SWIT BM-215NDI, BM-245NDI Users Guide

SWIT ELECTRONICS CO., LTD.

BM-NDI

Model：BM-215NDI、245NDI

R

4K Studio LCD Monitor

User Manual

Thank you for choosing SWIT products, please read this user

manual seriously before using.

Ver：A

01

Statement

Any internal technology (including hardware equipment, software design and product trademark)
of the product shall be protected by law, and any infringement of intellectual property rights of the
product shall be investigated for legal liability。

All the brand and trademark in this product are protected by law,all other company’s brand and
trademark in this product are protected by their owner’s law.

In order to better service majority users,SWIT products will keep improving and developing,SWIT
keep the right to revise and improve this user manual without previous notice.

The warranty period of this product are two years,the following condition are not covered by the
warranty:
⑴ The appearance and the LCD panel are damaged by man-made out force；
⑵ The amount of defective pixels are under three；
⑶ The product is damaged by using incompatible power adaptor；
⑷ The product is damaged by failure to use, maintain or storage according to the user manual.；
⑸ The product is disassembled by user in the process of using；
⑹Other faults or damages not caused by design ,technology,manufacture and quality.

＊Any sales person have no right to provide extra warranty beyond these terms.

Please feel free to contact with us by phone,fax or email when you have any question or need any
help in the process of using.

⸻ This user manual applies to all BM-NDI model monitor,all the illustration take BM-215-NDI

for example,any difference of specification or appearance,this manual will be attached text
explanation;

⸻ The function with mark ”#” in this user manual have not been realized yet.

SWIT Electronics Co., Ltd.

Address: 10 Hengtong Road, Nanjing Economic and Technological Development Zone,
Nanjing 210038, P.R.China
Phone: [phone]
Fax: [phone]
Email: [e-mail]
http://www.swit.cc

02

Attention

Warning

1. Do not put the monitor in rainy or wet environment to avoid the dangerous of fire or electric shock；

2. Do not put the monitor close to any device with high-intensity magnetic.

Warning of power connection

1. Please using original power adaptor to avoid damage；

2. When using other DC power ,make sure the range of voltage,output power and polarity of it meet

requirements；

3. Please cut off the power including AC power cable or battery under below conditions:

（A）、If the monitor will not be used for a long time.

（B）、If the power cable or power socket is damaged.。

（C）、If the housing of the monitor is broken by out-force or falling.

Warning of using

1. Do not touch the surface of screen directly to avoid damage,also the fingerprint on the screen

will be hard to clean.

2. Do not put pressure on the LCD screen because LCD screen is fragile；

3. Do not put the monitor on anywhere unstable to avoid falling.

Maintenance and cleaning

1. Use soft dry cloth and LCD screen clean liquid to clean the dust and stain on the screen.

2. Do not put pressure on LCD screen when doing cleaning.

3. Do not clean the LCD screen by water or other chemical liquid to avoid damage.

03

Table of contents

Statement
Attention
Table of contents
Packing list
Product feature
Instruction
Front panel view
Back side view
OSD
Status
Operation
The menu content
Dimension
Specification
Troubleshoot

Packing list

2
3
4
4
4
5
5
7
8
9
10
10
18
19
22

No.

1

2

3

4

Standard accessories

Monitor

Battery plate（V-mount or Gold-mount）

Monitor stand

Power cable

Quantities

X

1

X

1

X

2

X

1

Overview

The resolution of BM-NDI series LCD monitor is up to 1920*1080, H178°/ V178° super wide angle of
view，support 2* 3G/HD/SD-SDI input 、1* HDMI 2.0 input and 1* NDI input，1* 3G/HD/SD-SDI loop
out、1* NDI to SDI loop out，1* 3.5mm jack input and speaker.

Features:

1920×1080 HD resolution；
Support NDI signal input、multi signal source input；
Support 16 channel embedded audio bar,any of two channel can be chosen to output；
Waveform Y/Cb/Cr/R/G/B/RGB, support single line waveform；
Support vector scope、R/G/B/Y histogram、red/blue focus assist；
Support 3DLUT（17x17x17）Auto self-calibration；
Support TSL UMD and text TALLY（TSL 3.1/4.0）；
Safety Marker：4:3/13:9/14:9/15:9/16:9/1.85:1/2.35:1/2.39:1/2:1/User 1/User 2；
Support USB firmware update and LOG file uploading（The format of USB driver should be FAT 32）；
Support Green mode.

04

Instruction

·Front panel view

(1)

(2)

(3)

(11)

(4)

(5)(6)

(7) (8) (9) (10)

（1） Tally light：Can be set to red, green and yellow；
（2） Speaker：Can play embedded audio of HDMI、SDI and NDI.（Speaker will not work when

earphone is connecting）；
（3） Desktop stand feet ;
（4） User1~User4：In order to quickly enter in the mode which was preset already .Hold the

shortcut button to save current user setting.Specific please see “The menu content-Ⅷ.

System” ；
（5） INFO：Press ”INFO” to remove or recover all current function in display like status information

and A/V analyzed pattern；Press “INFO” to exit menu when the menu is on；
（6） F1~F5 Function key：User can set these function key to different function according to their

requirement；

05

(7)

Brightness：Brightness control,Range:-100~100，
Default value:0

Brightness Contrast Saturation

value: 0

Saturation：Saturation control,Range:-100~100，Default
value:0

Contrast：Contrast control,Range:-100~100，Default

Backlight Volume Source

Backlight：Backlight control,Range:0~100，Default
value:16

Volume：Volume control,Range:0~100，Default value:36
Source：Input signal source selection

Press “Brightness”、”Contrast”、”Saturation、Backlight”、”Volume” on the front panel
to choose corresponding functions,turn “MENU” knob left and right to control the
corresponding value。If no operation is performed within 5 seconds,the selection will
automatically cancelled,the button light will off;long press to recover to default
value；long press the “VOLUME” button to enter in mute mode.

“NDI Source” and “NDI setting” in the menu is to choose the input source under NDI

channel,here are the details:

1. NDI Source：Detect and show all NDI device and all NDI signal name of NDI device in
the same network,turn “MENU & ENTER” to change different signal source.

2. NDI Setting：Set the IP address of secondary network device of monitor to be able to
detect secondary device and the signal source.

（8） Menu/Enter：When menu is off,press the button directly to open the Main Menu；rotate

“MENU” to choose different setting selection or adjust the value；press the knob to

confirm the setting；
（9） LUT/Firmware：Firmware update or LUT file upload；
（10）PHONE：3.5mm jack input，monitor embedded SDI and HDMI audio signal；
（11）Power：power switch.

06

·Back side view

(1)
(2)

(3)
(4)

(5)
(6)

(7)

(8)

(12)

(9)

(10)

(11)

（1）SDI IN1/2： 3G-SDI
（2）NDI-SDI loop out：3G-SDI
（3）SDI loop out：3G-SDI
（4）NDI IN：12G /3G-SDI
（5）HDMI 2.0 IN：The DHCP protected content is not displayed
（6）Reset: Formatting button

Instruction（Do not do this without SWIT permission）：

1. Switch off monitor；

2. Touch and keep pressing the small button with suitable tool
（Do not release it when switch on monitor）；

3. Switch on monitor with “POWER” button，Tally light will show red light
（release the reset button after tally light shows red light）；

4. Wait for 5~10s，Tally light shows green；

5. Reboot monitor to finish resetting.
（7） RS485 #：TSL UMD control port
（8） GPI #：GPI control port
（9） Fan
（10）DC IN：12V～17V
（11）AC IN：100V～240V
（12）Battery plate：Support V-mount battery or Gold-mount battery

07

·OSD

(1)

(7) (8)

TC 00:15:13:07

CAMERA

(2)

(3)

in phase

L

R

(4)

(5)

(6)

⑴ Time code（SDI）

Display the information of time code which is embedded in SDI signal（LTC，VITC1&2），moni­tor will show “TC:UNLOCKED” if no time code information is detected.User can set shortcut
key（F1~F5） or GPI pin to “time code” function，in order to quickly switch on/off this function.

⑵ On screen TALLY

The tally signal is controlled by GPI.

⑶ Source ID/UMD

Display/UMD（TSL3.1/4.0），user can set in the UMD menu.

⑷ Lissajous pattern

Lissajous pattern will show audio signal，user can set shortcut key（F1~F5） or GPI pin to

“Lissajous pattern” function，in order to quickly switch on/off this function.

⑸ Waveform

User can switch on/off “Waveform” function or choose different type of waveform by setting
shortcut key(F1~F5) or GPI pin to “Waveform” function on the front panel.The parameters
such as on-screen-position,transparency and color of “waveform” can be set in MENU.

⑹ Vector scope

User can switch on/off “Vector scope” function by setting shortcut key(F1~F5) or GPI pin to

“Vector scope” on the front panel.The parameters such as on-screen-position,transparency

and color of “Vector scope” can be set in MENU.

⑺ Audio meter

In order to monitor audio signal，User can switch on/off “Audio meter” function by setting
shortcut key(F1~F5) or GPI pin to “Audio meter” function on the front panel. The parameters
such as on-screen-position, transparency and numbers of audio channel of “Audio meter” can

08

be set in MENU.

⑻ Histogram

User can switch on/off “Histogram” function by setting shortcut key(F1~F5) or GPI pin to

“Histogram” function on the front panel.

Status

Main Menu

Exit&Status >
Input >
Picture >
Color Management >
Scanning >
Control >
Assist >
De-embed >
Auto Calibration >
NDI Source >
NDI Settings >
Multiview Setting >

Press “Menu/Enter”，the menu will show in the top left corner of screen，“Exit & status” will
show current working status of monitor.

⑴ Format

Show current input signal format；Will show “NO SIGNAL” when there is no recognizable
input signal”.Will show the format of current SDI source when the input source is SDI.

⑵ Channel

Show current chosen input source.

⑶ Color temp

Show current color temperature.

⑷ Function Key F1~F5

Show the function of Key F1~F5.

(5) Loaded Profile

Show current user mode.

(6) Network

Show the connection status of Internet.

（7）Version

Show version of current firmware .

（8）Host name

Show the model of this monitor.

Status

Format
Channel
Color Temp
F1
F2
F3
F4
F5
Loaded Profile
Network
Version XX
Host Name XX

XX
XX
XX
XXX
XXX
XXX
XXX
XXX
XX
XX

(1)
(2)

(3)
(4)

(5)
(6)
(7)

(8)

09

Operation

Steps

1、Press “Menu/Enter” knob，the menu will show on top left corner of screen.
2、Turn “Menu/Enter” left and right to choose different sub-menu,the chosen one will show yellow
backlight,press“Menu/Enter” knob to set the corresponding parameter.
3、Turn “Menu/Enter” knob left and right to set corresponding parameter，press “Menu/Enter”knob，
the chosen one will show yellow backlight.
4、Turn “Menu/Enter” knob left and right to set corresponding parameter,press “Menu/Enter” knob
to save the setting after finish adjustment.
5、Turn “Menu/Enter” knob to choose “EXIT”，press “Menu/Enter” knob，exit the sub menu,choose
“EXIT & STATUS” in the main menu,press “Menu/Enter” knob to exit main menu.

Attention

＊ The options which shown grey can not be set.
＊ The menu will save and exit automatically when no operation is performed within a period of time.

The menu content

“The menu content” will introduce the specific contents of setting in menu and sub-menu,the menu

option which is noted with “ * ” will be explained in detail under the list.

Ⅰ、Input—Set the color of input video

Menu option

Input range *1
YUV Color Matrix
Red Gain
Green Gain
Blue Gain
Red Bias
Green Bias
Blue Bias
Reset

*1 Input range

Set the input range to compatible with input video signal,the default input range is 64-940 which
is compatible with broadcast application program.

Instruction

Set the input range of video
Choose YUV Color Matrix
Adjust the value of Red Gain
Adjust the value of Green Gain
Adjust the value of Blue Gain
Adjust the value of Red Bias
Adjust the value of Green Bias
Adjust the value of Blue Bias
Reset the value of Gain and Bias

The range of value

0-1023,4-1019,64-940，64-1023
Auto，BT.601，BT.709，BT.2020

-100 ~ +100

-100 ~ +100

-100 ~ +100

-100 ~ +100

-100 ~ +100

-100 ~ +100
/

Ⅱ、Picture *1—Set the display of input video

Menu option

Contrast
Brightness
Saturation
Sharpness
Backlight

Instruction

Adjust the contrast of video
Adjust the brightness of video
Adjust the saturation of video
Adjust the sharpness of video
Adjust the backlight of video

The range of value

-100 ~ +100

-100 ~ +100

-100 ~ +100
0 ~ +100
0 ~ +100

10

*1 Picture

The value of “Contrast”,“Brightness”,“Saturation”，“Sharpness” and “Backlight” can be quickly
adjusted by the shortcut key on the front panel.

Ⅲ、Color management—Set the color of input video

Menu option

Color Gamut *1

Gamma

These
option
will only
show under
the value
of specific
Color Gamut
and Gamma

Color temp

Color temp(USER)

HLG System
Gamma *2

D-Log to 709
*3

D-Log to PQ

D-Log to HLG

Instruction

Set the Color Gamut

Set the value of Gamma

Set HLG System Gamma

Set the camera LUT when Color
Gamut is Rec 709.

Set the camera LUT when Color
Gamut is Rec.2020，Gamma is PQ1000

Set the camera LUT when Color
Gamut is Rec.2020，Gamma is

HLG1000

Set the value of color temperature

Set the value of color temperature
(USER)

The range of value

LCD Panel，DCI-P3，Rec.709，Rec.2020

1.0，1.8，2.2，2.4，2.6，PQ1000，HLG1000，S-Log3

1.0,1.1,1.2（default）,1.3,1.4,1.5

OFF，J-Log1，Log-C，S-Log2，C-Log，V-Log，
RedLogFilm，S-Log3，User-Log

OFF,ARRI_LogC_PQ,Canon_CLog2Cin_PQ
Canon_CLog3Cin_PQ，Panasonic_VLog_PQ,
RED_L3G10_PQ，Sony_SLog3_Cin_PQ,

Sony_SLog3_SG3_PQ
OFF,ARRI_LogC_HLG,Canon_CLog2Cin_HLG

Canon_CLog3Cin_HLG，Panasonic_VLog_HLG,
RED_L3G10_HLG，Sony_SLog3_Cin_HLG,
Sony_SLog3_SG3_HLG

2000K~10000K, D55,D65,D75,D93,USER1,USER2

2000K~10000K，D55，D65，D75，D93

Red Gain

Green Gain

Blue Gain

Red Bias

Green Bias

Blue Bias

Import*4

Adjust the value of Red Gain(USER)

Adjust the value of Green Gain(USER)

Adjust the value of Blue Gain(USER)

Adjust the value of Red Bias(USER)

Adjust the value of Green Bias(USER)

Adjust the value of Blue Bias(USER)

Choose the cube file which need to
be imported

-100 ~ +100

-100 ~ +100

-100 ~ +100

-100 ~ +100

-100 ~ +100

-100 ~ +100

None，3DLut.cube

*1 Color Gamut

Set the Color Gamut to match with input video.

*2 HLG System Gamma

Only adjustable when Gamma is HLG1000

*3 D-Log to 709：Only adjustable when Color Gamut is Rec.709 and Gamma is between 1.0，

1.8，2.2，2.4，2.6
*4 Import

Put the cube file in the root of USB driver，connect USB driver with the monitor via USB
interface on the front panel,choose and import corresponding file in the menu.

11

Ⅳ、Control

Menu option

F1*1
F2
F3

Instruction

Set the function of shortcut key

Selection

Time Code, Color Temp,Waveform,
Waveform type,Single line waveform,
Marker,Blue only,Audio Bar,Zebra,Vector,
Histogram,Odd/Even Frame,Lissajous

F4

pattern,Focus assist,False color ,H/V delay

F5

*1F1~F5
Now only support “Waveform,Vector,Audio Bar,Blue only,Marker”.

Ⅴ、Assist

Menu option

False color
Blue only

Focus assist

Zebra

Waveform
Setting

Vector
Setting

Waveform
WFM Type
WFM Position

WFM Blending

WFM Color
WFM Single Line*1
WFM Line Count
Vector
CIE
Vector Position

Vector Blending

Instruction

Switch on/off false color function
Switch on/off Blue only function

Switch on/off Focus assist function and
choose the color of it.

Switch on/off Zebra function
Switch on/off waveform function
Set the type of Waveform

Set the display position of Waveform pattern
Set the transparency of the background of

Waveform pattern

Set the color of the Waveform
Switch on/off Single line Waveform function
Adjust to show Waveform of specific lines
Switch on/off Vector function
Swtich on/off color gamut pattern
Set the display position of Vector pattern.

Set the transparency of the background of
Vector pattern .

Selection

OFF,ON
OFF,ON

OFF,Blue,Red

OFF,ON
OFF,ON
Y, Cb, Cr, R,G,B, RGB
Bottom left,Bottom right,Top left,Top right

OFF,LOW,HIGH

White,Green,Color
OFF,ON
1-2160
OFF，ON
OFF,ON
Bottom left,Bottom right,Top left,Top right

OFF,LOW,HIGH

Histogram
setting

Marker
setting

Vector color
Histogram

Histogram Blending

Marker

Marker Select

Horizontal*2
Vertical
Safety area
Fit Marker
Center Marker
Marker Color
Marker Type

Marker Outside

Set the color of Vector pattern
Switch on/off Histogram pattern

Set the transparency of the background of
Histogram pattern .

Switch on/off Marker function

Set the ratio of Marker

Set the X value of Marker function
Set the Y value of Marker function
Set the ratio of Safety area
Switch on/off Fit Marker function
Switch on/off Center Marker function
Set the color of Marker
Set the type of Marker

Switch on/off Marker Outside function and
change the color.

White,Green,Color
OFF,ON

OFF,LOW,HIGH

OFF,ON
16:9，15:9，14:9，13:9，4:3，2.39:1，2.35:1，2:1，

1.85:1，USER 1，USER 2

50%~99%（0~1920）
50%~99%（0~1080）
80%~99%
OFF,ON
OFF,ON
White,Red,Green,Blue,Black,Grey
Type 1，Type 2

OFF,Black,Grey

12

*1 WFM Single line

Switch on “WFM Single line” function,Monitor only show one line waveform of video.Turn

“Menu/Enter” knob left and right to choose the number of waveform lines.。（The selected

range of waveform lines depends on the current signal format.）

Y

940

768

512

256

64

Y

940

768

512

256

64

WFM Single Line：OFF WFM Single Line:ON

*2 Horizontal/Vertical

When the “Marker Select” is “USER 1” or “USER 2”，User can adjust X value and Y value of Marker
according to their requirement，the value is adjustable between 50%~99%（0~1920 and 0~1080）.

Ⅵ、De-embed

Menu option

Lissajous

Instruction

Switch on/off Lissajous pattern

Selection

OFF,ON

Lissajous Position

Set the display position of
Lissajous Pattern

Audio Bar

Bar Position

Switch on/off Audio Bar function

Set the display position of Audio Bar

Set the transparency of the background

Bar blending

Bar type*1

Left Channel

Right Channel

Volume

H/V delay*2

of Audio Bar .

Set the type of Audio Bar

Select left input audio channel

Select Right input audio channel

Adjust the volume of audio signal

Switch on/off H/V delay function

*1 Bar type:Audio bar show 16 channel

Bottom left,Bottom right,Top left,
Top right

OFF,ON
Bottom left,Bottom right,Top left,

Top right

OFF,LOW,HIGH

Type 1，Type 2

Channel 1~16

Channel 1~16

0~100

ON,OFF

Type 1:Audio bar only
Type 2:Show db value of audio signal，audio warning signal and right/left channel information

13

Type 1 Type 2

U

U

N

N

L

L

O

O

M

M

M

M
U

T
E

3 4 5 6 7 8 9 10111213141516

1 2

L -32DB 01CH

C

C

U

U

U

K

K

T

T

T

E

E

E

E

E

D

D

U

U

N

N

L

L

O

O

C

C

K

K

E

E

D

D

R -13DB 02CH

U

U

U

U

N

N

N

N

L

L

L

L

O

O

O

O

C

C

C

C

K

K

K

K

E

E

E

E

D

D

D

D

-09

-20

Audio alarm information

-48

Left Channel:1 Green

Right Channel:2 Red

*2. H/V Delay

H/V Delay is not displayed on HDMI channel.

Ⅶ、Auto Calibration*1

Menu option

Probe Select*2

Start Calibration*3

Measurement*4

*1 Auto Calibration

Monitor internally installed 3DLUT Calibrate software，support to directly connect with
below calibrator via USB interface on the front panel.
When start to calibrate,calibrate probe will read the standard color created by monitor
and upload the result to monitor via USB interface.
Monitor will compare the color which created by calibrate probe with standard color
and create a 3D LUT file and finish calibrating automatically.

*2 Probe Select

This monitor support below kinds of calibrate probe：

Instruction

Select the calibrator

Start to calibrate or not

Test current color

Selection

X-rite l1 Pro OEM，Jeti Specbos 1211

NO/YES

NO/YES

BRAND

X-rite

JETI

MODE

I1 Pro OEM

Specbos 1211

*3 Start Calibration
Steps:

1、 Switch on monitor.
2、 Connect Calibrator with monitor via USB interface on the front panel（Compatible with X-rite
and JETI）.Make sure monitor and calibrator is in good condition and the aging time of
monitor is over 30 minutes.
3、 Select “MENU”-“AUTO CALIBRATION”-“Probe Select” to select current calibrate probe.
4、 Select “Start Calibration”-“YES” to start calibrating.Monitor will show info box and calibrate
position hint box，make sure the lens of calibrator is forward to the calibrate position hint
box.Do not push the LCD screen when setting the calibrator.

14

Auto Calibration
Please make sure the monitor is in
dark room,and the sensor probe is
put in the center marker and close
to the screen.

Select MENU to start!

MENU:OK INFO:Quit

Auto Calibration
Please make sure the monitor is in
dark room,and the sensor probe is
put in the center marker and close
to the screen.

Select MENU to start!

MENU:OK INFO:Quit

Auto Calibration
Progress 23%
Please wait...

Select INFO to Cancel!

INFO：Quit

5、Select “OK” to do auto-calibratio.Calibrator will measure the color of screen and calibrate the
screen automatically，please pay attention to the progress bar.

6、Press “INFO” to stop calibration.When the progress bar reach to 100%，auto calibration finished.
Press “INFO”to exit menu after auto-calibration,monitor will recover to normal.
7、The screen will show the Delta value before and after calibration,shown as below:

Before Calibration After Calibration

R

R75

Mg

Mg75

B

B75

Cy

Cy75

G

G75

YI

YI75

W
Delta = 2.3

CIE and Delta E
before calibration

R

R75

Mg

Mg75

B

B75

Cy

Cy75

G

G75

YI

YI75

W
Delta = 0.9

CIE and Delta E
after calibration

*4 Measurement

Monitor have calibrated in factory already but also need to re-calibrate after a period of time
using.Before re-calibrating,“Measurement” function will show Delta value of last time calibration,
user can decide to calibrate or not from comparing the Delta value.

Connect calibrate probe with monitor and
put it on the right position，Select “Auto

Last Calibration

New Measured

Calibration”-“Measurement”，Monitor will
create part of color and finish testing within
30 seconds.Testing result shown as below：

R

R75

Mg

Mg75

B

B75

Cy

Cy75

G

G75

YI

YI75

W

Delta = 0.9

CIE and Delta E
result of last calibration

R

R75

Mg

Mg75

B

B75

Cy

Cy75

G

G75

YI

YI75

W
Delta = 2.3

CIE and Delta E
result of new measured

15

Ⅷ、System

Menu option

Key Lock *1

Recall Profile *2

Save Profile

Green Mode

Idle Duration

DHCP*3

IP *4

Net mask

Gateway

OSD TIME

Language

System Reset

Update *5

Instruction

Set key lock function

Select current Mode

Save current setting to one of USER setting

Set the display mode of Green Mode

Set the stand-by time before switch on Green Mode

Switch on/off DHCP Mode

Show current network information of monitor

Set the lasting time of OSD

Select the operation language of monitor

Reset all setting in the menu

To do update for monitor

Selection

OFF,Lock All,Lock Rotary Knobs,
Lock Key Buttons

Factory，USER1~USER4

USER1~USER4

Black Bcklight,Grey Backlight

30s，1hour，2hour，4hour，OFF

ON,OFF

192.168.001.200

255.255.255.000

192.168.001.001

5~180s

中文(Chinese)，English

NO/YES

NO/YES

*1.Key Lock

All

When “Key Lock” function is “ON”，part of menu will be hidden,only “Menu” button is available，
other button will be locked.
Screen will show “Key Locked” when the locking button is pressed,shown as below:

Key Locked

16

*2 Recall Profile/Save Profile

Monitor supply 4 User setting,User can save current setting according to demand and habit to
(USER1~USER4).After that,user only need to select “USER1~USER4” to show corresponding menu
setting.
For example：Adjust “Color Temp” to 2200K，switch on assist function such as “Histogram”，set
function key such as F1 to “Only Blue” ，now save all these setting to “USER 1”，turn “Menu/Enter” to
select “Recall Profile”-“USER 1”，monitor will change all setting to the setting which saved in “USER 1”.

*3 DHCP

The IP address will be assigned by router or switch automatically when “DHCP” function is “ON”；
User can set IP/Net mask/Gateway manually to match their own Network segment when “DHCP”
function is “OFF” in order to detect the NDI signal source in system.

*4 IP

Connect monitor to the LAN with NDI IN/ETHERNET port in order to control monitor by website.

NDI IN

ETHERNET

Pin No

1
2
3
4
5
6
7
8

Pin Name

TX+
TX­RX+

RX-

Website loading：Open browser and enter the IP address to load the monitor web page.

◎ Make sure the network cable which used to connect monitor with computer directly is

cross line cable.
◎ Make sure the network cable which used to connect monitor with router is
straight-through cable.
◎ If you have any problem with your network connection,please ask your network administrator
for help.

*5 Update

Firmware can be updated via USB port，update steps as below：

1、Update the latest firmware to the root of USB driver

2、Switch on monitor,connect your USB driver with monitor

3、Select “MENU”-“SYSTEM”-“Update”,the monitor will update automatically.

4、Press “Power” button to switch off and reboot monitor after successfully updating.

17

UPDATE

Do you want to update now?
Select MENU to start !

MENU:OK INFO：Quit

Ⅸ、Multiview Setting

※Caution
1、Make sure only one firmware is copied to the root of USB
driver one time.
2、Do not cut off the power when doing update.

Menu option

Multiview Type*1

PIC 1 *2

PIC 2

PIP Window Position

Border

Instruction

Set the type of Multiview function

Set the signal channel of Multiview function

Set the Position of PIP on screen

Set the border of PIP function

Selection

PBP,PIP

SDI1，SDI2, HDMI，NDI

Bottom left,Bottom right,Top left,Top right, Center

ON，OFF

*1 Multiview Type

“Multiview Setting” is available when signal channel is Multiview,otherwise “Multiview setting” will
show grey and unavailable；
The “Input range”,“Color gamut”,“Gamma”,“UMD” and “Payload ID” of each video can be set sepa
rately when signal channel is “Multiview”；
Part of menu function will be disabled when signal channel is Multiview.

*2 PIC 1、PIC 2

When signal channel is “Multiview”，“PIC 1” and “PIC 2” can select to display any signal channel.

Overall Dimension

Dimension（mm）

BM-215-NDI

18

580.9

BM-245-NDI

Specification

LCD Performance

Model

BM-215-NDI

392.3

423

BM-245-NDI

Size

Display area

Resolution

Display color

Display ratio

Brightness

Contrast

Viewing angle

Input /Output

Input

Output

21.5

495.6×292.2mm

1920*1080

16.7M

16:9

400

3000:1

H/ V：178°/ 178°

BNC×2

HDMI×1

RS-485×2

GPI×1

USB×1

ETHERNRT/NDI

BNC×1

BNC to NDI×1

RS-485×1

23.8

543.0×316.72mm

1920*1080

16.7M

16:9

400

3000:1

H/ V：178°/ 178°

3G/HD/SD-SDI×2

HDMI Input

UMD×1

12G/6G/3G/HD/SD

3G/HD/SD-SDI×1

3G/HD/SD-NDI×1

UMD×1

Other specification

Working
voltage

Power consumption

Working Temperature

Working Humidity

Storage Temp

Storage Humidity

Overall Dimension

Net weight

（Only monitor body）

AC：100V～240V

DC/Battery：12V～17V

45W

0℃～+50℃

10%～90%

﹣15℃～﹢60℃

10%～90%

530.6×364.3×74.2mm

5.90KG

580.9×392.3×74.2mm

8.87KG

19

Supported format：Below signal format can be displayed on the monitor

Input terminal Signal format shown in the Status Display as

No.

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

720×480/60I

720×480/60P

720×576/50I

720×576/50P

1280×720/23.98P

1280×720/24P

1280×720/25P

1280×720/29.97P

1280×720/30P

1280×720/50P

1280×720/59.94P

1280×720/60P

1920×1080/50I

1920×1080/59.94I

1920×1080/60I

1920×1080/23.98PSF

1920×1080/24PSF

1920×1080/23.98P

1920×1080/24P

1920×1080/25P

1920×1080/29.97P

1920×1080/30P

1920×1080/48P

1920×1080/50P

1920×1080/59.94P

1920×1080/60P

2048×1080/23.98PSF

2048×1080/24PSF

2048×1080/25PSF

2048×1080/29.97PSF

2048×1080/30PSF

2048×1080/23.98P

2048×1080/24P

2048×1080/25P

2048×1080/29.97P

2048×1080/30P

2048×1080/47.94P

2048×1080/48P

2048×1080/50P

Format

SDI1/2

√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√

NDI

—

—

—

—

—

—

—

—

—

√
√
√
√
√
√

—

—

√
√
√
√
√

—

√
√
√

—

—

—

—

—

—

—

—

—

—

—

—

—

HDMI

—

√

—

√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√

SDI

720*480I60

720×480/60P

720×576/50I

720×576/50P

1280×720/23.98P

1280×720/24P

1280×720/25P

1280×720/29.97P

1280×720/30P

1280*720P50

1280*720P59.94

1280*720P60

1920*1080I50

1920*1080I59.94

1920*1080I59.94

1920×1080/23.98PSF

1920×1080/24PSF

1920×1080/23.98P

1920*1080P23.98

1920*1080P25

1920*1080P29.97

1920*1080P29.97

1920×1080/48P

1920*1080P50

1920*1080P59.94

1920*1080P59.94

2048×1080/23.98PSF

2048×1080/24PSF

2048×1080/25PSF

2048×1080/29.97PSF

2048×1080/30PSF

2048×1080/23.98P

2048×1080/24P

2048×1080/25P

2048×1080/29.97P

2048×1080/30P

2048×1080/47.94P

2048×1080/48P

2048×1080/50P

HDMI

—

720*480P60

—

720*576I50

1280*720P24

1280*720P24

1280*720P25

1280*720P30

1280*720P30

1280*720P50

1280*720P60

1280*720P60

1920*1080I50

1920*1080I60

1920*1080I60

1920*1080PSF24

1920*1080PSF24

1920*1080P24

1920*1080P24

1920*1080P25

1920*1080P30

1920*1080P30

1920*1080P48

1920*1080P50

1920*1080P60

1920*1080P60

2048*1080PSF24

2048*1080PSF24

2048*1080PSF25

2048*1080PSF30

2048*1080PSF30

2048*1080P24

2048*1080P24

2048*1080P25

2048*1080P30

2048*1080P30

2048*1080P50

2048*1080P48

2048*1080P50

NDI

—

—

—

—

—

—

—

—

—

1280*720P50

1280*720P59.94

1280*720P60

1920*1080I50

1920*1080I60

1920*1080I60

—

—

1920*1080P24

1920*1080P24

1920*1080P25

1920*1080P30

1920*1080P30

—

1920*1080P50

1920*1080P59.94

1920*1080P60

—

—

—

—

—

—

—

—

—

—

—

—

—

20

Input terminal Signal format shown in the Status Display as

No.

40

2048×1080/59.94P

41

42

43

44

45

46

47

48

49

50

51

52

53

54

55

56

57

58

59

60

61

2048×1080/60P

3840×2160/23.98P

3840×2160/24P

3840×2160/25P

3840×2160/29.97P

3840×2160/30P

3840×2160/47.94P

3840×2160/48P

3840×2160/50P

3840×2160/59.94P

3840×2160/60P

4096×2160/23.98P

4096×2160/24P

4096×2160/25P

4096×2160/29.97P

4096×2160/30P

4096×2160/47.94P

4096×2160/48P

4096×2160/50P

4096×2160/59.94P

4096×2160/60P

Format

SDI1/2

√
√

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

NDI

—

—

√
√
√
√
√

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

HDMI

√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√

SDI

2048×1080/59.94P

2048×1080/60P

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

HDMI

2048*1080P60

2048*1080P60

3840*2160P24

3840*2160P24

3840*2160p25

3840*2160P30

3840*2160P30

3840*2160P50

3840*2160P48

3840*2160P50

3840*2160P60

3840*2160P60

4096*2160P24

4096*2160P24

4096*2160P25

4096*2160P30

4096*2160P30

4096*2160P48

4096*2160P48

4096*2160P50

4096*2160P60

4096*2160P60

NDI

—

—

3840*2160P23.98

3840*2160P24

3840*2160p25

3840*2160P29.97

3840*2160P30

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

※ 3G support level A/level B；support RGB444

21

Troubleshooting

Problem

No video

Possible fault reasons Solution

Monitor have not switched on

Wrong input source is selected.

No NDI signal source is selected

Input voltage is not stable

Signal cable loose/wrong
connection

The battery power is out of
power when powered by battery

The polarity is reversed when
using DIY power supply

The Network segment of monitor
and NDI source is not same.

Signal cable is in poor contact

Check the power connection of monitor,press “POWER”
button on the front panel.

Press “Source” button to change the input source

Select NDI signal in“NDI source”

Reconnect the power

Check signal cable,make sure the signal cable
connection is right

Change a new battery

Reconnect the cable refer to standard power supply.

1. Make sure the segment of monitor and NDI source is same；

2. Switch on “DHCP” function to assign the IP address
automatically

Change a new signal cable

Video signal interference

Image or

color abnormal

Parameters of color is over adjust

Video is distorted

Video show all blue

The “focus assist” function is “ON”

The “False Color” function is “ON”

Monitor is set to mute mode

No audio

output

Audio cable is in poor contact

Audio cable is disconnected or
connect wrong.

SWIT Electronics Co., Ltd.

Add: 10 Hengtong Road, Xin'gang, Nanjing Economic and
Technological Development Zone, Nanjing 210038, P.R.China
Tel: [phone] Email: [e-mail]

Remove interference sources

Upload User mode to “Factory”

Reset the aspect ratio

Switch off “Blue only” function

Switch off “Focus assist” function

Switch off “False Color” function

Turn “MENU/ENTER” knob left and right to adjust volume

Change audio cable

Check and reconnect the audio cable

SWIT Electronics Europe GmbH

Add: Hochstr. 17, 47228 Duisburg, Germany
Tel: [phone] Email: [e-mail]

SWIT Electronics America, Inc

Add: 3350 Scott Boulevard 61-02, Santa Clara, CA 95054, USA
Tel: [phone]-SWIT(7948) Email: [e-mail]

22