Help Desk / Support Details
Swann Technical Support
All Countries E-mail: tech@swann.com.au
Telephone Helpdesk
UNITED STATES toll free
877-274-3695
(Sun-Thurs, 2pm-10.30pm PST)
800-627-2799
(Mon-Fri, 9am-1pm PST)
USA Exchange & Repairs
562-777-2551
(Mon-Fri, 9am-5pm PST)
AUSTRALIA toll free
1300 13 8324
(Mon-Fri, 9am-5.30pm Aus EST)
+61 3 8412 4610
(Mon-Fri, 9am-5.30pm Aus EST)
See http://www.worldtimeserver.com for information on different time zones
and the time in Melbourne Australia compare to your local time.
English
Night Hawk
Extra Wireless Outdoor Camera
With 4 Channel Switching
International
Warranty Information
Swann Communications warrants this product against defects in workmanship and material for
a period of one (1) year from it’s original purchase date. You must present your receipt as
proof of date of purchase for warranty validation. Any unit which proves defective during the
stated period will be repaired without charge for parts or labour or replaced at the sole
discretion of Swann. The repair or replacement will be warranted for either ninety days or the
remainder of the original one year warranty period, whichever is longer. The end user is
responsible for all freight charges incurred to send the to Swann’s repair centres.
end user is responsible for all shipping costs incurred when
other than the country of origin. The warranty does not cover any incidental, accidental or
consequential damages arising from the use of or the inability to use this . Any costs
associated with the fitting or removal of this product by a tradesman or other person or any
other costs associated with its use are the responsibility of the end user. This warranty applies
to the original purchaser of the only and is not transferrable to any third party.
Unauthorised end user or third party modifications to any component or evidence of misuse or
abuse of the device will render all warranties void.
product
product The
shipping from and to any country
product
www.swannsecurity.com
8
If this device does not work when you first plug it in,
do not take it back to the store.
Contact the Swann Helpdesk using our fast e-mail service
tech@swann.com.au or call us on one of the Toll-Free
numbers shown on the back cover of this booklet.
Most problems can be quickly and easily fixed with a simple
e-mail or a quick chat with one of our friendly technical staff.
(Toll-Free available in the US and Australia only)
Note: Wireless Networks (WiFi) may interfere with and/or experience interference caused by
the transmitterin this unit. Changing the receiver to another channel/frequency or setting the Wireless
Network (i.e. Wireless Access Point) to a frequency further away from the camera’s set frequency can
alleviate this problem. Consult the documentation of your Wireless LAN device for information on how
to change the transmission frequency. These cameras work with most wireless camera receivers that
support 2414MHz, 2432MHz,
Installation Guide
Index
Technical Specifications
Introduction
This package comes with...
Installing your Nighthawk Camera
Camera Features
Important Information about your Nighthawk Camera
Troubleshooting, Hints & Tips
Technical Specifications
Help Desk / Support Details
Warranty Information
2
2
2
2
3
3
4
4
5
5
6
6
7
7
Back Cover
Back Cover
Back Cover
Back Cover
Introduction
The Swann Nighthawk Camera incorporates the latest in advanced technology.
We feel confident that you will be pleased with the quality and features of this product.
The Swann Nighthawk Camera allows you to transmit pictures with ease. As the radio waves it uses
have a frequency of 2.4GHz, they can be received within a radius of up to 328ft/100m in open line of
sight. The Nighthawk Camera comes with 2 power sources (9V battery and mains adaptor) so that you
have the option of using different power methods for different locations and conditions, to ensure that
you have the best options for your situation.
Please note: The Swann Nighthawk Camera broadcasts video in the public domain.
The video signal is not encrypted and could potentially be viewed by anyone with a similar
2.4GHz receiver unit. Please keep this in mind when positioning and using any wireless
camera equipment.
This Package Comes With ...
• 1 x 2.4GHz Wireless Nighthawk Camera / Built-in Transmitter with Stand
• 1 x Mains Power Adaptor (8V for use with Camera)
• 1 x 9V Battery Snap (battery not included)
• This Instruction Sheet
If any of these items are missing, please contact your retailer.
Channels: 1-2414, 2-2432, 3-2450 & 4-2468MHz
RF Output Power: CE, FCC & C-tick compliant
Operating Power: 8V DC 200mA
Power Consumption: 100mA
Size: 54 x 43mm (2 / ” x 1 / ”)
1 7
8 10
Antenna: Omni-directional
Transmitting Range: Up to 328ft (100M) line of sight
Weight: 7 / oz (220 grams)
3
4
Operating Temperature: 32° - 122°F ~( 0° - 50°C)
Sensor: 1/3”(8.5mm) Colour CMOS
Horizontal Resolution: 380 TV lines
Auto Electronic Exposure: 1/60 - 1/15000 sec.
Minimum Illumination: 1 Lux@ f1.2
Signal to Noise Ratio: >48dB
Board Lens: / ” (5.6mm)
7
32
View Angle: 60 degrees
Video System: NTSC 60Hz USA & Canada ~ PAL 50Hz AU, UK & EU
Automatic Exposure / Gain / White balance.
FCC Notice
We, Swann Communications of 10612 Shoemaker Avenue, Bldg A, Santa Fe Springs, CA 90670 USA, declare
under our sole responsibility that the Nighthawk Camera:
SW-P-WOCEX
To which this declaration relates:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communication. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC NOTICE
This device co mp li es w ith Part 15 of FCC Rules.
Operation is sub je ct t o the following conditi on s:
(1) This device ma y no t ca use harmful interfere nc e, a nd
(2) this device mu st a cc ept any interference re ce iv ed,
including in te rf er ence that may cause undes ir ed o peration
2 7
This product complies with standards including Low Voltage Device Directive 73/23/EEC; EMC Directive 89/336/EEC and
R&TTE Directive 1999/5/EC. It passed the subject tests by the authority concerned and is authorized to bear CE mark.
CE Notice
Troubleshooting your Night Hawk Camera Installing your Night Hawk Camera
Poor Picture: Realign antennas until image quality improves, slightly adjust the position of the
Camera or Receiver. Change the location of the Camera, or use a different height or angle to see if
the image improves. In some cases interference may be caused by another device on a similar
frequency to the channel you are using.
Lines only - no clear picture: Check to confirm there is no microwave oven or other 2.4GHz
equipment operating close by ie; Cordless Telephones, Wireless Baby Monitors, Wireless LAN
equipment etc . Make sure the Receiver is on the correct channel.
Picture ghosting or interference: Some home appliances such as Wireless LANs, 2.4GHz
portable telephones and Microwave ovens operate on or near the 2.4GHz frequency. If you receive
interference from such an appliance, try moving the Camera or Receiver to location further away
from the appliance or in the event of interference from a Wireless LAN device, try changing the
Wireless LAN to a different channel to improve the signal quality.
No picture: check the receiver to confirm it is turned ON and make sure the A/V connection of the
Receiver is not plugged into the Audio Out socket. Make sure the Receiver is on the correct channel.
Check to ensure the camera is plugged in and has power. Check that the channel on the receiver is
the set to Channel x.
Red haze over picture: In some cases where the sun shines into the front of the camera a faint
red glow can be seen. Move the camera to a shaded location, or fit a hood to stop sunlight entering
the camera lens directly.
Foreground is dark while background is too bright: If the camera is looking from a dark area
towards a light area in some cases the automatic exposure can find it difficult to balance the image
correctly. Change the location of the camera so that the point of greatest interest has the largest
area of the image.(if you want to see the bright area, move the camera so that almost all of the
screen shows this area. If you want to see the darker area, move the camera so that most of the
image shows this area.
The Wireless Outdoor Camera can be switched to four frequencies to assist in avoiding interference.
To set or change frequencies, take off the front cover by unscrewing it anti-clockwise fig.(1). Please see
the below illustration fig.(2) for frequency settings. To change the frequency/channel on the receiver,
press the appropriate button to cycle through the channels.
Fig. (1)
Unscrew front case anticlockwise to remove
Changing these switch settings changes the frequency that
the camera transmits on. Once you have set the channel on
the camera, select the same channel on your receiver. If you
experience interference try different channels. Make sure
multiple cameras are set to different frequencies so you can
use them in the same area or on the one receiver.
1) Connect both the Nighthawk Camera and the Receiver to their respective
Fig. (2)
1
2
Front view of lens with
switches bottom right,
note the numbers 1 & 2
indicate the bottom of
the switch
Frequency channel settings
Channel 1
Both switches up
2414MHz
1 2
Channel 2
Left up & Right down
2432MHz
1 2
Channel 3
Left down & Right up
2450MHz
1 2
Channel 4
Both switches down
2468MHz
1 2
power adaptors.
2) Connect the Receiver to the equipment you wish to view the camera on (monitor, TV, VCR
etc) using the supplied RCA cable.
3) After connecting both the Camera and the Receiver make sure the receiver is switched
to the same channel as the Nighthawk Camera.
Obtain the best picture by adjusting the position of the Nighthawk Camera and Receiver unit
to suit. Try slightly different locations of either unit for optimum results.
4) If you are mounting the camera to a ceiling or eave, unscrew the camera stand from the
camera body and carefully screw it into position on the top side of the camera using the
two holes that are provided to ensure the picture is not upside down.
5) Align the antenna of the receiver toward the antenna of the Nighthawk Camera and test
the reception quality.
36
Camera Features Important Information about your Night Hawk Camera
To take advantage of any unused channels on your receiver you can purchase additional Night
Hawk Extra Cameras, or a MicroCam IV Color Indoor Camera
(product code SW-P-MC4) can be used. The MicroCam IV Camera has similar DIP switches to
the Nighthawk Camera, which allow the use of any of the other available channels on your
receiver.
Camera Power Adaptor (8V)
Microphone in
power socket
Night Hawk Camera with Stand
9v Battery Adaptor
! Best Results are achieved where there is a clear “line of sight” between the Nighthawk
Camera transmitter and Receiver.
! Try to avoid obstacles such as trees, walls, cars, trucks and buildings when maximum range is
required.
! Interference from certain electronic equipment or the moving human body can also affect the
range obtainable.
! Please test all devices before final installation because transmission quality can often be
improved by moving the components slightly.
! Turn off the transmitter and receiver if the system is not in use.
! Do not touch the antennas when the system is switched on.
! Do not place the receiver behind a monitor or TV.
! To avoid the risk of damage to Nighthawk Camera, use only the supplied power adaptors.
! Don’t place above or near a heat source which may cause the equipment to overheat.
! Microwave ovens can cause interference and diminish the quality of the signal if the
Nighthawk Camera or Receiver are located close by.
! Beware of humid locations. Water droplets or spray may damage the units.
If condensation does occur, do not use until the equipment has dried out.
! Never paint or attach metallic labels or stickers of any kind.
! Do not use two Nighthawk Camera systems operating at the same time in the same area
using the same channel. This will result in picture interference. Switch one camera to one of
the unoccupied channels using the DIP switches.
Night Hawk Camera with Stand When
mounted under eave or roof
IMPORTANT: Due to the power consumption requirements of this product, we highly
recommend the use of a 9 volt battery only for short term portable use.
4
! Do not cut the DC power cable of the Nighthawk Camera to fit with another power source.
This may result in damage to the Nighthawk Camera & any unauthorised modifications will
void your warranty.
5
Loading...