Swing-N-Slide Olympus WS 5031, Olympus WS 5032, Olympus WS 5033 Instructions Manual
Olympus Wave Slide Instructions
WARNING: Assembly by adult.
AVERTISSEMENT: L’assemblage dolt être exécuté par un adulte.
ADVERTENCIA: El ensamblaje lo debe hacer un adulto.
WARNING: ASSEMBLY BY ADULT.
WS 5031,
WS 5032, WS 5033
Fits 60” (152,4 cm) Deck Height
KIT INCLUDES:
Not Included In Kit:
Cut
1-3/4”
(4,4 cm)
17” (43,1 cm)
1-3/4” (4,4 cm)
Stake
2” x 4” x 17” (5,1 x 10,2 x 43,1 cm)
Use Pressure-Treated Wood
x1
Tools Required:
Phillips Bit
WARNING: ASSEMBLY BY ADULT
x11
Hex Bolt
x11
x22
Deck Screw
x2
1-1/4”
(3,2 cm)
Screw size should be a #8 thread size
minimum and coated for use
with treated wood.
FOR PRIVATE USE ONLY
DO NOT USE IN PUBLIC SETTNGS!
x2
1/2”
(12,7 mm)
Truss Screw
x4
1-1/4”
(3,2 cm)
Screw must be to sizes shown at a
minimum. Do not use a screw size
shorter than 1-1/4” (3,2 cm) long.
(6 mm)
1/4”
1/8” & 1/4” Drill Bits
Electric Drill
ASSEMBLY STEPS
1. Align slide sections and the backing plates together on
the ground (Fig. 1). Begin attaching two slide sections
together by securing the bolts in place fi nger tight (see
Fig. 2 for proper Bolt Sequence). Following this pattern
install (1) bolt, (2) washers and (1) lock-nut per hole
(see Fig. 1).
Once all (11) bolts, (22) fl at washers and (11) lock-nuts
are in place go back and tighten all hardware with
appropriate tools.
IMPORTANT: Tighten securely so backing plates
and slide sections are tight against each other AND
there are a minimum of one to two threads extending
beyond each lock-nut.
8
9
4
10
Backing Plates
11
2
Fig. 2
Tape Measure
Hammer
Circular Saw
Socket Wrench set /
Wrenches
Fig. 1
Backing Plates
(11) 5/16” (7,8 mm) Lock-nut
(22) 5/16” (7,8 mm)
Flat Washers
(11) 5/16” x 1”
(7,8 mm x 19 mm)
Hex Head Bolt
7
6
3
5
1
Tighten nut until washers are tight against backing plates.
Weight Limit: 250 lbs
For children 2-10 years of age
Specifi cations subject to change without notice.
Manufactured for: Swing-N-Slide® • 1212 Barberry Drive • Janesville, Wisconsin 53545 • USA • 1-800-888-1232 • www.swing-n-slide.com
Made in USA • Printed in USA
1
LDR 03-08-2019 LA 5940
Assembly:
Fig. 44b
Fig. 3
Pre-drill dimple holes through slide with 1/4” drill bit fi rst
x4
USE ZONE
72”
Pre-drill holes in slide with
1/8” drill bit fi rst
(2) 1-1/4” screws
(not included)
Stake
2” x 4” x 1 7”
Use Pressure-Treated Wood
21”
21”
1-3/4” Minimum
Fig. 4
2” above ground
1-3/4”
Minimum
1-1/4” Truss Screws (not included)
Fig. 5
ASSEMBLY STEPS
1. Consult (Fig. 3) for proper placement of slide on your unit. Make certain no objects lie within the grayed out area, or ‘Use Zone.’ Position slide to determine
proper location for stake. IMPORTANT: Place the slide on level ground, not less than six feet from any structure or obstruction such as a fence, garage, house,
overhanging branch, laundry line or electric wire. Protective surfacing must extend a minimum of 6ft. in all directions from the perimeter of the equipment or from
the outermost edges of any component. A slide extending beyond the platform must have protective surfacing at least 6ft. out from both sides as well as the
end. An area of 21” on either side of the slide should be free of obstructions which a child’s arm could contact.
2. Drive wood stake (not included) into ground leaving 2” exposed. (Fig. 4)
3. Using an 1/8” drill bit, drill (2) holes through the side of the slide and into stake. Secure the slide bottom to the stake using (2) 1-1/4” deck screws (Fig. 4).
4. Attach slide to unit as shown in (Fig. 5).
Important: Slide has four sets of dimples. Use one screw at each set of dimples. Avoid locating dimples over any gaps in the playset deck.
Check for screws protruding underneath the deck.
If screws protrude, add a wooden slide block underneath the deck to cover screw ends. See Fig. 6 for an example slide block.
Fig. 6
Weight Limit: 250 lbs For children 2-10 years of age
Screw
Deck
Deck Screw
Slide Block
Specifi cations subject to change without notice.
Manufactured for Swing-N-Slide® • 1212 Barberry Drive • Janesville, Wisconsin 53545 • USA • 1-800-888-1232 • www.swing-n-slide.com
Made in USA • Printed in USA
2
LDR 03-08-2019 LA 5940
Loading...