SWIT FM-215HDR Users Guide

SWIT ELECTRONICS CO., LTD.

4K input FHD Broadcast Monitor

Model：FM-215HDR

Contrast

Saturation

Brightness

User2

User3

User1

User4

Info/Quit

Backlight

Volume

USB/Firmware

Menu/Enter

Source

Power

Phone

User Manual

Please read this user manual throughout before using

Ver：A

01

01

Declaration

Any internal technology (including hardware equipment, software design and product trademark)
of the product shall be protected by law, and any infringement of intellectual property rights of the
product shall be investigated for legal liability。

All the brand and trademark in this product are protected by law,all other company’s brand and
trademark in this product are protected by their owner’s law.

In order to better service majority users,SWIT products will keep improving and developing,SWIT
keep the right to revise and improve this user manual without previous notice.

The warranty period of this product are two years,the following condition are not covered by the
warranty:

⑴ The appearance and the LCD panel are damaged by man-made out force；
⑵ The amount of defective pixels are under three；
⑶ Damage the product by using incompatible power adaptor；
⑷ Damage the product due to violation operation；
⑸ Disassemble the product when using；
⑹ Other faults or damages not caused by design ,technology,manufacture and quality.

＊ Any sales person have no right to provide extra warranty beyond these terms.

If you have any advises or requirements about our products during using,please feel free to contact
with us via phone or E-mail.

This instruction manual applies to FM field monitors and the schematic is based on the exterior

＊

view of the FM-215HDR as an example. Any differences in specifications and appearance are
explained in additional text in this manual.

SWIT Electronics Co., Ltd.

Address: 10 Hengtong Road, Nanjing Economic and Technological Development Zone,
Nanjing 210038, P.R.China
Phone: [phone]
Fax: [phone]
Email: [e-mail]
http://www.swit.cc

02

Maintaince percautions

Warning

1. To reduce the dangerous of fire or electric shock,do not expose the monitor in raining or wet place.

2. The monitor will create noise when using near high-intensity magnetic field.

Precautions for power supply

1. Please use the special power adapter specified by the original factory to avoid damage to the product.

2. If other DC power supply is used, ensure that the voltage range, power supply and polarity of the

power supply meet the requirements.

3. In the following cases, please unplug the power cord and external battery of the product:

(A) If you have not used the product for A long period of time.

(B) If the power cord or power plug/socket is damaged.

(C) If the product is hit or dropped so that the shell is damaged.

Precautions for product use

1. Please do not touch the screen surface directly with your fingers to avoid damage to the screen,

and the oil on the skin will be difficult to remove if left on the screen.

2. Please do not put pressure on the LCD screen, LCD screen is very delicate and fragile.

3. Do not place the product in an unstable place, as the product may be seriously damaged due to falling.

Precautions for product cleaning

1. Clean LCD screen, please use dry soft fabric with fluff and special liquid crystal cleaning agent,

to remove dust and stains on the screen.

2. Do not pressure when wiping the LCD screen surface.

3. Please do not use water and other chemical cleaners to wipe the LCD screen surface,

chemical agents may damage the LCD screen surface.

03

Content

Declaration

Maintaince percautions

Content

Packing list

Introduction

Operation Instructions

Front panel

Back Panel

Flight Case

OSD

Menu Configuration

1. Exit & Status - Exit the main menu and display the current status of the monitor.

2. Input—Set the color of input video

3. Image setting—Setting for the picture preference

2

3

4

5

5

6

6

8

9

9

12

12

13

13

4. Color management—Setting about video colors

5. Scanning—Setting for picture scan, zoom, etc.

6. Control—Setting for TALLY, UMD, IP control to the monitor

7. Assist-Setting for Vector scope and Histogram patterns.

8. De-embed—Setting for video/audio analysis functions.

9. Auto calibration

10. System-User profile saving,firmware update.

11. Multiview setting

Appearance and Size

Specification

Supported standards: Signals of the following standards can be displayed on the monitor

Common Problems and Solutions

14

15

16

18

20

21

23

26

27

28

29

30

04

Packing list

No.

1

2

3

4

Standard accessories

Monitor

Aluminium flying case

Battery plate（V-mount & Gold-mount）

Power cable

Quantities

X

1

X

1

X

1

X

1

Introduction

This series of monitor adopts TFT-LCD thin film transistor + QLED quantum dot display composition,
the resolution is up to 1920x1080, H178°/V178°

1 channel 12G/6G/3G/H D/SD-SDI input
3G/HD /SD-SDI input and 1 channel

4-channel or 2-channel simul

taneous picture display with headphone and speaker outputs .

and output, 1 channel HDMI® 2.0 4K@60 inpu t, and 3 channels

3G/HD/SD-SDI output, quad-link 4xSDI SQD /2SI 4Kp60/p50 inpu t

ultra-wide viewing angle, 1000:1 contrast ratio, support

Features:

21.5" 1920X1080 Full HD QLED screen.
1000nits high brightness backlight HDR monitor.

s,

97% DCI-P3 wide colour gamut ratio.
4K/UHD interface (1x12G-SDI in/out, 1x HDMI® 2.0 4K@60 input).
12GSDI, HDMI® Mixed Quad, Dual PBP and PIP Picture-in-Picture monitoring.
12GSDI, HDMI® dual-screen PBP vertical monitoring.
Simultaneous display of HDR/SDR in multi-colour gamut for one signal.
Read Payload ID to automatically set quantisation, dynamic contrast, colour gamut, etc.
18bit high precision internal signal processing.
Zero audio/video delay (0.01 frame).
Built-in DelogSDR/HDR table for multiple cameras.
16-channel audio d

e-embedded sound column display, optional 2-channel output.
Lissajous, 5.1 stereo phase map.
Support waveform selection display Y/Cb/Cr/R/G/B /RGB and single line selection mode.
Vector scope, R/G/B/Y histogram, bi-color focus assist.
3DLUT（17 x 17 x 17） accurate color correction, Fully automatic colour correction, no computer
required.
User 3DLUT uploaded via USB.
UMD dynamic source name and soft TALLY display (TSL 3.1/4.0), GPI control interface.
Composition ratio auxiliary line:4:3/13:9/14:9/15:9/16:9/1.85:1/2.35:1/2:1/2.39:1/Custom 1/Custom 2.
Support USB firmwa

re upgrade and import Log file.(USB file system supports FAT 32 format only).
IP Webserver Web Control.
Support ECO mode.

05

Operation Instructions

Front panel

(1)

(10)

Brightness

Contrast

Saturation

User1

User2

User3

Backlight

User4

Info/Quit

USB/Firmware

Menu/Enter

Source

Volume

Power

Phone

Contrast

Volume

(5)

Saturation

Source

Menu/Enter

(6)

USB/Firmware

(7) (8)

Phone

Power

(9)

(2)

User1

User2

(3)

User3

User4

Info/Quit

(4)

Brightness

Backlight

(1) Speaker: For SDI/ HDMI® embedded audio. (Will not work if earphone is plugged in)

(2) F1~F5 function keys: Customize shortcut function keys. Users can set the shortcut

keys to different functions according to their own requirements.

(3) User1~User4：U1~User shortcut key, which can be used to quickly enter the set user

mode. Long press to save user settings. Please see details in “10. System”

(4) Info/Quit：Display setting item. Press " Info/Quit " button to display or turn off relevant

status information and audio and video analysis function graph. When opening the

menu, press " Info/Quit " to exit the menu with one click

06

(5)

Brightness: Adjust the brightness. -100~100 adjustable,
default value is 0.

Brightness

Contrast

Saturation

Contrast: Adjust contrast. -100~100 adjustable,
default value is 0.

Saturation: Adjust saturation. -100~100 adjustable,
default value is 0.

Backlight

Volume

Source

Backlight: Adjust the backlight. 0~100 adjustable, default
value is 16.

Volume：Adjust the volume.0~100 adjustable,
default value is 36.

Press Brightness, Contrast, Saturation, Backlight, Volume five shortcut keys confirm to select
this option, and rotate Menu to adjust the corresponding item value directly. Press the button
and automatically cancel the selection without operation within five seconds, and the button
light will be off, long press to restore default values；Adjust the volume.0~100 adjustable, the
default value is 36.Long press the volume button to mute.

Source

SDI 1

Source：Select the input source signal format.

SDI 2
SDI 3
SDI 4

4xSDI SQD：Supports quad-link 4Kp60/p50 inputs
4xSDI 2SI：Supports quad-link 4Kp60/p50 inputs

4xSDI SQD
4xSDI 2SI
HDMI®
Multiview

(6) Menu/Enter：When no Menu is displayed, press the button directly to open the Main Menu;

Rotate the knob to select different settings or adjust parameter values, press the knob to set；

(7) LUT/Firmware: Update firmware or import LUT files，Auto Calibration；

(8) PHONE: 3.5mm headphone jack is used to monitor the embedded audio signals of SDI and

HDMI®;

(9) Power: Power switch;

(10)Aluminium alloy flight case: to hold the monito.

07

Back Panel

(1)

(2)

(3)

ETHERNET

HDMI IN

2.0

(4)

(5)

(6)

RS485OUT

GPI IN

RS485IN

(7) (8) (9)

(1) SDI1 OUT：12G/6G/3G/HD/SD-SDI

SDI2 OUT：3G/HD/SD-SDI

(2) SDI1 IN：12G/6G/3G/HD/SD-SDI

（12）

(11)

(10)

SDI2~4 IN: 3G/HD/SD-SDI

(3) ETHERNET(Network interface)：1000M high-speed RJ45 Ethernet port，

for web external control

(4) HDMI® 2.0 4K@60 in：Will not display HDCP protected content

(5) RS485：TSL UMD control port

(6) GPI：GPI control port

(7) Fan

(8) VESA bracket mounting area

(9) DC IN：12V~17V

(10) AC switch: turns AC power on or off

(11) AC IN：100V~240V

(12) Battery grommet mounting area

08

Flight Case

(1)

(2)

（1） Flight case adapter plate:

OSD

(4)

(5)

(6)

(7)

(2)

(3)

(1)

(3)

can be used to secure other

equipment (e.g., PTZ, wireless

transmission equipment, etc.)

（2） Flight case handle

（3） Rubber cushion for luggage base

TC 00:15:13:07

CAMERA 1

Before Calibration After Calibration

400mV

R

R

R75

R75

Mg

Mg

Mg75

Mg75

B

B

B75

B75

Cy

Cy

0.8
G

R

0.6

G

0.4

0.2

B

Y

Y

DCI-P3

R

B

0.2

0.4

0.6

0.8

940

768

512

256

64

Cy75

Cy75

G

G

G75

G75

YI

YI

YI75

YI75

W

W

Delta = 0.9

Delta = 2.3

200mV

-200mV

-400mV

C

L

R

Rs

Ls

-

10

U

U

U

U

U

U

U

U

N

N

N

N

N

N

N

in phase

L

R

1 2

N

L

L

L

L

O

O

O

O

M

M

M

M

M

M
U
T
E

3 4 5 6 7 8 910111213141516

L -32DB 01CH

C

C

C

C

U

U

U

U

U

K

K

K

K

T

T

T

T

T

E

E

E

E

E

E

E

E

E

D

D

D

D

R -13DB 02CH

L

L

L

L

-

20

O

O

O

O

C

C

C

C

-

30

K

K

K

K

E

E

E

E

-

40

D

D

D

D

-

50

60

-

(13)

(12)

(11)

Contrast

Saturation

Brightness

User1

User4

USB/Firmware

Menu/Enter

Source

Volume

Backlight

Info/Quit

User3

User2

Power

Phone

(8) (9) (10)

09

(1) TALLY Light

TALLY Light Controlled by GPI

(2) Time Code(SDI)

Under SDI input, the monitor can display Time code information (LTC, VITC1&2). If no Time
code info is detected, it will display “TC UNLOCKED”. User can set function keys F1～F5 or GPI
pins as “Time Code” to turn on or off this function.

(3) On screen TALLY

Control of the display signal via GPI

(4) Source ID/UMD

Display /UMD（TSL3.1/4.0），user can set in the UMD menu

(5) Colour gamut char

Used to monitor the colour fullness and fineness of the image, open the gamut chart to
display the current video gamut, users can set the "Main Menu" - "Colour Management" ­"Gamut". Current colour gamut.

(6) Histogram

The horizontal axis of the histogram indicates the brightness of the image, from left to right
indicates the increase of brightness, the left side represents the darker area, the right side is
the brighter area, the vertical axis of the histogram indicates the distribution of the number of
pixels, the higher the vertical coordinate, the higher the brightness density.
The vertical axis of the histogram represents the distribution of the number of pixels, the
higher the vertical coordinate, the higher the luminance density, users can set the front panel
shortcut keys (F1~F5) or GPI pins to the "Histogram" function, to turn on/off this function.

(7) Waveform

Used to display multiple signals sampled at the same rate, users can set the front panel short­cut keys (F1~F5) or GPI pins to the " Waveform " function to turn on or off the Waveform graph
and select different types of Waveform graphs; the parameters of the Waveform graph, such
as the position, transparency, color, etc. are set in the " Waveform Setting" submenu. Wave­form parameters, such as position, transparency, color, etc., can be set in the " Waveform
Setting" submenu.

(8) Vectors

Used to monitor the colour, shape, outline, size and position of the image, etc. Users can set
the front panel shortcut keys (F1 to F5) or GPI pins to the "Vector Graphics" function to turn
on/off this function, and the display position, colour, transparency and other related parame­ters of the vector graphics are set in the "Vector Graphics Settings" submenu.

10

(9) Lissajous

Used to monitor the audio frequency analysis and phase amplitude difference determination,
the user can set the front panel shortcut keys (F1~F5) to "Li Sha Yu" function, open/close this
function.

(10) Audio Meter

Used for monitoring audio information, users can set the front panel shortcut keys (F1~F5) or
GPI pins as the function of "Audio Meter" to turn on/off this function, the display position of
the audio meter, the number of displayed channels, transparency and other related parame­ters are set in the Audio Settings sub-menu.

(11) Surround Phase

Monitor the sound source location of the full-space stereo sense of knowledge, Surround
Phase default 5.1, the default 7, 8 channels, the user can be in the menu "data de-embedding"

- "left / right channel", set the desired sound channels

(12) Eye pattern

Used to monitor the strength of the SDI signal quality, the larger the eye chart image, the
stronger the signal quality.

(13) Colour checklist

After auto calibration, the gamut value and colour difference (△E) before and after calibration
will be popped up. "Auto calibration"-"Measurement" pops up the gamut value and colour
difference (△E) of the last calibration and the current measurement.

Button operation

1.Press the "Menu/Enter" knob, the menu pops up in the upper left corner of the screen, and the
currently selected menu is highlighted in yellow.

2.Rotate the "Menu/Enter" knob to select all kinds of sub-menu, the corresponding item is high­lighted in yellow, press the "Menu/Enter" key, the sub-menu is selected and enter the parameter
setting sub-menu.

3.Rotate the "Menu/Enter" knob to select the item to be adjusted, press the "Menu/Enter" knob,
the adjustment items and parameters are highlighted in yellow.

4. rotate the "Menu/Enter" knob to adjust the parameters, complete the settings, click
"Menu/Enter" to save the settings.

5.Rotate "Menu/Enter" to select "Exit", click "Menu/Enter" knob to exit the sub-menu, select "Exit
& Status" in the main menu. Select "Exit & Status" in the main menu, click the "Menu/Enter"
knob to exit the main menu.

Note

1. Items displayed in grey cannot be set;

2. If there is no operation within the set time, the menu will automatically save the settings and
exit.

3. If the key lock function has been turned on, all items except "System Setting" will be displayed
in grey, if you want to adjust any item, please set the key lock function to "Off" first.

11

Menu Configuration

Menu configuration introduces the main menu and the sub-menu, marked * menu items will be
given in the list after a more detailed description of the menu or the operation of the explanation

1. Exit & Status - Exit the main menu and display the current status of the monitor.

Main Menu

Exit&Status
Input

Picture
Color Management
Scanning
Control

Assist
De-embed
Auto Calibration
System
Multiview Setting >

Format
Source

>

Color Temp

>

F1

>

F2

>

F3

>

F4

>

F5

>

Profile Type

>

Version

>

Status

XX
XX
XX

XXX
XXX
XXX
XXX

XXX
XX
XX

(1)

(2)
(3)
(4)

(5)
(6)

Press "Menu/Enter" key, the main menu pops up in the upper left corner of the screen, and
the main menu shows the current working status of the monitor.

(1) Standard

Display the standard of the current input signal; if there is no recognisable signal input, "No
Signal" will be displayed. If you select Multi-screen for the current channel, and select
4-screen, 2-screen or Picture-in-Picture for the Multi-screen type, the standard will display
the input signal standard of the screen 1/2/3/4 or screen 1/2 channel respectively.

(2) Input source

Displays the currently selected channel.

(3) Colour Temperature

Displays the currently set colour temperature mode

(4) Function key 1~Function key 5

Displays the currently set function value of the function key

(5) Model

Displays the current monitor model

(6) Version

Displays the current software version number

12

2. Input—Set the color of input video

Menu Item

Menu description

Value

Full 0-1023、

Input Range*

1

Set the input range of input video

SDI Full 4-1019、
Limited 64-940

Red Gain
Green Gain

Blue Gain
Red Bias
Green Bias
Blue Bias
Reset

Adjust Red Gain
Adjust Green Gain
Adjust Blue Gain
Adjust Red Bias
Adjust Green Bias
Adjust Blue Bias
Reset the gain and bias values of the settings

-100 ~ +100

-100 ~ +100

-100 ~ +100

-100 ~ +100

-100 ~ +100

-100 ~ +100
/

*1 Input Range: Sets the quantization range of the video to suit the input video signal.
The default video quantization range is Limited 64-940 for the broadcast application

*1

3. Image setting

—Setting for the picture preference

Menu item

Contrast

Brightness

Saturation

Sharpness

Backlight

Menu description

Adjust contrast

Adjust brightness

Adjust saturation

Adjust sharpness

Adjust backlight

Value

-100 ~ +100

-100 ~ +100

-100 ~ +100

0 ~ +100

0 ~ +100

*1 Image Settings

The image settings for contrast, brightness, saturation and backlight can be quickly adjust­ed using the front panel shortcut keys.

13

4. Color management—Setting about video colors

Menu item

Color gamut
Gamma

Gamut and
gamma
values are
set to menu
items with
specific
values

Partition HDR/SDR

Color temp

*1

*2

HLG System
Gamma

D-Log to 709

D-Log to PQ

D-Log to HLG

Menu Description

Set gamut values
Set gamma values

*3

*4

Set HLG System Gamma

Set gamut to Rec.709 camera table

Camera table when gamut is set to
Rec.2020 and gamma value is PQ1000

Camera table when gamut is set to
Rec.2020 and gamma value is HLG1000

Partition HDR/SDR on，off

Set screen display colour temperature
values

Value

LCD Native,DCI-P3,Rec.709,Rec.2020

1.0,1.8,2.2,2.4,2.6,PQ1000,HLG1000,S-Log3

1.0,1.1,1.2（default）,1.3,1.4,1.5

OFF,J-Log1,Log-C,S-Log2,C-Log,V-Log,RedLogFilm,
S-Log3,User-Log

OFF, ARRI_LogC_PQ,Canon_CLog2Cin_PQ
Canon_CLog3Cin_PQ,Panasonic_VLog_PQ,
RED_L3G10_PQ,Sony_SLog3_Cin_PQ,
Sony_SLog3_SG3_PQ

OFF,ARRI_LogC_HLG,Canon_CLog2Cin_HLG
Canon_CLog3Cin_HLG,Panasonic_VLog_HLG,
RED_L3G10_HLG,Sony_SLog3_Cin_HLG,
Sony_SLog3_SG3_HLG

OFF,ON

D55，D65，D75，D93，DCI，USER1，USER2

Set the user color temperature value

User temp

G/M

LUT Upload

Calibration LUT Reset

*5

when the color temperature mode is

”2RESU/1 RESU“ sa detceles

Set the user color temperature value
when the color temperature mode is

”2RESU/1 RESU“ sa detceles

Select the cube file you want to import

Select the appropriate cube file to
restore to factory settings

4000K~9800K

-100 ~ +100

None，3DLut.cube，User-Log.cube

NO，3DLut.cube

*1 Color gamut

Set the gamut to match the input video.

*2 Gamma

When Four-screen is selected; the gamma of four signals can be adjusted separately for display

*3 HLG System Gamma

Display tunable only when Gamma is set to HLG1000

*4 Partition HDR/SDR

Individual colour gamut for Partition HDR/SDR, gamma can be adjusted individually, Partition
HDR/SDR default colour gamut Rec.2020, gamma 2.2.

*5 LUT Upload

Place the cube file that needs to import the monitor in the root directory of the u-disk, insert the
u-disk into the USB interface on the front shell of the monitor, and choose to import the corre­sponding file

14

5. Scanning—Setting for picture scan, zoom, etc.

Menu Item

Scanning

Zoom -in

Freeze Frame
Odd/Even Frame

*1

*2

Menu Description

Set up a scanning mode that matches the audio to
the screen

Set a zoom mode

Select an image still mode

*3

Set to open odd field or even field

Value

Pixel To Pixel, Panel Fit

OFF, Top Left, Top, Top Right, Left, Center,
Right, Bottom Left, Bottom ,Bottom Right

OFF, ON
OFF, Odd Frame, Even Frame

*1. Scanning

Panel Fit: Turn on this feature to adapt the video to the entire screen.

Pixel To Pixel only displays the original mode in the specified mode.
*2. Zoom -in: Shown below, the image is divided into 9 regions and adjusted to display in
sequence.

When the zoom mode is turned on, a rectangle box pops up at the bottom left of the screen,
showing the currently selected zoom image area.

*3.Odd/Even Frame

Odd/Even Frame is only displayed in I mode. Open Low Latency Mode and Odd/Even Frame
function is turned off.

15

6.Control—Setting for TALLY, UMD, IP control to the monitor

Menu Item

GPI Control

GPI 1Pin

GPI 2Pin

GPI 3Pin

GPI 4Pin

GPI 5Pin

GPI 6Pin

Tally Setting

Tally Position

F1

F2

F3

F4

F5

*2

UMD

Menu Description

*1

Open or close GPI Control

Set the function of each
pin for GPI terminal

Switch on/off Tally light
Set the display position of On

Screen Tally Lamp

Set the control function of the
function key

Open or close UMD display

Value

OFF,ON

SDI1, SDI2, SDI3, SDI4, 4×SDI 2SI、
4×SDI SQD, HDMI®, Red Tally, Green Tally,
Yellow Tally ,Time Code, Freeze Frame,
WFM Type, WFM Single Line, UMD,
Marker , Waveform, Audio Bar, Zebra,
Vector, Low Latency Mode, Histogram,
Focus Assist , False Color

OFF, ON, Blinking

Top, Bottom

Time Code, Color Temp, Freeze Frame ,
Waveform, Waveform Type , UMD, Marker,
H/V Delay, Blue Only, Audio Bar, Zebra,
Vector, Low Latency mode, Histogram,
Odd/Even Frame , Focus Assist ,False
Color,CIE
OFF, ON

UMD Color
UMD Position
UMD Size

UMD Blending

Set the color of UMD characters
Set the position of UMD characters
Set the size of UMD characters
Show the transparency of the UMD

background

Display Type

Set display UMD or source name
characters

*3

RS485 Address
Baud Rate

Source ID

Set the location of RS485
Fixed for 115200
Set the character that the source

name displays

*1 GPI control

Connect the GPI remote control terminal

through the GPI interface on the real panel

the function of GPI 1-6 buttons.

White,Red,Green,Blue,Black,Gray
Top,Bottom

Large, Small

OFF, LOW, HIGH

Source ID, TSL3.1,TSL4.0

1~126

115200,8,n,1/38400,8,n,1/ 9600,8,n,1
A-Z, a-z, 0-9, [\]^_`{l}~@?>=<,,/.-+*

()’&%$#’’!

GPI 1
GPI 2
GPI 3
GPI 4

GPI 5

tes dna ”lortnoc IPG“ no nrut ,rotinom eht fo

GPI 6

NC

GND

The GPI control allows you to control both the Tally light and the on screen TALLY light on at
the same time:

16

On Screen Tally
Red/Green/Blue

Tally Lamp

Red/Green/Blue

Contrast

Saturation

Brightness

USB/Firmware

Menu/Enter

Source

User2

User3

User1

User4

Info/Quit

Volume

Backlight

Phone

On Screen Tally
Red/Green/Blue

Power

*2 UMD

Select the display type as ““TSL3.1or 4.0”, which can be controlled with TSL UMD.

1

2
3
4

5
6
7
8

1

2
3
4

5
6
7
8

RS485 IN

RS485 OUT

Pin No

1
2
3
4
5
6
7
8

RS 485 IN

GND

NC

RXD-

NC
NC

RXD+

TXD-

TXD+

RS 485 OUT

GND

NC

RXD-

NC
NC

RXD+

TXD-

TXD+

Cascade:

*3 RS485 address

When Multi-screen-"4-screen or 2-screen" is selected, if screen 1/2/3/4 or screen 1/2 are set to
different addresses, the UMD of a single screen can be controlled separately

17

7. Assist-Setting for Vector scope and Histogram patterns.

Menu Item

False Color

Blue Only

Focus Assist

Zebra

Waveform

Vector

CIE

Waveform

WFM Type

WFM Position

WFM Blending

WFM Brigh

WFM Color

WFM Single Line
WFM Line Count

Vector

Vector Position

Vector Blending

Vector Brigh

Vector Color

CIE

CIE Position

CIE Blending

CIE Bright

CIE Color

Menu Description

Turn false color display on or off

Turn blue only on or off

Turn on or off focus assist and adjust the
color of the focus assist

Turn zebra on or off

Turn waveform on or off

Set the WFM Type

Set the WFM position

Value

OFF, ON

OFF, ON

OFF, Blue, Red

OFF, ON

OFF, ON

Y, Cb, Cr, R,G,B,RGB
Bottom Left, Bottom

Right, Top Left, Top Right

Set the blending of the background color of the
waveform

Set the brightness within a WFM image

Set the color of the waveform displayed on the
waveform chart

*1

Switch on single line waveform
Set a line for the single line waveform
Turn vector on or off

Adjust the position of the vector on the screen

Vector scope transparency selection
Set the brightness within a vector image
Set vector colors

Turn the colour gamut chart on or off

Adjusting the position of the colour gamut map on
the screen

Set the transparency of the background colour of
the colour gamut map

Set the brightness within the colour gamut map
chart

Set gamut map colours

OFF, High, Low

Low, Medium, High

White, Green, Color

OFF, ON
1-1080
OFF, ON
Bottom Left, Bottom

Right, Top Left, Top Right
OFF, LOW, HIGH

Low, Medium, High

White, Green, Color

On,Off
Top left, Top right, Bottom

left, Bottom right

Off, Low, High

Low, Medium, High

White, green, colour

Histogram

Marker

Eye pattern

Histogram

Histogram Position

Histogram Blending

Marker

Marker Select

Horizontal(user 1)
Vertical(user 1)
Horizontal(user 2)

Vertical(user 2)

Safety area

Fit Marker

Center Marker

Marker Color

Marker type

Marker outside

*4

Turn histogram on or off

Set the display position on the histogram screen

Set the transparency of histogram background color

Turn marker on or off

Set the scale of the market line

*2

Set the X ‒ axis value of the marker

Set the Y ‒ axis value of the marker

*3

Set the X ‒ axis value of the marker

Set the Y ‒ axis value of the marker

Set safety area percentage

Set safety area to fit marker ratio or not

Switch on the center cross marker

Select a color for marker

Set the display type of marker

Marker outside color setting

OFF, ON

Top left, Top right, Bottom
left, Bottom right

OFF, LOW, HIGH

OFF, ON

16:9,15:9,14:9,13:9,4:3,2.35:1,2:1,

1.85:1,2.39：1，USER1，USER2

50%~99%

50%~99%

0~1920

0~1080

80%~100%

OFF, ON

OFF, ON

White, Red, Green, Blue, Black, Gray

Type 1，Type 2

OFF, Black, Gray

Turn eye pattern on or off ON,OFF

18

*1 WFM Single Line
Open waveform single-line mode, the monitor shows only one line of audio waveform. Rotate

the Menu/Enter knob to select the number of lines of audio signal to display the waveform.
(The selection range of the number of lines in a waveform depends on the current signal
standard)

Y

940

768

512

256

64

Y

Line:1

940

768

512

256

64

WFM Single Line:OFF WFM Single Line:ON

* 2 Horizontal / Vertical (user 1)

When the value of the scale item is set to "User 1", the user can adjust the X position and Y
position of the marking line according to his/her own needs, and the coordinate value can be
adjusted in the range of 50%~99%;

*3 Horizontal / Vertical (User 2)

When the value of the scale item is set to "User 2", users can adjust the X position and Y position
of the marking line according to their own needs, and the X coordinate value can be adjusted in
the range of 0~1920, and the Y coordinate value can be adjusted in the range of 0~1080.

*4 Eye pattern

Only SDI1 supports eye diagram to monitor the image quality of the current SDI video signal
after transmission over the cable, especially the transmission quality of 12G SDI.

Good Signal

400mV

200mV

-200mV

-400mV

Bad Signal

400mV

200mV

-200mV

-400mV

19

8. De-embed— Setting for video/audio analysis functions

Menu Item

Audio Meter

Lissajous

Surround

Phase

Left Channel

Right Channel

Menu Description

Audio Meter

Audio meter Position

Audio meter Blending

Audio meter marker

Lissajous Pattern

Lissajous position

lissajour Blending

Surround Phase

Surround Position

Surround type

Surround Blending

Select the left channel

*2

output channel
Select the right channel

output channel

Turning audio meters on or off
Adjusting the position of the audio

meter on the screen
Set the transparency of the audio

meter background colour

*1

Setting the audio meter marker line

Turn on or off Lissajous figure

Set the position of the Lissajous
position on the screen
Set the Blending of the Lissajous

background colour
Turn surround Phase on or off
Adjusting the position of the surround

sound display on the screen
Selecting the type of surround sound

Set the transparency of the surround
sound background colour

Channel 1~16

Channel 1~16

Value

ON,OFF
Top Left, Top Right, Bottom Left,

Bottom Right

OFF,LOW,HIGH

ON,OFF

ON,OFF

Top Left, Top Right, Bottom Left,
Bottom Right

Off, Low, High

ON,OFF
Top Left, Top Right, Bottom Left,

Bottom Right

5.1,

OFF,LOW,HIGH

Volume

Time code

H/V Delay

Adjust audio volume

Turn on/

*3

Turn on/off H/V Delay

off Time code

0~100

OFF, ON

OFF, ON

*1. Audio meter marker

Audio table display, display 16 channel audio table
Marking line off: Only the audio table is displayed
Marking line on: Display audio decibels, audio alarm signal and left and right channel options

Marking line: off

1 2

Marking line:on

U

U

U

N

N

L

L

O

O

M

M

M

M

M

M

U

U

U

T

T

E

E

3 4 5 6 7 8 9 10111213141516

L -18dB 01CH R -13dB 02CH

C

C

U

U

U

K

K

T

T

T

T

E

E

E

E

E

E

D

D

U

U

U

U

N

N

N

N

N

L

L

L

L

L

O

O

O

O

O

C

C

C

C

C

K

K

K

K

K

E

E

E

E

E

D

D

D

D

D

-

10

U
N
L

O
C

K
E

D

Audio alarm information

-

20

-

30

-

40

-

50

-

60

Left Channel:1 Green

*2. Left Channel/ Right Channel

Audio meter under SDI showing 16 channel audio meter
Audio meter under HDMI®, menu shows 8 groups of channels

*3. H/V Delay

H/V Delay is not displayed on HDMI® channel.

Right Channel:2 Red

20

9. Auto Calibration

*1

Menu Item

Probe Select

Start Calibration

Measure

*2

*4

*3

Menu Description

Select a probe to use

Select whether to start calibration

Test current color

Value

X-rite I1 Pro OEM, Jeti Specbos 1211

No/Yes

No/Yes

*1.Auto Calibration

The monitor has built-in 3DLUT colour calibration software, which supports Atheros X-rite
I1 Pro OEM and JETI Specobos1211 colour probes directly connected to the monitor via
USB.
When calibration starts, the colour probe will read the standard colour graphics generated
by the monitor and load the results to the monitor via the USB port.
The monitor internally compares the standard colours with the colours read by the probe
to generate a 3DLUT table and complete the automatic colour calibration.
Calibration time: X-rite I1: 15 minutes, JETI Specobos1211: 45 minutes.
Calibration result Delta E <1.0.

*2.Probe Select

This monitor supports the following probes models:

BRAND

X-rite

JETI

I1 Pro OEM（SWIT OEM）

MODEI

Specbos 1211

（SWIT Exclusive Edition only）

X-rite I1

JETI Specbos 1211

*3.Start Calibration

Steps:

1. Put the monitor into a dark room. Switch on the monitor.

2. Connect the calibration instrument (compatible with x-rite and JETI color measuring
instruments) and monitor via USB. Before calibration, ensure that the monitor and the
color calibration instrument are in good condition and the monitor aging time reaches 30
minutes.

.eborp noitarbilac desu yltnerruc eht tceles dna ”tceleS eborP“ eht retnE .3

yalpsid lliw rotinom ehT .noitarbilac trats ot ”sey“ tceles dna ”noitarbilaC tratS“ eht retnE .4
the prompt message and the color position prompt box. Put the sensitive part of the
device in the color position prompt box correctly. Note that when placing the calibration
instrument; do not squeeze the monitor’s LCD screen.

21

Please make sure the monitor is in
dark room,and the sensor probe is
put in the center marker and close
to the screen.

Select MENU to start!

MENU:OK INFO:Quit

Please make sure the monitor is in
dark room,and the sensor probe is
put in the center marker and close
to the screen.

Select MENU to start!

MENU:OK INFO:Quit

Contrast

Brightness

Saturation

USB/Firmware

Power

Phone

Menu/Enter

Source

Volume

User2

User1

Backlight

User4

Info/Quit

User3

5. Select "yes" to begin auto calibration. The color calibration instrument will automatically
measure the color of the screen and correct the color of the screen. During this process, it is
necessary to observe the color calibration progress bar in the color correction prompt box.

6. Press "INFO" to terminate the color correction
process at any time. When the prompt color
calibration progress reaches 100%, the whole
automatic color calibration is completed. After
automatic color correction, press the "INFO"
button to exit the menu and let the monitor enter
the normal display mode.

7. After the automatic color correction, the

arbilaC erofeB“ pu spop neercs yalpsid -

.”noitarbilaC retfA“ dna ”noit

*4. Measure

The monitor has been calibrated in factory. And

may need to be re-calibrated after a period of
time. Before re-calibrated, the measure function

Auto Calibration

Auto Calibration

Progress 23%
Please wait...

Select INFO to Cancel!

INFO：Quit

Before Calibration After Calibration

R

R75

Mg

Mg75

B

B75

Cy

Cy75

G

G75

YI

YI75

W
Delta = 1.0

CIE and Delta E
before calibration

Last Calibration

R

R75

Mg

Mg75

B

B75

Cy

Cy75

G

G75

YI

YI75

W
Delta = 0.9

CIE and Delta E
after calibration

New Measured

can check the current color to compare with the
last time calibrated color, to decide if the monitor
needs to be re-calibrated. Connect with the sensor
probe and place the sensor probe onto the right

arbilaC otuA“ retnE .pets noitarbilac ekil noitisop -

etareneg lliw rotinom ehT .”erusaeM“ ‒ ”noit
several colors and finish measure within 30 sec­onds. And display the result as：

R

R75

Mg

Mg75

B

B75

Cy

Cy75

G

G75

YI

YI75

W
Delta = 1.0

CIE and Delta E
from last calibration

R

R75

Mg

Mg75

B

B75

Cy

Cy75

G

G75

YI

YI75

W
Delta = 0.9

CIE and Delta E
from new measured

22

10. System-User profile saving,firmware update.

Menu Item

Key Lock

Recall Profile

*1

*2

Save Profile

Payload ID

Low Latency Mode

Green mode

Idle Duration

*3

IP

Net Mask

Gateway

Port(1024~65535)

OSD TIME

Key Brightness

Language

Menu Description

Set lock key

Select make user mode current

Save the current state as a user setting

When turned on, Payload ID information conforming to
SMPTE ST 352 standard is automatically adapted

Open or close low latency mode

Set the display mode of green mode

Set how long it will be in the no-signal state and turn
on green mode

Set up the monitor IP address to achieve remote web
control

Set OSD display time

Set the brightness of the key lamp
Select Chinese or English language to display

Value

OFF, Full Lock

Factory,USER1,USER2,USER3,USER4

USER1,USER2,USER3,USER4

OFF, ON

OFF, ON

Black Backlight, Gray Backlight

30 Sec, 1 Hour, 2 Hours, 4 Hours, OFF

192.168.001.200

255.255.255.000

192.168.001.001

08080
5~180

OFF, Low, High

Chinese，English

System Reset

Update

*4

Reset all Settings in the menu system
Set whether to upgrade firmware

No/Yes

No/Yes

*1.Key Lock

Contrast

User1

User2

User3

User4

Info/Quit

Brightness

Backlight

Volume

Saturation

Source

Menu/Enter

USB/Firmware

Phone

Power

ALL

The “Menu/Enter” button can be operated when the button is locked. “Key Locked” will be displayed
on the screen when you press the Locked button or knob.

Key Locked

Contrast

Saturation

Brightness

USB/Firmware

Power

Phone

Menu/Enter

Source

Volume

User2

User1

User3

Backlight

User4

Info/Quit

23

*2 Recall Profile/ Save Profile

User Settings provide 4 menu Settings, that is, users can save the current monitor menu
Settings as one user Settings (USER1~USER4) according to usage habits. Then, when switching
menu Settings, just select the corresponding "USER1~USER4" through the “Recall Profile” item
to display the corresponding menu Settings. Example：By adjusting the parameters of the color
temperature of 2200K, open the necessary auxiliary functions (such as: histogram), set the
function key to the desired menu (such as F1 is set to "Blue Only"), and so on, the monitor
Menu Settings can be "USER Settings" save as "USER" 1, rotating the “Menu/Enter” choose to
load the USER Settings "set to the current" USER 1 "mode, the monitor Menu item value will
show" USER 1 "mode to save Menu.

*3 IP control

Connect the monitor to the LAN through an ETHERNET interface, and the Monitor can
be controlled by web page.

ETHERNET

Pin No

1

2
3
4

5
6
7
8

1
2
3
4
5
6
7
8

Pin Name

MD0P
MD0N
MD1P
MD1N
MD2P
MD2N
MD3P
MD3N

Enter Menu- System ‒ IP/Net Mask/Gateway/Port to set the monitor address. Set the computer
Ethernet IP addresses at the same LAN environment as the Monitor. Launch any of a web
browser on the computer, and enter URL: Monitor IP+ Port (Example: 192.168.1.99.8080). The
web server control page will be displayed.

Monitor IP address

Fig1：IP Address setting Fig2：Web page

Monitor port address

24

●

Used crossed wired cable for computer-monitor directly connection.

●

Use straight-through wired cable for Router connections.

●

Please seek help from your webmaster for any network connections.

Webserver page control interface

After setting up, click this brush
New View the latest Settings

25

*4.Update

System software can update by USB interface, and steps are as follows:

1.Download the latest software package into the U-disk root direction.

2.Open the monitor and plug U-disk into USB into port.

※ Remark

1. Only copy one model and software
version into the U-disk root direction.

2. Never shutdown the power during the
update progress.

11. Multiview setting

.yllacitamotua etadpu lliw rotinom eht ,”etadpU-metsyS-uneM“ pets eht wolloF.3

.rotinom eht toober dna esolc ,nottub ”rewoP“ sserp ,sehsinfi etadpu nehW.4

Menu item

Multiview type *

PIC 1

PIC 2

PIP Windoe position

Menu description Value

2

Selects the Multiview typ

Select channel 1 when set to PBP or PIP.

Select channel 2 when set to PBP or PIP

Select PIC2 position when set to PIP

Quad View、PBP、PIP

SDI 1、SDI 2、SDI 3、SDI 4、HDMI®

SDI 1、SDI 2、SDI 3、SDI 4、HDMI®

Top left, top right, centre,
bottom left, bottom right

Border

Switch on/off the border

On/OFF

Flip(PBP)*

3

Type mode selected at the PBP

Off, type 1, type 2, type 3

*1 Multiview setting

Source selects Multiview before the Multiview Setup menu is adjustable and some menu functions
are disabled;
When Multiview is selected, the quantisation range, colour gamut and gamma of each channel
can be adjusted individually.

*2 Multiview type

4-channel or 2-channel independent 12G/6G/3G/HD-SDI or HDMI® mixed 4-screen or 2-screen
monitoring;
4-screen: If there is no signal input on the 4th screen, HDMI® signal appears on the 4th;

*3 Flip(PBP)

Select the required type,and the screen is in vertical mode to monitor the screen.

26

Appearance and Size

Flight Case Monitor Appearance

FM-215HDR

Contrast

Saturation

Brightness

Source

Volume

User1

Backlight

User2

User3

User4

Info/Quit

Aluminium flight case (unit: mm)

Power

USB/Firmware

Phone

Menu/Enter

ETHERNET

RS485OUT

HDMI IN

2.0

RS485IN

GPI IN

27

Specification

Model No.

Screen Size

Display Area

Resolution

Display Colour

Display Ratio

Maximum Brightness

Contrast Ratio

Colour depth

Signal Processing

Viewing angle H/V

Input/Output Interface

BNC×4

HDMI®×1

FM-215HDR

21.5 inch

476.064×267.786mm

1920×1080

16.7M

16:9

1000 cd/m

1000:1

8bit

18-bit

178°/178°

12G/6G/3G/HD/SD-SDI×1, 3G/HD/SD-SDI×3

HDMI®2.0 input

2

RS-485×1

Input

Output

RS-485×1

USB×1

RJ-45×1

BNC×2

RS-485×1

Analog audio

Other specifications

Operating Voltage AC

DC/Battery

Power consumption

Operating Temperature

Operating humidity

Storage temperature

Storage humidity

TSL3.1/4.0 UMD dynamic source name input

GPI (Tally) input

Gigabit Ethernet port, IP web control access

12G/6G/3G/HD/SD-SDI×1, 3G/HD/SD-SDI×1

TSL3.1/4.0 UMD dynamic source name output

Analog audio 3.5mm and speaker output

100V~240V 50/60Hz

11V～17V

≤60W

0℃～+45℃

10%～90%

-15℃～﹢60℃

10%～90%

flight box size

Net weight (main unit only)

Net weight of flight box

570×260×405mm

7.28KG

6.8KG

28

Supported standards: Signals of the following standards can be displayed on the monitor

Input terminal Signal format shown in the Status Display as

No.

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

Format

1280×720/50P

1280×720/59.94P

1280×720/60P

1920×1080/50I

1920×1080/59.94I

1920×1080/60I

1920×1080/23.98PSF

1920×1080/24PSF

1920×1080/23.98P

1920×1080/24P

1920×1080/25P

1920×1080/29.97P

1920×1080/30P

1920×1080/48P

1920×1080/50P

1920×1080/59.94P

1920×1080/60P

2048×1080/23.98PSF

2048×1080/24PSF

2048×1080/25PSF

2048×1080/29.97PSF

2048×1080/30PSF

2048×1080/23.98P

2048×1080/24P

2048×1080/25P

2048×1080/29.97P

2048×1080/30P

2048×1080/47.94P

2048×1080/48P

2048×1080/50P

2048×1080/59.94P

2048×1080/60P

3840×2160/23.98P

3840×2160/24P

3840×2160/25P

3840×2160/29.97P

3840×2160/30P

3840×2160/47.94P

3840×2160/48P

SDI1

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

SDI 2/3/4

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

Quadlink

SDI

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

√

√

√

√

√

√

√

HDMI®

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

√

SDI1 out

1280*720P50

1280*720P59.94

1280*720P60

1920*1080I50

1920*1080I59.94

1920*1080I60

1920*1080PSF23.98

1920*1080PSF24

1920*1080P23.98

1920*1080P24

1920*1080P25

1920*1080P29.97

1920*1080P30

1920*1080P48

1920*1080P50

1920*1080P59.94

1920*1080P60

2048*1080PSF23.98

2048*1080PSF24

2048*1080PSF25

2048*1080PSF29.97

2048*1080PSF30

2048*1080P23.98

2048*1080P24

2048*1080P25

2048*1080P29.97

2048*1080P30

2048*1080P47.94

2048*1080P48

2048*1080P50

2048*1080P59.94

2048*1080P60

3840*2160P23.98

3840*2160P24

3840*2160p25

3840*2160P29.97

3840*2160P30

3840*2160P47.94

3840*2160P48

SDI2 out

1280*720P50

1280*720P59.94

1280*720P60

1920*1080I50

1920*1080I59.94

1920*1080I60

1920*1080PSF23.98

1920*1080PSF24

1920*1080P23.98

1920*1080P24

1920*1080P25

1920*1080P29.97

1920*1080P30

1920*1080P48

1920*1080P50

1920*1080P59.94

1920*1080P60

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

HDMI®

1280*720P50

1280*720P60

1280*720P60

1920*1080I50

1920*1080I60

1920*1080I60

1920*1080PSF24

1920*1080PSF24

1920*1080P24

1920*1080P24

1920*1080P25

1920*1080P30

1920*1080P30

1920*1080P48

1920*1080P50

1920*1080P60

1920*1080P60

2048*1080PSF24

2048*1080PSF24

2048*1080PSF25

2048*1080PSF30

2048*1080PSF30

2048*1080P24

2048*1080P24

2048*1080P25

2048*1080P30

2048*1080P30

2048*1080P50

2048*1080P48

2048*1080P50

2048*1080P60

2048*1080P60

3840*2160P24

3840*2160P24

3840*2160p25

3840*2160P30

3840*2160P30

3840*2160P50

3840*2160P48

29

Input terminal Signal format shown in the Status Display as

No.

40

41

42

43

44

45

46

47

48

49

50

51

52

Format

3840×2160/50P

3840×2160/59.94P

3840×2160/60P

4096×2160/23.98P

4096×2160/24P

4096×2160/25P

4096×2160/29.97P

4096×2160/30P

4096×2160/47.94P

4096×2160/48P

4096×2160/50P

4096×2160/59.94P

4096×2160/60P

SDI1

√

√

√

√

√

√

√

√

√

√

√

√

√

SDI2/3/4

—

—

—

—

—

—

—

—

—

—

—

—

—

Quadlink

SDI

√

√

√

√

√

√

√

√

√

√

√

√

√

HDMI®

√

√

√

√

√

√

√

√

√

√

√

√

√

SDI1 out

3840*2160P50

3840*2160P59.94

3840*2160P60

4096*2160P23.98

4096*2160P24

4096*2160P25

4096*2160P29.97

4096*2160P30

4096*2160P47.94

4096*2160P48

4096*2160P50

4096*2160P59.94

4096*2160P60

SDI2 out

—

—

—

—

—

—

—

—

—

—

—

—

—

HDMI®

3840*2160P50

3840*2160P60

3840*2160P60

4096*2160P24

4096*2160P24

4096*2160P25

4096*2160P30

4096*2160P30

4096*2160P48

4096*2160P48

4096*2160P50

4096*2160P60

4096*2160P60

3G supports level A/levelB; Support RGB444

√: The format is supported

—: The format is not supported

30

Common Problems and Solutions

symptom

No display

Possible causes Solution

The power is not turned on

Unstable power voltage

BNC or HDMI® cable loose
contact or not correctly
connected

The attached battery is
no power

Using DIY power supply but
the polarity is reversed

Bad contact of BNC
or HDMI® cable

Video signal has Interference

Please check if the power is connected, and then press

“POWER” button to turn on the monitor

Reconnect to power supply

Check and correctly connect the BNC or HDMI® cable

Change battery

Refer to the provided power supply,
reconnect the power.

Change the Video cable

Remove the interference source(s)

Image or
color abnormal

No audio
output

Improper adjustment of the
color parameters

Distortion of the image

Set to Blue only

Turn on the “Focus Assist”
function

Turn on the “False Color”
function

Set mute state

Bad contact of signal cable

Adjust the “Recall profile” to “Default”
under “System” submenu

Reset the Aspect ratio

Turn off the “pure color “ setting

Turn off the “Focus Assist” function

Turn off the “False Color” function

Cancel mute state or spin ” MENU/ENTER ”
to adjust volume

Change signal cable

Wrong connection or bad
contact of Audio cable

Connect to the correct input socket

31

SWIT Electronics Co., Ltd.

Add: 10 Hengtong Road, Xin'gang, Nanjing Economic and
Technological Development Zone, Nanjing 210038, P.R.China
Tel: [phone] Email: [e-mail]