Sygonix SY-3523468 User guide

Operating instructions

RSL wireless built-in switch

Item no. 1761733 (Type “RSLR2”)

Item no. 1761734 (Type “RSLR3”)

Latest operating instructions

Download the latest operating instructions via the link www.conrad.com/downloads or scan the QR code shown. Follow the instructions on the website.

Explanation of symbols

The lightning symbol inside a triangle is used when the-

re is a potential risk of personal injury, such as electric shock.

An exclamation mark in a triangle indicates important ins-

tructions in this operating manual that absolutely have to be observed.

The arrow symbol indicates specic tips and advice on

operation.

Delivery content

• RSL wireless built-in switch

• Operating instructions

Intended use

The radio-controlled ush-mounted switch, in combination with a suitable radio-controlled remote switch of the RSL system is used to wirelessly switch a connected consumer load on or off.

The radio-controlled ush-mounted switch is only suitable for operation on the mains voltage (230 V/AC, 50 Hz). A maximum consumer load of 2000 W (Ohm resistive load) or 300 W (inductive load) can be connected.

It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in bathrooms, must be avoided under all circumstances.

For safety and approval purposes, you must not rebuild and/or modify this product. If you use the product for purposes other than those described above, the product may be damaged. In addition, improper use can cause hazards such as short circuiting, re, electric shock etc. Read the instructions carefully and keep them. Make this product available to third parties only together with its operating instructions.

Safety instructions

Read the operating instructions carefully and especially observe the safety information. If you do not follow the safety instructions and information on proper handling in this manual, we assume no liability for any resulting personal injury or damage to property. Such cases will invalidate the warranty/guarantee.

• The device is not a toy. Keep it out of the reach of children and pets.

• Do not leave packaging material lying around carelessly. This may

become dangerous playing material for children.

• Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity, moisture, ammable gases, vapours and solvents.

• Do not place the product under any mechanical stress.

• If it is no longer possible to operate the product safely, take it out of

operation and protect it from any accidental use. Safe operation can no longer be guaranteed if the product:

- is visibly damaged,

- is no longer working properly,

- has been stored for extended periods in poor ambient conditions

- has been subjected to any serious transport-related stresses.

• Please handle the product carefully. Jolts, impacts or a fall even

from a low height can damage the product.

• Also observe the safety and operating instructions of any other devices which are connected to the product.

• The product may only be installed by a qualied technician (e.g. electrician) who is familiar with the relevant regulations (e.g. VDE, German electrical wiring regulations)!

Improper work, carried out on the mains voltage, endangers not only your own life but also the life of others!

If you do not have the expertise required for the installation, do not install it yourself but ask a qualied technician.

• Do not use this product in hospitals or medical institutions. Although the transmitters of the RSL system emit only relatively weak radio signals, these may lead to malfunction of life-supporting systems. The same may be the case in other areas.

• The product may only be operated on the mains voltage (see section “Installation and Connection” and “Technical Data”). Never try to operate the product at another voltage as this will cause its destruction.

• The installation may only be carried out, if all poles of the mains supplies of the wireless ush-mounted switch are disconnected from the mains voltage. Otherwise, there is a mortal danger by an electric shock!

• An all-pole disconnection from the mains voltage (such as a surge protector) must be provided as part of the wiring set-up.

• Never touch the product when your hands are wet or damp! There is a risk of a life-threatening electric shock!

• Only use the product when it is rmly mounted and steady. Insert the product e. g. into a suitable ush-mounted socket or surface box.

• If you have reason to assume that safe operation is no longer possible, disconnect the product immediately and secure it against accidental operation. Neither touch the wireless ush-mounted switch nor any connected device.

Disconnect the wireless ush-mounted switch from the mains voltage by switching off the corresponding circuit breaker or removing the fuse. Furthermore, turn off the earth leakage circuit breaker in order to disconnect all the poles of the mains supply.

Let an expert check the product.

• In commercial institutions, the accident prevention regulations of the employer’s liability insurance association for electrical systems and operating facilities are to be observed!

• Consult an expert when in doubt about operation, safety or connection of the device.

• Maintenance, modications and repairs are to be performed exclusively by an expert or at a qualied shop.

• If you have questions which remain unanswered by these operating instructions, contact our technical support service or other technical personnel.

Preparations for installation

Please observe the chapter “Safety instructions”!

• The wireless ush-mounted switch must be mounted and operated in a suitable ush-mounted socket or surface box, or in another housing suitable for this purpose.

• Only use the wireless ush-mounted switch when it is rmly mounted.

• The radio ush-mounted switch must be disconnected from the power supply during installation. For this purpose, switch off the electrical mains supply by switching off at the corresponding circuit breaker or removing the fuse. Secure it against an unauthorised re-start, e.g. with a danger sign.

Furthermore, turn off the earth leakage circuit breaker in order to disconnect all poles of the mains supply from mains voltage.

• Check that the mains supply is current free with a suitable tester.

Installation and connection

Observe the chapter “Preparations for installation”

• Connect the consumer load to the two middle screw terminals, see picture on the right.

The connection “N” is the neutral conductor, the connection “ ” is the connected output/phase/L.

• The outer two screw terminals are used for the connection to the mains voltage (“N” = neutral conductor, “L” = phase).

• The wireless ush-mounted switch “RSLR2” (item no. 1761733) can be tightened using the lateral fastening eyes (hole distance of the fastening eyes = 60 mm).

The wireless ush-mounted switch “RSLR3” (item no. 1761734) is directly inserted into a ush-mounted socket or surface box.

Pay attention that the push-button on the rear of the housing is exposed during installation and not accidentally pushed.

• The push-button on the rear of the housing is used to “train” or tune the switch to the radio transmitter of the RSL switching system.

Therefore, observe the following chapters before closing the ush mounted socket or surface box and putting the product into operation.

Operation

a) Tuning the wireless ush-mounted switch to a radio trans-

mitter

The radio ush-mounted switch can be programmed to any radio transmitter of the RSL system, e.g. to a radio-controlled wall transmitter or a wireless remote control.

The switch can be programmed to a total of 10 different

radio transmitters of the RSL system. Thus, the wireless ush-mounted switch can e. g. be switched on or off from several locations.

Proceed as follows:

• Press and hold the push-button on the wireless ush-mounted switch (longer than 3 seconds) until the LED next to the push-button starts to blink. The programming mode will be activated for approx. 15 seconds and then exited automatically.

• When the programming mode is activated (LED next to the button ashes), press and hold the “On” key of the radio-controlled wall transmitter (“I” key) or the corresponding “ON” key of a wireless remote control (longer than 3 seconds) until the LED lights permanently and the connected consumer load is turned on.

The tuning process has been completed successfully. The programming mode will be exited automatically.

If you wish to tune the switch to another radio transmitter, the programming mode must be activated rst. Please proceed as described above.

The programming mode will also be activated (LED ash-

es) when the mains voltage is connected (e. g. during initial start-up). Now a radio-controlled wall transmitter or a wireless remote control can be programmed within approx. 15 seconds, see above.

b) Disabling a programmed, wireless ush-mounted switch from

a radio transmitter

If you wish to use the switching channel of a radio-controlled transmitter (radio wall switch or wireless remote control) e. g. for another wireless ush-mounted switch, this channel can be released as follows:

• For approx. 3 seconds, press and hold the two operating keys of your radio-controlled transmitter for the “On” and “Off” function of the switching channel that you wish to release.

- Wireless wall switch: Press the “I” and “O” keys simultaneously for more than 3 seconds.

- Radio remote control: Press the “ON” and “OFF” keys simultaneously for more than 3 seconds.

• The LED on the wireless inbuilt switch starts blinking. The programming mode is now activated for approx. 15 seconds and afterwards, will be exited automatically.

• Press and hold the “O” key on a wireless wall switch or the “OFF” key of the corresponding switching channel on a wireless remote control for at least 3 seconds.

• The LED on the wireless wall switch goes out.

• This disables the connection between the radio-controlled

ush-mounted switch and the radio-controlled transmitter. Now the radio-controlled inbuilt switch does no longer react to the corresponding radio transmitter.

Observe the operating instructions for the radio-controlled

transmitter of the RSL system you are using.

c) Switching on/off via the push-button on the wireless

ush-mounted switch

• For a function test the consumer load connected to the wireless inbuilt switch can also be switched on and off using the push-button.

• Briey press the button on the wireless ush-mounted switch to turn the consumer load on (LED on the switch lights up) or off (LED goes out).

Function test

• If haven’t already programmed the wireless ush-mounted switch, you have to program or tune it to a radio transmitter of the RSL system (e. g. to a radio-controlled wall switch or a wireless remote control).

• Make sure that the wireless inbuilt switch is supplied with mains voltage (230 V/AC, 50 Hz).

• Press the “I” button on the radio-controlled wall switch or the switching channel’s “ON” button of a radio remote control to which the wireless inbuilt switch was tuned.

The red LED on the wireless ush-mounted switch lights up and the switching output will be activated and a connected consumer load switched on.

• To deactivate the switching output and to switch off the consumer load, briey press the “O” button on the radio-controlled wall switch or the switching channel’s “OFF” key of the a wireless remote control to which the inbuilt switch was tuned/programmed.

The red LED on the wireless inbuilt switch goes out.

Information about the range

Depending on the radio transmitter of the RSL system used, the range is up to 70 m.

This value, however, is the so-called “open space range”

(the range the transmitter and receiver are visible to each other, without disturbing inuences).

In practical operation, however, there are walls, the ceil-

ings of rooms etc. between the transmitter and the receiver which reduce the range correspondingly.

Due to the different inuences on the radio transmis-

sion, no specic range can be guaranteed. However, trouble-free operation is usually possible in a detached house.

The range can sometimes be limited considerably by:

• Walls, reinforced concrete ceilings

• Coated/vapour-deposited, metallized insulating glass panes

• Proximity to metal & conducting objects (e.g. radiators)

• Proximity to human bodies

• Broadband interferences, e.g. in residential areas (DECT tele-

phones, mobile phones, radio-controlled headphones, radio-controlled speakers, radio-controlled weather stations, baby phones etc.)

• Proximity to electric motors, transformers, power-supply units, computers

• The proximity to improperly shielded or uncovered operating computers or other electric appliances

Care and cleaning

The product does not require any maintenance and should never be opened or dissembled for any reason. Repair or maintenance work must be carried out by a specialist.

Declaration of Conformity (DOC)

Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau hereby declares that this product conforms to the 2014/53/EU directive.

Click on the following link to read the full text of the EU

declaration of conformity: www.conrad.com/downloads

Select a language by clicking on a ag symbol and enter

the product order number in the search box. You can then download the EU declaration of conformity in PDF format.

Disposal

Electronic devices are recyclable waste and must not be

disposed of in the household waste. At the end of its service life, dispose of the product according to the relevant statutory regulations.

You thus full your statutory obligations and contribute to

the protection of the environment.

Technical data

Operating voltage ....................230 V/AC, 50 Hz

Switching capacity ................... 2000 W (resistive load)

300 W (inductive load)

Consumer loads with mainly resistive load are e.g. light

bulbs, heaters etc.

Devices with inductive load are e.g. engines, control

Reception frequency ................ 433 MHz

Transmission range ................. max. 70 m (see chapter “Range”)

Ambient temperature ............... 0 to +35 °C

Dimensions (W x H x D) ..........Type “RSLR2”: 68 x 48.5 x 25 mm

(Item no. 1761733, with fastening

Type “RSLR3”: 48.5 x 48.5 x 25 mm

(Item no. 1761734, without fastening

Weight ..................................... approx. 37 g

gears, conventional transformers, energy saving light sources etc.

eyes)

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent the technical status at the time of printing.