Swan NWAS1011 Installation & Assembly

TO BE REMOVED FOR USE BY OCCUPANT

Laundry Tubs

MF-1F
(Single Bowl, Floor Mount Metal Legs)

MF-1PF
(Single Bowl, Floor Mount Plastic Legs)

MF-1W (Single Bowl, Wall Mount)

MF-2F

 Product Warnings

(Double Bowl, Floor Mount Metal Legs)

 Safety Guidelines
 General Information
 Installation Procedure
 Cleaning & Maintenance
 Warranty Information

MF-2W (Double Bowl, Wall Mount)

MF-4PF
(Single Bowl, Floor Mount Plastic Legs)

MF-4W (Single Bowl, Wall Mount)

Register your warranty at www.swanstone.com.

Read and Understand

Before Installing

Form #513-3-14-3M

Form # 513-03-12

IMPORTANT NOTICE: Indicates that equipment or property
damage can result if instructions are not followed.

Read and Understand the Manual

It is the responsibility of any individual who installs or

maintains this product to fully understand and follow
proper installation and maintenance procedures. Be aware of
the inherent dangers in the use of power tools when installing
this product. Read and understand all Warnings, Cautions,
and Important Notices in this manual.

Work Safely

DO NOT proceed if any doubt arises about the correct

or safe method of performing anything found in this or
other Swan manuals. The installation of this product can
require using power tools. Do not use power tools without
adequate training. If necessary, hire or consult a trained
professional for expert assistance before continuing.

Use Proper Tools

Always use proper tools which are in good, working

condition during the installation of the Swan products.
Using tools other than those listed could adversely affect the
integrity of floors, pipes, walls, or this product and could result
in water damage, or other damage to floors, pipes, walls, or
other portions of your building or home.

Inspect Before Cutting

Make sure no electrical wiring or plumbing is present

before cutting into a wall.

CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in minor or moderate
injury. It may also be used to alert against unsafe practices.

Lifting Hazard

According to the National Institute for Occupational

Safety and Health, the recommended maximum safe
lifting weight is 51 pounds, with all lifting conditions perfect—
minimal forward reach, steady load close to the body, straight
back, load between knees and shoulders, and good grips. To
avoid personal injury, always use these proper lifting
techniques and use two people to move heavy cartons. Use
appropriate lifting devices to move the load. Always use two
people when lifting heavy or bulky cartons. DO NOT attempt
to lift objects that are too heavy.

WHEN CARRYING A HEAVY LOAD—GET HELP!

Slipping Hazard

Do not install this product in the presence of water.

Installing this product without drying all surfaces, or in
the presence of water, could cause you to slip and fall due to
wet floors or spilled fluids. Personal injury can result from slips
or falls. Before installation, dry all surfaces, including the floor,
with a cloth or paper towel. Clean up all water or spilled fluids
immediately.

Tripping Hazard

Personal injury can result from tripping over power
cords, tools, or other items. DO NOT leave items

laying around the work area.

CAUTION

IMPORTANT NOTICE

The Swan Assurance — if our product is

properly installed and maintained, as stated in

these instructions, it will not leak.

RReemmeemmbbeerr –

–

SSaaffeettyy FFiirrsst

t

The Swan Corporation, the makers of the
Swan products, cannot anticipate every
possible circumstance that might involve
a potential hazard during the installation
of our product(s). The warnings and
instructions in this installation guide are,
therefore, not all-inclusive. If a tool,
installation procedure, or work method
that is not specifically recommended by
The Swan Corporation is used, you must
satisfy yourself that it is safe. You should
also make sure that the Swan product(s)
will not be damaged by the methods you
choose. The Swan Corporation will not be
held responsible for water damage of any
kind in connection with the installation of
one of our Swan bath/shower/panel kits.

To avoid product damage, personal injury,
or even possible death, carefully read,
understand, and follow all the instructions
in this installation guide before installing
this product(s). Do not use cleaning fluids
or operate power tools unless you read and
understand the instructions and warnings
in this and all other applicable labels or
manuals. Proper use of tools and the
products described in this guide is your
responsibility.

WARRANTY

This product is covered by a Limited
Lifetime Warranty. Refer to the Warranty
section in this manual for complete details.

Save this manual for future
reference.

Important information on cleaning,
maintenance, and repair is contained
within.

WARNING

IMPORTANT NOTICE

Safety Guidelines

The Swan Corporation – Swanstone 2 800-325-7008

WARNING

Safety Guidelines General Information

Personal Protection

Be sure to use all personal protective

equipment, such as sturdy work boots,
preferably with steel toes, gloves, and hard hat, if necessary,
to ensure your own safety. To prevent possible damage to
your hearing, always wear ear protection, such as earmuffs or
earplugs, when working around power tools.

Cutting Hazard

The installation of the Swan product may require using

power tools. Keep hands away from the cutting edge
of any tool used in the installation of our product. Placing
fingers in or around the cutting blades could result in serious
personal injury.

WARNING: Indicates a potentially hazardous situation which,
if not avoided, could result in serious injury or death.

Eye Protection

Be sure to use all personal protective equipment to

ensure your own safety. To avoid eye injury, always
wear protective glasses with side shields when using power
tools. Also, make sure no one else can be injured by flying
particles when using power tools.

Fire Hazard

Personal injury or death can result from a

fire caused by flammable liquids or
silicone. Cleaners or solvents can be highly explosive, resulting
in personal injury or even death, when not used properly. Clean
up any flammable substance immediately. Sparks or open
flames can cause flammable substances to ignite. DO NOT
smoke while working on or near any flammable substance.

Solvents Hazard

Follow all manufacturer’s safety instructions for silicone

and denatured alcohol. Alcohol vapors are both
flammable and hazardous to breathe. Silicone vapors may
irritate eyes and nose. Personal injury can result from
improperly handling or use of products such as denatured
alcohol. Always follow the manufacturer’s recommendations for
the safe use of these products. Ventilate any work area before
beginning to apply silicone, cleaning agents, or solvents.

Fumes Hazard

The fumes from the silicone and solvents used
by the installer can be harmful if used in an

unventilated room. Always work in a well-ventilated area.

Power Tool Hazard

To prevent personal injury or possible death,

always follow the electrical safety
recommendations of the power tool’s manufacturer. Do not
use power tools in an unsafe manner. Power tools should only
be connected to a circuit protected by a ground-fault circuit
interrupter (GFI).

Electrical Shock Hazard

Contacting live electrical wiring with power tools

or hand tools can cause serious injury or death.
Make sure all related circuit breakers are turned OFF. Test for
live circuits or wiring inside any wall where installation of the
Swan product requires cutting into a wall.

Electrocution Hazard

Water and other liquids conduct electric current

and can create a short circuit, resulting in injury
or death. Keep all liquids away from electrical cords and
power tools. DO NOT create a short circuit between a source
of electricity and a liquid by being in contact with both
simultaneously.

General Information

A laundry tub or utility sink can be a useful addition to any home
to soak dirty clothes, wash the dog, or clean large, odd-shaped
household goods. Our laundry tubs are made from Veritek,
which makes them easy to install and maintain. Our Veritek
material has no surface coating to chip or crack and will not
mold or mildew. The laundry tubs can also be secured to the
wall or the floor as a precaution to prevent unwanted tipping.

The installation process is straightforward and most
homeowners can easily complete the task. The hardest part of
the job, if necessary, may be installing the water lines and
drain pipe. Always check local building codes to verify that
you, the homeowner, can install the plumbing yourself.

A laundry tub is an easy project to install and requires very few
special tools. Followed carefully, these installation instructions
will result in an easy, trouble-free installation of your Swan
Corporation product. Any deviations, additions, and/or deletions
from the prescribed installation, without prior written approval of
our Customer Relations Department, will void the warranty
covering this product. Not following the directions could also
result in personal injuries, water damage, and other damage to
floors, pipes, walls, and other portions of your building or home.

• Read all instructions completely before beginning

installation.

• Check all local plumbing codes.

• Be sure to shut off the water at the source before

starting installation.

Contents (Floor Mount Units)

 Laundry Tub

 Four Metal Angular Legs

Four Metal Angular Legs or Four Plastic Angular Legs

 Leveling Brackets (Qty 4)

 Flat Head Screws (Qty 4)

 Nuts (Qty 4)

Shock Hazard

Never use electric power tools around water,

condensation, or other liquids. Electric shock can
cause severe burns, significant injuries, and even death. If an
extension cord is required, always use an OSHA approved
extension cord. Power cords should only be connected to a
circuit protected by a ground-fault circuit interrupter (GFI).

800-325-7008 3 The Swan Corporation – Swanstone

LT-031

General Information Installation Procedure

 Please use the model number located on the side of the

box when contacting us with questions concerning the
installation of this product.

Helpful Hints

 Read all instructions carefully BEFORE starting the

installation. Familiarize yourself with the various parts of
the kit.

 Store unused materials away from the work area to prevent

accidental damage.

 If the product is placed over a garage or on an outside wall,

care must be taken to ensure that the shower plumbing is
properly insulated from cold temperatures.

Disclaimer

 The information contained in this Installation Instruction is

given free of charge. It is based upon technical data which
we believe to be reliable and is intended for use, by
persons having knowledge of this technical area, at their
own discretion and risk. The Swan Corporation assumes
no responsibility for results obtained or damage incurred
from the use of this material either in whole or in part by the
buyer.

 This manual will give you basic step-by-step instructions for

the installation of the product that will work in most types of
installations. If you have an installation application that is
not covered in this manual, before beginning the
installation, please call your local Swan distributor or
contact the Swan Corporation directly for additional
information about your application.

 Follow all installation instructions. Failure to follow these

instructions could result in personal injuries, water damage,
or other damage to floors, pipes, walls, or other portions of
your building or home.

Quick Reference Assembly

1. Prior to installation of the laundry tub, first attach the legs
to floor mount models (Step 1a) or attach the filler
brackets to the wall mount models (Step 1b). Refer to the
specific section in this manual for detailed instructions.

2. Attach the wall mounting plate to the wall. (Step 2a, 2b, or
2c).

3. Finally, install faucet and P-trap onto the laundry tub.

4. Install laundry tub.

5. Anchor floor mount units to the floor (optional).

6. Install splash guard (optional).

1. Attach Legs / Filler Brackets

1a. Attach Metal Legs — MF-1F and

MF-2F (Single and Double Bowl Models)

1. Place the laundry tub upside down on a flat surface.

Contents (Wall Mount Units)

 Laundry Tub

 Filler Brackets (Right and Left)

 Filler Bracket Mounting Screw (Qty 2)

 Wall Mounting Plate

 Screws for Wall Mounting Plate (Qty 3 or 6)

 Wall Anchors for Wall Mounting Plate (Qty 3 or 6)

 Please use the model number located on the side of the

box when contacting us with questions concerning the
installation of this product.

Helpful Hints

 Read all instructions carefully BEFORE starting the

installation. Familiarize yourself with the various parts of
the kit.

 Store unused materials away from the work area to prevent

accidental damage.

 If the product is placed over a garage or on an outside wall,

care must be taken to ensure that the shower plumbing is
properly insulated from cold temperatures.

Disclaimer

 The information contained in this Installation Instruction is

given free of charge. It is based upon technical data which
we believe to be reliable and is intended for use, by
persons having knowledge of this technical area, at their

General Information Installation Procedure

Contents (Wall Mount Units)

 Laundry Tub

 Filler Brackets (Right and Left)

 Filler Bracket Mounting Screw (Qty 2)

 Wall Mounting Plate

 Screws for Wall Mounting Plate (Qty 3 or 6)

 Wall Anchors for Wall Mounting Plate (Qty 3 or 6)

Washers (Qty 2)

Purchased Items

 Faucet

 Flexible Hot and Cold Water Supply Lines

 PVC Trap Kit

 PVC Tailpiece

 1/4” x 1-1/2” Tapcon Screws (optional for wall mount units

only - for concrete wall installation)

 Floor Anchors and Bolts (optional)

Required Tools and Safety Equipment

 Safety Glasses

 Hearing Protection

 Hammer

 Adjustable Pliers

 Adjustable Wrench

 Phillips Screwdriver

 Flat Blade Screwdriver

 Tape Measure

 Hacksaw (Cutting tail piece to length)

 Level

 Hammer Drill and Carbide Drill Bit (for wall mount

installation into concrete or to fasten the legs to the floor)

Unpackaging

 Use care when opening the box so that you do not damage

the product.

 This product is shipped to you or your retail center after

careful inspection. After purchasing the product, carefully
unbox and inspect the product for any shipping damage that
may have occurred. If damage is found, report it
immediately to the store of purchase. Installation of a
damaged product will void the warranty.

 Make sure the product is the correct size and confirm that

all parts have been included before beginning installation.

 Floor mount models are shipped with four legs and leveling

hardware. The floor mount models DO NOT have right and
left side filler brackets like the wall mount models.

The Swan Corporation – Swanstone 4 800-325-7008

LT-032

LT-032

 Please use the model number located on the side of the

box when contacting us with questions concerning the
installation of this product.

Helpful Hints

 Read all instructions carefully BEFORE starting the

installation. Familiarize yourself with the various parts of
the kit.

 Store unused materials away from the work area to prevent

accidental damage.

 If the product is placed over a garage or on an outside wall,

care must be taken to ensure that the shower plumbing is
properly insulated from cold temperatures.

Disclaimer

 The information contained in this Installation Instruction is

given free of charge. It is based upon technical data which
we believe to be reliable and is intended for use, by
persons having knowledge of this technical area, at their
own discretion and risk. The Swan Corporation assumes
no responsibility for results obtained or damage incurred
from the use of this material either in whole or in part by the
buyer.

 This manual will give you basic step-by-step instructions for

the installation of the product that will work in most types of
installations. If you have an installation application that is
not covered in this manual, before beginning the
installation, please call your local Swan distributor or
contact the Swan Corporation directly for additional
information about your application.

 Follow all installation instructions. Failure to follow these

instructions could result in personal injuries, water damage,
or other damage to floors, pipes, walls, or other portions of
your building or home.

Quick Reference Assembly

1. Prior to installation of the laundry tub, first attach the legs
to floor mount models (Step 1a) or attach the filler
brackets to the wall mount models (Step 1b). Refer to the
specific section in this manual for detailed instructions.

2. Attach the wall mounting plate to the wall. (Step 2a, 2b, or
2c).

3. Finally, install faucet and P-trap onto the laundry tub.

4. Install laundry tub.

5. Anchor floor mount units to the floor (optional).

6. Install splash guard (optional).

1. Attach Legs / Filler Brackets

1a. Attach Metal Legs — MF-1F and

MF-2F (Single and Double Bowl Models)

1. Place the laundry tub upside down on a flat surface.

Attach Plastic Legs - MF-4W (Single Bowl Model)

Protect the top edges of the laundry tub from scratches or
other damage by placing cardboard or other scratch

Protect the top edges of the laundry tub from scratches or

resistant material on the floor.

other damage by placing cardboard or other scratch
resistant material on the floor.

LT-001

Slide the metal or plastic leg into one of the plastic corner

2.

2. Slide the metal leg into one of the plastic corner retaining

retaining sockets in the bottom of the laundry tub. All four

sockets in the bottom of the laundry tub. All four legs are

legs are identical and can be installed in any one of the

identical and can be installed in any one of the four corners.

four corners.

LT-002

Installation Procedure

1b. Attach Filler Brackets and Wall Mount —

MF-1W and MF-2W (Single and Double Bowl
Models)

1. Place the laundry tub upside down on a flat surface.
Protect the top edges of the laundry tub from scratches or
other damage by placing cardboard or other scratch
resistant material on the floor.

2. Find the right-side filler bracket. Install it with the end of
the filler bracket fitted between the outside of the sink and
guide posts (1). Also place the filler bracket over guide
post (2) and the screw hole in the bottom of the laundry
tub.

MF-4W (Single Bowl Model)

LT-018

3. Place a block of scrap wood over the end of the leg and
drive the leg down into the socket with a hammer.

LT-003

4. Install the other three legs in the same manner.

5. Install one leg leveler on each leg using the screw and nut
included with each unit. Do not completely tighten the
screws until the laundry tub is in its final location and can
be leveled.

2

1

LT-019

3. If you have the MF-4W wall mount assembly: Using a flat

3. Using a flat blade screwdriver, install one panhead screw

blade screwdriver, install one panhead screw and washer

to hold the filler bracket in place. Do not overtighten the

to hold the filler bracket in place. Do not overtighten the

screw.

screw.

LEG LEVELER

SCREW

NUT

LT-020

4. Install the left-side filler bracket in the same manner.

LT-004

800-325-7008 5 The Swan Corporation – Swanstone

Installation Procedure

2. Attach Wall Mounting Plate

2a. Attach Wall Mounting Plate to Framed Walls

1. Locate the rough position of the laundry tub and then
locate the wall studs. The mounting plate must be
attached using at least three screws.

LT-021

If only two screws can be used, install cross blocking
(2” x 6”) between the studs and then attach the wall mounting
plate. Again, for double sinks install cross blocking (2” x 6”)
between the studs to add extra support for the wall mounting
plate and the sink.

Note: Trial fit the wall mounting plate to the laundry tub. If the

mounting plate is too long, break off the left side of the
wall mounting plate by snapping it along the plate’s
scored ridge.

LT-024

3. Position the top lip of the wall mounting plate on the mark.
Be sure you mark the mounting holes over the
studs/cross-blocks. Use a bubble level to make sure the
wall mounting bracket is level.

2. Determine the comfortable working height of the top of the
sink. This height may vary depending on your application;
however, a typical dimension is 32” up from the floor. Use a
level to mark a line 1” below the desired height on the wall.

LT-025

4. Drill a 1/8” pilot hole into the wood and attach the
mounting plate to the wall with at least three 1/4" x 1-1/2"
long zinc hex head lag screws. Tighten the screws with a
Phillips screwdriver.

Note: On double bowl models use at least six screws to

attach the wall mounting bracket to the wall.

2b. Attaching Wall Mounting Plate to Concrete

or Block Walls with Plastic Wall Anchors

There are two methods to install the mounting plate onto a
concrete or block wall; Step 2b) a plastic wall anchor with a lag
screw, or, Step 2c) Tapcon concrete screws. The tapcon
screws for mounting the wall mounting plate to concrete are not
supplied with the product and must be purchased separately.

1. Locate the height of the wall mounting plate in the same
manner as with wood construction (Step 2a).

Note: Trial fit the wall mounting plate to the laundry tub. If the

wall mounting plate is too long, break off the left side of
the wall mounting plate by snapping it along the plate’s
scored ridge.

31”

LT-023

The Swan Corporation – Swanstone 6 800-325-7008

LT-024

Oversized pilot holes may make it impossible to properly

WARNING

WARNING

set the anchor and will reduce the anchor's load (holding)
capacity. This reduced holding capacity can result in the
anchor pulling free from the wall, resulting in possible
personal injury or even death.

2. Drill a 5/16” pilot hole two inches into the concrete or block
wall using a masonry bit and a hammer drill. Clean out
the hole with a vacuum sweeper.

Note: In concrete block walls do not drill the anchor holes into

the mortar joints. These joints typically do not have the
same holding strength as the block itself.

2”

Installation Procedure

2c. Attaching Wall Mounting Plate to Concrete

or Block Walls with Tapcon Wall Anchors
(User Supplied)

1. Locate the wall mounting plate in the same manner as
with wood construction.

Note: Trial fit the wall mounting plate to the laundry tub. If the

wall plate is too long, break off the left side of the wall
mounting plate by snapping it along the plate’s scored
ridge.

LT-024

LT-026

3. Insert the plastic anchor into the hole and drive it in until it
is flush with the wall surface. For single bowl models use
at least three anchors. For double bowl models use at
least six anchors.

LT-027

4. Attach the mounting plate to the wall with 1/4" x 1-1/2"
long Phillips head screws (supplied with unit). For single
bowl models use at least three screws. For double bowl
models use at least six screws.

Note: Make sure the wall mounting plate is straight,

regardless of the wall contour, before completely
tightening the screws. If the wall is not flat, shim behind
the mounting plate, as needed.

Oversized holes may make it impossible to properly hold
the Tapcon screw and will reduce the load (holding)
capacity. This reduced holding capacity can result in the
screw pulling free from the wall, resulting in possible
personal injury or even death.

2. Drill a 3/16" pilot hole into the wall using a masonry bit
and hammer drill.

Note: Always follow the mounting hardware manufacturer’s

recommendation for installation of their mounting
hardware.

3. Attach the mounting plate to the wall with 1/4" x 1-1/2"
long Tapcon Hex Head Masonry Screws. Do not
overtighten the screws. For single bowl models use at
least three screws. For double bowl models use at least
six screws.

LT-029

Note: Make sure the wall mounting plate is straight,

regardless of the wall contour, before completely
tightening the screws. If wall is not flat, shim behind the
mounting plate, as needed.

3. Installing the Faucet and Drain

1. Shut off the water supply to the entire house or at the
location of the old sink.

LT-028

800-325-7008 7 The Swan Corporation – Swanstone

2. Release the pressure and drain the water lines by turning
on a faucet in the lowest part of the house. Turn on both
the hot and cold water faucets.

Installation Procedure

3. If replacing an existing laundry tub, loosen and remove the
hot and cold water lines and waste pipe connections. Use
a container to catch any water remaining in the P-trap.

Note: If the P-trap and water lines are in poor condition,

replace them with new parts. Also replace any rusted
or corroded fittings with new parts. The faucet can be
reused and reinstalled.

4. Install the faucet assembly according to the
manufacturer’s instructions (homeowner supplied).

LT-006

Note: Preinstallation of the faucet, supply lines, and P-trap are

easier when the laundry tub is not against and/or
attached to the wall.

5. Attach the two flexible water lines onto the faucet
(homeowner supplied). Do not over-tighten the connections.

LT-007

4. Final Installation

1. For models with legs, place the laundry tub where it will be
installed. For wall mount models, hang the sink onto the
wall mounting plate (see Step 2).

LT-009

2. On wall mount models only, lift and place the sink over the
wall mounting plate. Make sure the laundry tub is seated
securely into the lip of the wall mounting plate.

6. Assemble the PVC trap components (homeowner supplied)
and attach them to the drain hole(s) in the laundry tub.

LT-030

3. Attach the PVC tailpiece (homeowner supplied) to the
drain pipe. Cut the tailpiece to the proper length using a
hacksaw, if necessary. Use sandpaper or a file to remove
any burrs or sharp edges.

LT-008

LT-010

LT-008b

The Swan Corporation – Swanstone 8 800-325-7008

4. Attach the flexible water supply lines to the water shut off

WARNING

valves. The threaded ends of the water lines can be
wrapped with Teflon pipe tape to ensure a tight, leak-proof
seal. Tighten the fitting with a wrench but do not over­tighten.

Installation Procedure

LT-014

5. Floor Anchors

LT-011

5. The water lines and waste pipes should now be
completely installed.

LT-012

6. Slowly turn ON the hot and cold water shut off valves.
Turn the faucets ON and flush the water lines to remove
any debris that may be in the water line or the drain pipe.

A laundry tub(s) that is full of water can weigh from 175 to
350 pounds and could tip over if someone pulls against it,
causing personal injuries, death, and/or damage to your
home. Securing the legs to the floor will help prevent
unwanted tipping.

1. As added protection against unwanted tipping of floor
model laundry tubs, secure the unit to the floor using
homeowner supplied anchors.

LT-015

2. Adjust the four leveling feet on the legs. A slight angle
(front to back) toward the drain will eliminate water from
standing in the bottom of the laundry tub.

LT-013

7. Check all water lines and waste connections for leaks.
Tighten the connection if a leak appears. Do not over­tighten.

800-325-7008 9 The Swan Corporation – Swanstone

LT-017

Care and Cleaning Warranty

6. Splash Guard

As an added precaution to water splatter and/or damage to the
wall behind the sink, you can install a piece of 1/8” plastic onto
the wall. You can also caulk the area where the plastic meets
the edge of the laundry tub.

LT-016

Care and Cleaning

Swan products are stain and wear resistant; however, the
finish requires reasonable care.

Maintenance And Cleaning

Everyday cleaning with liquid cleaners such as Dow or Lysol
foaming bubbles, Top Job, Mr. Clean or similar type products
with a sponge or Mr. Clean Magic Eraser. To remove hard
water stains or mineral build-up, scale removers such as Lime
Away, Rust-out or Whink are recommended. Do not use
abrasive cleaners or pads such as Ajax, Comet, SOS, Brillo or
other similar metal scouring pads.

Because cleaning products change over time, always check
the manufacturer’s instructions to make sure it is compatible
with plastic. DO NOT use a cleaner if the label indicates it
should not be used on plastics. DO NOT use spray-on
cleaners that require daily use without immediately rinsing with
water to stop the chemical cleaning reaction because damage
will result and void the warranty.

IMPORTANT NOTICE

Because cleaning products change over time, always check
the manufacturer’s instructions to make sure it is compatible
with plastic. DO NOT use a cleaner if the label indicates it
should not be used on plastics. DO NOT use spray-on
cleaners that require daily use without immediately rinsing with
water to stop the chemical cleaning reaction because damage
will result and void the warranty.

Day-To-Day Cleanup

Simply wipe the surfaces with a clean towel to remove
watermarks and residues. This Swan Corporation product can
be cleaned with warm water, a soft cloth, and normal
(nonabrasive) household detergents or cleansers, such as
Fantastic, Formula 409, Clorox Clean-up, Handy Andy, Mr.
Clean, or Lestoil. Always rinse off cleaners within five minutes
of application.

If necessary, use a nonabrasive cleaner with a nylon brush or
pad to remove build-up on the shower floor surface. Do Not
use abrasive cleansers, steel wool, or a wire brush. This will
damage the surface.

Caulking Joints

If silicone caulking was applied at installation, inspect the
caulking joints monthly for damage or any signs of separation
from the mating surface. Cracks in the caulking will allow
water to leak into the surrounding surfaces. Reapply caulking

to any joint showing signs of wear or cracking.

Warranty

If a Swan product covered by this warranty is found to be
defective in materials or workmanship, after inspection by an
authorized Swan Corporation representative, we will repair, or
at our option, exchange the product for a similar model. This
warranty extends for a designated period of time, so long as it
remains in use in its original place of installation.

This warranty covers products installed in accordance with the
Swan Corporation’s installation instructions, used as
recommended, and not damaged due to misuse, abuse, or
improper installation. It does not apply to any seams or
changes made to the product by professional tradesmen or
fabricators.

The Swan Corporation’s option to repair or exchange the
products under this warranty does not cover any labor or other
costs of removal or installation, nor shall the Swan Corporation
be responsible for any other incidental or consequential
damages attributable to a product defect or to the repair or
exchange of a defective product.

Residential 1-Year Limited Warranty

The warranty applies only to the original purchaser and
installation of these products in residential applications. It
does not apply to commercial applications.

Commercial 1-Year Limited Warranty

The warranty applies only to the original purchaser and
installation of these products in commercial applications.

The Swan Corporation – Swanstone 10 800-325-7008

Save these Installation Instructions for future reference. They provide

important information on cleaning and maintenance of the Swan Corporation

Laundry Tub.

www.swanstone.com

Form #513-3-14-3M

Form # 513-03-12