Swimline 50050 User Manual Page 2
Item # 50050
Aluminum Reel System
For In Ground
4. Depending upon the size of your pool you will also require one of the following tube kits:
(Tube Assembly is detailed below and on back cover)
Solar Pool Covers
1. Congratulation on your purchase of our PREMIUM ALUMINUM Solar Reel System for Above Ground Pools.
Please follow the instructions carefully so as to not void our warranty.
2. Please use your solar blanket and reel assembly in the manner it was intended for:
a. Your solar blanket is not a safety cover
b. Remove the solar blanket and Solar Reel assembly from the pool completely before swimming use.
c. Do not store the solar blanket on the ground in direct sunlight, as it will burn the lawn
3. Preparation & Assembly: Check inventory of all items and assemble as illustrated below:
Allen
Screw
Alum.
Base
Post
Base
Safety
Cap
Lock
Collar
Crank
Allen
Wrench
Allen
Screw
Base
Safety
Cap
Axle
Bearings
Alum.
Base
Post
Resin
Mount Bracket
Alum.
Base
Hold Down
Screw
(2 Pcs.)
Aluminum Tube
Inserts
Axle
Bolt
Aluminum
Tubing
(Depending On Your Tube Kit
Pre-Drills & Hardware May Vary)
Quick Release
Pins
Axle
Bearings
Axle
Bolt
Alum.
Base
Hold Down
Screw
Resin
Mount Bracket
Lock
Collar
Axle
Item #51120 3” Tube Kit
Contains
(1) 59-1/2" x 2.920" Diameter
extruded aluminum shaft
(2) 59-1/2" x 2.745" Diameter
extruded aluminum shaft
(4) 3” Through Bolts
(1) Drill Bit
Item #51160 3” Tube Kit
Contains:
(1) 72" x 2.920" Diameter
extruded aluminum shaft
(2) 72" x 2.745" Diameter
extruded aluminum shaft
(4) 3” Through Bolts
(1) Drill Bit
Item #51200 3” Tube Kit
Contains:
(2) 59-1/2" x 2.920" Diameter
extruded aluminum shaft
(3) 59-1/2" x 2.745" Diameter
extruded aluminum shaft
With (8) 3” Through Bolts
(1) Drill Bit
Item #51240 3” Tube Kit
Contains:
(2) 68" x 2.920" Diameter
extruded aluminum shaft
(3) 68" x 2.745" Diameter
extruded aluminum shaft
With (8) 3” Through Bolts
(1) Drill Bit
Item #51284 4” Tube Kit
Contains:
(3) 58" x 3.80" Diameter
extruded aluminum shaft
(4) 58" x 3.725" Diameter
extruded aluminum shaft
With (8) 3” Through Bolts
(1) Drill Bit
(2) 4”x 6” Aluminum tube inserts
5. Positioning Your Solar Reel:
For Rectangular pools, place top-rail brackets at either end of pool.
For Oval pools, place top-rail brackets at either end of pool where radius begins.
For Round pools, place top-rail brackets at center of pool. (See Illustrations below)
Fig. A
Unroll Unroll Unroll Unroll Unroll
RECTANGULAR OVAL ROUND
6. Trimming Your Solar Blanket:
• Lay your Solar Blanket (not provided) on top of water.
IMPORTANT! Oval & Round Pool owners will need to fold their solar covers at point of placement
of brackets! The cover will unroll left and right of brackets & cross pole. Please allow 6 inches more
material on length to allow for a fold where straps will be attached for wind onto reel system. (See Fig A above)
• With scissors trim blanket to fit shape of pool. Be sure to clear the inside top rail of pool.
PARTS LIST
(2) Resin Mounting Brackets
(2) Aluminum Bases
(2) Aluminum Base Posts
(4) Axle Bearings (Installed)
(2) Lock collars w/ Allen screws
(1) Allen Wrench for lock collar
(1) 3” Aluminum Tube Insert
(1) 3” Aluminum Tube Insert w/ Axle
(2) Base Safety Caps
(2) Hold Down Screws
(2) Quick Release Pins
(1) Strap Kit
(8) Self Drilling Mounting Screws
(2) 3.25” SS Axle Bolts & Nuts
STRAP KIT
(11 Pcs.)
Plastic Screw
(1 extra piece)
(21 Pcs.)
Plastic Strap Plate
(1 extra piece)
(11 Pcs.)
Stainless Steel
Self-Drilling Screws
(1 extra piece)
(1 Pc.)
Driver Bit
(10 Pcs.) Fabric Straps
(1 extra piece)
7. Mounting your Solar Reel Brackets: Exercise caution before drilling any holes in your top rail to avoid damaging the wall or liner.
Plastic Mounting Bracket - Use of plastic mounting bracket allows you to slide the aluminum base out of bracket and store the
complete reel system out of way when pool is in use. Locate area on top rail of pool where you want to mount your reel system.
Plastic mounting bracket is attached to the top rail with self-drilling screws through the four counter sunk holes in the bracket.
8. Assembling The Tube Kit:
All tube kits consist of 6 sided Hexagon shaped aluminum tubing. There are two sizes of tubing, the smaller size nesting into
the larger size. All tube kits begin and end with the smaller diameter tubes. The Aluminum tube inserts require
CAREFUL ALIGNMENT! (See illustration below for proper insertion).
ALUMINUM
Fig. B
TUBE INSERT
MUST
ENGAGE
End View
Small
Aluminum Tube
TEETH
INSIDE
SMALL
End View
Small
Aluminum
Tube Insert
ALUMINUM
TUBE!
Loading...