤ 0.5 mA Peak Exposed accessible parts

1-3-2 DVDN_ISP

Fig. 2

Page 7

STANDARD NOTES FOR SERVICING

Circuit Board Indications

1. The output pin of the 3 pin Regulator ICs is indicated as shown.

Top View

Out

2. For other ICs, pin 1 and every fifth pin are indicated as shown.

Pin 1

3. The 1st pin of every male connector is indicated as shown.

Pin 1

Input

Bottom View

Pb (Lead) Free Solder

When soldering, be sure to use the Pb free solder.

How to Remove / Install Flat Pack-IC

1. Removal

With Hot-Air Flat Pack-IC Desoldering Machine:

1. Prepare the hot-air flat pack-IC desoldering machine, then apply hot air to the Flat Pack-IC (about 5 to 6 seconds). (Fig. S-1-1)

Fig. S-1-1

Instructions for Connectors

1. When you connect or disconnect the FFC (Flexible Foil Connector) cable, be sure to first disconnect the AC cord.

2. FFC (Flexible Foil Connector) cable should be inserted parallel into the connector, not at an angle.

FFC Cable

Connector

CBA

* Be careful to avoid a short circuit.

2. Remove the flat pack-IC with tweezers while applying the hot air.

3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)

4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)

CAUTION:

1. The Flat Pack-IC shape may differ by models. Use an appropriate hot-air flat pack-IC desoldering machine, whose shape matches that of the Flat Pack-IC.

2. Do not supply hot air to the chip parts around the flat pack-IC for over 6 seconds because damage to the chip parts may occur. Put masking tape around the flat pack-IC to protect other parts from damage. (Fig. S-1-2)

1-4-1 DVDN_SN

Page 8

3. The flat pack-IC on the CBA is affixed with glue, so be careful not to break or damage the foil of each pin or the solder lands under the IC when removing it.

With Soldering Iron:

1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3)

CBA

Masking Tape

Tweezers

Hot-air Flat Pack-IC Desoldering Machine

Flat Pack-IC

Fig. S-1-2

Flat Pack-IC

Desoldering Braid

Soldering Iron

Fig. S-1-3

2. Lift each lead of the flat pack-IC upward one by one, using a sharp pin or wire to which solder will not adhere (iron wire). When heating the pins, use a fine tip soldering iron or a hot air desoldering machine. (Fig. S-1-4)

Sharp Pin

Fine Tip Soldering Iron

4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)

Fig. S-1-4

1-4-2 DVDN_SN

Page 9

With Iron Wire:

1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3)

2. Affix the wire to a workbench or solid mounting point, as shown in Fig. S-1-5.

3. While heating the pins using a fine tip soldering iron or hot air blower, pull up the wire as the solder melts so as to lift the IC leads from the CBA contact pads as shown in Fig. S-1-5.

4. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)

5. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)

Note: When using a soldering iron, care must be

taken to ensure that the flat pack-IC is not being held by glue. When the flat pack-IC is removed from the CBA, handle it gently because it may be damaged if force is applied.

Hot Air Blower

2. Installation

1. Using desoldering braid, remove the solder from the foil of each pin of the flat pack-IC on the CBA so you can install a replacement flat pack-IC more easily.

2. The “●” mark on the flat pack-IC indicates pin 1. (See Fig. S-1-7.) Be sure this mark matches the 1 on the PCB when positioning for installation. Then presolder the four corners of the flat pack-IC. (See Fig. S-1-8.)

3. Solder all pins of the flat pack-IC. Be sure that none of the pins have solder bridges.

Example :

Pin 1 of the Flat Pack-IC is indicated by a " " mark.

Fig. S-1-7

To Solid Mounting Point

CBA

Tweezers

Iron Wire

Soldering Iron

Fig. S-1-5

Fine Tip Soldering Iron

Flat Pack-IC

Presolder

Flat Pack-IC

CBA

Fig. S-1-8

Fig. S-1-6

1-4-3 DVDN_SN

Page 10

Instructions for Handling Semiconductors

Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work.

1. Ground for Human Body

Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.

2. Ground for Workbench

Be sure to place a conductive sheet or copper plate with proper grounding (1 MΩ) on the workbench or other surface, where the semi-conductors are to be placed. Because the static electricity charge on clothing will not escape through the body grounding band, be careful to avoid contacting semi-conductors with your clothing.

1MΩ

CBA

Grounding Band

1MΩ

CBA

Conductive Sheet or Copper Plate

1-4-4 DVDN_SN

Page 11

CABINET DISASSEMBLY INSTRUCTIONS

1. Disassembly Flowchart

This flowchart indicates the disassembly steps to gain access to item(s) to be serviced. When reassembling, follow the steps in reverse order. Bend, route, and dress the cables as they were originally.

[1] Top Cover

[2] Front Assembly

[3] SW CBA

[4] DVD Mechanism & DVD Main CBA Assembly

[5] Power Supply CBA

[6] Rear Panel

[7] AV CBA

[8] Front Bracket

2. Disassembly Method

Note:

(1) Identification (location) No. of parts in the figures (2) Name of the part (3) Figure Number for reference (4) Identification of parts to be removed, unhooked,

unlocked, released, unplugged, unclamped, or desoldered. P = Spring, L = Locking Tab, S = Screw, CN = Connector * = Unhook, Unlock, Release, Unplug, or Desolder e.g. 2(S-2) = two Screws (S-2), 2(L-2) = two Locking Tabs (L-2)

(5) Refer to “Reference Notes.”

Reference Notes

1. CAUTION 1: Locking Tabs (L-1) and (L-2) are fragile. Be careful not to break them.

[1] Top Cover

(S-1)

ID/

Loc.

No.

[1] Top Cover D1 6(S-1) ---

[2]

[3] SW CBA D2 *2(L-3) ---

[4]

[5]

[6] Rear Panel D5 (S-6), 6(S-7) --[7] AV CBA D5 5(S-8) ---

[8]

↓

(1)

Part

Front Assembly

DVD Mechanism & DVD Main CBA Assembly

Power Supply CBA

Front Bracket

↓

(2)

Fig.

No.

*5(L-1), *3(L-2),

*CN1061

4(S-3), (S-4),*CN101, *CN701, Locking Card

Spacers, M-PCB Plate Earth

D4 4(S-5), *CN1060 ---

D5 (S-9) ---

↓

(3)

Removal

Remove/*Unhook/

Unlock/Release/

Unplug/Desolder

↓

(4)

Note

---

↓

(5)

(S-1)

Fig. D1

1-5-1 E7E2ADC

Page 12

(S-5)

(L-1)

(L-2)

(S-3)

CN1061

(L-1)

(L-3) (L-2)

[2] Front Assembly

(S-4)

M-PCB Plate Earth

(S-3)

[3] SW CBA

(L-1)

Fig. D2

[4] DVD Mechanism & DVD Main CBA Assembly

[5] Power Supply CBA

CN1060

Fig. D4

(S-8)

[7] AV CBA

Locking Card Spacer

CN101

CN701

Locking Card Spacer

Fig. D3

[8] Front Bracket

(S-6)

[6] Rear Panel

(S-9)

Fig. D5

(S-7)

1-5-2 E7E2ADC

Page 13

3. How to Eject Manually

Note: When rotating the gear, be careful not to damage the gear.

1. Remove the Top Cover.

2. Rotate the gear in the direction of the arrow manually as shown below until the tray descends.

3. Pull the tray out manually and remove a disc.

View for A

Rotate this gear in the direction of the arrow

1-5-3 E7E2ADC

Page 14

HOW TO INITIALIZE THE DVD RECORDER

To put the program back at the factory-default, initialize the DVD recorder as the following procedure.

1. Turn the DVD recorder on.

2. Confirm that no disc is loaded or that the disc tray is open. To put the DVD recorder into the Version display mode, press [CM SKIP], [1], [2], and [3] buttons on the remote control in the order. Fig. a appears on the screen.

*1: " *2: Firmware Version differs depending on the models, and this indication is one example.

" differs depending on the models.

*******

F/W VERSION DISP

MODEL NAME :

FE VERSION : BE VERSION : TT VERSION :

LD ADJUSTMENT : DISC ADJUSTMENT :

DEFAULT SETTING : ENTER EXIT : RETURN

*****

R40_005_082 RL4F10210S1E T40015RDU

OK OK

Fig. a Version Display Mode Screen

3. Press [ENTER] button, then the DVD recorder starts initializing. When the initializing is completed, the DVD recorder exits the Version display mode and turns off the power automatically.

* To move into the Normal mode from the

Version display mode, press [RETURN] button on the remote control instead of [ENTER] button.

* When [POWER] button is pressed before

[ENTER] button is pressed, the DVD recorder exits the Version display mode, then the power turns off.

1-6-1 E7E2ANT

Page 15

FIRMWARE RENEWAL MODE

1. Turn the power on and remove the disc on the tray.

2. To put the DVD recorder into version up mode, press [CM SKIP], [6], [5], and [4] buttons on the remote control unit in the order. Then the tray will open automatically. Fig. a appears on the screen and Fig. b appears on the VFD.

* Firmware Version differs depending on the models, and this indication is one example.

Firm Update Mode

Please insert a disc.

Fig. a Version Up Mode Screen

Fig. b VFD in Version Up Mode

ver. RL4F10210S1E

Current F/W version is displayed.

4. Select the firmware version pressing arrow buttons, then press [ENTER]. Fig. d appears on the screen and Fig. e appears on the VFD. The DVD recorder starts updating.

About VFD indication of Fig. e:

1) When Fig. d is displayed on the screen, “F-UP”

is displayed on the VFD.

2) When “Firmware Updating... XX% Complete.”

is displayed on the screen, “10210” is displayed on the VFD.

* Firmware Version differs depending on the models, and this indication is one example.

Firm Update Mode ver. RL4F10210S1E

(*1)

File Loading...

Fig. d Programming Mode Screen

3. Load the disc for version up. Fig. c appears on the screen. The file on the top is highlighted as the default. When there is only one file to exist, Step 4 will start automatically.

* Firmware Version differs depending on the models, and this indication is one example.

Firm Update Mode ver. RL4F10210S1E

Disc name is displayed.

VOL_200703250934

1 RL4F10210S1E 2 RL4F10211S1E 3 RL4F10212S1E 4 RL4F10213S1E

Fig. c Update Disc Screen

Files included in the disc are displayed.

1 / 1

Fig. e VFD in Programming Mode (Example)

The appearance shown in (*1) of Fig. d is described as follows.

No. Appearance State

1 File Loading... Sending files into the memory

Firmware

Updating...

Writing new version data

XX% Complete. Firmware

--Update Failure

Failed in updating

5. After updating is finished, the tray opens automatically. At this time, no button is available.

6. Pull out the AC code once, then insert it again.

1-7-1 E7E2AFW

Page 16

FUNCTION INDICATOR SYMBOLS

Note: If an error occurs, a message with the error number appears on the screen.

Recording Error

Message Solution

Can not record on this disc.

This program is not allowed to be recorded.

This disc is protected and not recordable.

You cannot record on this disc as Power Calibration Area is full.

Insert the recordable disc, and ensure the disc status satisfies the recording requirements.

You cannot record copy prohibited programs.

Release the disc protect setting in the Disc Setting menu.

Error message

E35

Error

No.

1 An error occurs during data reading. -

4 An error occurs with OPC. 5 During recovery in a record. -

7 An error occurs in a format. 8 It cannot start an encode. -

13 It is a reply that “ATAPI is not readable.” -

16 An error occurs in Finalize Close. 17 An error occurs in Rec Stop Close. 18 An error occurs in PCA Full (DVD_R). 19 Safety Stop occurs during editing. 20 High Speed Disc. 2 21 The disc is not formatted. 5 22 Disc Error has occurred. 3

25 During the Macrovision picture input. 11 26 During the CGMS picture input. 12

29 Disc Protected Disc. 6

Error No.

Error Description Priority

There is no reply for 15 seconds in Test Unit Ready.

Cannot write the data after trying three times.

An error occurs even if recovery has been tried three times.

NV_PCK/RDI_PCK is not in encoded data.

Encode Pause condition continued for 10 minutes.

Encode Pause condition continued in normal REC condition for 10 minutes.

Difference in the address and can not get StreamID of RDI/VIDEO.

Cannot write the data after recovering SMALL VMGI.

Cannot write the data after DVD-R Reverse Track.

The disc except DVD-R/RW or finalized DVD-R.

1-8-1 E7EAAFIS

Page 17

Message Solution

Disc is full. (No area for new recording)

You cannot record on this disc as Power Calibration Area is full.

This disc is already finalized.

Can not record on this disc. Repeat the same operation.

You cannot record more than 49 titles on the disc.(The maximum is 49.)

You cannot record more than 254 chapters on the disc.(The maximum is 254.)

This program is not recordable in +VR mode.

The disc has no recording compatibility. Set “Make Recording Compatible” to “ON” to convert the disc.

Insert the recordable disc with enough recording space.

Insert a new disc. 35 PCA is Full. (in REC start) 4

Release the finalizing for this disc.

Delete unnecessary titles. 43 Its recording capacity has been reached. 9

Delete unnecessary chapter marks.

You cannot record copy prohibited programs.

Set “Make Recording Compatible” to “ON” to rewrite the menu, after that you will record to disc.

Error

No.

Error Description Priority

30 No avilable recording space. 10

36 It is finalized. (Video Format Disc) 8

37 Access to Memory Area range outside. 38 Sector Address is wrong. 39 BUP writing error of chapter editing. -

44 The 254 chapter has been reached. 10

45 During the CGMS picture input. 12

Trying to record onto the +VR formatting

disc that had been recorded by the other recorder.

If an error occurs during the timer recording, one of the following error numbers (40 to 42) or the above error messages (error number: 1 to 39 and 43 to 46) is displayed on the recording menu after timer recording. (Once the screen of the program line is exited, the program line for the error will be cleared.) (No Error Message is displayed for the error No. 40 ~ 42.)

mer Programming

z MON JAN/01 2:00AM

JANE30 PM PM E1

Error

No.

41 Power failed -

1 / 1

Error Description Priority

- Some portion has not been recorded because of program overlapping.

- Recording did not start at the start time.

A program with the error number is grayed out and asterisked on the timer programming list.

Message Solution

Error message is not displayed.

error number

- Set the timer programming correctly.

- Set the timer programming before the start time.

Turn the power on and set the clock correctly then set timer programming again.

Insert the recordable disc. 42 No disc when recording -

1-8-2 E7EAAFIS

Page 18

BLOCK DIAGRAMS

System Control Block Diagram

KEY SWITCH

Q1501

IC1502

EV+3.3V

RESET

1 2

RESET

P-DOWN

EV+5V

Q1502

C1501

VCC

(BACKUP CAPACITOR)

VFD

FL2001

GRID

(VFD DRIVER)

CLK

DIN

IC2001

485049

FL-DIN

FL-SCL

STB

FL-STB

REMOTE

RE2001

SEGMENT

SENSOR

REMOTE

CN1062

KEY-1

CN1061

KEY-1

KEY-2

OPEN/CLOSE

SW3011

KEY-2

IC1501

(SUB MICRO CONTROLLER)

POW-SW

REG-CONT

26 REG-CONT2

POW-SW

REG-CONT

REG-CONT2

TO POWER SUPPLY

BLOCK DIAGRAM

PWSW

VIDEO-SW1

42 VIDEO-SW2

43 VIDEO-SW3

VIDEO-SW1

VIDEO-SW2

VIDEO-SW3

TO VIDEO

BLOCK DIAGRAM

44 VIDEO-MUTE

POFF-SELECT

VIDEO-MUTE

AUDIO-SW1

AUDIO-SW2

37 POFF-SELECT

Q1511

AUDIO-SW1

AUDIO-SW2

POFF-SELECT

TO AUDIO

BLOCK DIAGRAM

X OUT

X1501

8MHz

X IN

RESONATOR

XC OUT

32.768KHz

X1502

XC IN

X'TAL

EV+2.8V

+1.2V

IC106

P-ON+1.2V

REGULATOR

111V2CONT

CN101 CN1051

IC107

RESETEV+2.8V

IC101

(MAIN MICRO CONTROLLER)

SUB-RXD

SYS-RESET

2219182029

CN1101

27 27SYS-RESET

30 30SUB-RXD

CN701

V25

R25

SUB-RXD

SYS-RESET

SUB-TXD

SUB-SCLK

RDY

28 28SUB-TXD

26 26SUB-SCLK

29 29RDY

P22

W26

RDY

SUB-TXD

SUB-SCLK

X501

27MHz

X'TAL

CLK 27 IN

AV CBA SW CBA

IC501

DVD MAIN CBA UNIT

1-9-1

E7E2ABLS

Page 19

Digital Signal Process Block Diagram

VIDEO-C

VIDEO-Y(I/P)

D/A

VIDEO

REC VIDEO SIGNAL PB VIDEO SIGNAL REC AUDIO SIGNAL PB AUDIO SIGNAL

VIDEO-Pr/Cr

VIDEO-Pb/Cb

A5,B5-B7

D/A

ENCODER

VIDEO

I/F

D6,D7

,C6,C7,

TO VIDEO

BLOCK

DIAGRAM

/CVBS

VIDEO-Y

VIDEO-C

10813

A/D

DECODER A/D

DECODER

IC701 (VIDEO DECODER)

45-50

39-44

U2,U3,V1

P3,T3,T5,

U4,W1,W3,

Y2,AA1,AA2

AUDIO (L)-OUT

AUDIO (R)-OUT

D/A

SPDIF

D/A

TO AUDI O

BLOCK

DIAGRAM

BCK

SYSCLK

U24

LRCK

DATA

DVD-AUDIO-MUTE

T23

DVD-AUDIO-MUTE

AIMS

Y26

E12

AUDIO

I/F

(MAIN MICRO CONTROLLER)

IC101

IC201

RF/

ERROR AMP

CN201

LPC

TILT

PICK

IC301

TRACKING

-UP

FOCUS

MOTOR

DRIVER

BACK-END

DIGITAL

SIGNAL

FRONT-END

DIGITAL

SIGNAL

PROCESS

P-ON+3.3V

TRAY OPEN

IC202

CN301

CN1001

OP AMP

IC302

MOTOR

DRIVER

IC104 (FLASH MEMORY)

CN1002

FLASH MEMORY

DDR SDRAM

IC102 (DDR2 SDRAM)

DVD MAIN CBA UNIT

RELAY CBA

DVD MECHANISM

1-9-2

SLED

MOTOR

SPINDLE

MOTOR

E7E2ABLD

Page 20

Video Block Diagram

TO SYSTEM CONTROL

BLOCK DIAGRAM

IC1022

(INPUT SELECT)

POFF-SELECT

REC VIDEO SIGNAL PB VIDEO SIGNAL

JK2101

3 4

S-VIDEO

IN2

CONTROL

FRONT

LOGIC

JK2102

VIDEO-SW1

22 23

VIDEO-IN2

TO SYSTEM CONTROL

BLOCK DIAGRAM

VIDEO-SW2

VIDEO-SW3

REAR

BUFFER

Q1601

SW CTL

C1231

WF3

JK2202

S-VIDEO OUT

3 4

VIDEO-OUT

JK2201

DRIVER

8dB

2dB

AMP

-6dB

LPF DRIVER

4dB

AMP

IC1401 (VIDEO DRIVER)

AMP

VIDEO-Y

JK2203

2dB

LPF DRIVER

4dB

OUT

AMP

VIDEO-Pb/Cb

OUT

2dB

AMP

2dB

LPF DRIVER

4dB

AMP

4dB

VIDEO-Pr/Cr

OUT

AMP

LPF DRIVER

MUTE

AMP

IC1301

(VIDEO INPUT SELECT)

VIDEO-MUTE

JK2105

S-VIDEO

IN1

3 4

BIAS

(VIDEO DRIVER)

6dB

IC1021

131915

MUTE

LPF

JK2106

MUTE

VIDEO-IN1

VIDEO1

VIDEO2

2214

MUTEC2C1

LPF

WF5

WF4

WF1 WF2

CN1101

CN701

VIDEO-Y(I/P)

BUFFER

Q1304

BUFFER

Q1303

VIDEO-Y(I/P)-OUT

VIDEO-C-OUT

VIDEO-Pb/Cb-OUT

VIDEO-Pr/Cr-OUT

VIDEO-Y/CVBS-IN

20 20

22 22VIDEO-C-IN

VIDEO-C

VIDEO-Pb/Cb

VIDEO-Pr/Cr

VIDEO-Y/CVBS

VIDEO-C

TO DIGITAL

SIGNAL

PROCESS

BLOCK

DIAGRAM

TO SYSTEM

CONTROL

BLOCK DIAGRAM

AV CBA

DVD MAIN CBA UNIT

1-9-3

E7E2ABLV

Page 21

Audio Block Diagram

REC AUDIO SIGNAL PB AUDIO SIGNAL

JK2206

Q1241

DIGITAL

AUDIO OUT

(COAXIAL)

BUFFER

IC1201

)

OP AMP

(

AMP

Q1203 Q1201

REAR

MUTE-ONDRIVE

JK2201

AUDIO(L)

-OUT1

Q1202

AMP

AUDIO(R)

MUTE-ON

-OUT1

(INPUT SELECT)

IC1022

JK2103

AUDIO(L)

-IN2

FRONT

JK2104

AUDIO(R)

-IN2

REAR

AUDIO(L)

-IN1

AUDIO(R)

-IN1

JK2106

TO SYSTEM CONTROL

BLOCK DIAGRAM

SW CTL

POFF-SELECT

11 9

Q1513

AMP

Q1512

AV CBADVD MAIN CBA UNIT

(R-CH)

IN1

IN2

AMP

9 10

SW CTL

Q1101

Q1102

AUDIO-SW2

AUDIO-SW1

IN1

(L-CH)

(AUDIO INPUT SELECT)

IC1101

)

OP AMP

(

IC1102

IN2

AMP

WF7

CN1051

CN101

33SPDIF

SPDIF

WF6

AUDIO(L)-OUT

17 17

CN701 CN1101

AUDIO-L

AUDIO(R)-OUT

DVD-AUDIO-MUTE

AUDIO(L)-IN

15 15

18 18

11 11

AUDIO-R

DVD-AUDIO-MUTE

AUDIO(R)-IN

13 13

IC802 (AUDIO A/D CONVERTER)

L-CH

789

LRCK

R-CH

BCK

DATA

AUDIO A/D

CONVERTER

101112

AIMS

SYSCLK

TO SYSTEM CONTROL

BLOCK DIAGRAM

TO DIGITAL

SIGNAL

1-9-4

PROCESS

BLOCK

DIAGRAM

E7E2ABLA

Page 22

Power Supply Block Diagram

DVD MAIN

CBA UNIT

P-ON+1.8V

6,7

CN101

EV+10.5V

25-27

CN1051

P-ON+5V

P-ON+3.3V

20-22

15-17

EV+2.8V

10-12

IC1504

REG.

+1.8V

1 2

SYSTEM

CONTROL

BLOCK

PWSW

POW-SW

REG-CONT2

REG-CONT

DIAGRAM

AL-30V

EV+10.5V

-FL

EV+3.3V

P-ON+5V

VIDEO+5V

AUDIO+10V

P-ON+3.3V

INSEL+5V

EV+5V

REG.

+3.3V

IC1503

1 2

NOTE:

The voltage for parts in hot circuit is measured using

hot GND as a common terminal.

SW+5V

Q1053

SW+10.5V

Q1054

"Ce symbole reprèsente un fusible à fusion rapide."

"This symbol means fast operating fuse."

CAUTION !

For continued protection against fire hazard,

Risk of fire-replace fuse as marked.

replace only with the same type fuse.

ATTENTION : Pour une protection continue les risqes

d'Incele n'utiliser que des fusible de même type.

A V

+3.3V

Q1063

D1063

REG.

CN1060CN1070

1-3 EV+10.5V 1-3

RECTIFIER

10-12

22-27

+5V-L

EV+2.8V

6-9 EV+5V 6-9

10-12

22-27

RECTIFIER

D1057, D1058

28 AL-30V 28

29 F2 29

30 F1 30

Q1506

RECTIFIER

D1056, D1077

171516

Q1505

SW+5V

Q1057

Q1056

AV CBA

RECTIFIER

D1054

D1051

117

Q1060

COLD

T1001

BRIDGE

RECTIFIER

D1001-D1004

LINE

FILTER

L1001

F1001

HOT CIRCUIT. BE CAREFUL.

CAUTION !

Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.

If Main Fuse (F1001) is blown , check to see that all components in the power supply

circuit are not defective before you connect the AC plug to the AC power supply.

Otherwise it may cause some components in the power supply circuit to fail.

1A 250V

AC1001

AC CORD

A V

1-9-5

Q1002

Q1001

CTL

IC1001

ERROR

VOLTAGE DET

4 1

HOT

CTL

Q1003

POWER SUPPLY CBA

E7E2ABLP

Page 23

SCHEMATIC DIAGRAMS / CBA’S AND TEST POINTS

Standard Notes

WARNING

Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts that have these special safety characteristics are identified in this manual and its supplements; electrical components having such features are identified by the mark “#” in the schematic diagram and the parts list. Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement parts that do not have the same safety characteristics as specified in the parts list may create shock, fire, or other hazards.

Notes:

1. Do not use the part number shown on these drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since these drawings were prepared.

2. All resistance values are indicated in ohms (K = 10

3. Resistor wattages are 1/4W or 1/6W unless otherwise specified.

4. All capacitance values are indicated in µF (P = 10

5. All voltages are DC voltages unless otherwise specified.

, M = 106).

-6

µF).

1-10-1 R2N_SC

Page 24

LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES:

1. CAUTION:

FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE

A V

SAME TYPE FUSE. ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQES D'INCELE N'UTILISER QUE DES FUSIBLE DE MÊME TYPE. RISK OF FIRE-REPLACE FUSE AS MARKED.

This symbol means fast operating fuse. Ce symbole represente un fusible a fusion rapide.

2. CAUTION:

Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F1001) is blown, first check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.

3. Note:

1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since the drawings were prepared.

2. To maintain original function and reliability of repaired units, use only original replacement parts which are listed with their part numbers in the parts list section of the service manual.

4. Voltage indications for PLAY and REC mode on the schematics are as shown below:

(Unit: Volt)

The same voltage for both PLAY & REC modes

5.0

5.0 (2.5)

Indicates that the voltage is not consistent here.

PLAY mode REC mode

5. How to read converged lines

1-D3 Distinction Area

Line Number (1 to 3 digits)

1-B1

AREA D3

AREA B1

Examples:

1. "1-D3" means that line number "1" goes to the line number "1" of the area "D3".

1-D3

2. "1-B1" means that line number "1" goes to the line number "1" of the area "B1".

ABCD

6. Test Point Information

: Indicates a test point with a jumper wire across a hole in the PCB. : Used to indicate a test point with a component lead on foil side. : Used to indicate a test point with no test pin. : Used to indicate a test point with a test pin.

1-10-2 R2N_SC

Page 25

AV 1/5 Schematic Diagram

* NOTE

IC1502

R3112N191A-TR-FA /R3112N191A-TR-FB /BU4219G-TR

PST3619NR

Group A Group B

C1509 0.015 0.1

These components (IC1502, C1509) can be used in any models. However, you cannot mix components under Group A with the ones under Group B. You can choose either Group. The difference between Group A and Group B is shown below.

1-10-3

E7E2ASCAV1

Page 26

AV 2/5 Schematic Diagram

1-10-4

E7E2ASCAV2

Page 27

AV 3/5 Schematic Diagram

1-10-5

E7E2ASCAV3

Page 28

AV 4/5 Schematic Diagram

1-10-6

E7E2ASCAV4

Page 29

AV 5/5 Schematic Diagram

DTV BS CS

VCR

HDD

DVD

5G 4G 3G 2G 1G

7G 6G 5G 4G 3G 2G 1G

P7 d

P8 S1

FL2001 MATRIX CHART

PM BS CS DR

VCR

HDD

DVD

DTV

1-10-7

E7E2ASCAV5

Page 30

NOTE:

The voltage for parts in hot circuit is measured using hot GND as a common terminal.

Power Supply Schematic Diagram

A V

CAUTION !

For continued protection against fire hazard, replace only with the same type fuse. ATTENTION : Pour une protection continue les risqes d'Incele n'utiliser que des fusible de même type. Risk of fire-replace fuse as marked.

"This symbol means fast operating fuse." "Ce symbole reprèsente un fusible à fusion rapide."

CAUTION !

Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F1001) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.

1-10-8

E7E2ASCP

Page 31

SW Schematic Diagram

1-10-9

E7E2ASCSW

Page 32

DVD Main 1/5 Schematic Diagram

1 NOTE:

The order of pins shown in this diagram is different from that of actual IC101. IC101 is divided into five and shown as IC101 (1/5) ~ IC101 (5/5) in this DVD Main Schematic Diagram Section.

1-10-10

E7E2ASCD1

Page 33

DVD Main 2/5 Schematic Diagram

1 NOTE:

The order of pins shown in this diagram is different from that of actual IC101. IC101 is divided into five and shown as IC101 (1/5) ~ IC101 (5/5) in this DVD Main Schematic Diagram Section.

1-10-11

E7E2ASCD2

Page 34

DVD Main 3/5 Schematic Diagram

1 NOTE:

The order of pins shown in this diagram is different from that of actual IC101. IC101 is divided into five and shown as IC101 (1/5) ~ IC101 (5/5) in this DVD Main Schematic Diagram Section.

1-10-12

E7E2ASCD3

Page 35

DVD Main 4/5 Schematic Diagram

1 NOTE:

The order of pins shown in this diagram is different from that of actual IC101. IC101 is divided into five and shown as IC101 (1/5) ~ IC101 (5/5) in this DVD Main Schematic Diagram Section.

1-10-13

E7E2ASCD4

Page 36

DVD Main 5/5 Schematic Diagram

1 NOTE:

The order of pins shown in this diagram is different from that of actual IC101. IC101 is divided into five and shown as IC101 (1/5) ~ IC101 (5/5) in this DVD Main Schematic Diagram Section.

1-10-14

E7E2ASCD5

Page 37

AV CBA Top View

1-10-15

BE7E2AF01011A

Page 38

AV CBA Bottom View

WF3

C1231 PLUS LEAD

WF4

WF6

PIN 3 OF CN1101

WF5

PIN 5 OF CN1101

WF1

PIN 7 OF CN1101

WF2

WF5

PIN 9 OF CN1101

WF6

WF4

PIN 17 OF CN1101

WF7

PIN 3 OF CN1051

1-10-16

BE7E2AF01011A

Page 39

Power Supply CBA Top View

NOTE:

The voltage for parts in hot circuit is measured using hot GND as a common terminal.

Because a hot chassis ground is present in the power supply circut, an isolation transformer must be used. Also, in order to have the ability to increase the input slowly, when troubleshooting this type power supply circuit, a variable isolation transformer is required.

CAUTION !

A V

CAUTION !

"This symbol means fast operating fuse." "Ce symbole reprèsente un fusible à fusion rapide."

1-10-17

BE7E2AF01011B

Page 40

Power Supply CBA Bottom View

NOTE:

The voltage for parts in hot circuit is measured using hot GND as a common terminal.

CAUTION !

A V

CAUTION !

"This symbol means fast operating fuse." "Ce symbole reprèsente un fusible à fusion rapide."

1-10-18

BE7E2AF01011B

Page 41

SW CBA Top View

SW CBA Bottom View

1-10-19

BE7E2AF01011C

Page 42

WF1

Pin 7 of CN1101

WAVEFORMS

WF5

Pin 5 of CN1101

VIDEO-Y 0.2V 20µsec

WF2

Pin 9 of CN1101

VIDEO-C 0.2V 20

WF3

C1231 PLUS LEAD

VIDEO-Cr

WF6

Pin 17 of CN1101

sec

AUDIO(L)-OUT

WF7

Pin 3 of CN1051

0.2V 20µsec

1V 0.5ms

VIDEO-CVBS 0.5V 20

WF4

Pin 3 of CN1101

VIDEO-Cb

0.2V 20µsec

sec

SPDIF 1V 0.1

sec

NOTE:

Input: COLOR BAR SIGNAL (WITH 1KHz AUDIO SIGNAL)

1-11-1

RL4NFWF

Page 43

WIRING DIAGRAM

FRONT

DIGITAL

VIDEO

REAR

AUDIO(R)

-IN2

AUDIO(L)

-IN2

VIDEO

-IN2

S-VIDEO

IN2

AUDIO OUT

(COAXIAL)

AUDIO

(R)-OUT1

AUDIO

(L)-OUT1

VIDEO

-OUT

-Pr/Cr

OUT

-Pb/Cb

OUT

VIDEO

-Y OUT

AUDIO

(R)-IN1

AUDIO

(L)-IN1

VIDEO

-IN1

S-VIDEO

OUT

S-VIDEO

IN1

EV+10.5V 11

CN1060 CN1070

FCS(+)

TRK(+)

TRK(-)

LDD-IIN4 LDD-IIN3 LDD-IIN2 LDD-IINR

NU LDD-VDD LDD-VDD

LDD-ENABLE

GND

LDD-WEN4

GND

LDD-WEN3

GND

LDD-WEN2

LDD-SEL1

PD-VC

PD-VSW

RF(+)

RF(-)

GND GND

FSPD-VC

FSPD-VSW

FSPD-VOUT

CN1001

AC CORD

1 2FCS(-) 3 4 5TILT(+) 6TILT(-) 7 8

9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

28 29 30

34 35 36 37 38 39 40

1 2

RELAY CBA

3 4 5 6 7

CN1002

9 10 11

FOCUS ACTUATOR

TRACKING ACTUATOR

TILT ACTUATOR

DVD-LD

CD-LD

DVD/CD LASER DIODE DRIVE

DVD MECHANISM & DVD MAIN CBA ASSEMBLY

PICKUP

PDIC

FPDIC

SLED

MOTOR

SPINDLE

MOTOR

POWER

SUPPLY

CBA

1515

EV+10.5V 33

EV+10.5V 22

GND 44

EV+5V 99

GND 55

EV+5V 66

+5V-L 1111

+5V-L 1212

+5V-L 1010

EV+5V 77

EV+5V 88

AV CBA

JW010 NU 11 NU 22 KEY-1 33 GND 44

CN1062

KEY-2 55

SW CBA

NU 66

GND 1717

GND 1313

GND 1414

GND

GND 1616

NU 1919

GND 1818

CN1061

CN1101

CN1051

NU 2020

SUB-RXD 3030 RDY 2929 SUB-TXD 2828 SYS-RESET 2727 SUB-SCLK 2626 GND 2525 GND 2424 GND 2323 VIDEO-C-IN 2222 GND 2121 VIDEO-Y/CVBS-IN AUDIO+5V 1919 DVD-AUDIO-MUTE AUDIO(L)-OUT GND AUDIO(R)-OUT GND AUDIO(R)-IN 1313 GND 1212 AUDIO(L)-IN 1111 GND VIDEO-C-OUT 99 GND 88 VIDEO-Y(I/P)-OUT GND 66 VIDEO-Pr/Cr-OUT GND VIDEO-Pb/Cb-OUT

GND 30

GND 29 GND 28

28 27

EV+10.5V 27

EV+10.5V 26

EV+10.5V 25

GND 24

GND 23

P-ON+5V 22

P-ON+5V 21

P-ON+5V 20

GND 19

GND 18 P-ON+3.3V 17

P-ON+3.3V 16

P-ON+3.3V 15

GND 14

GND 13

EV+2.8V 12

EV+2.8V 11

EV+2.8V 10

GND 9

GND 8

P-ON+1.8V 7

P-ON+1.8V 6

GND 5

GND 4

SPDIF 3

GND 2

1V2CONT 1

NU 2121

EV+2.8V 2222

JW002

JW001

EV+2.8V 2525

EV+2.8V 2727

AL-30V 2828

F2 2929

F1 3030

EV+2.8V 2626

EV+2.8V 2323

EV+2.8V 2424

2020

1818 1717 1616 1515

CN701

1414

1010

55 44 33

SW1

17 2

SL(-)

16 3

SL(+)

15 4

CN101

GND

14 5

T-SCN2

13 6

T-SCN3

12 7

VH(-)

11 8

HW(-)

10 9

910

HW(+)

CN301

HV(-)

811

HV(+)

712

HU(-)

613

HU(+)

514

VCC

415

316

217 118

LDD-OSCEN

DVD MAIN CBA UNIT

CN201

PD/FSPD-VCC

DVD MECHANISM

1-12-1

E7E2AWI

Page 44

SYSTEM CONTROL TIMING CHARTS

Tray ejection

Power on

INNER-SW

open?

Tray insertion

INNER-SW

open?

Ye s

To disc

distinction

Ye s

[ Tray Open ]

button is pressed.

Tray insertion

Push Close

[ Tray Open ]

button is pressed.

INNER-SW

open?

Ye s

SLED

moves

Tray ejection

1-13-1 R4NTI

Page 45

Parameter

Tray open

Tray ejection direction

SLED

V*: Voltage T*: Event timer

V0: 2.40 V T1: 0.050 s V1: 4.25 V T2: 2.000 s V2: 2.00 V T3: 0.008 s V3: 2.36 V T4: 0.006 s V4: 4.26 V T5: 0.066 s

T6: 1.500 s T7: 0.800 s T8: 0.005 s

Tray close

Tray insertion direction

open

INNER-SW

Tray ejection direction

SLED

Tray insertion direction

open

INNER-SW

1-13-2 R4NTI

Page 46

Push close

Threshold level

0.08 V

0.02 s

Push Close detection

1-13-3 R4NTI

Page 47

IC PIN FUNCTION DESCRIPTIONS

IC1501 (SUB MICRO CONTROLLER)

IN/

No.

OUT

1 IN KEY-1 Key Data Input 1 2 IN KEY-2 Key Data Input 2 3 IN POW-SW Abnormal Voltage Detection 4 IN AFT Tuner Voltage Input Signal

56 IN VCC +3.3V Power Supply

7 IN VCC +3.3V Power Supply 8 OUT XOUT Main Clock Output

9 IN XIN Main Clock Input 10 - GND Ground 11 IN XCIN Sub Clock Input 12 OUT XCOUT Sub Clock Output 13 - GND Ground

14 IN RESET 15 - NU Not Used

16 - NU Not Used 17 - NU Not Used

18 OUT SUB-TXD

19 IN SUB-RXD

20 OUT SUB-SCLK 21 - NU Not Used 22 OUT 23 - NU Not Used

24 - NU Not Used 25 - NU Not Used

26 OUT 27 IN REMOTE Remote Signal Input

28 - NU Not Used

29 IN RDY

30 IN P-DOWN 31 OUT FL-SEL FL Select (Low Level)

32 - NU Not Used

Signal

Name

FLASHVPP

SYSRESET

REGCONT2

Function

Flash Writing Voltage

Micro Controller Reset Signal

Transmission Data to Main Micro Controller

Reception Data from Main Micro Controller

Communication Clock with Main Micro Controller

System Reset Signal

Power Regulator Control Signal

Ready/Busy communication Control with Main Micro Controller

Power Voltage Down Detector Signal

IN/

No.

OUT

33 - NU Not Used 34 - NU Not Used

IN/

OUT

36 OUT

37 OUT 38 - NU Not Used 39 OUT

40 OUT

41 OUT

42 OUT

43 OUT

44 OUT 45 - NU Not Used

46 - NU Not Used 47 - NU Not Used 48 OUT FL-DIN FL Serial Data 49 OUT FL-STB FL Serial Interface Strobe 50 OUT FL-SCL FL Serial Clock 51 - NU Not Used

52 OUT 53 OUT PWSW Power On Signal Output

54 - NU Not Used 55 - NU Not Used 56 - NU Not Used 57 - NU Not Used 58 - NU Not Used 59 - NU Not Used 60 - NU Not Used 61 - GND Ground 62 - NU Not Used 63 - NU Not Used 64 - NU Not Used

Signal

Name

FLASHSDA

FLASHSCL

POFFSELECT

AUDIOSW2

AUDIOSW1

VIDEOSW1

VIDEOSW2

VIDEOSW3

VIDEOMUTE

REGCONT

Function

Serial Data Signal for Flash

Serial Clock Signal for Flash

Power Off Select Signal

Audio Input Select Signal

Video Input Select Signal

Video Mute Control Signal

Power Regulator Control Signal

1-14-1 E7E2APIN

Page 48

IC2001 (VFD DRIVER)

IN/

No.

OUT

1 IN CLK Serial Clock

2 IN STB Serial Interface Strobe

3 - NU Not Used

4 - NU Not Used

5 - VSS GND

6 - VDD Power Supply

8 b

9 c 10 d

OUT

11 e 12 f 13 g 14 h 15 - VEE Pull Down Level 16 OUT i Segment Output 17 18 6G 19 5G

OUT

20 4G 21 3G 22 2G 23 1G 24 - VDD Power Supply 25 - VSS GND 26 IN OSC Oscillator Input 27 - NU Not Used 28 IN DIN Serial Data Input

Signal

Name

Function

Segment Output

Grid Output

1-14-2 E7E2APIN

Page 49

LEAD IDENTIFICATIONS

ECB

KRC103M-AT/P KTA1267-GR-AT/P KTC3199-GR-AT/P

PQ070XF01SZHMM1697AJBE

ECB

1234

KTA-1266-GR-AT/P KTA1271-Y-AT/P KTC3203-Y-AT/P

2SK3757(Q)

KRC102S-RTK/P

GDS

KIA4558P/P

KTB1151-Y-U/P

E C B

MN101C77AFP1

PS2561A-1(W)

1: Anode

2: Cathode

3: Emitter 4: Collector

CD4052BNSR CD4053BNSR MM1637XVBE

UTC4580E

BU4219G-TR

PT6313-S-TP(L)

R3112N191A-TR-FA R3112N191A-TR-FB PST3619NR

123

Note:

MM1509XNRE

A: Anode K: Cathode E: Emitter C: Collector B: Base R: Reference

123

G: Gate D: Drain S: Source

1-15-1 E7E2ALE

Page 50

Cabinet

EXPLODED VIEWS

See Electrical Parts List for parts with this mark.

Some Ref. Numbers are not in sequence.

2L030

2B49

2L050

2L010

2L041

AC1001

POWER SUPPLY CBA

2L010

2B10

2L040

2B6

DVD Mechanism & DVD Main CBA Assembly

A11

A1X

A23

2B22

2L044

2B15

2B11

AV CBA

2L011

2L020

2L042

SW CBA

1-16-1 E7E2ACEX

Page 51

Packing

Unit

Upper Side Lower Side

X20

X22

X5 X2

Some Ref. Numbers are not in sequence.

1-16-2 E7E2APEX

Page 52

MECHANICAL PARTS LIST

PRODUCT SAFETY NOTE: Products marked with a

# have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.

NOTE: Parts that are not assigned part numbers (---------) are not available.

Ref. No. Description Part No.

A1X FRONT ASSEMBLY E7E2AUD 1VM222851 A2 CHASSIS E7C40UD 1VM121059G A3 TOP COVER E7C40UD 1VM121060 A4 REAR PANEL E7E2AUD 1VM222894 A5 FOOT H5100UD 0VM406940A A6 MODEL NO LABEL E7E2AUD ---------A8 LABEL BAR CODE HB400UD ---------A11 LABEL TELEPHONE NUMBER

A23 PCB CUSHION E7C40UD 1VM425421A 2B10 PCB SUPPORT/PCB SPACERS KGLS-14S XP0U027WD001 2B11 FRONT BRACKET R E2A00JD 1VM424123F 2B15 MAIN PCB HOLDER E2B10ED 1VM323176A 2B22 HIMELON TAPE(30*5) E7C40UD 1VM425436 2B49 M-PCB PLATE EARTH E6700UD 1VM421132 2L010 SCREW C-TIGHT M3X5 BIND HEAD + GBCC3050 2L011 SCREW C-TIGHT M3X5 BIND HEAD + GBCC3050 2L020 SCREW B-TIGHT M3X8 BIND HEAD+ GBHB3080 2L030 SCREW P-TIGHT 3X10 BIND HEAD+ GBJP3100 2L040 SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060 2L041 SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060 2L042 SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060 2L044 SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060 2L050 SCREW S-TIGHT M3X10 BIND HEAD+ GBJS3100

H5730UD(SYLVANIA)

PACKING

S1 GIFTBOX CARTON E7E2AUD 1VM323776 S2 SIDE PAD E7C40UD 1VM121069 S3 UNIT BAG E5500UD 0VM411683

ACCESSORIES

X1 REMOTE CONTROL UNIT NB089UD NB089UD X2 DRY BATTERY R6P/2S XB0M451T0001 X4 ACCESSORY BAG E5795ED 0VM416059 X5 AV CORD 1000/BLACK WPZ0102TM018 X20# OWNERS MANUAL E7E2AUD 1VMN23368 X22 QUICK GUIDE E7E2AUD 1VMN23370

----------

20070307 1-17-1 E7E2ACA

Page 53

ELECTRICAL PARTS LIST

PRODUCT SAFETY NOTE: Products marked with a

NOTES:

1. Parts that are not assigned part numbers (---------) are not available.

2. Tolerance of Capacitors and Resistors are noted with the following symbols.

C.....±0.25% D.....±0.5% F.....±1%

G.....±2% J......±5% K.....±10%

M.....±20% N.....±30% Z.....+80/-20%

DVD MECHANISM & DVD MAIN CBA ASSEMBLY

Ref. No. Description Part No.

DVD MECHANISM & DVD MAIN CBA ASSEMBLY

N78F2DUN

AV ASSEMBLY

Ref. No. Description Part No.

AV ASSEMBLY Consists of the following:

AV CBA (SUB-A) POWER SUPPLY CBA (SUB-B) SW CBA (SUB-C)

AV CBA

Ref. No. Description Part No.

AV CBA (SUB-A) Consists of the following:

CAPACITORS

C1053 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 C1069 CHIP CERAMIC CAP.(1608) B K 1µF/10V CHD1AK30B105 C1070 ELECTROLYTIC CAP. 100µF/6.3V M CE0KMASDL101 C1075 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1076 ELECTROLYTIC CAP. 100µF/6.3V M CE0KMASDL101 C1081 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1082 ELECTROLYTIC CAP. 100µF/6.3V M CE0KMASDL101 C1101 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1102 ELECTROLYTIC CAP. 100µF/6.3V M CE0KMASDL101 C1121 ELECTROLYTIC CAP. 10µF/16V M CE1CMASDL100 C1122 ELECTROLYTIC CAP. 10µF/16V M CE1CMASDL100 C1123 CHIP CERAMIC CAP.(1608) CH J 33pF/50V CHD1JJ3CH330 C1124 CHIP CERAMIC CAP.(1608) CH J 33pF/50V CHD1JJ3CH330 C1125 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1135 ELECTROLYTIC CAP. 220µF/16V M CE1CMASDL221 C1152 ELECTROLYTIC CAP. 100µF/16V M CE1CMASDL101 C1171 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102 C1172 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102 C1175 ELECTROLYTIC CAP. 10µF/16V M CE1CMASDL100 C1176 ELECTROLYTIC CAP. 10µF/16V M CE1CMASDL100 C1181 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102

1VSA15675

----------

Ref. No. Description Part No.

C1182 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102 C1185 ELECTROLYTIC CAP. 10µF/16V M CE1CMASDL100 C1186 ELECTROLYTIC CAP. 10µF/16V M CE1CMASDL100 C1201 ELECTROLYTIC CAP. 10µF/16V M CE1CMASDL100 C1202 ELECTROLYTIC CAP. 10µF/16V M CE1CMASDL100 C1203 CHIP CERAMIC CAP.(1608) CH J 470pF/50V CHD1JJ3CH471 C1204 CHIP CERAMIC CAP.(1608) CH J 470pF/50V CHD1JJ3CH471 C1205 CHIP CERAMIC CAP.(1608) CH J 68pF/50V CHD1JJ3CH680 C1206 CHIP CERAMIC CAP.(1608) CH J 68pF/50V CHD1JJ3CH680 C1211 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1212 ELECTROLYTIC CAP. 470µF/6.3V M CE0KMASDL471 C1221 ELECTROLYTIC CAP. 10µF/16V M CE1CMASDL100 C1222 ELECTROLYTIC CAP. 10µF/16V M CE1CMASDL100 C1231 ELECTROLYTIC CAP. 470µF/6.3V M CE0KMASDL471 C1232 ELECTROLYTIC CAP. 100µF/16V M CE1CMASDL101 C1241 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1247 CHIP CERAMIC CAP.(1608) B K 1µF/10V CHD1AK30B105 C1301 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1302 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1303 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1304 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1305 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1306 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1313 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 C1314 ELECTROLYTIC CAP. 22µF/16V M CE1CMASDL220 C1315 ELECTROLYTIC CAP. 100µF/6.3V M CE0KMASDL101 C1316 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1331 CHIP CERAMIC CAP.(1608) CH J 33pF/50V CHD1JJ3CH330 C1332 CHIP CERAMIC CAP.(1608) CH J 33pF/50V CHD1JJ3CH330 C1333 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1334 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1335 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1336 PCB JUMPER D0.6-P5.0 JW5.0T C1337 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1338 ELECTROLYTIC CAP. 100µF/6.3V M NP CP0KMASNC101 C1405 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 C1406 ELECTROLYTIC CAP. 1µF/50V M CE1JMASDL1R0 C1407 ELECTROLYTIC CAP. 1µF/50V M CE1JMASDL1R0 C1408 ELECTROLYTIC CAP. 1µF/50V M CE1JMASDL1R0 C1409 ELECTROLYTIC CAP. 22µF/16V M CE1CMASDL220 C1410 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 C1411 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1413 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1414 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1415 ELECTROLYTIC CAP. 100µF/6.3V M CE0KMASDL101 C1417 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1418 PCB JUMPER D0.6-P5.0 JW5.0T C1419 ELECTROLYTIC CAP. 1000µF/6.3V M CE0KMASDL102 C1420 ELECTROLYTIC CAP. 470µF/6.3V M CE0KMASDL471 C1421 ELECTROLYTIC CAP. 470µF/6.3V M CE0KMASDL471 C1501 ELECTROLYTIC CAP. 1000µF/6.3V M CE0KMASDL102 C1502 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1503 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1506 CHIP CERAMIC CAP.(1608) CH J 22pF/50V CHD1JJ3CH220 C1507 CHIP CERAMIC CAP. CH J 18pF/50V CHD1JJ3CH180 C1508 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104

If C1509 is 0.015µF, then IC1502 is R3112N191A-TR-FA, R3112N191A-TR-FB or BU4219G-TR.

C1509 CHIP CERAMIC CAP.(1608) B K 0.015µF/50V CHD1JK30B153 IC1502 VOLTAGE DETECT R3112N191A-TR-FA QSZBA0TRC021

20070307 1-18-1 E7E2AEL

Page 54

Ref. No. Description Part No.

IC1502 VOLTAGE DETECT R3112N191A-TR-FB QSZBA0TRC022 IC1502 RESET IC BU4219G-TR QSZBA0TRM090

If C1509 is 0.1µF, then IC1502 is PST3619NR.

C1509 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104 IC1502 SYSTEM RESET PST3619NR QSZBA0TMM151 C1511 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1512 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101 C1513 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101 C1520 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1575 ELECTROLYTIC CAP. 100µF/6.3V M(105C) CE0KMASTH101 C1576 ELECTROLYTIC CAP. 100µF/6.3V M(105C) CE0KMASTH101 C1577 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1578 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1601 ELECTROLYTIC CAP. 4.7µF/25V M CE1EMASDL4R7 C1602 ELECTROLYTIC CAP. 4.7µF/25V M CE1EMASDL4R7 C1801 ELECTROLYTIC CAP. 22µF/6.3V M CE0KMASDL220 C1802 ELECTROLYTIC CAP. 100µF/6.3V M CE0KMASDL101 C1803 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1804 ELECTROLYTIC CAP. 10µF/16V M CE1CMASDL100 C1806 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 C1809 ELECTROLYTIC CAP. 100µF/6.3V M CE0KMASDL101 C1810 ELECTROLYTIC CAP. 4.7µF/25V M CE1EMASDL4R7 C1811 ELECTROLYTIC CAP. 4.7µF/25V M CE1EMASDL4R7 C2001 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C2002 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101 C2003 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C2004 ELECTROLYTIC CAP. 100µF/6.3V M CE0KMASDL101 C2005 ELECTROLYTIC CAP. 100µF/6.3V M CE0KMASDL101 C2006 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C2007 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C2008 ELECTROLYTIC CAP. 3.3µF/50V M CE1JMASDL3R3 C2009 ELECTROLYTIC CAP. 3.3µF/50V M CE1JMASDL3R3 C2010 ELECTROLYTIC CAP. 3.3µF/50V M CE1JMASDL3R3

CONNECTORS

CN1051 30PIN FFC WX1E7H50-003 WX1E7H50-003 CN1060 FFC CONNECTOR 30PIN IMSA-9615S-30A-

CN1061 FFC CONNECTOR IMSA-9615S-06A-PP-A JC96J06ER007 CN1101 28PIN FFC WX1E7H50-002 WX1E7H50-002

PP-A

JC96J30ER007

DIODES

D1053 ZENER DIODE MTZJT-7720B QDTB00MTZJ20 D1060 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1061 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1062 ZENER DIODE MTZJT-774.3A QDTA0MTZJ4R3 D1065 PCB JUMPER D0.6-P10.0 JW10.0T D1070 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1161 ZENER DIODE MTZJT-775.1C QDTC0MTZJ5R1 D1301 ZENER DIODE MTZJT-776.2B QDTB0MTZJ6R2 D1302 ZENER DIODE MTZJT-776.2B QDTB0MTZJ6R2 D1303 ZENER DIODE MTZJT-776.2B QDTB0MTZJ6R2 D1304 ZENER DIODE MTZJT-776.2B QDTB0MTZJ6R2 D1311 ZENER DIODE MTZJT-776.2B QDTB0MTZJ6R2 D1312 ZENER DIODE MTZJT-776.2B QDTB0MTZJ6R2 D1313 ZENER DIODE MTZJT-776.2B QDTB0MTZJ6R2 D1314 ZENER DIODE MTZJT-776.2B QDTB0MTZJ6R2 D1507 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1508 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1509 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1510 PCB JUMPER D0.6-P5.0 JW5.0T

ICS

IC1021 IC 75 Ω DRIVER MM1509XNRE QSZBA0TMM169 IC1022 IC ANALOG MULTIPLEXER CD4053BNSR NSZBA0TTY093 IC1101 IC SWITCHING CD4052BNSR NSZBA0TTY091

Ref. No. Description Part No.

IC1102 IC OP AMP UTC4580E NSZBA0T2H010 IC1201 IC OP AMP KIA4558P/P NSZBA0SJY035 IC1301 VIDEO SWITCH MM1697AJBE QSZBA0TMM150 IC1401 DRIVER FOR DVD MM1637XVBE QSZBA0TMM102 IC1501 IC MICROCONTROLLER MN101C77AFP1 QSZAB0RMS080

If IC1502 is R3112N191A-TR-FA, R3112N191A-TR-FB or BU4219G-TR, then C1509 is 0.015µF.

IC1502 VOLTAGE DETECT R3112N191A-TR-FA QSZBA0TRC021 IC1502 VOLTAGE DETECT R3112N191A-TR-FB QSZBA0TRC022 IC1502 RESET IC BU4219G-TR QSZBA0TRM090 C1509 CHIP CERAMIC CAP.(1608) B K 0.015µF/50V CHD1JK30B153

If IC1502 is PST3619NR, then C1509 is 0.1µF.

IC1502 SYSTEM RESET PST3619NR QSZBA0TMM151 C1509 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104 IC1503 VOLTAGE REGULATOR PQ070XF01SZH QSZBA0SSH054 IC1504 VOLTAGE REGULATOR PQ070XF01SZH QSZBA0SSH054 IC2001 VFD DRIVER/CONTROLLER IC PT6313-S-

TP(L)

NSZBA0TG2007

COILS

L1054 CHOKE COIL 22µH-K LLBD00PKV021 L1055 CHOKE COIL 22µH-K LLBD00PKV021 L1056 CHOKE COIL 22µH-K LLBD00PKV021 L1241 INDUCTOR(100µH K) LAP02TA101K LLAXKATTU101 L1242 INDUCTOR(0.47µH K) LAP02TAR47K LLAXKATTUR47 L1401 PCB JUMPER D0.6-P5.0 JW5.0T L2001 INDUCTOR(100µH K) LAP02TA101K LLAXKATTU101

TRANSISTORS

Q1053 TRANSISTOR KTB1151-Y-U/P NQEY0KTB1151 Q1054 TRANSISTOR (PB FREE) KTA1271-Y-AT/P NQSYKTA1271P Q1056 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P Q1057 TRANSISTOR KTC3203-Y-AT/P NQSYKTC3203P Q1063 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P Q1101 TRANSISTOR KRC102S-RTK/P NQ1ZKRC102SP Q1102 TRANSISTOR KRC102S-RTK/P NQ1ZKRC102SP Q1201 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P Q1202 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P Q1203 TRANSISTOR KTA1266-Y-AT/P NQSYKTA1266P Q1241 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P Q1303 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P Q1304 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P Q1501 TRANSISTOR KTA1266-Y-AT/P NQSYKTA1266P Q1502 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P Q1505 NPN TRANSISTOR KRC103M-AT/P NQSZKRC103MP Q1506 NPN TRANSISTOR KRC103M-AT/P NQSZKRC103MP Q1511 NPN TRANSISTOR KRC103M-AT/P NQSZKRC103MP Q1512 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P Q1513 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P Q1601 TRANSISTOR KTA1266-Y-AT/P NQSYKTA1266P

RESISTORS

R1051 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000 R1054 CARBON RES. 1/4W G 9.1 Ω RCX4GATZ09R1 R1055 CARBON RES. 1/4W G 10 Ω RCX4GATZ0100 R1058 CARBON RES. 1/4W J 1.5k Ω RCX4JATZ0152 R1059 CARBON RES. 1/4W J 1.5k Ω RCX4JATZ0152 R1060 CHIP RES. 1/10W J 390 Ω RRXAJR5Z0391 R1061 CHIP RES. 1/10W J 470 Ω RRXAJR5Z0471 R1066 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473 R1067 CARBON RES. 1/4W J 180 Ω RCX4JATZ0181 R1068 CARBON RES. 1/4W J 180 Ω RCX4JATZ0181 R1070 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473 R1072 CARBON RES. 1/4W J 680 Ω RCX4JATZ0681 R1073 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473 R1074 CHIP RES. 1/10W J 620 Ω RRXAJR5Z0621

20070307 1-18-2 E7E2AEL

Page 55

Ref. No. Description Part No.

R1076 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472 R1077 CHIP RES. 1/10W J 1.1k Ω RRXAJR5Z0112 R1090 CHIP RES. 1/10W J 1.8k Ω RRXAJR5Z0182 R1095 CARBON RES. 1/4W J 150 Ω RCX4JATZ0151 R1101 CHIP RES.(1608) 1/10W F 68k Ω RRXAFR5H0683 R1102 CHIP RES.(1608) 1/10W F 68k Ω RRXAFR5H0683 R1103 CHIP RES.(1608) 1/10W F 68k Ω RRXAFR5H0683 R1104 CHIP RES.(1608) 1/10W F 68k Ω RRXAFR5H0683 R1107 CHIP RES. 1/10W J 18k Ω RRXAJR5Z0183 R1108 CHIP RES. 1/10W J 18k Ω RRXAJR5Z0183 R1109 CHIP RES. 1/10W J 18k Ω RRXAJR5Z0183 R1110 CHIP RES. 1/10W J 18k Ω RRXAJR5Z0183 R1113 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103 R1114 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103 R1117 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103 R1120 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223 R1121 CHIP RES.(1608) 1/10W F 33k Ω RRXAFR5H0333 R1122 CHIP RES.(1608) 1/10W F 33k Ω RRXAFR5H0333 R1139 CHIP RES. 1/10W J 300 Ω RRXAJR5Z0301 R1140 CHIP RES. 1/10W J 750 Ω RRXAJR5Z0751 R1153 CHIP RES. 1/10W J 62 Ω RRXAJR5Z0620 R1154 CHIP RES. 1/10W J 62 Ω RRXAJR5Z0620 R1173 CHIP RES. 1/10W J 180k Ω RRXAJR5Z0184 R1174 CHIP RES. 1/10W J 180k Ω RRXAJR5Z0184 R1183 CHIP RES. 1/10W J 180k Ω RRXAJR5Z0184 R1184 CHIP RES. 1/10W J 180k Ω RRXAJR5Z0184 R1201 CHIP RES.(1608) 1/10W F 3.6k Ω RRXAFR5H0362 R1202 CHIP RES.(1608) 1/10W F 3.6k Ω RRXAFR5H0362 R1203 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332 R1204 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332 R1205 CHIP RES.(1608) 1/10W F 11k Ω RRXAFR5H0113 R1206 CHIP RES.(1608) 1/10W F 11k Ω RRXAFR5H0113 R1213 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102 R1221 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104 R1222 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104 R1223 CHIP RES. 1/10W J 470 Ω RRXAJR5Z0471 R1224 CHIP RES. 1/10W J 470 Ω RRXAJR5Z0471 R1225 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102 R1226 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102 R1232 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104 R1233 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000 R1242 CHIP RES. 1/10W J 1.8k Ω RRXAJR5Z0182 R1243 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222 R1244 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222 R1245 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750 R1246 CHIP RES. 1/10W J 220 Ω RRXAJR5Z0221 R1248 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104 R1301 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750 R1302 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750 R1304 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750 R1311 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750 R1312 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750 R1313 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750 R1331 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102 R1333 CHIP RES. 1/10W J 470 Ω RRXAJR5Z0471 R1334 CHIP RES. 1/10W J 470 Ω RRXAJR5Z0471 R1335 CHIP RES. 1/10W J 3k Ω RRXAJR5Z0302 R1336 CHIP RES. 1/10W J 12k Ω RRXAJR5Z0123 R1337 CHIP RES. 1/10W J 3k Ω RRXAJR5Z0302 R1338 CHIP RES. 1/10W J 12k Ω RRXAJR5Z0123 R1403 CHIP RES. 1/10W J 3k Ω RRXAJR5Z0302 R1405 CHIP RES. 1/10W J 3.9k Ω RRXAJR5Z0392 R1406 CHIP RES.(1608) 1/10W F 220 Ω RRXAFR5H0221

Ref. No. Description Part No.

R1407 CHIP RES.(1608) 1/10W F 220 Ω RRXAFR5H0221 R1408 CHIP RES.(1608) 1/10W F 220 Ω RRXAFR5H0221 R1409 CHIP RES.(1608) 1/10W F 220 Ω RRXAFR5H0221 R1420 CARBON RES. 1/4W J 75 Ω RCX4JATZ0750 R1421 CARBON RES. 1/4W J 75 Ω RCX4JATZ0750 R1422 CARBON RES. 1/4W J 75 Ω RCX4JATZ0750 R1423 CARBON RES. 1/4W J 75 Ω RCX4JATZ0750 R1424 CARBON RES. 1/4W J 75 Ω RCX4JATZ0750 R1430 CARBON RES. 1/4W J 75 Ω RCX4JATZ0750 R1501 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332 R1502 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332 R1503 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473 R1505 CHIP RES. 1/10W J 820k Ω RRXAJR5Z0824 R1506 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473 R1507 CHIP RES. 1/10W J 470 Ω RRXAJR5Z0471 R1508 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000 R1513 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101 R1514 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473 R1515 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101 R1516 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473 R1518 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473 R1519 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101 R1520 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473 R1524 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101 R1527 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101 R1528 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473 R1531 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101 R1532 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473 R1533 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103 R1534 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223 R1535 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473 R1536 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472 R1537 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472 R1538 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472 R1539 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102 R1546 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472 R1547 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472 R1554 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473 R1555 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101 R1556 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101 R1557 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101 R1564 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473 R1565 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473 R1571 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222 R1572 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102 R1573 CHIP RES.(1608) 1/10W F 1.5k Ω RRXAFR5H0152 R1574 CHIP RES.(1608) 1/10W F 680 Ω RRXAFR5H0681 R1575 CHIP RES. 1/10W F 15k Ω RRXAFR5H0153 R1576 CHIP RES.(1608) 1/10W F 3.9k Ω RRXAFR5H0392 R1577 CHIP RES.(1608) 1/10W F 10k Ω RRXAFR5H0103 R1578 CHIP RES.(1608) 1/10W F 10k Ω RRXAFR5H0103 R1579 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473 R1580 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473 R1585 CARBON RES. 1/4W J 2.7k Ω RCX4JATZ0272 R1586 CHIP RES. 1/10W J 1.5k Ω RRXAJR5Z0152 R1601 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101 R1602 CARBON RES. 1/4W J 680 Ω RCX4JATZ0681 R1604 CARBON RES. 1/4W J 680 Ω RCX4JATZ0681 R1605 CARBON RES. 1/4W J 220 Ω RCX4JATZ0221 R1606 CARBON RES. 1/4W J 220 Ω RCX4JATZ0221 R1607 PCB JUMPER D0.6-P5.0 JW5.0T R1621 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103 R1622 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103

20070307 1-18-3 E7E2AEL

Page 56

Ref. No. Description Part No.

R1623 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472 R1625 CARBON RES. 1/4W J 6.8k Ω RCX4JATZ0682 R1626 CHIP RES. 1/10W J 82k Ω RRXAJR5Z0823 R1627 CHIP RES. 1/10W J 82k Ω RRXAJR5Z0823 R1628 CHIP RES. 1/10W J 120k Ω RRXAJR5Z0124 R1629 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473 R1630 CHIP RES. 1/10W J 120k Ω RRXAJR5Z0124 R1631 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473 R2001 CHIP RES. 1/10W J 33 Ω RRXAJR5Z0330 R2003 CHIP RES. 1/10W J 68k Ω RRXAJR5Z0683 R2004 CHIP RES. 1/10W J 6.8k Ω RRXAJR5Z0682 R2008 CHIP RES. 1/10W J 10 Ω RRXAJR5Z0100 R2010 CHIP RES. 1/10W J 27 Ω RRXAJR5Z0270

SWITCH

SW3011 TACT SWITCH SKQSAF001A SST0101AL041

MISCELLANEOUS

2B6 FL HOLDER E6700UD 1VM320515A FL2001 FL 7-BT-310NA TVFD1C0FT057 JK2101 DIN SOCKET DIN-405A JXEL040YUQ03 JK2102 RCA JACK(YELLOW) MTJ-032-05B-20(B110) JXRL010LY135 JK2103 RCA JACK(WHITE) MTJ-032-05B-22(B110) JXRL010LY136 JK2104 RCA JACK(RED) MTJ-032-05A-21(B110) JYRL010LY029 JK2105 S TYPE JACK MDC-050V-2.4 LF(B110 JXEL040LY003 JK2106 RCA JACK 3PIN MSD-243V-07 NI FE LF JXRL030LY124 JK2201 RCA JACK 3PIN MSD-243V-07 NI FE LF JXRL030LY124 JK2202 S TYPE JACK MDC-050V-2.4 LF(B110 JXEL040LY003 JK2203 RCA JACK 3PIN MSD-243V-18 NI FE LF JXRL030LY132 JK2206 RCA JACK(BLACK) MSP-251V-01 NI FE LF JXRL010LY125 JP1053 PCB JUMPER D0.6-P5.0 JW5.0T JP1402 PCB JUMPER D0.6-P5.0 JW5.0T JP1404 PCB JUMPER D0.6-P9.0 JW9.0T JP1405 PCB JUMPER D0.6-P5.0 JW5.0T JP1501 PCB JUMPER D0.6-P5.0 JW5.0T JP1502 PCB JUMPER D0.6-P5.0 JW5.0T JP2104 PCB JUMPER D0.6-P5.0 JW5.0T RE2001 SENSOR REMOTE RECEIVER KSM-602LU2S USESJRSKK048 X1501 CERAMIC RESONATOR ZTT8.00MT47 FY0805PLN004 X1502 XTAL DT38 32.768kHz FX0323LDS001

POWER SUPPLY CBA

Ref. No. Description Part No.

POWER SUPPLY CBA (SUB-B) Consists of the following:

CAPACITORS

C1001# ACROSS THE LINE CAP. 0.068µF/250V CT2E683DC016 C1002# SAFETY CAP. 3300pF/250V CCD2EMA0E332 C1003 ELECTROLYTIC CAPACITOR

C1004 CERAMIC CAP. B K 0.01µF/500V CCD2JKP0B103 C1005 CERAMIC CAP. B K 220pF/500V CCD2JKS0B221 C1006 CERAMIC CAP.(AX) X K 5600pF/16V CCA1CKT0X562 C1008 CERAMIC CAP.(AX) B K 3300pF/50V CA1J332TU011 C1009 ELECTROLYTIC CAP. 10µF/16V M CE1CMASDL100 C1010 POLYESTER FILM CAP. (PB FREE) 0.022µF/

C1011 CERAMIC CAP. B K 220pF/500V CCD2JKS0B221 C1051 ELECTROLYTIC CAP. 1000µF/6.3V M CE0KMASDL102 C1052 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 C1055 ELECTROLYTIC CAP. 22µF/50V M CE1JMASDL220 C1056 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C1058 ELECTROLYTIC CAP. 3300µF/6.3V M(105C) CE0KMZATH332 C1059 CERAMIC CAP. CH J 47pF/50V CCD1JJSCH470 C1060 ELECTROLYTIC CAP. 4700µF/6.3V M(105C) CE0KMZATH472

ZR200TA151K16DB

100V J

----------

CA2D151DYG03

CA2A223DT018

Ref. No. Description Part No.

C1061 ELECTROLYTIC CAP. 2200µF/6.3V M(105C) CE0KMASTH222 C1063 ELECTROLYTIC CAP. 1000µF/16V M(105C) CE1CMASTH102 C1064 ELECTROLYTIC CAP. 470µF/16V M CE1CMASDL471 C1065 CHIP CERAMIC CAP.(1608) B K 0.033µF/50V CHD1JK30B333 C1077 CHIP CERAMIC CAP.(1608) B K 0.033µF/50V CHD1JK30B333 C1078 CHIP CERAMIC CAP.(1608) B K 0.033µF/50V CHD1JK30B333 C1080 CHIP CERAMIC CAP.(1608) B K 1µF/10V CHD1AK30B105

CONNECTOR

CN1070 30PIN FFC WX1E7H50-007 WX1E7H50-007

DIODES

D1001 DIODE 1N5397-B NDLZ001N5397 D1002 DIODE 1N5397-B NDLZ001N5397 D1003 DIODE 1N5397-B NDLZ001N5397 D1004 DIODE 1N5397-B NDLZ001N5397 D1005 PCB JUMPER D0.6-P5.0 JW5.0T D1006 RECTIFIER DIODE BA157 NDQZ000BA157 D1007 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1008 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1009 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1010 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1011 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1012 ZENER DIODE MTZJT-7718B QDTB00MTZJ18 D1013 RECTIFIER DIODE BA157 NDQZ000BA157 D1051 SCHOTTKY BARRIER DIODE SB140 NDQZ000SB140 D1054 RECTIFIER DIODE BA157 NDQZ000BA157 D1056 SCHOTTKY BARRIER DIODE SB240-B/P NDQZ000SB240 D1058 SCHOTTKY BARRIER DIODE SB340 NDQZ000SB340 D1059 ZENER DIODE MTZJT-776.8B QDTB0MTZJ6R8 D1063 RECTIFIER DIODE FR302 NDWZ000FR302 D1064 ZENER DIODE MTZJT-7713B QDTB00MTZJ13 D1067 ZENER DIODE MTZJT-776.8B QDTB0MTZJ6R8

IC1001# PHOTOCOUPLER PS2561A-1(W) QPEWPS2561A1

COILS

L1001# LINE FILTER 27MH TLF14CB2730R4 LLBG00ZTU034 L1006 BEAD CORE B16 RH 3.5X10X1.3 XL03010XM001 L1007 BEAD CORE B16 RH 3.5X10X1.3 XL03010XM001 L1051 COIL SEALED POWER INDUCTORS

L1052 POWER INDUCTORS CWKBNP-180K LLF1800KV002

CWKBNP-470K

LLF4700KV002

TRANSISTORS

Q1001 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P Q1002# FET 2SK3757(Q) QFWZ02SK3757 Q1003 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P Q1060 TRANSISTOR KTA1267-Y-AT/P NQSYKTA1267P

RESISTORS

R1002 CARBON RES. 1/4W J 680k Ω RCX4JATZ0684 R1003 CARBON RES. 1/4W J 1.8M Ω RCX4JATZ0185 R1004 CARBON RES. 1/4W J 1.8M Ω RCX4JATZ0185 R1005 CARBON RES. 1/4W J 470 Ω RCX4JATZ0471 R1006 CARBON RES. 1/4W J 820k Ω RCX4JATZ0824 R1007 METAL OXIDE FILM RES. 2W J 2.2 Ω RN02JZLZ02R2 R1008 METAL OXIDE FILM RES.(STRAIGHT 1W J 15k ΩRN01JZLZ0153

R1009 CARBON RES. 1/4W J 6.8k Ω RCX4JATZ0682 R1010 METAL OXIDE FILM RES. 2W J 0.75 Ω RN02R75ZU001 R1011 CARBON RES. 1/4W J 100k Ω RCX4JATZ0104 R1012 CARBON RES. 1/4W J 1k Ω RCX4JATZ0102 R1013 CARBON RES. 1/4W J 10k Ω RCX4JATZ0103 R1014 CARBON RES. 1/4W J 100k Ω RCX4JATZ0104 R1015 CARBON RES. 1/4W J 470k Ω RCX4JATZ0474 R1016 CARBON RES. 1/4W J 120 Ω RCX4JATZ0121 R1057 PCB JUMPER D0.6-P5.0 JW5.0T

20070307 1-18-4 E7E2AEL

Page 57

Ref. No. Description Part No.

R1063 CHIP RES. 1/10W J 10 Ω RRXAJR5Z0100 R1071 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000 R1084 CHIP RES. 1/10W J 15k Ω RRXAJR5Z0153 R1085 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102 R1089 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472 R1092 CHIP RES. 1/10W F 5.6k Ω RRXAFR5H0562 R1093 CHIP RES.(1608) 1/10W F 2.7k Ω RRXAFR5H0272 R2012 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000 R2013 CHIP RES. 1/10W J 1.8k Ω RRXAJR5Z0182

MISCELLANEOUS

AC1001# AC CORD W/O A GND WIRE UL/CSA/1660/NO/

F1001# FUSE CURRENT PEG20C0NG001 PEG20C0NG001 FH1001 FUSE HOLDER MSF-015 LF (B110) XH01Z00LY002 FH1002 FUSE HOLDER MSF-015 LF (B110) XH01Z00LY002 JP1002 PCB JUMPER D0.6-P5.0 JW5.0T T1001# SWITCHING TRANS 6755-S05 LTT2PC0KT014

BLACK

WAC0162LW010

SW CBA

Ref. No. Description Part No.

SW CBA (SUB-B) Consists of the following:

CONNECTOR

CN1062 6PIN FFC WX1E7H50-104 WX1E7H50-104

RESISTORS

R3001 CHIP RES. 1/10W J 300 Ω RRXAJR5Z0301 R3002 CHIP RES. 1/10W J 620 Ω RRXAJR5Z0621 R3003 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102 R3004 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222 R3005 CHIP RES. 1/10W J 6.8k Ω RRXAJR5Z0682 R3008 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103 R3009 CHIP RES. 1/10W J 620 Ω RRXAJR5Z0621 R3010 CHIP RES. 1/10W J 300 Ω RRXAJR5Z0301

SWITCHES

SW3005 TACT SWITCH SKQSAF001A SST0101AL041 SW3008 TACT SWITCH SKQSAF001A SST0101AL041 SW3009 TACT SWITCH SKQSAF001A SST0101AL041 SW3012 TACT SWITCH SKQSAF001A SST0101AL041 SW3013 TACT SWITCH SKQSAF001A SST0101AL041 SW3014 TACT SWITCH SKQSAF001A SST0101AL041

----------

20070307 1-18-5 E7E2AEL

Page 58

All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed, downloaded or stored in any storage medium, in any form or for any purpose without the express prior written consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited.

Information in this document is subject to change without notice. Funai reserves the right to change the content herein without the obligation to notify any person or organization of such changes.

with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way without the express written consent of Funai. All other trademarks used herein remain the exclusive property of their respective owners. Nothing contained in this manual should be construed as granting, by implication or otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights to the fullest extent of the law.

ZC320SL8

E7E2AUD

2007-3-28

Sylvania ZC320SL8, E7E2AUD Schematic

Specifications and Main Features

Frequently Asked Questions

User Manual

IMPORTANT SAFETY NOTICE

SPECIFICATIONS

LASER BEAM SAFETY PRECAUTIONS

IMPORTANT SAFETY PRECAUTIONS

STANDARD NOTES FOR SERVICING

CABINET DISASSEMBLY INSTRUCTIONS

HOW TO INITIALIZE THE DVD RECORDER

FIRMWARE RENEWAL MODE

FUNCTION INDICATOR SYMBOLS

BLOCK DIAGRAMS

SCHEMATIC DIAGRAMS / CBA’S AND TEST POINTS

WAVEFORMS

WIRING DIAGRAM

SYSTEM CONTROL TIMING CHARTS

IC PIN FUNCTION DESCRIPTIONS

LEAD IDENTIFICATIONS

EXPLODED VIEWS

MECHANICAL PARTS LIST

ELECTRICAL PARTS LIST