SwannOne SWO-MOS1PA Quick Start Manual

At a Glance

Thank you for choosing the SwannOne™ Motion Sensor. The SwannOne

Motion Sensor detects movement in a surrounding area, triggering actions and

alerting you on your smartphone when it’s important.

QSGMS021214E

© Swann Communications 2015

Key Fob

Indoor

Camera

Outdoor
Camera

Smart Plug

Motion
Sensor

Door/Window

Sensor

Indoor

Siren

Outdoor Siren

Zen

Ther

mostat

Smart

Hub

Discover More SwannOne Smart Home Solutions

EN

Quick Start Guide

Read me first

Motion
Sensor

At a Glance Compliance Information

3M Command™
Mounting Strip

Motion Sensor

Status LED

Passive Infrared
Motion Detector

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1)This device may not cause harmful interference, and (2) This device
must accept any interference received, including interference that may cause undesired
operation.

Disposal and Recycling Information

Correct Disposal of this product. This marking indicated that this product should not be
disposed with other household wastes throughout the EU. To prevent possible harm to
the environment or human health from uncontrolled waste disposal, recycle it responsibly
to promote the sustainable reuse of material resources. To return your used device,
please use the return and collection systems or contact the retailer where the product
was purchased. They can take this product for environment safe recycling.

Battery Safety Information

CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT
TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

www.swannone.com

Activate Pair & Register Mount Need Help?

1 Open the Motion Sensor by pushing

back the release catch on top and
lifting off the rear panel.

2 Remove the protective plastic strip

to engage the battery and activate
the Motion Sensor.

1 Log in to your SwannOne web dashboard at

home.swannone.com.

2 Select My Devices, and select add new from the

Motion Sensors menu.

3 Select Start Learn.

4 Press the Connect button on the Motion Sensor.

The status LED blinks once. Once your Motion
Sensor connects with your hub, the status LED
will blink twice. The on-screen "Motion Sensors

currently registered" counter will increment by 1.

5 Select Stop Learn, and complete the rest of the

setup by following the on-screen instructions.
Once complete, put the rear panel back onto the
Motion Sensor until it clicks into place.

Place Motion Sensor around your home as
required with the included Command™ Strip.

1 Before applying the Command™ Strip, clean

the surface where the Motion Sensor will be
mounted, and make sure it is dry.

2 Fit the Motion Sensor with the Command™

Strip, and then press the Motion Sensor firmly
onto surface for 30 seconds.

3 Test the Motion Sensor by walking in front of it.

The Status LED biinks whenever movement is
detected. You should also receive a status alert
via the SwannOne web dashboard and app on
your smartphone.

Get more information regarding the setup and use of your product on the web at

swannone.com, or contact our multi-lingual support team anytime via:

[e-mail]

USA & Canada 1800 627 2799

UK & Europe 0808 168 9031

Australia 1800 788 210

New Zealand 0400 479 266

AAA

AAA

Plastic
Strip

Connect
Button

Placement Examples

Connect

Button

SwannOne Warranty

Your SwannOne products are backed by a full 12 month guarantee from the date of
purchase. In the unlikely event of anything going wrong, you can have confidence that
your purchase is protected. Refer to swannone.com for terms and conditions.

If the sensor is not connecting as expected, try performing a hard reset by
pressing and holding the Connect button until the status LED blinks rapidly.

Don't place the sensor near heat or cold producing devices such as heaters, air
conditioners, or lamps as they may cause false triggers.