Swiftpoint TRACPOINT Quick Start Manual

Quick Start Guide

TRACPOINT Features

Left-click (front)

Scroll-wheel

Docking
point

Right-click (rear)

Middle finger
grip

LED

Thumb grip

Switch

USB Charger

Charging the TRACPOINT

To charge your TRACPOINT mouse:

Plug the USB charger into a USB

1.

port on your computer or into
a USB charging accessory.

Place the mouse onto the Charger.

2.

The battery LED will flash green while charging and turns off
once fully charged. The first 60 seconds of charging will give
up to one hour of use. A full charge can take up to 90
minutes, giving up to 2 weeks of use. To begin using the mouse,
move the switch on the underside to the ON position

When not using the mouse for brief periods, dock the mouse
on the USB charger so it maintains a charge.

The mouse should be fully charged periodically.

When not using the mouse for extended periods, move the
switch on the underside of the mouse to OFF

.

Connecting the TRACPOINT via Bluetooth 4.0

Once the mouse is charged, you can pair it to your
computer via Bluetooth 4.0.
Leave the mouse OFF for the first three steps.

Go to Bluetooth device menu in your system settings

1.

- Windows: Settings > Devices > Add Bluetooth device

- MacOS: System Preferences/Settings > Bluetooth

Ensure Bluetooth is switched on, on your device.

2.

3. Remove any existing “TRACPOINT” entries

in the list by selecting it, then select Remove

4.

While holding down the front button on the mouse, move the
switch on the underside of the mouse to ON. Then release
the front button as soon as the LED starts to flash orange.

Note: If you hold the front button for more than 5 seconds,
the mouse will change out of Bluetooth pairing mode,
flash green and not initiate a Bluetooth pairing process.

5.

When “TRACPOINT” appears in the list of searched
devices, click on the it to pair your mouse.

If you have a problem, switch the mouse Off then On,

6.

and try again from step 1.

If “TRACPOINT ”does not appear, make sure your system
supports Bluetooth 4 and Bluetooth is switched on.

Please note that Windows 7 does not support Bluetooth 4.0,
however you can purchase a USB Receiver which will work on
Windows 7. Accessories can be purchased from the Swiftpoint
Webpage, www.swiftpoint.com, and at other approved outlets.

Connecting to more than one Bluetooth device



TRACPOINT can store pairings with up to 3 Bluetooth
devices.
When switched on, the mouse will first try to reconnect with



the most recently used device. If this cannot be found it will
try to connect to the next device in the list.



If two or more of the TRACPOINT's current Bluetooth
connections are available nearby, you can swap between
them by holding the rear button while switching OFF
then ON again using the On/Off switch.

Configuring TRACPOINT on PC and Mac

IMPORTANT

Install the SWIFTPOINT CONTROL PANEL to configure

TRACPOINT mouse to perform exactly as you want it to.

the
Set the cursor speed, the scroll speed and direction, assign
button functionality and much more.
The driver will be updated periodically to give even more
functions later on, to make the TRACPOINT the best mousing
experience you can have.

Open browser, click in URL box and type:

1.

www.swiftpoint.com/download-tracpoint-driver

Follow the on-line instructions

2.

Using the TRACPOINT

Hold the mouse with your thumb on the thumb grip and your
middle finger on the finger grip. Rest your index finger on the
front button.

 To right-click, move your index

finger to the rear button

 Use your index finger to roll

the scroll wheel

Right click
(rear)

Left click
(front)

Tilt + Move Gestures Functions

To perform tilt gestures:

Tilt the mouse to the right
to engage the tilt gestures
and move the mouse
sideways, backwards,
or forwards.

Tilt



Move mouse forward



Move mouse backward



Swipe mouse left



Swipe mouse right

The directions may different depending on the appplication and
system setup.

- Scroll down

- Scroll up

- Left pan

- Right pan

Tilt Rear Button Gesture Functions

Zoom In

PRESS Rear ButtonTILT Mouse

Previous
Application

Zoom Out

All tilt gestures can be reassigned using the CONTROL PANEL
and assign different functions.

Next
Application

Presentation Mode

Presentation mode operates with Microsoft PowerPoint and
some other presentation applications.

Open your presentation and start the show.

Move the switch on the underside
of the mouse to PRESENT

Presentation Mode - Functions

Hold the mouse
in the palm
of your hand
and use your
thumb to operate.

Advance Slides/Left Click



Move cursor



Previous Slide



Virtual Laser Pointer




Application switcher

- Tap front buttons

- Press and hold front button

- Tap rear button

- Press and hold rear button

- Press and hold rear then
front buttons

Move the switch on the underside of the mouse to ON to
retutn to standard mouse functionality.

For more tips and videos for TRACPOINT , visit

www.swiftpoint.com/tracpoint-support

Specifications

Operating Systems

Windows 8 & 10 or higher



MacOS 10.4 or higher



Android 4.4 or higher



Communications

Bluetooth 4.0



USB Wireless (2.4GHz) , for Windows 7 PCs



(with USB Charger/Receiver purchased separately)

Power

Li-Ion Battery 3.7V, 120mAh



Charging: USB Outlet, 5V , 130mA



Install the SWIFTPOINT CONTROL PANEL at

www.swiftpoint.com/download-tracpoint-drivers

Quick Start Guide V3B En © 2018 Swiftpoint Limited. All rights reserved.