Swisher GC-14 Owners Manual
MANUFACTURING QUALITY LAWN CARE EQUIPMENT SINCE 1945
Owner’s
Manual
GC-14
IMPORTANT
Read and follow all
Safety Precautions
and Instructions
Before Operating this
Equipment.
14 Cubic Ft.
Garden Cart
Made In CHINA
1602 CORPORATE DRIVE, PO BOX 67, WARRENSBURG, MISSOURI 64093
PH 660. 747. 8183 FAX 660. 747. 8650
swisherinc.com
11621 REV. 05-269
RULES FOR SAFE OPERATION
package with parts as shown in the chart below
ASSEMBLY INSTRUCTIONS
Preventing accidents is the responsibility of every TOOLS REQUIRED
equipment operator. The following general safety (1) Screw Driver
precautions must be fully understood and followed (1) Pliers
by every operator. (1)10mm Wrench
1. Do not at any time carry passengers in this cart. It
is designed for carrying materials only and not When assembling your cart, place the heads of all
intended to carry passengers. screws to the inside and hex nuts with flat washers
2. Be careful on any grade (hill) and stay off of steep to the outside.
grades.
3. Use caution when loading cart to avoid tipping. 1. Lay the front angle assembly down (flat) on floor
4. Avoid large holes and ditches when transporting and stand the bottom panel in position as shown in
loads. figure 2.
Your Farm/Yard Cart carton contains a hardware
NOTE
The bottom panel has one galvanized
and in figure 1.
edge; this is the rear. The front edge
has three holes. See figure 2.
Contents of Hardware Pack: (See figure 1)
REF. QTY. DESCRIPTION
A 6 Screws,M6X50 2. Line up three holes in bottom panel with holes in
B 2 Screws,M6X40 front angle assembly. Start three M6X25 screws
C 8 Screws,M6X30 through bottom panel, then through angle. Secure
D 21 Screws,M6X25 screws with flat washers and hex nuts.
E 4 Cotter Pins
Finger tight at this time.
See figure 2.
F 37 Hex Nuts,M6
G 33 Flat Washer,Ф6
H 4 Lock Washer,Ф6
I 4 Large Flat Washer
BOTTOM
PANEL
HARDWARE REFERENCE CHART
B
A
M6X40
C
M6X25
M6X30
D
E
M6
HEX
NUT
Ф
6
FLAT
WASHER
M6X25
SCREW
THREE
HOLES
FRONT
EDGE
Make only
FRONT
ANGLE
ASSEMBLY
M6X50
F
G
H
FIGURE 1
I
FIGURE 2
2
3. Turn the front angle assembly and bottom panel 7. Stand the cart on end with the front angle assemupside down as shown in figure 3. bly down on the floor. Temporarily place the four
large flat washers (axle washers) on
4. Lay each side angle on the bottom panel so that the inside of front angle assembly. See figure 5.
the two holes (for the axle clamp) are closer to the
front angle assembly. See figure 3.
NOTE
These washers act as shims and are
5. Secure both axle clamps to the side angles and
the bottom panel using four M6X30 screws,
lock washers and hex nuts.
until the axle is assembled. See figure 3.
tight
M6
HEX
NUT
SIDE
ANGLE
AXLE
CLAMP
M6X30
SCREW
Make only finger
Ф
6
LOCK
WASHER
FRONT
ANGLE
ASS'Y
just for assembly purposes. You will
remove them later to use on axle.
BOTTOM
PANEL
LARGE
FLAT
WASHER
FRONT
ANGLE
BOTTOM
PANEL
SIDE
ANGLE
ASS'Y
FIGURE 5
8. Lay the front panel down onto the front angle
FIGURE 3
assembly, on top of the four large washers.
6. Assemble four M6X25 screws, flat washers and See figure 6.
hex nuts to the side angles and bottom panel
using the holes on each side of the axle clamps.
Tighten the four nuts.
Ф
6
FLAT
WASHER
M6X25
SCREW
See figure 4.
M6
HEX
NUT
FRONT
PANEL
FRONT
PANEL
FRONT
ANGLE
ASS'Y
LARGE
FLAT
WASHER
FIGURE 4 FIGURE 6
3
Loading...