SWIT Electronics CM-55C Quick Manual

QUICK GUIDE

5.5″ 4K HDMI Monitor

CM-55C

INTERFACES AND BUTTONS

Power Switch

DC IN

Battery Input

BATT OUT

HDMI IN

Remote

Switch to“

|

”position to power on;

and switch to “

o” position to power off

DC power input, 5～17VDC，Micro USB

External battery NP-F or LP-E6, 6V～8.4V

Battery output

HDMI input interface
compatible DVI1.0, HDMI Type-A

Remote control, headphone output,

2.5mm Stereo Jack
Headphone output jack, 3.5mm stereo Jack
SD card slot, the SD card is used to load the

customized LUT tables, and update the
monitor firmware.

SD Card Slot

Remote Control

HDMI Input

Power Switch

DC Power Input
Micro USB

Headphone

Battery Input
Battery output

❶ Install the battery or connect the power cord.

❷ Switch the power switch to “一”position, the monitor will

be powered on.

*

It will display the boot screen after power on for 3~4 seconds.

*

The BATT OUT interface directly outputs battery power when

battery is mounted.

*

Only use the adapter and the power cord specified by the

manufacture for your safety!

POWER ON

Joystick

Joystick provides five operation directions, Up Down, Left,
Right, and Straight Down. Use the joystick as a navigation
tool to scroll between scenes pages and set features.

BUTTONS OPERATION

: scroll it leftmost to enter into the monitor settings menu

: scroll it right to enter into a scene or create a scene mode

: scroll it up to enter into ZOOM mode

: cancel the settings, return to the previous menu or quit

menu settings.

: scroll it down to confirm the current operation or selection

JOYSTICK

SCENE MODE

Enter a Scene

It will display a scene as default after powered on. Scroll the
joystick right or left to switch among scenes.
Scroll the joystick down to return a scene when in ZOOM mode.
Scroll the joystick right to return a scene when in monitor
settings menu.

Add a Scene

Hold the joystick right for 3 seconds, it will prompt “Add
New MySet ” command in the bottom center of the
screen, press the joystick straight down to confirm the
operation. It supports up to 8 customized scenes.
The scene will be numbered in sequence, and the name will
be displayed at the left bottom of the screen, e.g., .

Delete a Scene

Scroll the joystick down in a scene, it will display the DELETE
command at the bottom of the screen, press the joystick
straight down to confirm deletion. The DELETE command is
not available when there is only one scene.

SCENE TOOL

Add a Tool in a Scene

In a scene, scroll the joystick down, it will pop up the “ADD
NEW TOOL” command. Press the joystick straight down to

confirm, it will display Tools Menu on the left side of the
screen, scroll the joystick up or down to select your desired
scene tool, and press the joystick straight down to confirm.

Enable/Disable a Tool

In a scene, press straight down the joystick to display the
scene tool, and then scroll the joystick left to close the
scene tool in current scene.

IMAGE ZOOM

Scroll up the joystick to enter into image zoom mode,
double(2X) or quadruple(4X) the image, and move the
starting position of the enlarged image.

❶ Enter ZOOM Mode

In a scene, scroll up the joystick to enter into image zoom
2X mode, and there will be a 2X zoom icon at the right
bottom corner of the screen, continue to scroll up the
joystick to to enter into image zoom 4X mode.

Scroll Up Once

Scroll Up Twice

❷ Adjusting Mode

Press straight down the joystick to move the starting
position of the enlarged image.

Then, the icon is changed, there will be four arrows at each
direction surrounding the center rectangle.
Press straight down the joystick to confirm the adjustment.

*

In 2X or 4X zoom mode, press straight down the

joystick, it will recover and display the original image.

Rotate Screen

Hold the joystick left for 3 seconds to enter the monitor
settings menu;
Scroll down to select controls→DISPLAY ROTATE item,
and press straight down the joystick to display the

DISPLAY ROTATE submenu. Scroll right or left to set the
SCREEN ROTATE item to be 180, then the input image will
reverse vertically. Set the IMAGE ROTATE as the same way.

Restore the Factory Settings

Select monitor settings menu, and select system→
FACTORY RESET item, then scroll right to select EXECUTE
FACTORY RESET command, and press the joystick straight

down to confirm the selection to initialize the settings to
default values.

SWIT Electronics Co., Ltd.

Add: 10 Hengtong Road, Xin'gang, Nanjing Economic and
Technological Development Zone, Nanjing 210038, P.R.China
Tel: [phone] Email: [e-mail]

SWIT Electronics Europe GmbH

Add: Hochstr. 17, 47228 Duisburg, Germany
Tel: [phone] Email: [e-mail]

SWIT Electronics America, Inc

Add: 3350 Scott Boulevard 61-02, Santa Clara, CA 95054, USA
Tel: [phone]-SWIT(7948) Email: [e-mail]