SWiiD SWIIDCAM+ Installation And User Manual

1

SWIIDCAM+™

Z-WAVE

®

WIRELESS AUTONOMOUS PTZ IP CAMERA

Installation and User's Guide

I - FOREWORD

SwiidCam+™ is an autonomous and wireless Z-Wave® PTZ IP camera gateway, which is - as its name
implies – combines :

• A wireless IP (Wi-Fi) camera which has the following features :
(i) Pan, tilt and zoom (PTZ),
(ii) Twin lens/sensor camera : daylight and IR,
(iii) Two-way voice over IP built-in,
(iv) Local storage on SD card (card not provided),
(v) Time lapse recording,
(vi) Built in multi-level motion and sound sensors as well as sound alarm signal, and
(vii) Easy plug-and-play installation feature

• A built-in Z-Wave Plus® controller gateway enabling the user to monitor and control Z-Wave

devices such as sensors, dimmers, power meters, switches, RGBW bulbs, door locks, etc.

• A built-in rechargeable battery pack, the SwiidCam+™ is autonomous from an energy standpoint,

making it possible for the user to roam wirelessly with the SwiidCam+™ within the range of the local
Wi-Fi network

The SwiidCam+View™ application is available free on both the Apple App Store and on Google Play
respectively in iOS and Android versions. This application provides an intuitive user interface for setting
up and operating your SwiidCam+™.

Finally, the SwiidCam+™ is both Alexa- and Google Home enabled and is IFTTT compatible.

ZCAM1

EN

2

II - SPECIFICATIONS

Z-Wave® Device Type :

CENTRAL STATIC CONTROLLER

Power supply :

3.7V DC 5.8Ah Li-Ion NMC battery pack
Adapter 230VAC / 5V DC 3A

Size :

177 x 95 x 75 mm

EU Norms :

EN 61058-1 & EN 55015

IP camera .

1 mega pixels, 1280x800, 30 fps max., H.264 video compression ; automatic IR LED

PTZ features .

340° pan; 90° tilt; 3x zoom (digital)

SD card .

128 GB max.

Audio .

Built-in microphone and 0.5W speaker ; G.711 audio compression

Wi-Fi :

IEEE 802.11 ; 2.4 GHz ; supports WEP and WPA/W/WPA2 security

HA radio protocol :

Z-Wave®

HA radio frequency :

868,42 MHz (EU)

HA transmission distance :

Up to 30m indoors (depending on materials)

Working temperature :

0 – 40°C

Your SwiidCam+™ has been certified by a certification firm approved by the Z-Wave® Alliance
and, as such, is fully interoperable with all the certified Z-Wave® devices produced by other
manufacturers using the same authorised radio frequency (EU in our case).

III - KEY FEATURES

External features

Camera indicator LEDs :

• Red : Camera On

• Blue : Wi-Fi On

• Yellow : Warning and SD

card On

Side indicator LEDs :

• Left Blue/Yellow : On/Off and
battery level

• Right Green : Charging indicator

SD Card slot

Night vision IR LED

Reset button

WPS button

Camera double lens/sensor

Microphone

3

Powering up the device

Charging the device

Remove SwiidCam+™ from charging base to
access On-Off switch at the bottom of the
device. For transport and when not being used,
switch is set to Off.

When switched to On, the left LED on the plinth
of the device will either be blue to indicate
battery status OK or yellow to indicate low
battery.

If low battery, switch back to Off and place back
on charging base until right green LED on the
plinth of the device turns off and then switch
back on (left LED will then be blue).

When turning the On-Off switch to Off, the
SwiidCam+™ will lose its Wi-Fi connection and it
will may take up 30-45 seconds to reconnect the
Wi-Fi, when the switch is set back to On

Remember to plug in the wall adapter of the
charging base into the mains.

Place SwiidCam+™ on the charging base
either with the left blue LED lit (On-Off switch
to On) or OTHERWISE ONLY with the On-Off
switch to Off.

Once fully charged the right green LED will
switch off. Full recharging takes ca. 3 hours.

Once fully recharged the SwiidCam+™ can
operate away from its charging base for
around 3 hours

SwiidCam+ View™ application

SwiidCam+ View™ is a smartphone and tablet application which provides the
user interface needed for setting up and operating your SwiidCam+™. It is
intuitive and provides in-built help which makes most of the information
contained hereafter in the present Installation and User’s Guide redundant.

SwiidCam+ View™ is available free of charge both on Apple’s App Store and
on Google Play. For iOS devices, it requires iOS8 or greater and is available
in separate versions for iPhone and iPad.

On-Off
Switch

4

IV - INSTALLATION

Installation of your SwiidCam+™ is a two-step process :

• Getting your SwiidCam+™ to communicate wirelessly over your local network and with the internet;
to the SwiidCam+ View™ interface on your smartphone or tablet, and

• Setting up a network of Z-Wave® home automation devices with your SwiidCam+™ as the network’s
primary controller.

IVa - INSTALLING THE WI-FI CAMERA

1. Download and install the SwiidCam+ View™ app onto your smartphone or tablet from the Google

Play if it uses Android or from the Apple App Store in case of an iPhone or an iPad.

2. Open SwiidCam+ View™ app on your smartphone or tablet : it will show you the Home Screen

illustrated below. Tap on the big circled “+” to add your new SwiidCam+™

Home screen

Steps thereafter are also indicated on the screen of your smartphone or tablet, namely :

3. Enter the name you want to give to the location (home) where you are setting your new

SwiidCam+™ and press arrow button to continue

4. Select “Pan/Tilt camera gateway"

5. Select “Connect your camera to the Wi-Fi network”

Please make sure that your smartphone or tablet is connected to that specific Wi-Fi network to
which you want your SwiidCam+™ to belong. IMPORTANT : Make sure this is a 2.4 GHz Wi-Fi
network not a 5.0 GHz Wi-Fi network.

6. Power up SwiidCam+™ by switching on the On-Off switch at the bottom of the device and the

LED on the left side of the plinth will light up blue (provided the battery is sufficiently charged)

7. Wait until the red LED at the top of the camera starts blinking slowly, indicating the powering

up phase has been completed

8. Enter on your smartphone or tablet the password of the Wi-Fi network to which it is connected

and press “Submit”

Button to get to

information screen

Tap to add a new

SwiidCam+™

(new "home")

5

9. Press the WPS button on your SwiidCam+™ (see illustration page 2) and the 3 LEDs (red, yellow

and blue) at the top of the camera will blink in an uneven pattern

10. Press "Continue" on your smartphone or tablet until the screen shows a QR code

11. Place your smartphone or tablet 20 cm in front of the SwiidCam+™ camera lens and hold it until

the SwiidCam+™ emits a loud beep signifying that it has read the QR code and the 3 LEDs at the
top of the camera will blink in a sequential pattern

12. In due course (30-90 seconds), the yellow LED at the top of the camera will turn off and only the

blue and red LEDs will remain lit : blue for the Wi-Fi connection and red for the powered-up

status of the camera and a pop-up will say "Gateway found" and display the Camera ID number
(same as on the ID/password card provided with your SwiidCam+™)

13. Set a name for your SwiidCam+™ and tap "OK". Please note that a pre-set SwiidCam+™

password will be displayed (same as on the ID/password card provided with your SwiidCam+™)
and cannot be changed at that time (SwiidCam+™ ID/name/password are not to be confused
with the administration ID/password - see point 15 hereunder)

14. You will then be back on the Home Screen and the big circled “+” in the centre of the screen will

now show the name you have given to your SwiidCam+™

15. Tapping the big circled “+” in the centre of the and screen you will get to a pop-up request to enter

an administration ID/password for your SwiidCam+™ (in case needed, the default values of

admin / [blank]) and then the Controller Screen as pictured below will open :

Controller Screen (empty)

16. Once you press on the camera icon in the big circle you will be prompted to modify the

SwiidCam+™ password and to confirm it (in lieu of the pre-set on the ID/password card) and then
tap "OK"

17. By selecting on the Controller Screen, the camera icon in the big circle you can get to the live

video stream of your SwiidCam+™

Thereafter, whenever you want to reach the Controller Screen when turning your SwiidCam+ View™
back on (after having exited the app), tap on the appropriately named home circle which will now

6

appears on the Home Screen. Please note that you may prompted to change the administration
ID/password if you were still using the original default value of of admin / [blank].

IVb - SETTING UP THE Z-WAVE® CONTROLLER

As a certified Z-Wave® controller, your SwiidCam+™ can be used either as primary or a secondary
controller, but the current section of this Installation and User’s Guide will describe only how to use it
as a primary Z-Wave® controller. By default, your SwiidCam+™ acts as a primary Z-Wave® controller.

As a primary Z-Wave® controller, your SwiidCam+™ is able create its own network using its own
internally-generated unique identification number (known as Home ID). The following describes the
configuration steps necessary to associate your SwiidCam+™ with each of the Z-Wave® devices which
you want to include in its Z-Wave® network, whether they are to be controlled directly (e.g. actuators)
or not (e.g. sensors).

A- INCLUDING A Z-WAVE

®

DEVICE

Proceed as follows :

1. Tap on the small circle “Device #” on the left part the Controller Screen of your SwiidCam+™

(below the camera icon in the big circle) so that it lights up.

2. Then tap on the big right-hand circle with a “+” which should be entitled “Add a device” (if there

are no devices yet in your network) or on the small circled “+” in the upper right-hand corner
above the list of already included devices

3. The screen will show you a list of Z-Wave® device manufacturers in alphabetical order (after our

own Swiid™ brand). Scroll to the manufacturer of the device you want to include add, tap on it
and then on the specific device concerned

4. Your SwiidCam+™ will then beep once to indicate that it is ready to include the external device

(if nothing is done, it will time out from the inclusion mode after about 30 seconds by sounding a
double beep).

5. Put the Z-Wave® device you want to include and control in program mode (generally indicated in

a pop-up window on the screen of your smartphone or tablet - otherwise see manual of the
device).

6. The inclusion process will then start automatically : your SwiidCam+™ will sound a three-tone

chime once to indicate success and a pop-up dialog box will then ask you to assign a name to
the device you have just included. You will then automatically be able to control the device if it a
controllable one.

In the event the inclusion is not successful, your SwiidCam+™ will simply time out from the inclusion
mode after about 30 seconds by sounding a double beep.

If in Step 3 the device you wish to include is not available on the manufacturer/device list provided,
it can always be included as an “unknown” device by scrolling down to the end of the manufacturer
list to “Other Z-Wave device”. Upon inclusion, the device will however only respond to commands of
the Z-Wave Basic Command Class.

Please remember that the Z-Wave® device you want to include may have been included in another
Z-Wave® network previously and it may be necessary to reset it by running an exclusion procedure
(see below) before it can be included in your SwiidCam+™‘s network.

Upon inclusion, the devices will be placed in an “unassigned room” and can be moved to dedicated

rooms to be created by the end-user.

7

B- EXCLUDING A Z-WAVE

®

DEVICE

Exact same process as for inclusion except that :

• In Step 2, tap either the text in the upper right which reads “Remove other device” or (if there are
no devices yet in your network) or on the small circled “-” in the upper right-hand corner above the

existing device list

• In Step 7, the successful conclusion of the exclusion process (three-tone chime) will obviously
not be followed by a device naming request.

C- REMOVING/REPLACING A FAILED Z-WAVE

®

NODE

A node (device) included in its Z-Wave® network is deemed by your SwiidCam+™ to have failed if it
does not to respond to a command which has been issued or if does not report back for more than
24 hours. In that case the device will show up on your smartphone or tablet with a red “ ”. Tap on
the red “ ” to get to the Remove/Replace screen and follow on-screen instructions.

V – MANAGING THE Z-WAVE® NETWORK

A- THE CONTROLLER SCREEN (showing devices side screen)

B- ROOMS

The management of the Z-Wave® network of your SwiidCam+™ is organised in such a way as to get
the end-user to assign the various Z-Wave® devices individually to rooms that he or she will create.
Upon inclusion into the SwiidCam+™’s network, the devices will at first be placed in an “unassigned
room”.

General Z-Wave action buttons

Home sensor status

Add/delete

Z-Wave devices

Z-Wave®

devices side

screen

Back to Home Page

To video playback

To Gateway Settings

To multi-

viewing

To rooms/

scenes side

screens

To home/

away/sleep

side screen

8

To create a room, proceed as follows :

1. Tap on the small circle “Room #” on the left part the Controller Screen of your SwiidCam+™ (below
the camera icon in the big circle) so that it lights up and a scrolling list of rooms appears on the
right side of the screen (Rooms Side Screen).

2. Then tap on the small circled “+” in the upper right-hand corner above the existing room list (may
only contain “unassigned” if no room have yet been added)

3. Enter a room name of your choice and submit

You can then add devices to this room or remove them or move them to other rooms by tapping on
the room rectangle on the list of rooms (Step1 above) and then tapping on the small circle “” towards
the bottom of the right side of the screen and following the on-screen instructions.

Non-Z-Wave : When tapping on the room rectangle on the list of rooms (Step1 above), you will get

a list of all the Z-Wave® devices in the room, as well as the IP camera which has been attributed to
that room. It is possible to assign another camera to this room (provided it has been previously added
to the system) by tapping on the camera name and following the on-screen instructions.

All the rooms created (i.e. other than the “unassigned room”) can be deleted by following the same

procedure as the one described above except that one must tap the small circled “-“ instead of the
“+” and following the on-screen instructions.

Overall, your SwiidCam+™ is capable of handling up to 40 rooms and a maximum of 60 Z-Wave®
devices (in 1-40 rooms).

C- SCENES

In Z-Wave®, scenes are software routines which make it possible to send different commands to

different devices, making several different things happen at the same time or in sequence over time
or not. Such scenes are subject to trigger conditions, either voluntary like pressing on a button, or

automatic like the change of status of one or more devices and timing.
To add and programme a scene on your SwiidCam+™, proceed as follows :

1. Tap on the small circle “Scene #” on the left part the Controller Screen of your SwiidCam+™ (right

side below the camera icon in the big circle) so that it lights up. The right hand side of the screen
will change to the Scene Side Screen.

2. Then tap on the big right-hand circle with a “+” which should be entitled “Add a scene” (if this is the

first scene to be programmed) or on the small circled “+” in the upper right-hand corner above the
existing scene list, enter a scene name in the pop-up window and confirm by tapping "OK".

3. The screen will then show you an input request for the conditions (“IF” and “WHEN”) and the actions

(“THEN”). Follow the on-screen instructions to fill in the various conditions/actions instructions and
submit the scene for implementation.

IF conditions apply to the change of status of one or several Z-Wave® devices, of room conditions or
conditions reported by any IP cameras which are in the network of your SwiidCam+™. These
conditions can be alternative or cumulative : toggle by tapping on the circled “+” or “or” between
condition icons. Each scene can accept up to six IF conditions

WHEN conditions contain the time period or periods during which the scene will be active.
THEN actions can include changes to the status of one or more actionable devices, sending out of

alarm push notifications (see below), or recording of video and /or sound.

D- HOME/AWAY/SLEEP

By tapping on the small circle “Home” on the left part the Controller Screen of your SwiidCam+™
(immediately below the camera icon in the big circle), the right-hand side of the screen will change to

9

offer a choice between "Home", "Away" and "Sleep" statuses. These statuses can be used as a
WHEN condition, so as to be able to trigger several scenarios in one go from any Controller Screen.

E- ALARM (PUSH) NOTIFICATIONS FROM Z-WAVE

®

DEVICES

Through your SwiidCam+™, each of the Z-Wave® devices in your network can be programmed to
send you a push notification by e-mail in the event an alarm threshold is crossed. The end-user can
set up alarms individually on the status of each parameters of each device. For example, with a
multi-sensor you can set separate alarm thresholds for temperature (low or high), humidity,
luminosity, open/close, battery level, etc.

To add an alarm to one of your Z-Wave® devices, proceed as follows :

1. Tap on the device rectangle of the desired trigger device on any screen which contains a scrolling

list of devices

2. The device will show up with all its functions listed in separate rectangle and with a bell icon

(alarm) on the right-hand side

3. Tap on the bell icon to set alarm conditions (tailored to type of function) and follow on screen

instructions

4. Remember to tap on “Update” in the upper right-hand corner to validate and save the alarm

setting you have just created

Follow the same procedure to delete an alarm : tap on highlighted bell icon to turn it off.

Non-Z-Wave : The SwiidCam+™ has its own motion- and sound-based alarm capabilities (see

Sections VI-A and VI-B).
When any active alarm on a Z-Wave® device of the network of your SwiidCam+™ (or on the

SwiidCam+™itself) is triggered :

• It will show up automatically on the SwiidCam+ View™ screens on your smartphone or
tablet,

• It may set off a wailing sound on the in-built speaker of your SwiidCam+™, and/or

• It may send push notifications by e-mail to up to 3 e-mail addresses.

The wailing sound and the push e-mail notifications can be programmed by going into the Sensor &
Record section of the Camera Settings option page from the bottom right of the Gateway Settings

page. To access the Gateway Settings page, tap on the " " button on the top middle-right of the

Controller Screen.
Wailing sound : In Sensor & Record, tap the sub-section Speaker alarm to activate the speaker

alarm and to set the number of loops.
E-mail notifications : In Sensor & Record, tap the sub-section Email alarm and enter up to three e-

mail addresses as recipients of alarm notifications. Do not forget also to set up the SMTP server
that will be used to send the email notifications

VI - OPERATING THE SWIIDCAM+™

The SwiidCam+View™ allows you to operate (locally or remotely) side-by-side one or more wireless IP
(Wi-Fi) cameras and a network of Z-Wave® devices all from individual room screens.

10

The screen of any individual room on an iPad will show :

1. The room name with arrow to scroll to other rooms (starts with the home-named ”room", i.e. where
the images are from the base SwiidCam+™ which is the primary controller of the home’s Z-Wave®
network),

2. The video window showing the live stream from the IP camera located in that room, with above
the right-hand corner of the video window a Wi-Fi quality indicator

3. The status of sensors in the room (if there are any) : Temperature, humidity, luminosity and power
consumption

4. 4 actions buttons under the video window for all the Z-Wave® devices in the room of a specific
type : one for lights, on for all the on/off and dimmer power switches, one for curtains and other
window coverings and one for alarms

5. On the right of the screen a scrollable li st of Z-Wave® devices present in the room (but no
possibility of adding or deleting devices from this screen).

Room Screen

Additional clarifications on some the elements just described above :

Video Window : By tapping once on the video window, you get access at the bottom of the video
window to the various video functionalities described in paragraph A hereafter and, by tapping twice,
the video window can be enlarged to full screen. By moving your finger on the video window, you
can get the camera to pan and tilt, but careful of the time response lags. To zoom, widen gap
between two fingers on screen.

List of Z-Wave® devices : By tapping on the icon any of the devices you can turn on or off (open/
close) provided they are actionable devices (e.g. power switches) and by tapping elsewhere on any

Room name

Wi-Fi quality indicator

Video window

Action buttons

Room sensor

status

List of Z-Wave devices

11

of the device rectangles you can get a more complete listing of the device's functionalities (e.g.
readings from a multi-sensor). Actionable devices are recognisable by the fact their icons are in a
rectangular form, whereas the icons of non-actionable devices (e.g. sensors) are inscribed in a circle
as shown below.

Actionable Z-Wave® device

Non-actionable Z-Wave® device

A- LIVE VIDEO STREAM

The video window on the Room Screen shows the live video feed from the camera with a time/date
stamp along the top edge.

When tapping once on the screen the following video functionality icons will appear :

This icon enables you to set and go directly to up to five preset pan and tilt angles, thus
avoiding the difficult-to-predict outcome of re-orienting the camera by moving your finger
on the screen

Video recording button. If you tap on it, the central dot will turn red to indicate that your
SwiidCam+™ is recording

Tap for screenshot

Tap to get your SwiidCam+™ to sound alarm for around 10 seconds

Tap to turn on and off two-way voice over IP. Cursor will appear to allow setting of sound
volume.

Display or hide black bands on top and bottom of the video window

12

B- MANAGING THE IP CAMERA

On the Controller Screen, you will see the following icon in the top right-hand side :

Tap to go to the Gateway Settings of your SwiidCam+™ which include :

• Cam name, ID and icon

• Fixed vs. live icon

• Alarm notification

• Stream settings

• Video settings

• Camera settings

Tap on various options and follow on-screen instructions to change settings and in case of doubt
please consult http://www.swiid.com/en/ZCAM1-AS.pdf. Video password is shown as "", but
cannot be modified from this screen.

C- ADDING A COMPATIBLE IP CAMERA

To add an IP camera to the network of your SwiidCam+™, tap on the circled “Cameras #” on the left
part the Controller Screen of your SwiidCam+™ (below the camera icon in the big circle). This will
take you to the Multi-Camera Screen. Tap on the small circled “+” in the upper right-hand corner and
you will land on the same screen as in Step 4 of the installation of your SwiidCam+™ (Section IVa
hereof). Follow the steps described in Section IVa for the new camera.

Only compatible IP cameras can be installed, but they do not need to have Z-Wave® capabilities as
they would be redundant. Compatible IP cameras include those from our Taiwanese partner
StarVedia, namely the IC711, IC717, IC722, the IC731 and IC727. Only one camera per room is
allowed and only one per home can be used as a gateway (Z-Wave® primary controller).

D- ADDING OR DELETING "HOMES"

It is possible to add on your SwiidCam View+™ app additional SwiidCam+™ devices, each with its
own independent Z-Wave® network (i.e. additional homes). To do this, return to Home Screen and
tap on the circled “+” in the top right-hand corner of the screen. You will land on the same screen as
in Step 3 of the installation of your SwiidCam+™ (Section IVa hereof). Follow the steps described in
Section IVa for the new SwiidCam+™.

To delete an existing home, go to the Home Screen and simply drag and drop the circle with the
home to be deleted into the trash can icon and confirm deletion by tapping "OK" in the pop-up box.

E- PLAYING BACK RECORDED VIDEO STREAMS

On the Controller Screen, you will see the following icon in the top right-hand corner :

Tap to go to the Playback options of your SwiidCam+™ which include :

• Local

• SD card (micro)

• Time-Lapse Recording

• Dropbox

• NAS

• Event History

Follow on-screen instructions to play back video and events.

13

VII - RESETTING THE SWIIDCAM+™

A- PRESSING THE RESET BUTTON

To reset the non-Z-Wave® part of your SwiidCam+™, press for around 5 seconds the reset button on
the bottom part of the camera sphere (below the WPS button) with a paper clip or other pointed
instrument. This will reset the non-Z-Wave® part of your SwiidCam+™ to its factory settings and
terminated all Wi-Fi connections.

B- REBOOTING THE SWIIDCAM+™

To reboot the non-Z-Wave® firmware your SwiidCam+™, proceed as follows :

1. Tap on the small circle " " (Gateway Settings) on the upper right-hand side of the Controller
Screen

2. Then tap successively on ”Gateway Settings” (2nd) > ”Admin” > ”Reboot”

Careful : when pressing the reset button or when rebooting your SwiidCam+™, the Z-Wave®
settings will be preserved and may need to be reset separately as described in the next paragraph.

C- RESETTING THE Z-WAVE

®

FUNCTIONALITIES

To reset the Z-Wave® settings of your SwiidCam+™ to their original factory status, proceed as follows :

1. Tap on the small circle " " (Gateway Settings) on the upper right-hand side of the Controller
Screen

2. Then tap successively on ”Gateway Settings” (2nd) > ”Admin” > ”Z-Wave Administrator” > ”Z­Wave Reset”

Resetting the SwiidCam+™ Z-Wave® settings will result in its taking on a new randomly generated
Home ID.

Careful : This Z-Wave® resetting will result in the nodes in the network being orphaned and it will
be necessary after the reset to exclude all the nodes before re-including them in a network with a
new Home ID.

If the SwiidCam+™ is being used as a secondary controller in the network, then this reset procedure
should only be used once it has been excluded from the network, except of course if such exclusion
is not feasible (e.g. if the network’s primary controller is missing or otherwise inoperable).

Resetting the SwiidCam+™ Z-Wave® functionalities will however not delete the IP camera settings.

VIII - OTHER Z-WAVE® FEATURES

Your SwiidCam+™ offers a number of other Z-Wave® features. The main ones are described below
and additional ones can be found under http://www.swiid.com/en/ZCAM1-AS.pdf.

A- USING YOUR SWIIDCAM+

™

AS A SECONDARY CONTROLLER (Learn Mode)

Although it is intended for use as a primary Z-Wave® controller, your SwiidCam+™ can be made to
work as a secondary controller. In order to do so, the first task will be to get your SwiidCam+™
included into the network of your primary Z-Wave® controller (i.e. substituting the Home ID of the
primary controller for its own Home ID). To do this, proceed as follows:

1. Got to the Controller Screen of the SwiidCam+ View™ app onto your smartphone or tablet

2. Tap on the small circle " " (Gateway Settings) on the upper right-hand side of the screen

14

3. Then tap on successive screens ”Camera Settings”, ”Admin” > ”Z-Wave Administrator”

4. Put the primary Z-Wave controller in the inclusion mode (see user's manual of the controller)

5. Tap on "Z-Wave Learn Mode" and the inclusion process will begin by replicating node information
from the primary controller onto your SwiidCam+™

B- EXCLUDING YOUR SWIIDCAM+

™

FROM A Z-WAVE® NETWORK

Exactly the same as for the inclusion described in Section A above, except that in Step 4 the primary
Z-Wave controller must be put into in the exclusion mode.

C- ASSOCIATIONS

In Z-Wave speak, an "association " means that, within a Z-Wave® network, one node (i.e. device

aka “Source Node”) is programmed to control directly one or several nodes (“Destination Nodes”)
whenever the status of the status of the first node changes (by being triggered or operated), without
needing to pass through the Z-Wave controller.

Your SwiidCam+™ cannot create associations between other devices in its Z-Wave network, but
instead scenarios can be created to the same effect, except that these will only work if your
SwiidCam+™ is on and working correctly.

When acting as a secondary controller, your SwiidCam+™ is required - like all Z-Wave Plus devices ­to support associations on the Lifeline (Group 1) as a Source Node. Group 1 is called the Lifeline
group because important "lifeline" information about your SwiidCam+™ are sent as notifications to
that group’s Destination Nodes.

IX - OTHER SWIIDCAM+™ FEATURES

Your SwiidCam+™ offers a number of other webcam features. These include :

• Video stream settings : Bandwidth, resolution, frame rate and microphone

• Video settings : Colour, brightness, sharpness, low-light sensitivity, indoor/outdoor, image

quality, time display on image and video flip

• Night mode control : auto/manual and time schedule

• Information : includes firmware version, IP address, MAC addresses and other information

concerning the IP webcam of your SwiidCam+™

• Network . Wi-Fi network configuration (as well as wired network configuration if using LAN
connection)

• Sensor & record settings : Video recording on SD Card, NAS or Dropbox, speaker alarm
and push alarm notifications (briefly covered at the end of Section V above), time-lapse
recording parameters and camera sensor sensitivity

• Admin settings (requires administrator status by the end user) : Admin login, LED control,
date and time, firmware upgrade, reboot and Z-Wave® administration (including Z-Wave®
reset)

• Playback function : Already described in Chapter VI-E

• Chart recordings . Viewing of charts showing the values over time (per day or per month)

reported by the various Z-Wave® sensors connected to the SwiidCam+™ : temperature,
humidity, luminosity, power consumption

A description of these additional features and how to configure them can be found under

http://www.swiid.com/en/ZCAM1-AS.pdf.

15

X - WHAT IS Z-WAVE?

Z-Wave is a bidirectional radio communication protocol designed specifically for controlling, operating
and monitoring home automation equipment : lighting, heating, security, etc.

The Z-Wave protocol utilizes an optimized technology for weak bandwidth radio communications (9­100 kbps) around the 900 MHz band (868.4 MHz in Europe) and does not interfere with wireless
receivers operating in 2.4 or 5.0 GHz (Wi-Fi, Bluetooth, ZigBee®).

The range of the Z-Wave signal is approximately 50m (higher outdoors and lower indoors). However,
the Z-Wave technology automatically and dynamically creates a "mesh network" between the various
Z -Wave® devices that compose it and each of these devices becomes itself a repeater. This enables
connections between devices that are not within direct range of each other.

Each Z-Wave network has its own identifier (Home ID), which enables multiple Z-Wave networks in a
single location to operate completely independently and without interfering with each other.

The main advantage of the Z-Wave radio protocols over mesh network competitors such as ZigBee® is
the complete interoperability between the various Z-Wave devices from different manufacturers.

This interoperability is guaranteed by a specific Z-Wave certification process which is performed by
companies approved by Silicon Laboratories Inc., which itself is the owner of the Z-Wave name and
technology, and by the Z-Wave Alliance, which was created in 2005 to bring together all the
stakeholders in the Z-Wave ecosystem.

By year-end 2017, the Z-Wave Alliance has more than 700 members and more 2400 products have
been Z-Wave certified. It is estimated that, as of year-end 2017, more than 94 million devices using
the Z-Wave technology had been sold worldwide.

XI - Swiid® / CBCC DOMOTIQUE

Swiid® is a registered trademark of CBCC Domotique SAS, a French limited liability company,
incorporated in Paris under the Commerce Registry number 791 884 125 and having its registered
address at 27 avenue de l'Opéra, 75001 Paris, France

WARRANTY

CBCC Domotique SAS (as defined in the next section and hereinafter referred to as the "Supplier")

warrants to the original purchaser for a period of twelve (12) months from the date of purchase or
delivery (whichever is later) that the present device is free from material defects in materials and
workmanship and undertakes, subject to continuing availability of the device, to supply at its cost a new
device to replace any malfunctioning or otherwise defective device. In no event, shall the Supplier
refund any monies paid for the device.

Warranty claims must be filed by using the form provided on the Supplier's website
(www.swiid.com/en/contact.html) and completing it in full and sending us (against refund) the defective
device and a copy of the proof of purchase (with the date of purchase or delivery date!). Warranty
claims made more than thirty (30) days after the occurrence of the event giving rise to the warranty
claim and claims made without following the procedure set out above shall not be admissible.

The present warranty shall NOT cover, whether for damages to the device itself and for consequential
damages, faults not resulting from a material or manufacturing defect on the device, including but not
limited to:

16

• Accidents, actions of civil or military authority, civil disturbances, war, strikes, fires, floods or other
catastrophic events ;

• Installation or operation of the device other than in conformity with the present Installation and User's
Guide ;

• Devices which have been repaired or modified by any person not duly authorised to do so by the
Supplier ;

• Damages caused by (i) software utilized directly or indirectly by the device's owner or user, (ii)
computer viruses or other malware attacks or (iii) failure to implement any firmware updates supplied
without charge by the Supplier ; and

• Damages caused by power surges, by improper connection to the power grid or by using
unauthorised accessories

• The present warranty shall be governed by the laws of France.

V1.08