Swann SW3010W, SW3010B Instruction Manual

INSTRUCTION MANUAL

SW3010W / SW3010B

Washing Machine Instruction Manual

CONTENTS Page

A NOTE T O YOU

Thank you for buying a SWAN appliance.
SWAN washers are easy to use, save time, and help you manage your home better.
This manual contains valuable information about how to operate and maintain your washer properly and safely.
Please read it carefully.

" Economic wash system

Using artificial intelligence, the washer uses minimum energy and water by
selecting optimal water lever and washing time.

" Low noise system

The washer minimizes the washing and spinning noises by sensing the amount
of laundry.

" Child-Lock

The Child-Lock system has been used to prevent children from pressing any
button to change the program during operation.

PARTS AND FEATURES.................................................................................................................2

WASHER SAFETY...........................................................................................................................3

INSTALLATION INSTRUCTIONS....................................................................................................4

INLET HOSE CONNECTION...........................................................................................................5

ELECTRICAL SAFETY ....................................................................................................................5

ELECTRICAL REQUIREMENTS .....................................................................................................6

OPERATING YOUR WASHER........................................................................................................7

THE FUNCTIONS OF THE CONTROL PANEL...............................................................................9

WASHING PROCEDURE AND PROGRAM SELECTION.............................................................10

MAINTENANCE .............................................................................................................................19

HOW TO CLEAN THE FILTER......................................................................................................20

REMOVING STAINS......................................................................................................................21

TROUBLE SHOOTING ..................................................................................................................22

STILL NOT SOLVED THE PROBLEM; .........................................................................................23

SPECIFICATION............................................................................................................................24

Customer Service Helpline:01189 252545

2

PARTS AND FEATURES

The parts and features of your washer are illustrated on the page.
Become familiar with all parts and features before using your washer.

Accessories

Hose drain Inlet hose Manual Cap holder(3EA)

ADJUSTABLE LEG

CONTROL PANEL

DOOR

DETERGENT DRAW

INLET HOSE

FILTER COVER

POWER CORD

DRAIN HOSE

3

Save these instructions

Your safety is important to us.
To reduce the risk of fire, electrical shock, or injury when using your washer adhere to the
following basic precautions.

Understanding your responsibilities

• Do not use chlorine bleach and ammonia or acid(such as vinegar or rust remover) in the same
wash. Hazardous fumes can form.

• Unplug power supply cord before attempting to service your washer.

• Do not wash fiberglass material.
Small particles can stick to fabrics washed in following loads and cause skin irritation.

• Do not spray water on the control panel of the washer.
It could cause fire or an electric shock.

• In case of the dual valve model, if you connect only cold water inlet valve, while water
temperature is selected as hot or warm, there can be water leakage from unconnected water
inlet valve.

• This appliance must be grounded.

• Flammable fluids (dry-cleaning solvents,
kerosene, gasoline, etc.) should not be
used or stored in or near your washer.
Do not add flammable fluids to your wash
water.These substances give off vapors that
can create a fire hazard or explosion.

• After starting a cycle, do not reach into the
washer until all motion stop.

• Do not tamper with the controls.

• The appliance is not intended for use by
young children or infirm persons without
supervision.

• If the supply cord is damaged, it must be
replaced by the manufacturer, or its service
agent or a similarly qualified person in order
to avoid a hazard.

Please ...

• Have only a qualified person install, repair,
or replace parts on washer.

• Maintain washer properly.

• Protect washer from the weather and keep
it where the temperature will not fall below
freezing.

• Do not install the washer at a place of
extremely high humidity. It could cause an
electric shock or a short circuit.

• Connect washer to the correct outlet,
electrical supply, water supply, and drain
supply.

Read all instructions before using your washer

WASHER SAFETY

4

Removing transit bolts

1. Before operating the washer, remove the
transit bolts(3ea) along with the rubber.

• If the bolts are not removed, it may cause
heavy vibration, noise and malfunction.

2. Unscrew the 3 bolts with the 10mm hex
wrench or spanner or cross-tip screwdriver.
Keep the 3 bolts for a later time.

• When the appliance is transported, transit
bolts will be re-used.

3. Close the holes with the cap holders supplied.

Location of washer

• Check location where the washer will be installed. Make sure you have everything necessary for
correct installation.

• Do not place or store your washer below 0°C (32°F) to avoid any damage from freezing.

• Do not place or store laundry products on top of washer at any times.

• Install the washer on’a level, flat’ solid floor.

If the washer is installed on an unsuitable floor, it could make
considerable noise, vibrate severely and cause a malfunction. If the
washer is not level, adjust the feet located on the base of the
machine up or down until the item is level. (see page 6)

• Ventilation openings must not be obstructed by carpeting when the
washer is installed on a carpeted floor.

• Leave some space (right & left : 2cm, rear : 10cm).

• In case of built-in installation, the distance between top of the washer

and bottom of upper plate should be at least 3mm.

INSTALLATION INSTRUCTIONS

Laundry

Tub

Washer

approx.

2cm

Drain Hose

5

The washer should be connected to the water mains using new hose sets and old hose sets
should not be reused.
Connect the inlet hose to the cold water inlet valve.

INLET HOSE CONNECTION

THIS APPLIANCE MUST BE PLUGGED INTO AN EARTHED SOCKET.

Before switching on, make sure that the voltage of your electricity supply is the same as that
indicated on the rating plate. This product is designed to operate on 220 – 240V AC; 50Hz.
Connection to any other power source may damage the unit.

This product may be fitted with a non – rewireable plug. If it is necessary to change the fuse in the
plug, the fuse cover must be refitted. If the fuse cover becomes lost or damaged, the plug must
not be used until a suitable replacement obtained.

If the plug has to be changed because it is not suitable for your socket, or becomes damaged in
any way, it should be cut off and an appropriate plug fitted following the wiring instructions below.
This should be carried out by a qualified electrician. The plug removed must be disposed of
safely, as insertion into a 13 Amp socket is likely to cause an electrical hazard.

ELECTRICAL SAFETY

1 Connect the inlet hose to

the water tap by screwing
the connector tightly.

2 Connect the connector-

inlet supplied if necessary.

3 Connect the inlet hose

adapter to the water inlet
of a washer and turn it to
be fixed.

*Check the packing in the inlet

Connector

Hose Connector

Rubber
Packing

Connector

inlet

Connector

Hose Connector

Rubber
Packing

6

ELECTRICAL REQUIREMENTS

Drain system

• Never forget to install drain hose before operating your washer.

• Connect the drain hose to the drain outlet at the back side of the washer.

•

Top of drain outlet must be at least 60cm high and no higher than 100cm from bottom of washer.

• When installing the drain hose to tub(sink), secure it tightly with a string.

• Proper securing of the drain hose will protect the floor from damage due to water leakage.

• When the drain hose is too long, do not force it back into the washer.

This will cause abnormal noise.

Level adjustment

1 If the washer is installed on an

unsuitable floor, it could make
considerable noise, vibrate and
cause a malfunction.

The wires in this mains lead are colored in accordance with the following code:

Blue = Neutral Brown = Live Green/Yellow = Earth

As the colours of the wires in the mains lead of this appliance may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows (refer to the plug
wiring diagram).

The wire which is colored BLUE must be connected to the
terminal which is marked with the letter N or colored Black.
The wire which is colored BRO WN must be connected to
the terminal which is marked with the letter L or colored
Red.
The wire which is coloured GREEN/YELLOW must be
connected to the terminal which is marked E.
If a 13Amp (BS1363) plug is used, a 13Amp (BS1362) fuse
must be fitted, or if any other type of plug is used, a 13Amp
fuse must be fitted, either in the plug or adaptor, or on the
Distribution Board.

Wiring Instructions

GREEN

&

YELLOW

(Earth)

BROWN

(Live)

BLUE

(Neutral)

FUSE

Laundry tub

max. 100cm
min. 60cm

Hose

Retainer

ca. 105cm

max. 100cm

min.60cm

max. 100cm
min. 60cm

Tie

Strap

7

2 Adjust the level of washer using adjustable legs.

• Please check if there is any gap between the
four adjustable legs and the floor.

• Adjust the level of washer by turning
adjustable legs. And make sure that the
washer does not rock.

• After the adjustment is finished, turn the fixing
nuts up tightly so that the washer maintains the adjustment.

3 Make space sure that the washer does not rock when you

press down the four corners of the washer’s top.

adjustable leg

Fixing Nut

NOTE

We recommend that you use a spirit level to ensure the
item is level.

OPERATING YOUR W ASHER

To obtain the best washing results, you must operate your washer properly.
This section gives you this important information.

• Close zippers, snaps, and hooks to avoid

snagging other items.
Remove pin, buckles, and other hard
objects to avoid scratching the washer
interior.

• Empty pockets and pull them inside out.

• Turn down cuffs and turn synthetic knits
inside out to avoid pilling.

• Tie strings and sashes to avoid tangling.

• Treat spots and stains.
(See “Removing stains” on page 21)

Preparing clothes for washing

8

• Drop items into washer loosely. Items should move
easily through wash water for best cleaning and
wrinkle-free results.

• Load washer properly and select correct load size
setting.
Overloading and selecting a setting too small for
the wash load can :

- Cause poor cleaning

- Increase wrinkling

- Create excessive lint

- Wear out items faster (because of pilling)

• Mix large and small items in each load. Load evenly
to maintain washer balance.
An unbalanced load can make the washer vibrate
during spin.

• Reduce wash time when using a small load size
setting. Load with only a few small items needs
less wash time.

• Use a large load size setting to reduce wrinkling
with permanent press clothes and some synthetic
knits. These items should have more room to move
in the water than heavy items. (towels, jeans)

Loading

1 Detergent case 2 Adding fabric softener

• If desired, add measured liquid fabric
softener to the softener inlet.

• Pour liquid fabric softener into the
dispenser using the amount
recommended on the package.

• Do not exceed the maximum fill line.
Overfilling can cause early dispensing of the
fabric softener which could stain clothes.

• Do not open the detergent case when
water is supplied.

• Avoid pouring fabric softener directly on
the clothes.

Adding detergent

• Separate heavily soiled items from lightly soiled ones, even if they would normally be washed together.

• Separate dark colors from light colors, colorfast items from non-colorfast item.

Sorting

Soil (Heavy, Normal, Light) Separate clothes according to amount of soil.
Color (White, Lignts, Darks) Separate white clothes from colored clothes.
Lint (Lint producers, Collectors) Wash lint producers and lint collectors separately.

Main wash

Pre wash

Fabric softener

• Please use only the powder detergent for the front loader washing machine.

• Please use the proper amount of detergent in conformity with the instruction of the detergent manufacturer.

• A use of a large amount of fetergent more than the recommended amount can cause many soapsuds and
the overload to the motor. In addition to, this will deteriorate the washing and rinse performmance.