Thank you for purchasing the MCW Ramcool. This product is intended for expert users. Please consult with a
qualified technician for installation. Improper installation may result in damage to your components. Swiftech™
assumes no liability whatsoever, expressed or implied, for the use of this product, nor its installation. The
following instructions are subject to change without notice. Please visit our web site at www.swiftnets.com for
updates.
Compatibility and retention mechanism
Model 6800 to 7950 Geforce
Single adapter
Compatibility
MCW Ramcool/A All Models ( nVidia reference design)
Except
7950 GX2
7800 GS (AGP)
MCW Ramcool/79 All models (nVidia reference design)
Except
7950 GX2
7800 GS (AGP)
SLi Compatibility
All
Except
7900GT
7900 GS
None
Except
7900GT
7950GT
7900GS
Packing List
Quantity Parts Quantity Parts
1 RamCool waterblock 2 3/8” F fittings
1 Artic Cérmique™ thermal grease 2 ¼” F fittings
4 3/8” hose clamps 2 ½” F Fittings
8 ¼” hose clamps 5 Spring-loaded screws
4 ½” hose clamps 1 foot ¼” tubing
Installation Guidelines:
Step-by step
Step 1:
the RAM & carefully clean off the RAM modules with
an electronics degreaser. Apply the provided Arctic
Céramique™ compound to the RAM modules
Copyright Swiftech 2006 – All rights reserved – Last revision date: 9-30-06 – One or more Patents Pending
Rouchon Industries, Inc., dba Swiftech –3700 Industry Avenue, suite 104, Lakewood, CA 90712 – Toll free (US) 888-857-9438 – Fax 562595-8769 - E Mail: help@swiftech.com – URL: http://www.swiftech.com - Information subject to change without notice
Remove the existing cooling solution from
Step 2:
(As shown above). Turn the graphic card over keeping
in position the water block.
Then fasten the 5 screws (progressively &
alternatively).
Place the Ramcool on the RAM modules.
Step 3:
shown above. Note: the MCW Ramcool uses ¼”
tubing. Swiftech’s exclusive “F” fittings provide hi-flow
connection between it and the GPU water-block. ¼” to
3/8”, ¼” to ½” and ¼” to ¼” “F” fittings are included.
Install the tubing on both “F” fittings as
Step 4:
tubing to the barb.
Note: You can twist the “F” fittings relatively to the
tubes so as to give them a different angle/orientation in
order to route the lines as conveniently as needed.
Use the provided hose clamps to secure the
Last step:
Re-install the water-cooled VGA adapter to the
motherboard. Connect the “F” fittings to the main
cooling loop and secure the lines with the provided
hose clamps.
Always test your setup extensively for leaks
before you energize your system!
IMPORTANT DISCLOSURES
While all efforts have been made to provide the most comprehensive tutorial possible, Swiftech assumes no liability
expressed or implied for any damage(s) occurring to your components as a result of using Swiftech cooling products, either
due to mistake or omission on our part in the enclosed instructions, or due to failure or defect in the Swiftech cooling
products. WARRANTY Our products are guaranteed for 12 months from the date of delivery to the final user against
defects in materials or workmanship. During this period, they will be repaired or have parts replaced provided that: (I) the
product is returned to the agent from which it was purchased; (II) the product has been purchased by the end user and not
used for hire purposes; (III) the product has not been misused, handled carelessly, or other than in accordance with any
instructions provided with respect to its use. This guarantee does not confer rights other than those expressly set out above
and does not cover any claims for consequential loss or damage. This guarantee is offered as an extra benefit and does not
affect your statutory rights as a consumer.
Copyright Swiftech 2006 – All rights reserved – Last revision date: 9-30-06 – One or more Patents Pending
Rouchon Industries, Inc., dba Swiftech –3700 Industry Avenue, suite 104, Lakewood, CA 90712 – Toll free (US) 888-857-9438 – Fax 562595-8769 - E Mail: help@swiftech.com – URL: http://www.swiftech.com - Information subject to change without notice
Loading...