Swann SWPRO752CAM User Manual

English

PRO-752 Dome

M752CAM020113E

Warranty Information, Verifications & Warnings

Swann Communications warrants this product against defects in workmanship and material for a period
of one (1) year from its original purchase date. You must present your receipt as proof of date of purchase
for warranty validation. Any unit which proves defective during the stated period will be repaired without
charge for parts or labor or replaced at the sole discretion of Swann. The end user is responsible for all
freight charges incurred to send the product to Swann’s repair centers. The end user is responsible for all
shipping costs incurred when shipping from and to any country other than the country of origin.

The warranty does not cover any incidental, accidental or consequential damages arising from the use
of or the inability to use this product. Any costs associated with the fitting or removal of this product by
a tradesman or other person or any other costs associated with its use are the responsibility of the end
user. This warranty applies to the original purchaser of the product only and is not transferable to any
third party. Unauthorized end user or third party modifications to any component or evidence of misuse
or abuse of the device will render all warranties void.

By law some countries do not allow limitations on certain exclusions in this warranty. Where applicable
by local laws, regulations and legal rights will take precedence.

For Australia: Our goods come with guarantees which cannot be excluded under Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and for compensation for any other

reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the

goods fail to be of acceptable quality and the failure does not amount to major failure.

Warning

Modifications not approved by the party responsible for compliance could

void user’s authority to operate the equipment.

• Make sure product is fixed correctly and stable if fastened in place

IMPORTANT NOTE: All jurisdictions have specific laws and regulations relating to the use of cameras.

Before using any camera for any purpose, it is the buyer’s responsibility to be aware of all applicable laws

and regulations that prohibit or limit the use of cameras and to comply with the applicable laws and

NOTE: This equipment has been tested and found to comply with the limits for Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected

• Consult the dealer or an experienced radio/TV technician for help

These devices comply with part 15 of the FCC Rules. Operation is subject to the following two conditions:

• These devices may not cause harmful interference, and

• These devices must accept any interference received, including interference that may cause

undesired operation.

IMPORTANT SAFETY INSTRUCTIONS

• Do not operate if wires and terminals are exposed

regulations.

FCC Verification

Introduction

Congratulations on your purchase of this Swann PTZ Camera!
This installation and setup guide will walk you through the basics of connecting the
PTZ camera to your DVR, and walk you through the settings on the DVR you’ll need
to use to control the camera.

Be aware that the camera must be connected to a compatible DVR to operate

correctly.

The included stand-alone RS485 controller will operate the basic features of the
camera, and access the on-screen display (OSD). You won’t be able to program the
camera properly or integrate it’s functions with your system unless your DVR is
configured to do so.

Compatibility

This Swann PTZ camera is compatible with most current Swann DVRs. We can
confirm that it will work with the following DVR models:

1200, 1300, 2500, 2550, 2600, 3000 and 4000 series DVRs.

This is not an exhaustive list - since the time of publication we may have released
newer DVRs with which this camera is compatible. Check your DVR documentation
to learn more. Any Swann DVR with an RS485 port should be compatible with this
camera.

IMPORTANT: If mounting the camera outside, be sure to properly seal all joints in

the mounting arm/bracket using a silicon sealant. If this is not fully sealed, water

can enter the dome causing malfunction or failure.

Package Contents

PRO-752 Camera

RS485 Controller

Camera Cable

Extension Cable

Screws and Mounting Hardware

Power Supply (not pictured)

Power Splitter (not pictured)