Swann CH1B-2231, CH1B-2237, CH1B-2243, CH1B-2249, CH1B-2255 Series Manual

Cabinet Mount Vanity Tops & Bowls

swanstone.com

m Product Warnings
m Safety Guidelines
m Kit Contents
m Required Tools

m Preparation Tips
m Installation Procedure
m Cleaning & Maintenance
m Surface Repair
m Warranty Information

Models:

Chesapeake Vanity (Single Bowl)
Chesapeake Vanity (Double Bowl)
Contour Vanity (Single Bowl)
Ellipse Vanity (Single Bowl)
Ellipse Vanity (Double Bowl)
Europa Vanity (Single Bowl)

Before Installing

Read and Understand

Form #255-05-16

CAUTION

WARNING

Safety Guidelines

The Swan Assurance — if our product is

properly installed and maintained, as stated in

these instructions, it will not leak.

IMPORTANT NOTICE

IMPORTANT NOTICE: Indicates that equipment or property
damage can result if instructions are not followed.

Remember –

Safety First

IMPORTANT NOTICE

The Swan Corporation, the makers of the
Swan products, cannot anticipate every
possible circumstance that might involve
a potential hazard during the installation
of our product(s). The warnings and
instructions in this installation guide
are, therefore, not all-inclusive. If a tool,
installation procedure, or work method
that is not specifically recommended by
The Swan Corporation is used, you must
satisfy yourself that it is safe. You should
also make sure that the Swan product(s)
will not be damaged by the methods you
choose. The Swan Corporation will not be
held responsible for water damage of any
kind in connection with the installation of
one of our Swan drop-in vanity tops.

Read and Understand the Manual

It is the responsibility of any individual who installs or

maintains this product to fully understand and follow
proper installation and maintenance procedures. Be aware
of the inherent dangers in the use of power tools when
installing this product. Read and understand all Warnings,
Cautions, and Important Notices in this manual.

Work Safely

DO NOT proceed if any doubt arises about the correct

or safe method of performing anything found in this
or other Swanstone manuals. The installation of this product
can require using power tools. Do not use power tools without
adequate training. If necessary, hire or consult a trained
professional for expert assistance before continuing.

Use Proper Tools

Always use proper tools which are in good, working

condition during the installation of the Swanstone
products. Using tools other than those listed could adversely
affect the integrity of floors, pipes, walls, or this product and
could result in water damage or other damage to floors, pipes,
walls, or other portions of your building or home.

Inspect Before Cutting

Make sure no electrical wiring or plumbing is present

before cutting into any surface.

To avoid product damage, personal injury,
or even possible death, carefully read,
understand, and follow all the instructions
in this installation guide before installing
this product(s). Do not use cleaning
fluids or operate power tools unless you
read and understand the instructions
and warnings in this and all other
applicable labels or manuals. Proper use
of tools and the products described in
this guide is your responsibility.

WARRANTY

This product is covered by a Limited
Lifetime Warranty. Refer to the Warranty
section in this manual for complete details.

Save this manual for future
reference.

Important information on cleaning,
maintenance, and repair is contained
within.

CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in injury. It may also be
used to alert against unsafe practices.

Use Proper Installation Methods

Follow all instructions related to vanity tops and bowls

preparation. Failure to follow these instructions could
result in water damage.

Slipping Hazard
Do not install this product in the presence of water.

Installing this product without drying all surfaces, or in
the presence of water, could cause you to slip and fall due to
wet floors or spilled fluids. Personal injury can result from slips
or falls. Before installation, dry all surfaces, including the floor,
with a cloth or paper towel. Clean up all water or spilled fluids
immediately.

Tripping Hazard
Personal injury can result from tripping over power
cords, tools, or other items. DO NOT leave items laying

around the work area.

WARNING

Safety Guidelines

Personal Protection
Be sure to use all personal protective

equipment, such as sturdy work boots,
preferably with steel toes, gloves, and hard hat, if necessary,
to ensure your own safety. To prevent possible damage to
your hearing, always wear ear protection, such as earmuffs or
earplugs, when working around power tools.

Cutting Hazard
The installation of the Swanstone product may require

using power tools. Keep hands away from the cutting
edge of any tool used in the installation of our product. Placing
fingers in or around the cutting blades could result in serious
personal injury.

Sharp Edge Hazard

After cutting the edge of a Swanstone drop-in vanity

top, it can be sharp. Wear protective gloves to prevent
personal injury.

Room Temperature
Allow the Swanstone sink and silicone sealants

to adjust to room temperature for at least six
hours before installation. The product should not be installed at
temperatures below 65°F.

WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in serious injury or
death.

Eye Protection

Be sure to use all personal protective equipment to

ensure your own safety. To avoid eye injury, always
wear protective glasses with side shields when using power
tools. Also, make sure no one else can be injured by flying

particles when using power tools.

Fire Hazard

Personal injury or death can result from a
fire caused by flammable liquids or silicone sealants. Cleaners
or solvents can be highly explosive, resulting in personal
injury or even death, when not used properly. Clean up any
flammable substance immediately. Sparks or open flames can
cause flammable substances to ignite. DO NOT smoke while
working on or near any flammable substance.

Solvents Hazard
Follow all manufacturer’s safety instructions for silicone

sealants and denatured alcohol. Alcohol vapors are
both flammable and hazardous to breathe. Silicone vapors
may irritate eyes and nose. Personal injury can result from
improperly handling or use of products, such as denatured
alcohol. Always follow the manufacturer’s recommendations
for the safe use of these products. Ventilate any work area
before beginning to apply silicone sealants, cleaning agents, or
solvents.

Fumes Hazard
The fumes from the silicone and solvents used

by the installer can be harmful if used in an
unventilated room. Always work in a well-ventilated area. To
keep the area well-ventilated, open windows and use exhaust
fans. If adequate ventilation is not achievable or practical, use
respiratory protective equipment.

800-325-7008

Dust Hazard
When cutting or drilling the Swanstone product,

use a dust collection method which prevents
dust particles from going into the air. Always work in a well­ventilated area. Always use an OSHA approved dust mask
when cutting, drilling, or sanding Swanstone products.

Power Tool Hazard

To prevent personal injury or possible

death, always follow the electrical safety
recommendations of the power tool’s manufacturer. Do not
use power tools in an unsafe manner. Power tools should only
be connected to a circuit protected by a ground-fault circuit
interrupter (GFI).

Shock Hazard

Never use electric power tools around water,

condensation, or other liquids. Electric shock
can cause severe burns, significant injuries, and even death. If
an extension cord is required, always use an OSHA approved
extension cord. Power cords should only be connected to a
circuit protected by a ground-fault circuit interrupter (GFI).

Electrical Shock Hazard

Contacting live electrical wiring with power tools

or hand tools can cause serious injury or death.
Make sure all related circuit breakers are turned OFF. Test for
live circuits or wiring inside any wall where installation of the
Swanstone product requires cutting into a wall.

Electrocution Hazard

Water and other liquids conduct electric current

and can create a short circuit, resulting in
injury or death. Keep all liquids away from electrical cords
and power tools. DO NOT create a short circuit between a
source of electricity and a liquid by being in contact with both
simultaneously.

General Information

Required Tools

mDrill

mScrewdriver

mRuler/Tape Measure

mSafety Glasses

m1/4” Twist Drill and 1-3/8” Hole Saw (Carbide Tipped)

mSilicone

mCaulking Gun

mDust Mask

mDenatured Alcohol

mColor-Matched Silicone Sealant

mConstruction Adhesive (For Undermount Installation)

m3/4” Plywood Cut to 3” Strips (For Undermount Installation)

ADA Applications

These products meet the dimensional requirement to allow
for installation in ADA applications. For up-to-date ADA
regulations, visit www.ADA.gov.

General Information

Sink Contents
Confirm that all parts for the vanity top or bowl have been
included before beginning installation.

Chesapeake Vanity (Single Bowl)

CVSB-01

CH1B-2225 (22-1/2”D x 25”W)
CH1B-2231 (22-1/2”D x 31”W)
CH1B-2237 (22-1/2”D x 37”W)
CH1B-2243 (22-1/2”D x 43”W)
CH1B-2249 (22-1/2”D x 49”W)
CH1B-2255 (22-1/2”D x 55”W)
CH1B-2261 (22-1/2”D x 61”W)

Chesapeake Vanity (Double Bowl)

Contour Vanity (Single Bowl)

CTVSB-01

CV-2225 (22”D x 25”W)
CV-2231 (22”D x 31”W)
CV-2237 (22”D x 37”W)
CV-2243 (22”D x 43”W)
CV-2249 (22”D x 49”W)

Ellipse Vanity (Single Bowl)

CH2B-2261 (22-1/2”D x 61”W)
CH2B-2273 (22-1/2”D x 73”W)

CVDB-01

EVSB-01

VT1B-1719 (17”D x 19”W)
VT1B-1925 (19”D x 25”W)
VT1B-1931 (19”D x 31”W)
VT1B-1937 (19”D x 37”W)
VT1B-2225 (22”D x 25”W)
VT1B-2231 (22”D x 31”W)
VT1B-2237 (22”D x 37”W)
VT1B-2243 (22”D x 43”W)
VT1B-2249 (22”D x 49”W)
VT1B-2255 (22”D x 55”W)
VT1B-2261 (22”D x 61”W)

Ellipse Vanity (Double Bowl)

EVDB-01

VT2B-2261 (22”D x 61”W)

Swan 4 800-325-7008

General Information Installation Procedure

Europa Vanity (Single Bowl)

EUVSB-01

EV-2225 (22-1/2”D x 25”W)
EV-2231 (22-1/2”D x 31”W)
EV-2237 (22-1/2”D x 37”W)
EV-2243 (22-1/2”D x 43”W)
EV-2249 (22-1/2”D x 49”W)
EV-2255 (22-1/2”D x 55”W)
EV-2261 (22-1/2”D x 61”W)

Vanity Top Accessories

Side Splash and Front Apron Panels

Side Splash Panel for Vanity Tops (one per carton)

Model Part Dimensions
VT18-3SS VT01803SS 18” W x 3” H x 3/8”D
VT19-SS VT00019SS 19” W x 3” H x 3/4” D
VT21-3SS VT02103SS 21” W x 3” H x 3/8”D
VT22-SS VT00022SS 22” W x 3” H x 3/4” D

Side Splash Panel for Chesapeake (one per carton)

Model Part Dimensions
CHVTSS CHVTSS 21-5/8” W x 3-1/2” H x 3/4” D

Side Splash Panel for Europa (one per carton)

Model Part Dimensions
EVTSS EV00022SS 21-1/4” W x 3-1/2” H x 3/4” D

Unpack Carton

mUse care when opening the box not to damage the sink.

mThis product is shipped to you or your retail center after
careful inspection. After purchasing the sink, carefully
unpack and inspect the product for any shipping damage
that may have occurred. If damage is found, report it
immediately to the store of purchase. After inspection and
during installation, protect the products from construction
damage, by moving them to another room or area until ready
to install.

mPlease use the model number located on the side of the
box, or the front of this manual, when contacting us with
questions concerning the installation of this unit.

mMake sure the sink is the correct size and in good condition.
Installation of damaged product will void the warranty.

Helpful Hints

mRead these instructions carefully and familiarize yourself
with the various parts of the sink.

mThe variety of installations possible for this sink may require
procedures other than those shown. Ensure construction is
correctly sized, plumb, and square.

mAllow sufficient time for the parts in this sink to adjust to
room temperature. We do not recommend installation of this
product at temperatures below 65 degrees.

mStore unused materials away from the work area to prevent
accidental damage.

mTurn off the hot and cold water supply before starting
installation.

Caulking Tips

mFollow the instructions on the caulking tube.

mWhen job is complete, inspect all caulked areas for gaps
and fill as needed.

mClean up excess silicone using denatured alcohol and a
clean cloth.

mBe very careful not to disturb caulk joints before they dry.

Front Apron Panel (one per carton)

Model Part Dimensions
VT37FA VT02237FA 37” W x 8” H x 1/2” D
VT55FA VT02255FA 55” W x 8” H x 1/2” D
VT1B2261FA VT02261FA 61” W x 8” H x 1/2” D

Side Apron Panel (one per carton)

Model Part Dimensions
VT22SA VT00022SA 21” x 8” x 1/2” D

800-325-7008 5 Swan

Installation Procedure

WARNING

Installation Procedure

Disclaimer

mThe information contained in this Installation Manual is given
free of charge. It is based upon technical data which we
believe to be reliable and is intended for use, by persons
having knowledge of this technical area, at their own
discretion and risk. Swanstone assumes no responsibility
for results obtained or damage incurred from the use of this
material either in whole or in part by the buyer.

mThis manual will give you basic instructions for the
installation of the product in a step-by-step sequence that
will work in most types of installations. If you have an
installation application that is not covered in this manual,
please call your local Swanstone distributor or contact the
Swan Corporation directly for additional information about
your application.

mFollow all installation instructions. Failure to follow these
instructions could result in personal injuries, water damage,
or other damage to floors, pipes, walls, or other portions of
your building or home.

Note: Read All Instructions Before Beginning

Trial Fit

It may be necessary to trim the edge of the vanity top to fit
snugly against the side wall. Install the trimmed edge against
the wall.

Faucet Holes

Note: All Swanstone sinks are manufactured with one

predrilled hole. Optional locations for additional
holes are located on the underside of the sink using
marks (4” and 8”) which are cast into the sink. Follow
Steps 6 and 7 for drilling additional holes to meet the
requirements of the sink faucet or other accessories.

1. If necessary, identify the location of additional holes for the
faucet or other accessories and drill a 1/4” pilot hole from
the back side of the sink.

VI-002

IMPORTANT NOTICE

To prevent damage to the unit, do not use an auger style drill
bit.

VI-003

Breathing Hazard
When cutting or drilling the Swanstone

0” 4” 8”

which prevents dust particles from going into the air. Always

product, use a dust collection method

work in a well-ventilated area. To keep the area well ventilated,
open windows and use exhaust fans. Always use an OSHA
approved dust mask when cutting, drilling, or sanding
Swanstone products.

VI-001

Swan 6 800-325-7008