Swisher SR84X054G, SR84X039G, SR84X114G, SR84X084G, SR84X144G User Manual

www.ESP.swisherinc.com

OWNER’S

NUAL

SR84X039G SR84X054G SR84X084G SR84X114G SR84X144G

Starting Serial #: L115-001001

Model SR84X054G Shown

19800 REV 15-001

SWISHER ACQUISITION INC.

1602 CORPORATE DRIVE, WARRENSBURG, MISSOURI 64093

PHONE 660-747-8183 FAX 660-747-8650

Made In The

USA

of US and Global Parts

Near-Absolute Protection

absolute

protection

for you and your family or employees from injury or death caused by the

that, based on our

and

according to the guidance in this publication will have a high probability of

to the original purchaser, the manufacturer will replace any

resulting

confirmed tornado

. This replacement benefit does not include labor to replace the

o be valid this

per all the

(National Storm Shelter

obtained from the

sferable to anyone beyond the original

To obtain this benefit, the owner of the Safe Room must also allow the Manufacturer (or

. The

writing to allow manufacturer to take photographs of the Safe

notify the manufacturer in

. All transportation charges, damage, or loss

incurred during transportation of parts submitted for replacement or repair under this

shall be borne by the purchaser. Should you have any questions concerning this

8183. The model number, serial number,

dealer from

claim can be

ollow all manufacturer’s

(National Storm Shelter Association) Type 4 Seal

This tornado safe room was designed, tested and manufactured by a

Shelter Association (NSSA) in

ts, but may have

assembled and/or installed outside of the control of the Producer

ncluding

the foundation to which this safe room is affixed, is

integral to the

“Having a safe room in your home or small business can help provide near-

dangerous forces of extreme winds. Near-absolute protection means current knowledge of tornadoes and hurricanes, the occupants of a safe room built installed being protected from injury or death.” FEMA – P 320 - 2008

Lifetime Storm Damage Replacement Benefit

For the life of this product and structurally damaged components (excluding accessories) of the Safe Room from a NOAA (National Oceanic and Atmospheric Association) missile impact components, cosmetic damages to any surface, or shipping. For this benefit t Safe Room must have been properly installed (or if moved properly reinstalled) manufacturer’s guidelines, and affixed with a valid NSSA Association) Type 4 Seal (for its current location) which was manufacturer. This replacement benefit is not tran purchaser.

its representative) onsite to inspect the structurally damaged components if requested owner must also agree in Room and to use these photographs and story for marketing purposes at its sole discretion.

In the event you have a claim under this benefit, you must writing either via US mail or electronic mail

benefit benefit, please contact us toll-free at 1-800-222date of purchase, NSSA Type 4 Seal Number and the name of the authorized whom you purchased the product will be needed before any benefit processed.

To maintain this replacement benefit the original owner must perform the following:

1. During installation the original owner must f

installation guidelines, checklists and inspection requirements as needed obtain the NSSA’s which is outlined here:

Producer Member of the National Storm accordance with FEMA, ICC, and NSSA requiremen been Member. The manner, in which this safe room is installed, i

successful performance of this product under extreme weather

ation

Installation Checklist and an Inspection

ith these

The National Storm Shelter Association (NSSA) and the

representative

arrange for inspection by a Qualified Inspector immediately upon

ctor is defined as either a

safe room is installed, a registered architect, a professional engineer, a

NSSA Producer Member or his

The

Inspector should complete the Inspection Checklist, and this Checklist

Member. Upon receipt of the

NSSA

to the shelter to confirm that the shelter meets all FEMA,

contact the

lly

null and

the new location

INSPECTION AND

AIN THE NSSA TYPE

ABSOLUTE

D WILL MAKE ALL

SAFE ROOM

AMAGE REPLACEMENT

will

To exercise this limited warranty the owner must allow the manufacturer (or its

representative) at its discretion to inspect the Safe Room onsite. Failure to allow this

urer will determine if the

conditions. The manufacturer has provided detailed Install Instructions, including an Checklist. Installation must be in strict accordance w instructions. Producer Member recommend that the owner or their

installation of this shelter. A Qualified Inspe local building inspector or the authority having jurisdiction where the

licensed professional inspector, or the qualified safe room installer or qualified technical representative.

should be returned to the Producer completed Checklist, the Producer Member will issue a Type 4 Seal to affix ICC, and NSSA standards. We encourage you to manufacturer of this shelter with any questions that you may have.

b. If the original purchaser removes the Safe Room from its origina

installed location all warranties and benefits are immediately void. However, if the original owner follows all the required installation, inspection and certification procedures at then the replacement benefit can be reinstated.

FAILING TO FOLLOW ALL THE INSTALLATION, DOCUMENTATION PROCEDURES REQUIRED TO OBT 4 SEAL THE SAFE ROOM MAY NOT DELIVER THE NEARPROTECTION IT WAS DESIGNED TO PROVIDE AN BENEFITS PROVIDED TO THE PURCHASER UNDER THE LIMITED WARRANTY AND LIFETIME STORM D BENEFIT NULL AND VOID.

5 Year Manufacturer’s Limited Warranty

The manufacturer’s limited warranty to the original consumer purchaser is as follows: The Safe Room is free from defects in materials and workmanship for a period of five (5) years from the date of purchase by the original consumer purchaser. The manufacturer repair or replace, at its discretion, parts found to be defective due to materials o workmanship only.

inspection will void the warranty. Upon inspection, the manufact damaged or malfunctioning components will be repaired or replaced.

Limitations and Exclusions

ducts which have been

uctions

product

assembly or

arranty

ormal wear, normal

Small damage to the powder coat finish

tallation, or from normal wear and

tear. To reduce the likelihood of rusting, the owner should repair any damage to

warranty is not

notify the

. All transportation charges,

damage, or loss incurred during transportation of parts submitted for replacement or

warranty shall be borne by the purchaser. Should you have any

8183.

and the

dealer from whom you purchased the product will be needed

WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR

CONSEQUENTIAL DAMAGES AND ANY IMPLIED WARRANTIES ARE

HE SAME TIME PERIODS STATED HEREIN FOR ALL

. Some states do not allow the limitation of

consequential damages or limitations on how long an implied warranty may last, so the

warranty gives you

state. This is

This limited warranty is subject to the following limitations and exclusions:

1) Limitation - This limited warranty applies only to pro properly assembled, adjusted, and operated in accordance with the instr contained within this manual. This limited warranty does not apply to any that has been subject to alteration, misuse, abuse, improper installation, shipping damage, or to normal wear of product. This limited w does not apply to damage caused by any act of man or any natural event.

2) Exclusions - Excluded from this limited warranty are: N adjustments, and normal maintenance. that may have occurred during shipping, ins

the powder coat finish as soon as possible. This limited transferable to anyone beyond the original purchaser.

In the event you have a claim under this limited warranty, you must manufacturer in writing either via US mail or electronic mail

repair under this limited questions concerning this limited warranty, please contact us toll-free at 1-800-222The model number, serial number, date of purchase, NSSA Type 4 Seal Number name of the authorized before any limited warranty claim can be processed.

THIS LIMITED

LIMITED TO T EXPRESSED WARRANTIES

above limitations or exclusions may not apply to you. This limited specific legal rights and you may have other rights, which vary from state-toa limited warranty as defined by the Magnuson-Moss Act of 1975.

When Choosing a Location For Your Safety Shelter:

1) Location of Shelter is at the minimum elevation of the lowest floor required by the floodplain ordinance of the community, or One Foot above the flood elevation corresponding to the highest recorded elevation if the area is not in a mapped special flood hazard area or is in a mapped nonparticipating community.

2) Shelter is located within the interior of a residence or located within 150 feet of the residence it is intended to serve. If located outside the residence, shelter is protected from all external weather conditions.

3) Do not locate the Safety Shelter over an expansion joint in the concrete slab.

4) Do not locate the Safety Shelter in a low or potentially wet area. If the Safety Shelter is allowed to sit in water or a damp area, damage may result that is not covered by the manufacturer’s warranty.

5) Do not locate Safety Shelter closer than three (3) feet to any electrical or gas appliance.

6) Do not locate Safety Shelter where it will block access to any electrical panel or breaker box.

7) Do not locate Safety Shelter closer than 2” from any wall or structure. The side of the Safety Shelter you install the Lower and Upper Wall Panel Assembly should be far enough away from any wall or structure to allow a person to be able to safely walk between. See pgs 12 & 19 of this manual and the yellow Emergency Exit Instruction Sheet (PN 20056) for additional information.

8) Do not store any items in a manner that would block any of the Safety Shelter vents.

Operating and Safety Instructions

Safety Precautions

1) Your ESP Safety Shelter has been designed and certified by Professional Registered Engineers and physically tested at Texas Tech University to ensure that it meets or exceeds FEMA –P320 Guidelines and the ICC 500-2014 Specifications.

2) Your Safety Shelter also meets the standards set for by the National Storm Shelter Association (NSSA) and once properly installed can bear their Seal.

3) NEVER allow children to play in or around the Safety Shelter.

4) Keep the Safety Shelter locked at all times and place the key out of reach of children but where it can be located quickly in case of emergency.

5) When closing door from the inside one hand must be on the long handle located on the door jamb and the other hand on the inside door handle. NEVER place hands on or near either edge of the door or the door jamb while closing the door. Failure to strictly follow this procedure could result in serious injury to the user.

6) NEVER attempt to attach any type of AC (alternating current) or high voltage lighting fixtures or appliance to the Safety Shelter without first consulting a licensed electrician and your local electrical codes. Failure to strictly comply with all applicable electrical codes could result in serious injury and/or death. Battery operated lights and appliances can be used inside the Safety Shelter.

7) NEVER store flammable materials or fuel in your Safety Shelter.

8) NEVER have an open flame in your Safety Shelter. An open flame could deplete the oxygen in the room and cause asphyxiation.

9) Keep a flashlight(s) or other battery operated lights inside the Safety Shelter. Check or replace the batteries in these lights twice per year.

10) Become familiar with your Safety Shelter and the operation of the door, so that in case of an emergency you can open and close it quickly and safely.

11) NEVER store any items in front of the Safety Shelter that would block access to the door in the event of an emergency.

12) Establish and practice a plan for all family members to meet and enter the Safety Shelter in case of an emergency. Practice the plan at least once a year.

13) When entering the Safety Shelter during a storm be aware that the floor may be wet and slippery from water entering the open door (depending upon the location).

14) You should always take a mobile phone with you into the Safety Shelter so you can contact emergency help if needed. However, if you forget your phone during a Tornado Watch or Warning do not leave the Safety Shelter to retrieve your phone.

15) Any time the National Weather Service issues a Tornado Watch or Warning for your area you should enter the Safety Shelter.

16) We suggest stocking your Safety Shelter with provisions and supplies so that it is ready when needed.

Safety Shelter Periodic Inspection

At least twice a year inspect the operation of the Safety Shelter.

Inspect the outside of the Safety Shelter for items blocking the door or any vents. Remove these items if found.

Unlock the Safety Shelter Door.

Slide the door to the fully open position. If the door does not slide freely look for obstructions behind the door or inside the door’s overhead rail and remove. The bearings inside the door rollers are sealed for the life of the Safety Shelter and should not need lubrication.

8) With the door closed and the deadbolt in the locked position insert the

Using a flashlight or lights inside the Safety Shelter move the door latch handle. Everything should move freely without binding. Adjust and/or apply light oil to all joints if necessary.

Close the door. In the closed position the latch must fully engage over the three latch pins (without force). If not, follow the procedures in the Installation Instructions for alignment of the door.

Turn the deadbolt to the locked position and attempt to unlatch the door with the knurled door handle. The handle should not move or in any manner unlatch the door from the three latch pins. If the deadbolt fails to prevent the handle from unlatching the door check the deadbolt lock for proper operation and engagement into the latch bar.

Locking Pin through the Door Jamb, Door and Latch Bar. Once fully inserted through the Jamb rotate the Latching Pin 90° counterclockwise so the handle is down. Unlock the deadbolt and attempt to open the door with the latch handle. The Locking Pin should not allow the door to unlatch, even with the deadbolt unlocked.

9) Relock the deadbolt and remove all three Latch Pins and the Locking Pin from the Door Jamb. The door should open freely for an emergency escape.

10) Reinstall the three Latch Pins, exit the Safety Shelter and close the door. Test that the door is fully latched onto the pins by pulling strongly on the door to the right. Lock the deadbolt and attempt to open the door by pulling on the Handle. If it does open follow the Installation Instructions for alignment of the door.

11) Once a year check the torque on all anchor bolts to 40 ft-lbs and all other bolts in the Safety Shelter to 31 ft-lbs.

ety Shelter Periodic Maintenance

Saf

To clean your Safety Shelter use warm water and a damp rag with dish soap. Thoroughly rinse with water and dry.

Solvents and harsh chemicals should NEVER be used on the Safety Shelter. They will damage the powder coat finish causing the metal to rust and will void the Warranty.

NEVER attempt to repair the Safety Shelter yourself. Call the manufacturer at 800-222-8183.

Once every year lubricate all moving joints on the door latch mechanism with light (3n1) oil.

Safety Shelter Operation Instructions

1) Children should NEVER be allowed to play near or in the Safety Shelter.

Your Safety Shelter can be used for many purposes: 1) As a Storm Shelter to provide near-absolute protection from wind blown debris during a Tornadic event or sever wind storm, 2) as a panic room or safe place of harbor during a home invasion or similar type event, and 3) as a vault to store valuable items. If used as a vault be sure that no items are placed in the Safety Shelter that would inhibit a person from using it as a Storm Shelter or Panic Room.

Be sure to store the key to the Safety Shelter deadbolt out of reach of children but where an adult can get to it easily and quickly.

To be ready for any type of event equip your Safety Shelter with a minimum list of supplies: first aid kit, weather radio (with extra batteries), ear plugs of the appropriate size and quantity for everyone expected to use the Safety Shelter, drinking water (approximately one (1) gallon per person), books and games to keep children occupied, extra flashlights (with extra batteries and suggest one flashlight for each person using the Safety Shelter). Other items could be included as deemed necessary.

Have a family meeting and make an emergency plan. Practice your plan once a year including entering and exiting the Safety Shelter. This will also allow everyone an opportunity to become comfortable inside the Safety Shelter.

You should always take a mobile phone with you into the Safety Shelter so you can contact emergency help if needed. However, if you forget your phone during a Tornado Watch or Warning do not leave the Safety Shelter to retrieve your phone.

Family members that are old enough to be left home alone should be trained on how to properly and safely use the Safety Shelter. A plan should be established and practiced just for them.

10) To open the door from the outside, rotate the handle to the right and pull the

11) Enter the Safety Shelter and be sure everyone is accounted for.

12) Be sure everyone is clear of the door. Place your right hand on the vertical

13) To ensure the door has properly latched push the Black Knurled Door Handle

To prevent children from playing inside the Safety Shelter it is recommended that it remain locked at all times.

To enter the Safety Shelter unlock the deadbolt and remove the key from the deadbolt. Take the key with you into the Safety Shelter.

door from left to right. Slide the door all the way to the right until it is fully opened.

handle on the door jamb. Then, grasp the round vertical Door Handle Bar (not the black knurled handle) with your left hand and pull the door closed to the right until it latches inside the door jamb and all three pins are engaged.

to the right and visibly check that the latch bar is fully engaged over the three latch pins. Lock the Deadbolt lock by turning the thumb latch to the right. Grab the vertical door handle and pull back to the left to ensure the door is properly latched. If the door opens, repeat the previous steps above until the door latches to the jamb properly and all three latches pins are engaged.

14) Install the Locking Pin into the Key Hole in the Door Jamb. The Locking Pin must go through five (5) sections; two (2) sides of the door jamb, two (2) sides of the door, and one (1) Latch Bar inside the door. Rotate the handle of the Locking Pin counterclockwise so that the handle is pointing down. This Locking Pin positively locks all three members together and provides nearabsolute protection from the door opening under a sever wind event.. This Locking Pin should remain in the locked (down) position until it is safe to exit the Safety Shelter.

15) During a high wind event NEVER allow a person to be closer than 3” to any exterior wall or door of the Safety Shelter. If sitting on a bench, do not lean back against the wall during an event.

16) In the event of a direct hit or damage outside, it is recommended not to leave the Safety Shelter until emergency personnel arrive to assist. There may be unforeseen hazards directly outside the Safety Shelter created by the storm that could cause serious injury or death. If you have a cell phone in the Safety Shelter with you call 911 and let them know your location. If you must exit the Safety Shelter prior to emergency personnel arriving, do so with extreme caution and be aware of all your surroundings.

17) You should also listen to your weather radio to determine when it is safe to leave your Safety Shelter. Just because the wind has slowed, does not mean it is safe to exit!

19) To exit the Safety Shelter, Remove the Locking Pin, move the Black Knurled Door Handle to the left and slide the door open to the left. Exit the Safety Shelter to a safe location.

20) If for any reason any part of the door latching mechanism becomes damaged and inoperable causing the door to not open, there is a failsafe relief method to get the door open. First, rotate and remove the Locking Pin from the Jamb. Second, there are three Latch Pins in the jamb. Remove the Cotter Pins from the back of these pins and then pull these three pins out of the jamb. The door will now open no matter how it is locked. This can only be performed from inside the Safety Shelter.

21) In the unlikely event that the door or exit path beyond the door becomes blocked by debris, the Lower and Upper Wall Panel Assembly can be disassembled from the inside of the Safety Shelter using the supplied Wrench (PN 20075Y) or similar tools. See pgs 12, 19 and 25 of this manual and the yellow Emergency Exit Instruction Sheet (PN 20056) for additional information.

ommended Tools For Assembly:

Rec

• Leather Gloves

• Safety Glasses

• Flashlight

• (1) Hammer Drill with 1/2” Carbide Concrete Drill Bits (Do Not Use Diamond Bits)

• (1) Hammer

• (1) Torque Wrench Capable of 40 Ft-lbs

• (1) 9/16” Open End Wrench or Socket Wrench

• (1) 3/8” Drive X 9/16” Deep Well Socket Wrench & Extension

• (2) 3/4” Open End Wrenches

• (1) 3/4” Deep Well Socket Wrench

• (1) Screwdriver or Punch for Aligning Holes

Note: The supplied Wrench (PN 20075Y) is intended to be used in an emergency. It is not recommended to be used to assemble the Safety Shelter.

ANCHOR BOLT ALIGNMENT TEMPLATES

Item #

Part #

Description

1 19794 Template - Anchor Bolt, Front Left 2 19795 Template - Anchor Bolt, Rear Left 3 19796 Template - Anchor Bolt, 30" 4 19797 Template - Anchor Bolt, 60" 5 19798 Template - Anchor Bolt, Front Right 6 19849 Template - Anchor Bolt, Rear Right 7 20195 Template - Anchor Bolt, 15"

ASSEMBLY

Some components have been hidden for clarity.

The Center Roof Panel (item 24) is not included with model SR84X039G.

It is essential that the Lower and Upper Wal

l Panel Assembly (items 32, 33 & 34) be positioned so that in the event of an emergency they can be disassembled to allow for a safe exit. Do not place these panels against a wall or other obstruction. See Step 1 on pg 21 of this Manual and the yellow Emergency Exit Instruction Sheet (PN 20056). It is recommended that you keep the supplied Wrench (item 35) or similar tools, this manual and the yellow Emergency Exit Instruction Sheet in the Safety Shelter at all times. The supplied Wrench is intended to be used in an emergency. It is not recommended to be used to assemble the Safety Shelter.

+ 28 hidden pages