Swanstone CS-1616 Installation

Corner Shower Seat

Model CS1616

 Product Warnings
 Safety Guidelines
 Kit Contents
 Required Tools
 Preparation Tips
 Installation Procedure
 Cleaning & Maintenance
 Surface Repair
 Warranty Information

Register your warranty at www.swanstone.com.

Read and Understand

Before Installing

Form # 194-09-09

800-325-7008 3 The Swan Corporation – Swanstone

The Swanstone Assurance — if our product is

properly installed and maintained, as stated in these

instructions, it will not leak.

RRRReeeemmmmeeeemmmmbbbbeeeerrrr –––– SSSSaaaaffffeeeettttyyyy FFFFiiiirrrrsssstt

tt

The Swan Corporation, the makers of the Swanstone Wall
Systems and Panels, cannot anticipate every possible
circumstance that might involve a potential hazard during
the installation of our product(s). The warnings and
instructions in this installation guide are, therefore, not
all-inclusive. If a tool, installation procedure, or work
method that is not specifically recommended by The Swan
Corporation is used, you must satisfy yourself that it is
safe. You should also make sure that the Swanstone
product(s) will not be damaged by the methods you
choose. The Swan Corporation will not be held
responsible for water damage of any kind in connection
with the installation of one of our Swanstone
bath/shower/panel kits.

To avoid product damage, personal injury, or even possible
death, carefully read, understand, and follow all the
instructions in this installation guide before installing this
product(s). Do not use cleaning fluids or operate power
tools unless you read and understand the instructions and
warnings in this and all other applicable labels or manuals.
Proper use of tools and the products described in this
guide is your responsibility.

WARRANTY

This product is covered by a Limited Lifetime Warranty.
Refer to the Warranty section in this manual for complete
details.

SSaavvee tthhiiss mmaannuuaall ffoorr ffuuttuurree rreeffeerreennccee..

This manual is to be left with the warranty holder and
owner.

Important information on cleaning, maintenance, and
repair is contained within.

IMPORTANT NOTICE

WARNING

IMPORTANT NOTICE: Indicates that equipment or
property damage can result if instructions are not
followed.

Read and Understand the Manual

It is the responsibility of any individual who
installs or maintains this product to fully

understand and follow proper installation and
maintenance procedures. Be aware of the inherent
dangers in the use of power tools when installing this
product. Read and understand all Warnings, Cautions,
and Important Notices in this manual.

Work Safely

DO NOT proceed if any doubt arises about the

correct or safe method of performing anything

found in this or other Swanstone manuals.
The installation of this product can require using power
tools. Do not use power tools without adequate training.
If necessary, hire or consult a trained professional for
expert assistance before continuing.

Use Proper Tools

Always use proper tools which are in good,

working condition during the installation of the

Swanstone products. Using tools other than
those listed could adversely affect the integrity of floors,
pipes, walls, or this product and could result in water
damage or other damage to floors, pipes, walls, or other
portions of your building or home.

CAUTION: Indicates a potentially hazardous
situation which, if not avoided, may result in injury. It
may also be used to alert against unsafe practices.

Slipping Hazard

Do not install this product in the presence of
water. Installing this product without drying all

surfaces, or in the presence of water, could
cause you to slip and fall due to wet floors or spilled
fluids. Personal injury can result from slips or falls.
Before installation, dry all surfaces, including the floor,
with a cloth or paper towel. Clean up all water or spilled
fluids immediately.

Tripping Hazard

Personal injury can result from tripping over
power cords, tools, or other items. DO NOT
leave items laying around the work area.

Personal Protection

Be sure to use all personal protective
equipment, such as sturdy work

boots, preferably with steel toes,
gloves, and hard hat, if necessary, to ensure your own
safety. To prevent possible damage to your hearing,
always wear ear protection, such as earmuffs or
earplugs, when working around power tools.

Eye Protection

Be sure to use all personal protective
equipment to ensure your own safety. To avoid

eye injury, always wear protective glasses with
side shields when using power tools. Also, make sure
no one else can be injured by flying particles when using
power tools.

WARNING: Indicates a potentially hazardous
situation which, if not avoided, could or will result in
serious injury or death.

Fire Hazard

Personal injury or death can
result from a fire caused by

flammable liquids or silicone
sealants. Cleaners or solvents can be highly explosive,
resulting in personal injury or even death, when not used
properly. Clean up any flammable substance
immediately. Sparks or open flames can cause
flammable substances to ignite. DO NOT smoke while
working on or near any flammable substance.

Solvents Hazard

Follow all manufacturer’s safety instructions for
silicone sealants and denatured alcohol.

Alcohol vapors are both flammable and
hazardous to breathe. Silicone vapors may irritate eyes
and nose. Personal injury can result from improperly
handling or use of products such as denatured alcohol.
Always follow the manufacturer’s recommendations for
the safe use of these products. Ventilate any work area
before beginning to apply silicone sealants, cleaning
agents, or solvents.

Fumes Hazard

The fumes from the silicone and
solvents used by the installer can be

harmful if used in an unventilated
room. Always work in a well-ventilated area. To keep
the area well-ventilated, open windows and use exhaust
fans. If adequate ventilation is not achievable or
practical, use respiratory protective equipment.

Dust Hazard

When cutting, drilling, or sanding the

Swanstone product, use a dust

collection method which prevents dust

IMPORTANT NOTICE

The Swan Corporation – Swanstone 4 800-325-7008

Safety Guidelines

CAUTION

WARNING

particles from going into the air. Always work in a well­ventilated area. Always use an OSHA approved dust
mask when cutting, drilling, or sanding Swanstone
products.

Power Tool Hazard

To prevent personal injury or possible
death, always follow the electrical safety

recommendations of the power tool’s
manufacturer. Do not use power tools in an unsafe
manner. Power tools should only be connected to a circuit
protected by a ground-fault circuit interrupter (GFI).

Shock Hazard

Never use electric power tools around

water, condensation, or other liquids.

Electric shock can cause severe
burns, significant injuries, and even death. If an
extension cord is required, always use an OSHA
approved extension cord. Power cords should only be
connected to a circuit protected by a ground-fault circuit
interrupter (GFI).

Electrical Shock Hazard

Contacting l

ive electrical wiring with
power tools or hand tools can cause
serious injury or death. Make sure all

related circuit breakers are turned OFF. Test for live circuits
or wiring inside any wall where installation of the
Swanstone product requires cutting into a wall.

Electrocution Hazard

Water and other liquids conduct electric
current and can create a short circuit,

resulting in injury or death. Keep all
liquids away from electrical cords and power tools. DO
NOT create a short circuit between a source of electricity
and a liquid by being in contact with both simultaneously.

General Information

Required Tools

 Tape measure

 Level and pencil

 Drill with 3/16” and 3/8” drill bits

 1/2” socket or wrench

 Caulking gun

 60 grit sandpaper

 Clean paper towels or shop towels

 Denatured alcohol

Kit Contents

Confirm that all parts of this kit have been included
before beginning installation.

 One solid surface Swanstone corner shower seat

 One stainless steel mounting bracket

 Six 5/16” x 2 “ hex head lag bolts

 Six 5/16” flat washers

 One tube of silicone adhesive

Helpful Hints

 Read these instructions carefully and familiarize

yourself with the various parts of the kit.

 We recommend you allow sufficient time for the parts

in this kit to adjust to room temperature before
beginning installation.

 Store unused materials away from the work area to

prevent accidental damage.

800-325-7008 5 The Swan Corporation – Swanstone

Safety Guidelines General Information

Preparation Tips

 The mounting surface must be free of dirt, film,

waxes, or any other residues.

Caulking Tips

 Follow the instructions on the caulking tube.

 When job is complete, inspect all caulked areas for

gaps and fill as needed.

 Clean up any excess clear silicone using denatured

alcohol and a clean cloth.

 Be very careful not to disturb caulk joints.

Followed carefully, these installation instructions will
result in an easy, trouble-free installation of your
Swanstone product. Any deviations, additions, and/or
deletions from the prescribed installation, without prior
written approval, will void the warranty covering this
product. Not following the directions could also result in
personal injuries, water damage, and other damage to
floors, pipes, walls, and other portions of your building or
home.

Disclaimer

 The information contained in this Installation Manual

is given free of charge. It is based upon technical
data which we believe to be reliable and is intended
for use, by persons having knowledge of this
technical area, at their own discretion and risk.
Swanstone assumes no responsibility for results
obtained or damage incurred from the use of this
material either in whole or in part by the buyer.

 This manual will give you basic instructions for the

installation of the product in a step-by-step sequence
that will work in most types of installations. If you
have an installation application that is not covered in
this manual, please call your local Swanstone
distributor or contact The Swan Corporation directly
for additional information about your application.

 Follow all installation instructions. Failure to follow

these instructions could result in personal injuries,
water damage, or other damage to floors, pipes,
walls, or other portions of your building or home.

Corner Shower Seat Installation

The shower seat is a corner mount design that can add
comfort and convenience to your shower. It is designed
to coordinate with Swanstone tub & shower walls, floors,
and accessories. The molded run-off channel means
water will not pool on top of the seat.

This corner shower seat is designed to fit the following
Swanstone Wall Systems: SSIT-60-3, SS-72-3, SS-60-3,
SS-60-5, SSWP-4872, SK-363672, SK-324872,
SK-344872, SK-326072, SK-346072, SS-3672-3,
DK-363672, DK-324872, DK-344872, DK-326072, and
DK-346072. If you have questions on installing the
corner shower seat in other Swanstone wall systems,
please contact the Swanstone Customer Relations
Department.

The structural strength of the seat and the attachment
bracket, when properly installed on a structural wall,
will hold a maximum weight of 300 pounds. Check all
state and local codes for mounting requirements
before installation. Exceeding the maximum weight
limit will cause the seat to fail or the mounting
bracket to pull away from the wall, resulting in
serious injury.

NOTE: This product is designed so that the mounting
bracket is secured to a strong and stable surface. Any
application that doesn't allow for solid contact between
the mounting bracket and the in-wall support system is
unacceptable.

To prevent serious injury, it is critical that the 2x6 wall
supports be securely fastened to the stud wall. It is
the installers responsibility to make sure this wall
support will hold the 300 lb weight rating of the
shower seat.

1. The shower seat must be installed using sufficient
structural in-wall mounting blocks. A common
shower seat height is 19". A strong 2 x 6 inch wall
support must be installed 16-1/8", on center, off the
subfloor.

The Swan Corporation – Swanstone 6 800-325-7008

General Information Installation Procedure

WARNING

WARNING

2. Use 2-1/2” to 3” long #12 drywall screws to attach
the 2 x 6 supports to the stud wall, as shown.

NOTE: After installing the 2 x 6 wall support, finish out
the wall with drywall and a Swanstone wall panel system
or a wall covering of your choice. After the wall covering
has been installed, set, and allowed to cure, move on to
Step 3.

3. To accommodate the suggested seat height of 19”
use a pencil to mark a line on the shower wall
panels, 16-1/8" up from the subfloor.

Do not mark the Swanstone panels with anything other
than a pencil. DO NOT mark the panel with any
permanent marker, as this will void the warranty.

NOTE: Measure the height from subfloor to the top of
the shower floor shoulder and then up the shower wall
panel to a total height of 16-1/8”.

a. With a level and a pencil, and working out from

the corner, draw a line that will enable you to
properly position the mounting bracket.

b. Using the mounting bracket as a template,

position the bolt holes over the line and mark
the bolt hole locations. Be sure that the
mounting bracket is snug against the corner
before marking the holes.

Dust Hazard

When drilling or sanding the Swanstone
product, use a dust collection method

which prevents dust particles from
going into the air. Always work in a well-ventilated area.
Always use an OSHA approved dust mask when cutting,
drilling, or sanding Swanstone products.

IMPORTANT NOTICE

Installation Procedure

800-325-7008 7 The Swan Corporation – Swanstone

16 1/8"

ON CENTER

POSITION BRACKET HOLES
OVER THE CENTER LINE
AND MARK THEIR
LOCATION

WARNING

4. Drill six pilot holes at the marked locations, using the
3/16” drill bit. Drill through the wall panel and into
the 2 x 6 inch support block installed earlier.

5. Use the 3/8” drill bit to enlarge the 3/16” pilot holes
through the Swanstone wall panel or other wall
material. Only drill the 3/8” holes through the
thickness of the wall panel. Do not drill into the
2 x 6 inch wall support.

Failure to drill the 3/8” clearance holes can cause damage
to the Swanstone or other wall panels when the lag bolts
are installed. Drilling the 3/8” holes too deep will not allow
the lag bolts to adequately secure the mounting bracket to
the wall.

6. Position the mounting bracket in place, align the
holes and secure with six 5/16" x 2" long hex head
lag bolts and washers. Tighten the lag bolts
securely.

The locking tabs on the underside of the
Swanstone seat must engage behind the
stainless steel bracket to prevent the seat from

moving away from the wall. Do not apply
adhesive until you have trial fit the seat and made sure
the locking tabs fully engage. Failure to follow this
procedure may result in serious injury.

7. Trial fit the seat prior to applying adhesive.

a. Make sure the locking tabs molded into the

underside of the seat engage behind the
stainless steel support bracket to prevent the
seat from moving away from the wall.

IMPORTANT NOTICE

The Swan Corporation – Swanstone 8 800-325-7008

Installation Procedure

2X6

SUPPORT

DRILL THE SIX PILOT HOLES

USING A 3/16” BIT.

BLOCK

DRYWALL

SWANSTONE

SHEET

SWANSTONE SHEET

3/8” PILOT HOLE.
DO NOT PENETRATE
2X6 WALL SUPPORT

3/16” PILOT HOLE

CAUTION

b. If the wall corner is not exactly 90 degrees

square, it will be necessary to sand the sides of
the seat in order to achieve a proper fit. Use a
coarse grit (60 grit) sandpaper when sanding the
seat.

Do not use oil-based cleaners, such as mineral spirits, to
clean the Swanstone product. The oil in the cleaner will
prevent the silicone from adhering properly to the wall.

8. Once the seat fits properly, clean the edges of the
seat, 12 mounting tabs, and the shower wall area
above the stainless steel bracket with denatured
alcohol. Apply clear silicone adhesive (supplied) to
the top of the 12 mounting tabs on the underside of
the seat and on the two side edges, as shown.

9. Set the shower seat into place.

a. Make sure the locking tabs molded into the

underside of the seat engage behind the
stainless steel support bracket.

b. Apply a continuous bead of silicone around the

outer perimeter of the shower seat to completely
seal the joint.

c. Use denatured alcohol to clean any excess

silicone from the wall or seat surface.

NOTE: To aid in the bonding process, place a folded
towel or piece of cardboard on the shower seat to
protect it and set a weight, such as a full one gallon
paint can onto the shower seat.

10. Allow 24 hours for the silicone to set. Do not use the
shower during this period.

11. Give these installation instructions to the
homeowner, for future reference. They provide
important information on cleaning, maintenance, and
surface repair of Swanstone wall systems, corner
seats, and accessories.

IMPORTANT NOTICE

800-325-7008 9 The Swan Corporation – Swanstone

Installation Procedure

TRIAl FIT BEFORE YOU

APPLY ADHESIVE

MARK A LINE INDICATING

THE AMOUNT TO BE

SANDED IF NECESSARY.

APPLY SILICONE ADHESIVE TO 12 MOUNTING TABS

APPLY SILICONE ADHESIVE

TO EACH SIDE

AND SIDE OF SEAT.

Care and Cleaning

The Swanstone products are stain and abrasion
resistant; however, the finish requires reasonable care.

Because cleaning products change over time, always
check the manufacturer’s instructions to make sure it is
compatible with solid surface acrylic. DO NOT use a
cleaner if the label indicates it should not be used on solid
surface acrylics. DO NOT use spray-on cleaners that
require daily use without immediately rinsing with water to
stop the chemical cleaning reaction because damage will
result and void the warranty.

Day-To-Day Cleanup

Simply wipe the surfaces with a clean towel to remove
watermarks and residues. All Swanstone products can
be cleaned with warm water, a soft cloth, and normal
household detergents or cleansers, such as Fantastic,
Formula 409, Clorox Clean-up, Handy Andy, Mr. Clean,
Dow Scrubbing Bubbles, Lysol Foaming Tub and Tile
Cleaner, Top Job, or Lestoil. Always rinse off cleaners
within five minutes of application.

Occasional scrubbing with household abrasive cleaners
ensures that the original luster is maintained.

Caulking Joints

Inspect caulking joints monthly for damage or any signs
of separation from the mating surface. Cracks in the
caulking will allow water to leak into the surrounding
surfaces. Reapply caulking to any joint showing
signs of wear or cracking. Failure to inspect and
repair caulking joints will void the warranty.

Surface Repair

Light Scratches

Use 400 grit sandpaper to remove light scratches in the
surface.

Deep Scratches or Gouges

For deeper scratches or gouges, use 220 or 320 grit
sandpaper. A “Scotchbright pad” can be used to blend
the repair into the surrounding area.

IMPORTANT NOTICE

The Swan Corporation – Swanstone 10 800-325-7008

Maintenance and Surface Repair

LIMITED WARRANTY

FOR RESIDENTIAL APPLICATIONS

If a Swanstone product covered by this warranty is
found to be defective in materials or workmanship, after
inspection by an authorized Swan Corporation
representative, we will repair, or at our option, exchange
the product for a similar model. This warranty extends
for a designated period of time, so long as it remains in
use in its original place of installation.

This warranty covers products installed in accordance
with the Swan Corporation’s installation instructions,
used as recommended, and not damaged due to
misuse, abuse, or improper installation. It does not
apply to any seams or changes made to the product by
professional tradesmen or fabricators.

The warranty applies only to the original purchaser and
installation of these products in residential applications.
It does not apply to commercial applications.

The Swan Corporation’s option to repair or exchange the
products under this warranty does not cover any labor or
other costs of removal or installation, nor shall The Swan
Corporation be responsible for any other incidental or
consequential damages attributable to a product defect
or to the repair or exchange of a defective product.

Limited Lifetime Warranty

Swanstone Wall Panels, Trim Kits, and Accessories

LIMITED WARRANTY

FOR COMMERCIAL APPLICATIONS

If a Swanstone product covered by this warranty is
found to be defective in materials or workmanship, after
inspection by an authorized Swan Corporation
representative, we will repair, or at our option, exchange
the product for a similar model. This warranty extends
for a designated period of time, so long as it remains in
use in its original place of installation.

This warranty covers only products installed in
accordance with the Swan Corporation’s installation
instructions, used as recommended, and not damaged
due to misuse, abuse, or improper installation. It does
not apply to any seams or changes made to the product
by professional tradesmen or fabricators.

The warranty applies only to the original purchaser and
installation of these products in commercial applications.

The Swan Corporation’s option to repair or exchange the
products under this warranty does not cover any labor or
other costs of removal or installation, nor shall The Swan
Corporation be responsible for any other incidental or
consequential damages attributable to a product defect
or to the repair or exchange of a defective product.

25-Year Limited Warranty

Swanstone Tub and Shower Wall Panels, Trim Kits, and
Accessories

800-325-7008 11 The Swan Corporation – Swanstone

Warranty

Save these Installation Instructions for future reference. They

provide important information on cleaning, maintenance, and

surface repair of Swanstone products.

www.swanstone.com

Form # 194-09-09