Page 1
CAMERA PLACEMENT DISCOVER MORE
Because the camera is completely wire-free, you'll have a lot
of flexibility with where you place it.
The camera's flat base allows you to put it on a table, shelf, or
anywhere with a flat surface.
The camera also comes with a separate magnetic stand
which can be mounted to a wall with either the included 3M
Command™ adhesive strips or screws and wall plugs. The
stand will hold the camera in place at almost any angle.
If you choose to hang the magnetic stand on
the wall, simply follow the instructions on the
supplied mounting template which will help
you to correctly mark and drill positions for
the screw holes.
This quick start guide provides the information you need
to get started. To learn more about using the mobile app,
download the SAFE by Swann App Manual from our Support
Center at: support.swann.com
NEED HELP?
tech@swann.com
support.swann.com
USA & Canada 1800 627 2799
UK & Europe 0808 168 9031
Australia 1800 788 210
New Zealand 0800 479 266
FCC Statement
This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC RF Radiation Exposure Statement Caution: To maintain compliance with the FCC’s RF exposure guidelines, place the
product at least 20cm from nearby persons.
WARNING: Modifications not approved by the party responsible for compliance could void user’s authority to operate the
equipment.
Frequency Range: 2.4GHz ISM Band; 5.0 GHz ISM Band
CE Output Power: 2412-2472MHz<16dBm; 5150-5350MHz<13dBm; 5470-5725MHz<13dBm
Simplified EU Declaration of Conformity
Swann Communications Ltd declares that this device is in compliance with the essential requirements and other relevant
provisions of Directive 2014/53/EU. A copy of the Declaration of Conformity can be found at: www.swann.com/uk/compliance
Correct Disposal of this product. This marking indicates that this product should not be disposed with other
household wastes throughout the EU. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To
return your used device, please use the return and collection systems or contact the retailer where the product was
purchased. They can take this product for environment safe recycling.
© Swann Communications 2017
QSGINTCAMVER4E
ENGLISH
Smart Security Camera
Wire-Free HD Video Camera
QUICK START GUIDE
Page 2
CAMERA OVERVIEW CHARGE THE CAMERA GET THE APP FIRST TIME SETUP
SAFE by Swann
1
2
3
4
5
1 Night detection sensor
2 Microphone
3 Infrared LEDs for night vision
4 Passive infrared motion sensor
5 LED indicator
6 Reset pinhole button
7 Pairing button
8 USB charging port
9 Port cover
10 Magnetic mount holder
6
7
8
9
10
Before using the camera for the first time, charge it for at
least two hours using the included USB cable.
1 Open the port cover on the back of the camera.
2 Plug the smaller end of the USB cable into the USB
charging port on the camera, and the larger end into a
USB wall charger (DC5V 2.1A power output recommended
for faster charging).
TIP Once you have installed the SAFE by Swann app on your
smartphone and set up your camera, you can use the app to
check the battery charge level and also get notified when the
camera is fully charged.
• If you have an Android smartphone, download and install
the latest version of the SAFE by Swann app from the
Google Play Store.
• If you have an Apple iPhone, download and install the
latest version of the SAFE by Swann app from the Apple
App Store.
SAFE by Swann
Open the SAFE by Swann app
on your smartphone. Create
an account or sign in if you
already have an account.
Tap Pair Device and follow
the on-screen instructions to
set up Wi-Fi and register the
camera to your account.
Loading...