Swegon SILVER C RX 100, SILVER C CX 100, SILVER C RX 120, SILVER C CX 120 Installation Instructions Manual
Installation instructions for the
SILVER C RX/CX version F, size 100/120
GB.SILVERF120.181005
We reserve the right to alter specifications.
The document was originally written in Swedish.
www.swegon.com 1
Contents
1. Installation ............................................... 3
1.1 General .................................................................. 3
1.2 Transport within the site ......................................... 3
1.3 Parts packed together with the unit ........................ 3
1.3.1 Document pocket ............................................. 3
1.4 Arrangement ......................................................... 3
1.5 Method of delivery ................................................. 3
1.5.1 SILVER C RX ...................................................... 3
1.5.2 SILVER C CX ...................................................... 3
1.6 Lifting .................................................................... 4
1.6.1 With a fork-lift truck ......................................... 4
1.6.2 With a crane ..................................................... 4
1.6.2.1 Complete units ............................................ 4
1.6.2.2 Heat exchanger section, supplied split into two
casing sections and rotor (SILVER C RX only) ............. 5
1.7 To assemble the heat exchanger unit section, if
required (SILVER C RX only) .......................................... 7
1.7.1 Alternative 1 ..................................................... 7
1.7.2 Alternative 2 ................................................... 11
1.7.3 Common for Alternatives 1 and 2 ................... 15
1.7.3.1 To adjust the rotor’s inclination ................... 15
1.7.3.2 Sealing plates/purging sector ...................... 16
1.7.3.3 Pressing roller ............................................. 16
1.7.3.4 Vinyl-coated fabric seal .............................. 16
1.7.3.5 Sealing ....................................................... 17
1.8 Version and fan arrangement ............................... 18
1.8.1 SILVER C RX .................................................... 18
1.8.2 SILVER C CX .................................................... 18
1.9 The docking of unit sections ................................. 19
1.9.1 Fan/filter/coil heat exchanger sections
(Coil heat exchanger sections SILVER C CX only) ....... 19
1.9.2 Fastening, front/middle section ....................... 20
1.9.3 Fixation, rear of the unit .................................. 20
1.10 Duct connection ................................................. 21
1.11 Electrical Connections. ....................................... 22
1.12 Installation of pipework package
(SILVER C CX only) ...................................................... 23
GB.SILVERF120.181005
2. Dimensions ............................................23
2.1 SILVER C RX 100/120 ........................................... 23
2.2 SILVER C CX 100/120 ........................................... 24
2 www.swegon.com
We reserve the right to alter specifications.
GB.SILVERF120.181005
3440
1070
1. Installation
1.1 General
All staff concerned must acquaint themselves with these
instructions before beginning any work on the unit. Any
damages to the unit or parts of it due to improper handling or misuse by the purchaser or the fitter cannot be
considered subject to guarantee if these instructions have
not been followed correctly.
The product identification label is affixed on the inspection
side of the air handling unit. Refer to the particulars on the
product identification plate when you contact Swegon.
The air handling unit is supplied in packaged condition.
Possible ordered accessories are supplied in separate packaging with the unit.
1.2 Transport within the site
Before removing the transport pallet/transport cradle, if
used, determine whether a forklift truck or a pallet transporter will be used for further transporting the unit within
the site to the spot where it will be installed.
1.3 Parts packed together with the unit
Components such as the commissioning plates, bolts and
document pocket are supplied in separate packaging and
delivered together with the air handling unit.
1.5 Method of delivery
1.5.1 SILVER C RX
The SILVER C RX 120 is normally supplied in five separate
sections: Two fan sections, two filter sections and one
heat exchanger section.
The heat exchanger section can also be supplied split into
two casing sections and rotor, in which case the rotor is
supplied tilted in a transport cradle (transport height =
2,930 mm, minimum transport width = 2,350 mm). See
Section 1.7 for installation particulars.
For other dimensions and weights, see Section 2.1.
Heat exchanger section supplied as a separate unit
3440
1070
1.3.1 Document pocket
Secure the document pocket to the exterior of the air
handling unit or another appropriate place.
1.4 Arrangement
The air handling unit must be mounted horizontally on a
flat and firm supporting surface and this surface must be
constructed in a way enabling it to support the weight of
the unit.
When installing the air handling unit and connecting pipework and electric cables, make sure that adequate free
space is provided for opening the inspection doors and
covers and withdrawing functional sections, such as filter
cassettes and fan assemblies, clear of the unit casing.
Inspection space required
A clear space of 1,000 mm should be provided in front of
the unit for opening the inspection doors.
Heat exchanger section, supplied split into two casing sections and rotor
Rotor, Ø 3150
2930
1070
1868
1170 2350
1861
Transport cradle
1.5.2 SILVER C CX
The SILVER C CX 120 is supplied in six separate sections:
Two fan sections, two filter sections and two coil heat
exchanger sections.
For dimensions and weights, see Section 2.2.
We reserve the right to alter specifications.
www.swegon.com 3
1.6 Lifting
1.6.1 With a fork-lift truck
GB.SILVERF120.181005
NOTE! High centre of
gravity!
1.6.2 With a crane
1.6.2.1 Complete units
Rotary heat exchanger (SILVER C RX only).
L
L
NOTE! Make sure that
forks of the fork-lift truck
are sufficiently long!
Other sections
L
L
NOTE! Make sure that
forks of the fork-lift truck
are sufficiently long!
NOTE! A line spreader must
be used!
NOTE! High centre of
gravity!
Rotary heat exchanger (SILVER C RX only).
4 www.swegon.com
NOTE! A line spreader must
be used!
Other sections
We reserve the right to alter specifications.
GB.SILVERF120.181005
1.6.2.2 Heat exchanger section, supplied split into two casing sections and rotor (SILVER C RX only)
NOTE! A line spreader must
be used!
Lower casing section
Upper casing section
We reserve the right to alter specifications.
www.swegon.com 5
Rotor
GB.SILVERF120.181005
Remove the
wooden stud
Remove the anchor
plate
Guard plate
6 www.swegon.com
NOTE! Carefully raise the rotor so that it
will not be damaged! Make sure that the
lifting device rests against the protecting
plate at the top edge.
We reserve the right to alter specifications.
1.7 To assemble the heat exchanger unit
section, if required (SILVER C RX only)
If the heat exchanger unit section is supplied in parts, they
must be jointed together. This can be done in two ways:
Alternative 1 is appropriate for use if there is sufficient free
space upward since this alternative is simpler. If sufficient
space is not available, Alternative 2 should be used.
If the heat exchanger unit section is supplied as one unit,
go on to Section 1.8.
1.7.1 Alternative 1
GB.SILVERF120.181005
Remove the upper shaft bracket
and the sealing plate (2x)
Shaft
mounting
brackets
We reserve the right to alter specifications.
Lower casing section
www.swegon.com 7
Lift the rotor into the lower casing section (see Section 1.6).
NOTE! IMPORTANT! The smooth side of the rotor hub (without holes) should face the pressing roller!
Be careful not to damage the rotor!
Hub side
GB.SILVERF120.181005
Pressing roller
8 www.swegon.com
Mount the upper shaft bracket
and the sealing plate (2x)
We reserve the right to alter specifications.
Loading...