Console Sink
®
w ell made for e v e r
INSTALLATION INSTRUCTIONS
www.swissmadison.com | 1-434-623-4766 | info@swissmadison.com
@SwissMadison
#WellMadeForever
CONSOLE SINK INSTALLATION INSTRUCTIONS
PRIOR TO INSTALLATION:
· Inspect product to ensure no damages have occurred while in shipping.
· Observe all plumbing and building codes in accordance with your state and local requirements.
· Floor must be level prior to installation.
· Console height is not adjustable.
· All dimensions are nominal! Be sure to measure your sink prior to installation.
· The step-by-step guidelines in the installation instructions are a general reference. Should there be
any discrepancies, Swiss Madison cannot be held liable. It is recommended to install all Swiss
Madison products by hiring a licensed professional.
· Read installation and maintenance instructions thoroughly before installing. Be sure to use proper
tools and always wear proper personal safety accessories for your protection.
· Two people are recommended to install and move this product.
If you have any questions or concerns please contact us:
1-434-623-4766
info@swissmadison.com
SUGGESTED TOOLS & MATERIALS: INCLUDED PARTS:
Safety
Glasses
Wrench
Caulk
Screwdriver
Drill
Tape
Measure
Level
— 1 —
Console Sink
&
Legs
Mounting
Hardware
CONSOLE SINK INSTALLATION INSTRUCTIONS
1. Assemble Console
· Using the provided hardware assemble the
console as illustrated.
NOTE: Height of console is NOT adjustable.
2a. Drill two holes in the required position on
the wall using a 14mm masonry drill bit, to
a depth of 75mm.
2. Install Sink
· Use your assembled console to mark on the wall
where the bottom of the sink should rest.
· Following the steps illustrated below, install your
sink.
NOTE: Make sure your sink is LEVEL before
marking and securing into place.
Anchor
Metal
Screw
2d. Place the basin in position against the wall.
Locating the fixing bolts through the holes in
the rear of the basin. Push a plastic washer
followed by a metal washer, onto each fixing
bolt.
Plastic
Gasket
Metal
Gasket
Metal
Nut
2b. Push an anchor into each hole.
2c. Screw a fixing bolt into each anchor using
an 8mm spanner until the spanner contacts
the wall.
2e. Screw a metal nut onto each fixing bolt to
secure the basin. Caution: Do not over-tighten,
as this may damage the ceramic.
NOTE: These fixings are suitable for solid walls
only. Plasterboard or stud walls may require
specialist fixings (not supplied).
CAUTION: Take care when drilling walls and
floors to avoid any concealed wires or pipes.
— 2 —
CONSOLE SINK INSTALLATION INSTRUCTIONS
3. Install Console
· Secure your console underneath the sink and to the wall.
NOTE: Solder lug washer may need to be adjusted to properly align your console legs with the sink.
4. Seal Sink
· Apply a bead of caulk around the back edge of
the sink where it meets the wall.
5. Install Plumbing Fixtures
· Connect drain trap to drain, and water
supply connections to faucet according to
manufacturer’s instruction.
· Run water into sink and check for leaks.
— 3 —
1-434-MADISON
®
w ell made for e v e r
(623-4766)
www.swissmadison.com
ONE YEAR LIMITED WARRANTY
Swiss Madison® products are made with quality materials and excellent craftsmanship to provide our
customers with beautiful, durable, long-lasting products. Should there be any defects in materials or
craftsmanship under regular use that are discovered within the first year of installation, Swiss Madison®
will provide replacement parts at no charge, or at its discretion, replace any product or part of the product
that is deemed defective, under normal installation, use, service or maintenance. This warranty applies
only to the original purchaser. Proof of purchase will be required in the instance of a claim.
Swiss Madison® recommends all installations of Swiss Madison® products to be conducted by a
licensed, professional plumber or contractor. Swiss Madison® will not be held responsible for any
damage or product failure due to improper installation, misuse, or failure to utilize a licensed professional
for installation. Swiss Madison® is not responsible for any installation or removal costs.
This One Year Limited Warranty Will Be Voided If:
• The installation recommendations were not followed by the installer
• The product has been moved from its initial place of installation
• The product has in any way been modified from its packaged state
• The product has been subjected to improper maintenance, abuse, misuse, excessive use of
chemicals, accidents, or other damages, etc.
Swiss Madison® makes no implication that its products comply with any local building or plumbing
codes. It is the consumer’s responsibility and obligation to determine local code compliance prior to and
during installation. This warranty extends only to the original purchaser and first consumer.
Swiss Madison® is not responsible for any special, incidental or consequential damages associated with
the installation, replacement, return or use of the original purchaser’s product. This includes, but is not
limited to: freight costs, labor, travel time, lost profit, home damages and other contingent liabilities and
costs (including, without limitation, costs associated with ‘professionals’ or ‘experts’, investigations,
audits, analyses, attorneys and any other professional/hired services).
The Swiss Madison® warranty is a comprehensive and explicit limit of liability. All items not disclosed
within the warranty are not addressable within the responsibility of Swiss Madison®. Certain states have
variances regarding implied warranties; in those situations, we remain fully compliant.
If you have any questions or concerns, please contact us directly at
1-434-MADISON (623-4766)
WARNING: Contents of your order may contain sharp and possibly other harmful pieces and may
cause hazard to children and adults. Swiss Madison® is not responsible in any way for personal
damages.
Loading...