Swann SWPRO-1080FLB Instruction Manual

5

6

Limited Warranty - Terms & Conditions

Swann Communications warrants this product
against defects in workmanship and material for
a period of one (1) year from its original purchase
date. You must present your receipt as proof of
purchase for warranty validation. Any unit which
proves defective during the stated period will
be repaired without charge for parts or labour
or replaced at the sole discretion of Swann. The
end user is responsible for all freight charges in­curred to send the product to Swann’s repair cen­tres. The end user is responsible for all shipping
costs incurred when shipping from and to any
country other than the country of origin.
The warranty does not cover any incidental, ac­cidental or consequential damages arising from
the use of or the inability to use this product. Any
costs associated with the fitting or removal of this
product by a tradesman or other person or any

other costs associated with its use are the re­sponsibility of the end user. This warranty applies
to the original purchaser of the product only and
is not transferable to any third party. Unauthor­ized end user or third party modifications to any
component will render all warranties void. By law
some countries do not allow limitations on certain
exclusions in this warranty. Where applicable by
local laws, regulations and legal rights will take
precedence.

For Australia: Our goods come with guarantees

which cannot be excluded under Australian Con­sumer Law. You are entitled to a replacement
or refund for a major failure and for compensa­tion for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of ac­ceptable quality.

M1080FLB120416CAM16E | © Swann 2016

FCC Verification

This equipment has been tested and found to comply with the limits for Class B digital device, pursu­ant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is con­nected

• Consult the dealer or an experienced radio/TV technician for help

These devices comply with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) These devices may not cause harmful interference.

(2) These devices must accept any interference received, including interference that may cause unde­sired operation.

HD Bullet
Security Camera

1080p HD Bullet Camera

EN

INSTRUCTION MANUAL

Helpdesk/Technical Support

Technical Support E-mail: [e-mail]

Telephone Helpdesk

USA Toll Free 1-800-627-2799

USA Parts & Warranty 1-800-627-2799

(M-F, 9am-5pm US PT)

AUSTRALIA 1800 788 210

NEW ZEALAND Toll Free 0800 479 266

UK 0808 168 9031

Security Made Smarter

Video & Audio
Output

1 2 3 4

Congratulatio ns on your purchase of t his HD
Bullet Security Camera.

• Use the On-Screen D isplay (OSD) con troller
& built-in softw are to customi ze the camer a
settings includi ng color, brightness & wide
dynamic range fo r the best video qua lity
every time

• This camera can b e used in combination
with other analog su rveillance technolog y
including AHD, T VI, CVI from Sw ann &
other brands. It ’s the perfect addi tion if you
already have a re cording solution (DVR) &
need extra cam eras

• The camera joy stick is used to set the
signal modes for the c amera. Hold for 2
seconds; Up for Ana log, Left for AHD, R ight
for TVI and Dow n for CVI.

Important note: All jurisdict ions have specific

laws and regula tions relating to the u se of
cameras. Befor e using any camera f or any
purpose, it is the bu yer’s responsibil ity to be
aware of all applic able laws and reg ulations
that prohibit or limi t the use of cameras and to
comply with the appl icable law s and regulati ons.

Warning: Modifications not approved by the party

responsible for compliance could void user’s
authority to operate the equipment.

Important safety instructions

1) Make sure product is fixed correctly and stable

if fastened in place.

2) Do not operate if wires and terminals are

exposed.

Introduction Choosing a location for your Camera

This camera has an on-screen configuration menu to
configure various image settings as they apply to the
camera and the scene that you wish to view.

• You should endeavor to set the camera up close
to the area you wish to view before you install
the camera so that you have access to the
joystick and can adjust the image settings.

• How you’re going to connect the camera to your
monitoring system; you should plan the route
from the recorder to each camera

• How to keep the camera out of harm’s way. It’s
recommended to mount your cameras in an
elevated position to prevent easy access.

• Place your camera as close to the area of
interest as practicable. The best position is from
about 3-4m (9-13ft) above looking slightly down.

• Although the sky looks nice when you look at
the live view from your camera, it is an unlikely
direction for an offender to approach from.
Keep the camera pointed down away from the
sky or ceiling. This will also minimize glare from
lighting affecting the image.

• Think about the most likely way a potential
offender may approach your home and position
your cameras to give you the best coverage of
these areas.

• The camera’s casing is resistant to water,
different weather conditions and tampering.
However, the cable and connectors are
vulnerable and require protection.

• Even though the camera is weather and water­resistant, prolonged exposure to adverse
weather conditions such as sunlight or
excessive moisture, may eventually damage
the internal components of the camera and
adversely affect its performance.

Positioning the cables

1) When running the cable, try to avoid bending it at

sharp angles.

2) Avoid positioning the cable live electrical wiring.

AC electricity generates radio “noise” which can
interfere with the signal from your camera.

3) Do not stretch or apply force to the cable greater

than 25lbs/11kgs.

Connecting your Camera Mounting your Camera

Connect the video & audio
output and DC power
connection on the camera
to the corresponding
connections on the video,
audio & power cable.

Connect the video (and audio if available)
connection on the other end of the cable
to a video (and audio) input on the DVR.

Connect the power
adapter to the cable
power socket and then to
a spare wall socket.

For multi-camera packs, use a
power splitter cable (if included).

Twist the video connection
to lock it in place.

PTZ

7

5 3

1

8

6 4

2

eSATA

HDMI LAN & USB B A

DC 12V

IN

VGAVIDEO IN AUDIO OUT

AUDIO IN

Video, Audio &
Power Cable

Joystick

The joystick is used
to set the signal
from the camera.

1

2

3

i

The camera can be mounted onto a flat surface using screws. The surface must have
sufficient strength to hold the camera.

• Position the camera in the location you want to mount it, and mark the screw holes on
the surface to position the screws on the surface. Then, using appropriate screws for
the surface you’re fixing the camera to, secure the camera into place.

• If you’re mounting to a wooden surface, then screw the camera directly to the surface.

• If you’re mounting to a masonry surface (bricks, concrete or similar) then you’ll need to
use the included wall plugs.

Aiming the camera

You can use the included allen key to adjust the camera angle.

• To adjust the orientation, loosen the screw indicated by 1. This
enables you to rotate the camera so no matter what direction it is
facing, your images will be the right way up.

• To tilt up and down, loosen the indicated by 2.

• To pan left and right, loosen the screw indicated by 3.

Be sure to tighten the screws back securely to lock the camera’s position
in place after you finish adjusting the camera angle.

2

1

3

For more information on this product visit www.swann.com

Be protected & see every detail in 1080p HD

• Seeing is believing with 1080p (2.1 Megapixels) HD perfect for close up detail such as license plates,
faces, clothing colors & more

• See higher detail over longer distances with a powerful fixed 6mm lens

• Latest infrared array LEDs produce amazing night vision clarity in low light to 100ft / 30m, with
sturdy aluminum camera construction to suit indoor & outdoor applications with IP66 rating for
any weather conditions

• Camera features a built-in microphone so you can see & hear what’s happening^ and longer
100ft/30m cable offers more options when choosing a mounting location for the camera

• Use the On-Screen Display (OSD) controller & built-in software to customize the camera settings
including color, brightness & wide dynamic range for the best video quality every time

• This camera can be used in combination with other analog HD surveillance technology including AHD,
TVI, CVI from Swann & other brands. It’s the perfect addition if you already have a recording solution
(DVR) & need extra cameras

• Deter thieves, safeguard loved ones, protect your property & cut the cost of crime with this superior
surveillance camera from Swann

SWPRO-1080FLB

HD Bullet Security Camera

1080p HD Bullet Camera with 6mm Fixed Lens

HIGH DEFINITION

1080P

DAY/NIGHT VISION

EASY INSTALLATION

WEATHER PROOF

LONG RANGE LENS

AUDIO MONITORING

6mm

1080PPRO-SERIES HD

Security Made Smarter

#

1

Works with all leading

surveillance brands

*

Universally

Compatible

For more information on this product visit

www.swann.com

Our Promise

Swann stands by its promise of Lifetime Support
to make advanced security easy to use, install and
maintain. Everything is in the pack but if you need
it Swann’s help desk is available 24 hours a day,

7 days a week for the life of the product.

Installation is easy

Do-it-Yourself

Installing this Swann product is simple. For
instructions, tips and videos see the operating
instructions in this pack or visit www.swann.com

Professional Installation

Need extra help? We have an installer in your
region! For more visit www.swann.com

What’s in the box?

All installation accessories included

• PRO-1080FLB™ Camera

• BNC Cable 100ft / 30m

• Power Adapter

• Mounting Screws & Plugs

• Operating Instructions

• Theft Deterrent Stickers

See the difference

Enjoy video resolution that’s superior to traditional
security systems with realistic colors, wide angle and
impressive image quality.

Specifications

PRO-1080FLB™ CAMERA

Video

Video Quality 1080p
Viewing Angle 56°

Night Vision

Night Vision Distance Up to 100ft / 30m
IR cut Filter Yes

General

Indoor / Outdoor Indoor / Outdoor, IP66 rated
Audio Range Up to 16ft / 5m

Operating Power DC 12V
Operating Temperature -4°F ~ 122°F / -20°C ~ 50°C
Body Construction Aluminum
Dimensions - Camera LWH 7.68” x 2.76” x 2.56” /
195mm x 70mm x 65mm
Weight - Camera 1.37lbs / 620g

Code

Swann Code SWPRO-1080FLB

Take a closer look

Weather resistant

aluminum casing

56° Viewing angle

Powerful night

vision from Infrared

array LEDs

Mounting holes for

easy installation

Color video

image sensor

HD Bullet Security Camera

1080p HD Bullet Camera with 6mm Fixed Lens

Traditional Surveillance

1080p HD

* As the wor ld’s #1 name in DIY vide o

sur veill ance Swann is proud to laun ch
new Univ ersally Comp atible camer as
that are buil t for the leadin g Analog HD
sur veill ance technolo gy including AH D,
TV I, CVI fro m Swann & other bra nds

PROSERIES HD

On-Screen Display

INSTRUCTION MANUAL