Swisher 11730 User Manual

Owners
Manual

MODEL NO.
11730

swisherinc.com

TRUCK SPREADER

TRUCK SPREADER

TRUCK SPREADERTRUCK SPREADER

IMPORTANT
Read and follow all
Safety Precautions
and Instructions
before operating this
equipment.

REV 08-086

1602 CORPORATE DRIVE, P.O. BOX 67, WARRENSBURG, MISSOURI 64093
PHONE [phone] FAX [phone]

Assembly
Replacement Parts

Made In The

Manufacturing quality lawn care equipment since 1945

12000

USA

The manufacturer’s warranty to the original consumer purchaser is: This

ted to ninety (90) days

This warranty applies only to products which have

LIMITED WARRANTY

product is free from defects in materials and workmanship for a period
of one (1) year from the date of purchase by the original consumer
purchaser. We will repair or replace, at our discretion, parts found to be
defective due to materials or workmanship. This warranty is subject to
the following limitations and exclusions:

1) Commercial Use The warranty period for any product used for
commercial or rental is limi
from the date of original purchase.

2) Limitations
been properly assembled, adjusted, and operated
in accordance with the instructions contained
within this manual. This warranty does not apply
to any product of Swisher Mower Co., Inc., that
has been subject to alteration, misuse, abuse,
improper assembly or installation, or shipping
damage.

3) Exclusions Excluded from this warranty are normal wear,
normal adjustments, and normal maintenance.

Item # Part # Description

1 10113 Deflector - Spreader
2 NB505 Bolt - 5/16-18 X 1 1/2 HCC GR5 ZY
3 NB556 Washer - USS Flat, 5/16 ZY
4 NB579 Washer - Fender, 5/16 X 1 1/4 OD ZY
5 7825Z Bushing - Lift Bar
6 10051 Spring - Gate, 12V ATV Spreader
7 NB555 Washer - USS Flat, 1/2 ZY
8 10112TK Gate - Hopper

9 10111TK Bracket - Motor Support, Upper
10 NB181 Nut - Nyloc 5/16-18 ZY
18 10192 Washer - Nylon Retainer 5/16"
20 10975 Tank - Truck Spreader

Step 1:

Assemble the components as shown.
Use the Nylon Retainer Washer (18)
to hold the parts together.

Step 2:

Attach the assembly
made in Step 1 to the
tank (20) by sliding the
bolts (2) up through the
tank and placing a
fender washer (4) over
each bolt. Thread a nut
(10) over each bolt and
tighten securely.

NOTE: To change the amount of material being spread,

adjust the hopper gate by pulling on the handle
until the desired flow is attained. A scale of one
to four has been provided with one being the
least amount, and four being the most. Zero
will seal the material from being distributed.

Item # Part # Description

9 10111TK Bracket - Motor Support, Upper
11 10114TK Bracket - Motor Support, Lower
12 10197 Bolt - Carriage 5/16-18 X 1 GR5
13 10117TK Shield - Spreader
14 3844 Knob - T, 5/16-18
15 15118 Motor - Spreader 12 VDC CW 2.5"
16 10118 Spinner - Distributor, Spreader

Step 3:

Remove the nuts and snap ring from
the motor and place the Lower Motor
Support Bracket (11) over the Motor (15).
Thread the nuts onto the motor studs and
tighten. Slide the Spinner/Distributor (16)
over the motor shaft and replace roll pin.

Step 4:

Insert the 5/16” Carriage Bolts (12)
into the Lower Motor Bracket (11),
through the Upper Motor Bracket (9),
and through the Spreader Shield (13).
Place the T-Knobs (14) on the bolts (12)
and tighten. (The guide of the
Lower Bracket will slide up
through the slot in the Upper
Bracket).

NOTE: To change the radius of

material being spread, simply
loosen the T-Knobs and slide
the mechanism up (smaller
radii) or down (larger radii).

Item # Part # Description

3 NB556 Washer - USS Flat, 5/16 ZY
10 NB181 Nut - Nyloc 5/16-18 ZY
21 10976TK Support - Weldment, LH; Truck Spreader
22 10979TK Support - Weldment RH; Truck Spreader
24 NB501 Bolt - 5/16-18 X 1 HCC GR5 ZY
25 NB579 Washer - Fender, 5/16 X 1 1/4 OD ZY GR2

Step 5:

Attach the Support Tube Weldments
(21 & 22) to the tank by inserting the
bolts (24) through the Washers (25) and
the Weldments (21 & 22), and into the
holes on the side of the tank as shown.
Place a washer (3) over each bolt (24) on
the inside of the tank and thread the nuts
(10) onto the bolts (24) and tighten securely.

Item # Part # Description

10 NB181 Nut - Nyloc 5/16-18 ZY
23 10981TK Mount - Weldment; Truck Spreader
25 NB579 Washer - Fender, 5/16 X 1 1/4 OD ZY GR2
26 9855 Bolt - U, Sq 3/8-16 x 1 5/8" x 2 1/2"
27 11728TK Support - Weldment; Truck Spreader

10176 Lid - Tank
10531 Adapter - Kit, 12 Volt

Step 6:
Attach the Mounting Weldment (23) to the Spreader Assembly by
putting the U-Bolts (26) over the Mounting Tubes (21 & 22) and into
the holes on the Mounting Weldment (23). Mount the Support
Weldment (27) onto the rear of the Mount Weldment (23) and place
the Washers (27) onto the Bolts (26) as shown and thread the Nuts (10)
in place. Making sure that the support tubes are resting on the lip
provided, tighten the nuts, securing the Mounting Weldment (23) and
Support Weldment (27) to the Spreader Assembly.

MANUFACTURING QUALITY LAWN CARE EQUIPMENT SINCE 1945

Owner’s
Manual

Model Numbers

Truck

Spreader

11730

WHEN ORDERING PARTS, PLEASE HAVE THE

FOLLOWING INFORMATION AVAILABLE:

* PRODUCT – ________________
* SERIAL NUMBER - _______________
* MODEL NUMBER - _______________

TYPE - _______________

* PART NUMBER WITH PAINT CODE

* PART DESCRIPTION

IMPORTANT

Read and follow all

Safety Precautions

and Instructions

Before Operating this

Equipment.

TELEPHONE - 1-800-222-8183

FAX - 1-660-747-8650

SWISHER MOWER & MACHINE CO. INC.

SWISHER MOWER & MACHINE CO. INC.

SWISHER MOWER & MACHINE CO. INC.SWISHER MOWER & MACHINE CO. INC.

1602 CORPORATE DRIVE

P.O. BOX 67

WARRENSBURG, MO 64093

swisherinc.com