Bidet
®
w ell made for e v e r
INSTALLATION INSTRUCTIONS
www.swissmadison.com | 1-434-623-4766 | info@swissmadison.com
@SwissMadison
#WellMadeForever
BIDET INSTALLATION INSTRUCTIONS
PRIOR TO INSTALLATION:
· Inspect bidet to ensure no damages have occurred while in shipping.
· Observe all plumbing and building codes in accordance with your state and local requirements.
· All dimensions are nominal! Be sure to measure your bidet prior to installation.
· The step-by-step guidelines in the installation instructions are a general reference. Should there be
any discrepancies, Swiss Madison cannot be held liable. It is recommended to install all Swiss
Madison products by hiring a licensed professional.
· Read installation and maintenance instructions thoroughly before installing. Be sure to use proper
tools and always wear proper personal safety accessories for your protection.
· Two people are recommended to handle and install this product as it is fragile.
· The Bidet cannot be installed on an outside exterior wall.
· A minimum 14" access panel behind the wall where the unit is mounted will be required for
installation and service.
· Please check with your local codes to see if a mixing valve is required for your bidet installation,
to avoid scalding.
If you have any questions or concerns please contact us:
1-434-623-4766
info@swissmadison.com
SUGGESTED TOOLS & MATERIALS:
Safety
Glasses
Putty Knife
Wrench
INCLUDED PARTS:
Level
Tape
Measure
Supply Tube
Sealant
HacksawFlexible
Screwdriver
— 1 —
Bidet
Mounting
Hardware
BIDET INSTALLATION INSTRUCTIONS
BACK-TO-WALL INSTALLATION:
1. Rough-In
· For a side by side toilet/bidet installation, it
is required to have a separation of 24” (610mm)
between units.
· Trap is not included. For installation of a trap in
the floor, provisions must be made.
· Water supplies need to be at least 6” (152mm)
to the left and right of the bidet center line.
· The correct drain center will need to be drilled
through the floor and sleeved (9” from finished
wall) in the center of bidet.
· Install faucet (not included) according to
manufacturer's instructions before installing bidet.
Water supply
6”
24”
6”
9”
24”
2. Set Bidet
· Carefully set the bidet while making sure that the
drain tube is inserted into the waste pipe. Assure the
bidet is centered and level.
· Temporarily set bidet and install provided brackets
to secure later. It is best to stencil an outline of the
bidet on the floor and make measurements
accordingly to fasten the brackets underneath the
bidet.
3. Secure Bidet
· Place wood screws through the plastic
snap-on bases then through the screw holes at
the base of the bidet. With a screwdriver,
tighten the screws 1/2 turn. Do not overtighten
as you may crack the ceramic.
· Snap on bolt caps.
4. Connect Water Supply
· Make sure the 1 ¹⁄2” trap is attached to the drain in the
bottom of the bidet through access panel.
· Connect water supply, it is recommended to have hot
and cold water shutoffs. A mixing valve may be
required to meet your local plumbing codes.
· Turn on water and check for leaks.
· Apply a bead of sealant between bidet, wall and floor
to seal.
— 2 —
1-434-MADISON
®
w ell made for e v e r
(623-4766)
www.swissmadison.com
ONE YEAR LIMITED WARRANTY
Swiss Madison® products are made with quality materials and excellent craftsmanship to provide our
customers with beautiful, durable, long-lasting products. Should there be any defects in materials or
craftsmanship under regular use that are discovered within the first year of installation, Swiss Madison®
will provide replacement parts at no charge, or at its discretion, replace any product or part of the product
that is deemed defective, under normal installation, use, service or maintenance. This warranty applies
only to the original purchaser. Proof of purchase will be required in the instance of a claim.
Swiss Madison® recommends all installations of Swiss Madison® products to be conducted by a
licensed, professional plumber or contractor. Swiss Madison® will not be held responsible for any
damage or product failure due to improper installation, misuse, or failure to utilize a licensed professional
for installation. Swiss Madison® is not responsible for any installation or removal costs.
This One Year Limited Warranty Will Be Voided If:
• The installation recommendations were not followed by the installer
• The product has been moved from its initial place of installation
• The product has in any way been modified from its packaged state
• The product has been subjected to improper maintenance, abuse, misuse, excessive use of
chemicals, accidents, or other damages, etc.
Swiss Madison® makes no implication that its products comply with any local building or plumbing
codes. It is the consumer’s responsibility and obligation to determine local code compliance prior to and
during installation. This warranty extends only to the original purchaser and first consumer.
Swiss Madison® is not responsible for any special, incidental or consequential damages associated with
the installation, replacement, return or use of the original purchaser’s product. This includes, but is not
limited to: freight costs, labor, travel time, lost profit, home damages and other contingent liabilities and
costs (including, without limitation, costs associated with ‘professionals’ or ‘experts’, investigations,
audits, analyses, attorneys and any other professional/hired services).
The Swiss Madison® warranty is a comprehensive and explicit limit of liability. All items not disclosed
within the warranty are not addressable within the responsibility of Swiss Madison®. Certain states have
variances regarding implied warranties; in those situations, we remain fully compliant.
If you have any questions or concerns, please contact us directly at
1-434-MADISON (623-4766)
WARNING: Contents of your order may contain sharp and possibly other harmful pieces and may
cause hazard to children and adults. Swiss Madison® is not responsible in any way for personal
damages.
Loading...