
TECHNICAL INFORMATION
SOLID SURFACE PRODUCTS SPECIFICATION AND TECHNICAL DATA SHEET
Product
Swanstone Reinforced Solid
Surface Products
Manufacturer
Swan, St. Louis, Missouri with
manufacturing facilities in
Centralia, Illinois.
Product Composition
Swanstone® is a compressionmolded compound that
consists of a blend of polymer
resins, fillers and reinforcement
additives. In the manufacturing
process, Swanstone transforms
into a thermoset material that
has extreme resistance to
heat, impact, expansion, and
chemicals.
Product Category
Swanstone is available in
integral top and bowl vanity tops, bathtub surrounds,
shower walls, kitchen sinks,
kitchen countertops, undermount sinks, bar sinks, drop-in
lavatories, undermount bowls,
blank vanity tops and table
tops. Offset vanity top bowl
locations are available.
Colors
Swanstone is available
in a variety of solid and
aggregate colors, including
four eco-friendly colors.
Warranties
Swanstone wall panels and
trim kits, vanity tops and
bowls, drop-in kitchen and
bar sinks, window trim kits
and shower floors are covered
by a limited lifetime warranty
for residential applications.
For commercial applications
Swan offers the following
limited warranties:
25-Year Limited Warranty
on wall panels and trim kits.
25-Year Limited Warranty
against thermal cracking on
our vanity tops and bowls.
10-Year Limited Warranty
against defects on
counter-tops.
10-Year Limited Warranty
against defects and/or
thermal cracking on our
kitchen sinks and bar sinks.
10-Year Limited Warranty
against warping, blistering,
loss of color, or fading on
shower floors. Complete
details and product warranty
application for both residential and commercial are
available by writing to Swan.
Maintenance
Swanstone should be cleaned
as you would any other
fine kitchen or bath fixture.
For kitchen sinks and countertops, rinse any food or
beverage residue as soon
as possible; follow up with
normal household cleaners.
To remove residue that cannot
be rinsed away or removed
with other types of cleaners,
use powdered abrasive cleaners and/or a nylon or plastic
scrubbing pad. Vanity tops
should be cleaned with normal
household cleaners. Cleaners
designed for removing mineralbased stains can be used on
Swanstone, as well as a mild
solution (50/50) of chlorine
bleach and water. In the
event of a scratch, start with
powdered abrasive cleaner
and a scrubbing pad; if further
attention is needed, use white
automotive rubbing compound
or light sanding with a 400
grit or 40 micron sandpaper.
Application
Any interior, horizontal and
vertical surface application.
Also, available for kitchen sink,
shower floor, lavatory bowl
Availability
Swanstone is available nationwide through local stocking
distributors. Contact Swan for
your nearest distributor.
and bar sink applications.
Cost
Limitations
Swanstone Products are not
recommended for exterior
Cost varies with product
category. Contact your local
distributor for applicable costs.
use. Material should not be
used in areas exposed to
sustained temperatures exceeding 450 degrees F. Follow
all recommended installation procedures provided by
manufacturer.
Installation
Swanstone reinforced solid
surface products are shipped
with complete installation
manuals provided with every
unit. Consult the specific
product installation manual
Finish
The decorative surface of
Swanstone is a matte finish
equal to a 320 grit sandpaper
for step-by-step installation
procedures. All manuals are
available through Swan or
your local distributor.
(gloss reading of 25). A higher
sheen can be produced by
buffing the product with commercial rubbing compound.
Chemical And Stain Resistance
Chemical and Stain Resistance–NEMA LD3-3.09 No lasting effect
on Swanstone occurred from the exposure to the following.
Class I Chemicals
Solvents
Acetone
Amyl Acetate
Benzene
Carbon Tetrachloride
Ethyl Ether
Gasoline/Kerosene
Ethanol
Methanol
Toluene
Chloroform
Ethyl Acetate
Naphtha
Other
Ammonia (10%)
Iodine
Lye (1%)
Mercurochrome
Nail Polish Remover
Potassium Permanganate
Silver Nitrate (10%)
Sodium Bisulfate
Sodium Hypochlorite (5%)
Trisodium Phosphate
Urea (6%)
Vinegar
Class II Chemicals
Acids
Furfural
Methylene Chloride
Nitric Acid (30%, 70%)*
Phenol
Acids (99.5%)
Citric
Hydrochloric (20%)
Phosphoric
Sulfuric (77.96%)*
Trichlor Acetic
Formic
Hydrogen Peroxide
Alkalies
Ammonium Hydroxide
Sodium Hydroxide
(10% & 40%)
Sodium Hydroxide Flake
*May cause slight lightening.
Swan • St. Louis, MO 63101 • (800)325-7008 • swanstone.com 177
GUIDES, COLORS AND INDEX

SOLID SURFACE PRODUCTS SPECIFICATION AND TECHNICAL DATA SHEET
SOLID SURFACE PRODUCTS
SPECIFICATION AND TECHNICAL DATA
PROPERTY TYPICAL RESULTS
TEST
Impact Resistance No damage 1-1/2 Diameter Steel Ball. Over 72” NEMA LD-3
Izod Impact
Method A (with notch) 3.0 ft. - lb./in. ASTM D256
Method E (reverse notch) 4.0 ft. - lb./in.
Stain Resistance Passes
Cigarette Resistance Passes
Boiling Water Resistance No effect NEMA LD-3
High Temperature Resistance Slight effect NEMA LD-3
Abrasion Resistance Passes ASTM D4060
Color Fastness and Aging No change NEMA LD-3
Tensile Strength 4439 PSI ASTM D638
Tensile Modulus 7.48 x 10
Tensile Elongation .45% ASTM D638
Hardness Barcol Hardness: 51 ASTM D2583
Slip Resistance
Fungus Resistance
Bacterial Resistance
Wear and Cleanability
Flexural Strength
Flexural Modulus
Thermal Expansion
Gloss (60°)
Water Absorption
Specific Gravity
Rockwell RB Hardness: 60.5
15-T Hardness: 34.7
Passes ASTM F462
Passes: 0 Growth ASTM G21-96
Passes: 0 Growth ASTM G22-90
Passes
8225 PSI ASTM D790
7.49 x 10
1.98 x 10
40
.321% ASTM D570
1.55
TECHNICAL INFORMATION
ASTM D256
CSA B45.5/IAPMO Z124-2011
CSA B45.5/IAPMO Z124-2011
5
PSI ASTM D638
CSA B45.5/IAPMO Z124-2011
5
PSI ASTM D790
-4
in/in/°F ASTM D696
NEMA LD3
FLAMMABILITY
Flame Spread Index Meets Class A ASTM E84
Smoke Developed Index 85
Fire Rating Class A
ASTM E84
Approximate weight per square foot 2 lbs. for 1/4” sheet. See product guide for actual weights.
RATINGS AND LISTINGS
American National Standard
Institute-ANSI Z124.3 and Z124.6
National Plumbing Code of Canada
CSA 1345 Series
Swanstone
51 Certified for Both Food and
Splash Zone Applications
International Association of
Plumbing and Mechanical Officials
(IAPMO)-listed
Technical Services
Please call (800) 325-7008 or email us at infomail@swanstone.com. Visit our website www.swanstone.com for details including dimensional autocad drawings.
New York City Material Acceptance
Application #298-88-M
Housing and Urban Development
-HUD UM 73 Certified
Swan • St. Louis, MO 63101 • (800)325-7008 • swanstone.com178
®
is NSF Standard