Sygonix SY-3523494 User guide
Operating instructions
Remote Wall Switch, white color
Item no. 1761747
Up-to-date Operating Instructions
Download the latest operating instructions at
www.conrad.com/downloads or scan the QR code
shown. Follow the instructions on the website.
Explanation of Symbols
The symbol with the lightning in the triangle is used if
there is a risk to your health, e.g. due to an electric shock.
The symbol with the exclamation mark in the triangle is
used to indicate important information in these operating
instructions. Always read this information carefully.
The arrow symbol indicates special information and
advice on operation.
This product must only be used in dry, enclosed indoor
areas. It must not become damp or wet, as this may result
in a fatal electric shock!
Delivery Content
• Remote wall switch
• Battery 12 V/23 A
• Operating instructions
Intended Use
This 2-channel wireless wall switch is designed to turn on and off two
appropriate receivers (e.g. wireless power socket, wireless outdoor
socket, wireless inbuilt switch etc.). In addition, this 2-channel wireless
wall switch has a dimming function (for example, to control a wireless
plug-in dimmer, wireless inbuilt dimmer etc.).
For each control channel, a maximum of 10 receivers can be programmed.
The wireless wall switch is powered by a 12 V battery (type: 23A).
It is intended for indoor use only. Do not use it outdoors. Contact with
moisture, e.g. in bathrooms, must be avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify
this product. If you use the product for purposes other than those
described above, the product may be damaged. In addition, improper
use can result in short circuits, res, electric shocks or other hazards.
Read the instructions carefully and store them in a safe place. Make
this product available to third parties only together with its operating
instructions.
This product complies with the statutory national and European
requirements. All company names and product names are trademarks
of their respective owners. All rights reserved.
Safety Instructions
Read the operating instructions carefully and
especially observe the safety information. If you do
not follow the safety instructions and information on
proper handling in this manual, we assume no liability
for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
a) General
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may
become dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight,
strong jolts, high humidity, moisture, ammable gases, vapours and
solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of
operation and protect it from any accidental use. Safe operation can
no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions
or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even
from a low height can damage the product.
• Check the product for damage before each use! If you notice any
damage, do not use the product any longer! There is a risk of a
life-threatening electric shock!
• Ensure that the insulation for the entire product is neither damaged
nor destroyed. Never disassemble the product! There are no serviceable parts inside.
• Do not use this product in hospitals or medical institutions. Although
the product emits only relatively weak radio signals, these may lead
to the malfunction of life-support systems. The same may also be
the case in other areas.
• Keep the product away from strong magnetic elds generated by
machines, electric motors or loudspeakers.
• Consult an expert when in doubt about operation, safety or connection of the device.
• Maintenance, modications and repairs are to be performed exclu-
sively by an expert or at a qualied shop.
• If you have questions which remain unanswered by these operating
instructions, contact our technical support service or other technical
personnel.
b) Connected devices
• Also observe the safety and operating instructions of any other devices which are connected to the product.
c) Batteries
• Correct polarity must be observed while inserting the battery.
• The batteries should be removed from the device if it is not used
for a long period of time to avoid damage through leaking. Leaking
or damaged batteries might cause acid burns when in contact with
skin, therefore use suitable protective gloves to handle corrupted
batteries.
• Batteries must be kept out of reach of children. Do not leave batteries lying around, as there is risk, that children or pets swallow them.
• All batteries should be replaced at the same time. Mixing old and
new batteries in the device can lead to battery leakage and device
damage.
• Batteries must not be dismantled, short-circuited or thrown into
re. Never recharge nonrechargeable batteries. There is a risk of
explosion!
Installation and Connection
The wireless wall switch is only intended for use in
dry indoor locations.
• Carefully lift the front cover of the
wireless wall switch (e.g. with a
screw driver) and remove it (see
picture on the right).
• Remove the mounting plate. The
mounting plate for the wireless wall
switch is xed to the electronic part
of the wireless wall switch with 4
clamps (see picture on the right).
• The mounting plate has two mounting holes (see the picture on the
right). Remove the mounting plate
and mark the mounting holes on
the wall.
• Drill the holes.
• Attach the mounting plate to the wall,
using suitable mounting material.
• Attach the electronic part of the
wireless wall switch to the mounting
plate.
• Insert a 12V-battery (type: 23A) in
the battery compartment of the wireless wall switch, paying attention to the correct polarity.
• Attach the front plate to the wireless wall switch.
Programming a receiver for the wireless wall
switch
For each control channel, a maximum of 10 receivers can
be programmed.
• Set the receiver to the programming mode. Please follow these operating instructions when so doing.
• Press the desired “I” button on the wireless wall switch to which the
receiver is to be programmed. The programming has been completed successfully.
Deleting programmed receivers from the wireless
wall switch
• Press the buttons “I” and “O” on the wireless wall switch to which the
receiver is programmed. The LED on the receiver starts ashing.
• Now press the button “O” on the wireless wall switch. The LED on
the receiver goes out. The receiver has now been deleted from the
wireless wall switch.
The wireless wall switch’s dimmer function
• Turn on the dimmer, by briey pressing the “I” button on the wireless
wall switch once.
• Press the “I” button on the wall switch again. The dimmer function
is activated.
• Press the “I” button on the wall switch again. The dimmer function
is deactivated.
Start-up, Function Test
Commission the receiver in the correct way (follow the receiver’s operating instructions).
By pressing the appropriate “I” or “O” button on the wireless wall
switch, the receiver is turned on or off.
Transmission range
• The transmission range of the radio signals between the wireless
wall switch and an appropriate receiver is up to 70 m under optimal
conditions.
This value, however, is the so-called “open space
range” (range the transmitter and receiver are visible
to each other, without interfering inuences).
In practical operation, however, there are walls, ceil-
ings of rooms etc. between the transmitter and the
receiver, which reduce the range accordingly.
Due to the different inuences on the radio transmis-
sion, no specic range can be guaranteed.
However, trouble-free operation is usually possible in
a detached house.
The range can sometimes be limited considerably by:
- Walls, reinforced concrete ceilings
- Coated/metallised insulated glass
- Proximity to metal & conducting objects (e.g. radiators)
- Proximity to human bodies
- Broadband interferences, e.g. in residential areas (DECT telephones, mobile phones, radio-controlled headphones, radio-controlled speakers, radio-controlled weather stations, baby phones
etc.)
- Proximity to electric motors, transformers, power-supply units,
computers
- The proximity to improperly shielded or uncovered operating
computers or other electric appliances
Care and Cleaning
The product does not require any maintenance and
should never be opened or disassembled for any reason.
• Only clean the product with a soft, clean, dry cloth.
• Never use aggressive cleaning agents or chemical solutions since
these might damage the surface of the casing or impair the operation.
Declaration of Conformity (DOC)
Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau
hereby declares that this product conforms to the 2014/53/EU
directive.
Click on the following link to read the full text of the EU
declaration of conformity: www.conrad.com/downloads
Select a language by clicking on a ag symbol and enter
the product order number in the search box. You can then
download the EU declaration of conformity in PDF format.
Disposal
a) Product
Electronic devices are recyclable waste and must not
be disposed of in the household waste. At the end of its
service life, dispose of the product in accordance with
applicable regulatory guidelines.
Remove any inserted batteries and dispose of them
separately from the product.
b) Batteries
You as the end user are required by law (Battery
Ordinance) to return all used batteries. Disposing of them
in the household waste is prohibited.
Contaminated batteries are labeled with this symbol to
indicate that disposal in the domestic waste is forbidden.
The designations for the heavy metals involved are: Cd =
Cadmium, Hg = Mercury, Pb = Lead (name on batteries,
e.g. below the trash icon on the left).
Used batteries can be returned to collection points in your municipality,
our stores or wherever batteries are sold.
You thus fulll your statutory obligations and contribute to the
protection of the environment.
Technical Data
Power supply ............................1x 12V battery, type “23A”
Transmission frequency............433.05 - 434.79 MHz
Transmission power..................4.98 dBm
Transmission range .................. Up to 70 m
Internal LED .............................. Lights up briey on the use of the
Programmable receiver ............ a maximum of 10 for each control
Operating temperature .............0 to +35 °C
Dimensions (W x H x D) ...........approx. 80 x 80 x 20 mm
Weight ......................................approx. 48 g (excl. batteries)
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240
Hirschau (www.conrad.com). All rights including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited. This publication represent the technical
status at the time of printing.
Copyright 2019 by Conrad Electronic SE. *1761747_V2_0819_02_mxs_m_en
(in open area, see chapter
“Transmission range”)
buttons
channel
Loading...