Swanstone MF-1W Installation

Laundr y Tubs

MMFF-11FF
((SSiinnggllee BBoowwll,, FFlloooorr MMoouunntt MMeettaall LLeeggss))

MMFF-11PPFF
((SSiinnggllee BBoowwll,, FFlloooorr MMoouunntt PPlla

assttiicc LLeeggss))

MMFF-11WW ((SSiinnggllee BBoowwll,, WWaallll MMoouunntt))
MMFF-22FF

((DDoouubbllee BBoowwll,, FFlloooorr MMoouunntt MMeettaal

l LLeeggss))

MMFF-22WW ((DDoouubbllee BBoowwll,, WWaallll MMoouunntt))

 Product Warnings
 Safety Guidelines
 General Information
 Installation Procedure
 Cleaning & Maintenance
 Warranty Infor mation

Register your warranty at www.swanstone.com.

Read and Understand

Before Installing

Form # 513-1

800-325-7008 3 The Swan Corporation – Swanstone

The Swan Assurance — if our product is properly

installed and maintained, as stated in these

instructions, it will not leak.

RReemmeemmbbeerr

––

SSaaffeettyy

FFiirrsst

t

The Swan Corporation, the makers of the Swan products,
cannot anticipate every possible circumstance that might
involve a potential hazard during the installation of our
product(s). The warnings and instructions in this
installation guide are, therefore, not all-inclusive. If a tool,
installation procedure, or work method that is not
specifically recommended by The Swan Corporation is
used, you must satisfy yourself that it is safe. You should
also make sure that the Swan product(s) will not be
damaged by the methods you choose. The Swan
Corporation will not be held responsible for water damage
of any kind in connection with the installation of one of
our Swan bath/shower/panel kits.

To avoid product damage, personal injury, or even possible
death, carefully read, understand, and follow all the
instructions in this installation guide before installing this
product(s). Do not use cleaning fluids or operate power
tools unless you read and understand the instructions and
warnings in this and all other applicable labels or manuals.
Proper use of tools and the products described in this
guide is your responsibility.

WARRANTY

This product is covered by a Limited Lifetime Warranty.
Refer to the Warranty section in this manual for complete
details.

SSaavvee tthhiiss mmaannuuaall ffoorr ffuuttuurree rreeffeerreennccee..

Important information on cleaning and maintenance is
contained within.

WARNING

IMPORTANT NOTICE

IMPORTANT NOTICE: Indicates that equipment or
property damage can result if instructions are not
followed.

Read and Understand the Manual

It is the responsibility of any individual who
installs or maintains this product to fully

understand and follow proper installation and
maintenance procedures. Be aware of the inherent
dangers in the use of power tools when installing this
product. Read and understand all Warnings, Cautions,
and Important Notices in this manual.

Work Safely

DO NOT proceed if any doubt arises about the

correct or safe method of performing anything

found in this or other Swan manuals. The
installation of this product can require using power tools.
Do not use power tools without adequate training. If
necessary, hire or consult a trained professional for
expert assistance before continuing.

Use Proper Tools

Always use proper tools which are in good,

working condition during the installation of the

Swan products. Using tools other than those
listed could adversely affect the integrity of floors, pipes,
walls, or this product and could result in water damage,
or other damage to floors, pipes, walls, or other portions
of your building or home.

Inspect Before Cutting

Make sure no electrical wiring or plumbing is

present before cutting into a wall.

CAUTION: Indicates a potentially hazardous
situation which, if not avoided, may result in minor or
moderate injury. It may also be used to alert against
unsafe practices.

Lifting Hazard

According to the National Institute for
Occupational Safety and Health, the

recommended maximum safe lifting weight is
51 pounds, with all lifting conditions perfect—minimal
forward reach, steady load close to the body, straight
back, load between knees and shoulders, and good
grips. To avoid personal injury, always use these proper
lifting techniques and use two people to move heavy
cartons. Use appropriate lifting devices to move the
load. Always use two people when lifting heavy or bulky
cartons. DO NOT attempt to lift objects that are too
heavy.

WHEN CARRYING A HEAVY LOAD—GET HELP!

Slipping Hazard

Do not install this product in the presence of
water. Installing this product without drying all

surfaces, or in the presence of water, could
cause you to slip and fall due to wet floors or spilled
fluids. Personal injury can result from slips or falls.
Before installation, dry all surfaces, including the floor,
with a cloth or paper towel. Clean up all water or spilled
fluids immediately.

Tripping Hazard

Personal injury can result from tripping over
power cords, tools, or other items. DO NOT
leave items laying around the work area.

Personal Protection

Be sure to use all personal
protective equipment, such as sturdy

work boots, preferably with steel
toes, gloves, and hard hat, if necessary, to ensure your
own safety. To prevent possible damage to your
hearing, always wear ear protection, such as earmuffs or
earplugs, when working around power tools.

Cutting Hazard

The installation of the Swan product may
require using power tools. Keep hands away

from the cutting edge of any tool used in the
installation of our product. Placing fingers in or around
the cutting blades could result in serious personal injury.

CAUTION

IMPORTANT NOTICE

The Swan Corporation – Swanstone 4 800-325-7008

Safety Guidelines

WARNING: Indicates a potentially hazardous
situation which, if not avoided, could result in serious
injury or death.

Eye Protection

Be sure to use all personal protective
equipment to ensure your own safety. To

avoid eye injury, always wear protective
glasses with side shields when using power tools. Also,
make sure no one else can be injured by flying particles
when using power tools.

Fire Hazard

Personal injury or death can
result from a fire caused by

flammable liquids or
silicone. Cleaners or solvents can be highly explosive,
resulting in personal injury or even death, when not used
properly. Clean up any flammable substance
immediately. Sparks or open flames can cause
flammable substances to ignite. DO NOT smoke while
working on or near any flammable substance.

Solvents Hazard

Follow all manufacturer’s safety instructions
for silicone and denatured alcohol. Alcohol

vapors are both flammable and hazardous to
breathe. Silicone vapors may irritate eyes and nose.
Personal injury can result from improperly handling or
use of products such as denatured alcohol. Always
follow the manufacturer’s recommendations for the safe
use of these products. Ventilate any work area before
beginning to apply silicone, cleaning agents, or solvents.

Fumes Hazard

The fumes from the silicone and
solvents used by the installer can be
harmful if used in an unventilated

room. Always work in a well-ventilated area.

Power Tool Hazard

To prevent personal injury or possible
death, always follow the electrical

safety recommendations of the
power tool’s manufacturer. Do not use power tools in an
unsafe manner. Power tools should only be connected
to a circuit protected by a ground-fault circuit interrupter
(GFI).

Shock Hazard

Never use electric power tools
around water, condensation, or other

liquids. Electric shock can cause
severe burns, significant injuries, and even death. If an
extension cord is required, always use an OSHA
approved extension cord. Power cords should only be
connected to a circuit protected by a ground-fault circuit
interrupter (GFI).

Electrical Shock Hazard

Contacting live electrical wiring with

power tools or hand tools can cause

serious injury or death. Make sure
all related circuit breakers are turned OFF. Test for live
circuits or wiring inside any wall where installation of the
Swan product requires cutting into a wall.

Electrocution Hazard

Water and other liquids conduct

electric current and can create a

short circuit, resulting in injury or
death. Keep all liquids away from electrical cords and
power tools. DO NOT create a short circuit between a
source of electricity and a liquid by being in contact with
both simultaneously.

WARNING

800-325-7008 5 The Swan Corporation – Swanstone

Safety Guidelines

General Information

A laundry tub or utility sink can be a useful addition to
any home to soak dirty clothes, wash the dog, or clean
large, odd-shaped household goods. Our laundry tubs
are made from Veritek, which makes them easy to install
and maintain. Our Veritek material has no surface
coating to chip or crack and will not mold or mildew.
The laundry tubs can also be secured to the wall or the
floor as a precaution to prevent unwanted tipping.

The installation process is straightforward and most
homeowners can easily complete the task. The hardest
part of the job, if necessary, may be installing the water
lines and drain pipe. Always check local building codes
to verify that you, the homeowner, can install the
plumbing yourself.

A laundry tub is an easy project to install and requires
very few special tools. Followed carefully, these
installation instructions will result in an easy, trouble-free
installation of your Swan Corporation product. Any
deviations, additions, and/or deletions from the
prescribed installation, without prior written approval of
our Customer Relations Department, will void the
warranty covering this product. Not following the
directions could also result in personal injuries, water
damage, and other damage to floors, pipes, walls, and
other portions of your building or home.

•• RReeaadd aallll iinnssttrruuccttiioonnss ccoommpplleetteellyy bbeeffoorree
bbeeggiinnnniinngg iinnssttaallllaattiioonn..

•• CChheecckk aallll lloocca

all pplluummbbiinngg ccooddeess..

•• BBee ssuurree ttoo sshhuutt ooffff tthhee wwaatteerr aatt tthhee
ssoouurrccee bbeeffoorree sstta

arrttiinngg iinnssttaallllaattiioonn..

CCoonntteennttss ((FFlloooorr MMoouunntt UUnniittss))

 Laundry Tub
 Four Metal Angular Legs
 Leveling Brackets (Qty 4)
 Flat Head Screws (Qty 4)
 Nuts (Qty 4)

CCoonntteennttss ((WWaallll MMoouunntt UUnniittss))

 Laundry Tub
 Filler Brackets (Right and Left)
 Filler Bracket Mounting Screw (Qty 2)
 Wall Mounting Plate
 Screws for Wall Mounting Plate (Qty 3 or 6)
 Wall Anchors for Wall Mounting Plate (Qty 3 or 6)

PPuurrcchhaasseedd IItteemmss

 Faucet
 Flexible Hot and Cold Water Supply Lines
 PVC Trap Kit
 PVC Tailpiece
 1/4” x 1-1/2” Tapcon Screws (optional for wall mount

units only - for concrete wall installation)

 Floor Anchors and Bolts (optional)

RReeqquuiirreedd TToooollss aanndd SSaaffeettyy EEqquuiippmmeenntt

 Safety Glasses
 Hearing Protection
 Hammer
 Adjustable Pliers
 Adjustable Wrench
 Phillips Screwdriver
 Flat Blade Screwdriver
 Tape Measure
 Hacksaw (Cutting tail piece to length)
 Level
 Hammer Drill and Carbide Drill Bit (for wall mount

installation into concrete or to fasten the legs to the
floor)

LT-032

LT-031

The Swan Corporation – Swanstone 6 800-325-7008

General Information

UUnnppaacckkaaggiinngg

 Use care when opening the box so that you do not

damage the product.

 This product is shipped to you or your retail center

after careful inspection. After purchasing the product,
carefully unbox and inspect the product for any
shipping damage that may have occurred. If damage
is found, report it immediately to the store of
purchase. Installation of a damaged product will void
the warranty.

 Make sure the product is the correct size and confirm

that all parts have been included before beginning
installation.

 Floor mount models are shipped with four legs and

leveling hardware. The floor mount models DO NOT
have right and left side filler brackets like the wall
mount models.

 Please use the model number located on the side of

the box when contacting us with questions
concerning the installation of this product.

HHeellppffuull HHiinnttss

 Read all instructions carefully BEFORE starting the

installation. Familiarize yourself with the various
parts of the kit.

 Store unused materials away from the work area to

prevent accidental damage.

 If the product is placed over a garage or on an

outside wall, care must be taken to ensure that the
shower plumbing is properly insulated from cold
temperatures.

DDiissccllaaiimmeerr

 The information contained in this Installation

Instruction is given free of charge. It is based upon
technical data which we believe to be reliable and is
intended for use, by persons having knowledge of
this technical area, at their own discretion and risk.
The Swan Corporation assumes no responsibility for
results obtained or damage incurred from the use of
this material either in whole or in part by the buyer.

 This manual will give you basic step-by-step

instructions for the installation of the product that will
work in most types of installations. If you have an
installation application that is not covered in this
manual, before beginning the installation, please
call your local Swan distributor or contact the Swan
Corporation directly for additional information about
your application.

 Follow all installation instructions. Failure to follow

these instructions could result in personal injuries,
water damage, or other damage to floors, pipes,
walls, or other portions of your building or home.

800-325-7008 7 The Swan Corporation – Swanstone

General Information

QQuuiicckk RReeffeerreennccee AAsssseemmbbllyy

1. Prior to installation of the laundry tub, first attach the

legs to floor mount models (Step 1a) or attach the
filler brackets to the wall mount models (Step 1b).
Refer to the specific section in this manual for
detailed instructions.

2. Attach the wall mounting plate to the wall. (Step 2a,

2b, or 2c).

3. Finally, install faucet and P-trap onto the laundry tub.

4. Install laundry tub.

5. Anchor floor mount units to the floor (optional).

6. Install splash guard (optional).

1. Attach Legs / Filler Brackets

11aa.. AAttttaacchh MMeettaall LLeeggss —— MMFF-11FF aanndd

MMFF-22FF ((SSiinnggllee aanndd DDoouubbllee BBoowwll
MMooddeellss))

1. Place the laundry tub upside down on a flat surface.

Protect the top edges of the laundry tub from
scratches or other damage by placing cardboard or
other scratch resistant material on the floor.

2. Slide the metal leg into one of the plastic corner
retaining sockets in the bottom of the laundry tub.
All four legs are identical and can be installed in any
one of the four corners.

3. Place a block of scrap wood over the end of the leg
and drive the leg down into the socket with a
hammer.

4. Install the other three legs in the same manner.

LT-003

LT-002

LT-001

The Swan Corporation – Swanstone 8 800-325-7008

General Information Installation Procedure

5. Install one leg leveler on each leg using the screw
and nut included with each unit. Do not completely
tighten the screws until the laundry tub is in its final
location and can be leveled.

1b. Attach Filler Brackets and Wall Mount —

MF-11W and MF-22W (Single and Double
Bowl Mode

ls)

1. Place the laundry tub upside down on a flat surface.
Protect the top edges of the laundry tub from
scratches or other damage by placing cardboard or
other scratch resistant material on the floor.

2. Find the right-side filler bracket. Install it with the
end of the filler bracket fitted between the outside of
the sink and guide posts (1). Also place the filler
bracket over guide post (2) and the screw hole in
the bottom of the laundry tub.

3. Using a flat blade screwdriver, install one panhead
screw to hold the filler bracket in place. Do not
overtighten the screw.

4. Install the left-side filler bracket in the same manner.

LT-020

LT-019

2

1

LT-018

LT-004

SCREW

LEG LEVELER

NUT

800-325-7008 9 The Swan Corporation – Swanstone

Installation Procedure

2. Attach Wall Mounting Plate

22aa.. AAttttaacchh WWaallll MMoouunnttiinngg PPllaattee ttoo FFrraammeedd

WWaallllss

1. Locate the rough position of the laundry tub and
then locate the wall studs. The mounting plate must
be attached using at least three screws.

If only two screws can be used, install cross blocking
(2” x 6”) between the studs and then attach the wall
mounting plate. Again, for double sinks install cross
blocking (2” x 6”) between the studs to add extra support
for the wall mounting plate and the sink.

2. Determine the comfortable working height of the top
of the sink. This height may vary depending on your
application; however, a typical dimension is 32” up
from the floor. Use a level to mark a line 1” below
the desired height on the wall.

Note: Trial fit the wall mounting plate to the laundry tub.

If the mounting plate is too long, break off the left
side of the wall mounting plate by snapping it
along the plate’s scored ridge.

LT-024

LT-023

31”

LT-022

LT-021

The Swan Corporation – Swanstone 10 800-325-7008

Installation Procedure

3. Position the top lip of the wall mounting plate on the
mark. Be sure you mark the mounting holes over
the studs/cross-blocks. Use a bubble level to make
sure the wall mounting bracket is level.

4. Drill a 1/8” pilot hole into the wood and attach the
mounting plate to the wall with at least three 1/4" x
1-1/2" long zinc hex head lag screws. Tighten the
screws with a Phillips screwdriver.

Note: On double bowl models use at least six screws to

attach the wall mounting bracket to the wall.

22bb.. AAttttaacchhiinngg WWaallll MMoouunnttiinngg PPllaattee ttoo

CCoonnccrreettee oorr BBlloocckk WWaallllss wwiitthh PPllaassttiicc
WWaallll

AAnncchhoorrss

There are two methods to install the mounting plate onto
a concrete or block wall; Step 2b) a plastic wall anchor
with a lag screw, or, Step 2c) Tapcon concrete screws.
The tapcon screws for mounting the wall mounting plate
to concrete are not supplied with the product and must
be purchased separately.

1. Locate the height of the wall mounting plate in the
same manner as with wood construction (Step 2a).

Note: Trial fit the wall mounting plate to the laundry tub.

If the wall mounting plate is too long, break off
the left side of the wall mounting plate by
snapping it along the plate’s scored ridge.

Oversized pilot holes may make it impossible to properly
set the anchor and will reduce the anchor's load (holding)
capacity. This reduced holding capacity can result in the
anchor pulling free from the wall, resulting in possible
personal injury or even death.

2. Drill a 5/16” pilot hole two inches into the concrete or
block wall using a masonry bit and a hammer drill.
Clean out the hole with a vacuum sweeper.

Note: In concrete block walls do not drill the anchor

holes into the mortar joints. These joints typically
do not have the same holding strength as the
block itself.

LT-026

2”

WARNING

LT-024

LT-025

800-325-7008 11 The Swan Corporation – Swanstone

Installation Procedure

3. Insert the plastic anchor into the hole and drive it in
until it is flush with the wall surface. For single bowl
models use at least three anchors. For double bowl
models use at least six anchors.

4. Attach the mounting plate to the wall with 1/4" x
1-1/2" long Phillips head screws (supplied with unit).
For single bowl models use at least three screws.
For double bowl models use at least six screws.

Note: Make sure the wall mounting plate is straight,

regardless of the wall contour, before completely
tightening the screws. If the wall is not flat, shim
behind the mounting plate, as needed.

22cc.. AAttttaacchhiinngg WWaallll MMoouunnttiinngg PPllaattee ttoo

CCoonnccrreettee oorr BBlloocckk WWaallllss wwiitthh TTaappccoonn
WWaallll A

Anncchhoorrss ((UUsseerr SSuupppplliieedd))

1. Locate the wall mounting plate in the same manner
as with wood construction.

Note: Trial fit the wall mounting plate to the laundry tub.

If the wall plate is too long, break off the left side
of the wall mounting plate by snapping it along
the plate’s scored ridge.

Oversized holes may make it impossible to properly hold
the Tapcon screw and will reduce the load (holding)
capacity. This reduced holding capacity can result in the
screw pulling free from the wall, resulting in possible
personal injury or even death.

2. Drill a 3/16" pilot hole into the wall using a masonry
bit and hammer drill.

Note: Always follow the mounting hardware

manufacturer’s recommendation for installation of
their mounting hardware.

WARNING

LT-024

LT-028

LT-027

The Swan Corporation – Swanstone 12 800-325-7008

Installation Procedure

3. Attach the mounting plate to the wall with 1/4" x
1-1/2" long Tapcon Hex Head Masonry Screws. Do
not overtighten the screws. For single bowl models
use at least three screws. For double bowl models
use at least six screws.

Note: Make sure the wall mounting plate is straight,

regardless of the wall contour, before completely
tightening the screws. If wall is not flat, shim
behind the mounting plate, as needed.

33.. IInnssttaalllliinngg tthhee FFaauucceett aanndd DDrraaiinn

1. Shut off the water supply to the entire house or at
the location of the old sink.

2. Release the pressure and drain the water lines by
turning on a faucet in the lowest part of the house.
Turn on both the hot and cold water faucets.

3. If replacing an existing laundry tub, loosen and
remove the hot and cold water lines and waste pipe
connections. Use a container to catch any water
remaining in the P-trap.

Note: If the P-trap and water lines are in poor condition,

replace them with new parts. Also replace any
rusted or corroded fittings with new parts. The
faucet can be reused and reinstalled.

4. Install the faucet assembly according to the
manufacturer’s instructions (homeowner supplied).

Note: Preinstallation of the faucet, supply lines, and

P-trap are easier when the laundry tub is not
against and/or attached to the wall.

5. Attach the two flexible water lines onto the faucet
(homeowner supplied). Do not over-tighten the
connections.

LT-006

LT-029

800-325-7008 13 The Swan Corporation – Swanstone

Installation Procedure

LT-007

6. Assemble the PVC trap components (homeowner
supplied) and attach them to the drain hole(s) in the
laundry tub.

44.. FFiinnaall IInnssttaallllaattiioonn

1. For models with legs, place the laundry tub where it
will be installed. For wall mount models, hang the
sink onto the wall mounting plate (see Step 2).

2. On wall mount models only, lift and place the sink over
the wall mounting plate. Make sure the laundry tub is
seated securely into the lip of the wall mounting plate.

LT-030

LT-009

LT-008b

LT-008

The Swan Corporation – Swanstone 14 800-325-7008

Installation Procedure

3. Attach the PVC tailpiece (homeowner supplied) to
the drain pipe. Cut the tailpiece to the proper length
using a hacksaw, if necessary. Use sandpaper or a
file to remove any burrs or sharp edges.

4. Attach the flexible water supply lines to the water
shut off valves. The threaded ends of the water lines
can be wrapped with Teflon pipe tape to ensure a
tight, leak-proof seal. Tighten the fitting with a
wrench but do not over-tighten.

5. The water lines and waste pipes should now be
completely installed.

6. Slowly turn ON the hot and cold water shut off
valves. Turn the faucets ON and flush the water
lines to remove any debris that may be in the water
line or the drain pipe.

LT-013

LT-011

800-325-7008 15 The Swan Corporation – Swanstone

Installation Procedure

LT-010

LT-012

7. Check all water lines and waste connections for
leaks. Tighten the connection if a leak appears. Do
not over-tighten.

55.. FFlloooorr AAnncchhoorrss

A laundry tub(s) that is full of water can weigh from 175 to
350 pounds and could tip over if someone pulls against it,
causing personal injuries, death, and/or damage to your
home. Securing the legs to the floor will help prevent
unwanted tipping.

1. As added protection against unwanted tipping of
floor model laundry tubs, secure the unit to the floor
using homeowner supplied anchors.

2. Adjust the four leveling feet on the legs. Aslight
angle (front to back) toward the drain will eliminate
water from standing in the bottom of the laundry tub.

66.. SSppllaasshh GGuuaarrdd

As an added precaution to water splatter and/or damage
to the wall behind the sink, you can install a piece of 1/8”
plastic onto the wall. You can also caulk the area where
the plastic meets the edge of the laundry tub.

LT-016

LT-017
LT-015

WARNING

LT-014

Installation Procedure

The Swan Corporation – Swanstone 16 800-325-7008

CCaarree aanndd CClleeaanniinngg

Swan products are stain and wear resistant; however,
the finish requires reasonable care.

MMaaiinntteennaannccee AAnndd CClleeaanniinngg

Everyday cleaning with liquid cleaners such as Dow or
Lysol foaming bubbles, Top Job, Mr. Clean or similar
type products with a sponge or Mr. Clean Magic Eraser.
To remove hard water stains or mineral build-up, scale
removers such as Lime Away, Rust-out or Whink are
recommended. Do not use abrasive cleaners or pads
such as Ajax, Comet, SOS, Brillo or other similar metal
scouring pads.

Because cleaning products change over time, always
check the manufacturer’s instructions to make sure it is
compatible with plastic. DO NOT use a cleaner if the
label indicates it should not be used on plastics. DO NOT
use spray-on cleaners that require daily use without
immediately rinsing with water to stop the chemical
cleaning reaction because damage will result and void the
warranty.

DDaayy-TToo-DDaayy CClleeaannuupp

Simply wipe the surfaces with a clean towel to remove
watermarks and residues. This Swan Corporation
product can be cleaned with warm water, a soft cloth,
and normal (nonabrasive) household detergents or
cleansers, such as Fantastic, Formula 409, Clorox
Clean-up, Handy Andy, Mr. Clean, or Lestoil. Always
rinse off cleaners within five minutes of application.

If necessary, use a nonabrasive cleaner with a nylon
brush or pad to remove build-up on the shower floor
surface. Do Not use abrasive cleansers, steel wool, or
a wire brush. This will damage the surface.

CCaauullkkiinngg JJooiinnttss

If silicone caulking was applied at installation, inspect
the caulking joints monthly for damage or any signs of
separation from the mating surface. Cracks in the
caulking will allow water to leak into the surrounding
surfaces. Reapply caulking to any joint showing

signs of wear or cracking.

LIMITED WARRANTY

FOR RESIDENTIAL APPLICATIONS

If a Swan Corporation product covered by this warranty
is found to be defective in materials or workmanship,
after inspection by an authorized Swan Corporation
representative, we will repair, or at our option, exchange
the product for a similar model. This warranty extends
for a designated period of time, so long as it remains in
use in its original place of installation.

This warranty covers products installed in accordance
with the Swan Corporation’s installation instructions,
used as recommended, and not damaged due to
misuse, abuse, or improper installation. It does not
apply to any seams or changes made to the product by
professional tradesmen or fabricators.

The warranty applies only to the original purchaser and
installation of these products in residential applications.
It does not apply to commercial applications.

The Swan Corporation’s option to repair or exchange the
products under this warranty does not cover any labor or
other costs of removal or installation, nor shall the Swan
Corporation be responsible for any other incidental or
consequential damages attributable to a product defect
or to the repair or exchange of a defective product.

1-Year Limited Warranty

LIMITED WARRANTY

FOR COMMERCIAL APPLICATIONS

If a Swan Corporation product covered by this warranty
is found to be defective in materials or workmanship,
after inspection by an authorized Swan Corporation
representative, we will repair, or at our option, exchange
the product for a similar model. This warranty extends
for a designated period of time, so long as it remains in
use in its original place of installation.

This warranty covers only products installed in
accordance with the Swan Corporation’s installation
instructions, used as recommended, and not damaged
due to misuse, abuse, or improper installation. It does
not apply to any seams or changes made to the product
by professional tradesmen or fabricators.

The warranty applies only to the original purchaser and
installation of these products in commercial applications.

The Swan Corporation’s option to repair or exchange the
products under this warranty does not cover any labor or
other costs of removal or installation, nor shall the Swan
Corporation be responsible for any other incidental or
consequential damages attributable to a product defect
or to the repair or exchange of a defective product.

1-Year Limited Warranty

IMPORTANT NOTICE

Care and Cleaning Warranty

800-325-7008 17 The Swan Corporation – Swanstone

NOTES:
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________

The Swan Corporation – Swanstone 18 800-325-7008

www.swanstone.com

Form # 513-1

01-11

Save these Installation Instructions for future reference. They

provide important information on cleaning and maintenance of

the Swan Corporation Laundry Tub.