SVAT Electronics S400 User Manual

4 Indoor Camera Surveillance System

User's Manual

Système D'intérieur de Surveillance
de Caméra Quatre.

Le Manuel D'Utilisateur

www.svat.com

Clearvu S400

www.svat.com

INCLUDED IN THIS SYSTEM:

1. 4 Input Switcher

2. Remote Controller

3. 4 x Color Camera With Mounting bracket

4. 4 x 30ft of 4 PIN DIN cable

5. A/V cable

6. 10V 600mA AC/DC Adaptor

PARTS OF THE SWITCHER

1. Power indication LED

2. Setting indication LED

3. Mute indication LED

4. Channel display LED

5. Power ON / OFF button

6. Setting button

7. Mute button

8. Storage button

9. Channel scan button

10. Channel down button

11. Channel up button

12. Scan time adjustment

13. Output jack to Monitor or TV A/V input
14~17. Camera input jacks

18. Adapter jack

PARTS OF THE CAMERA

A. Camera with built-in microphone
B. Mounting bracket

PARTS OF THE REMOTE CONTROLLER

1. MUTE button

2. SCAN button

3. Channel down button

4. Channel up button

1

2

3

4

5

6

7

8

9

10

11

12 13 14 15 16 17 18

A

B

4

3

2

1

www.svat.com

INSTALLATION AND ADJUSTMENT

A. CAMERA INSTALLATION

1. Install or mount the camera at the desired indoor location. Do not
place camera in a location subject to direct sunlight or bright light.

2. The coaxial cable supplied has one end with a DIN connector (Male)
and the opposite end with a DIN connector(Female). Slowly insert the
DIN plug into the back of the camera being careful to align the DIN
plug correctly.

B. SWITCHER INSTALLATION

1. Connect the power adapter to the DC IN jack on the back of the
switcher and connect the other end to a wall outlet.

2. Connect the output jack to your TV/VCR using the supplied cable.

3. Connect the CAM 1~4 DIN jack to the back of each camera.

4. After connecting all the cameras, press the power button, the
power indication LED will light up and indicating camera number on
channel display LED.

TV/VCR

DC IN

12V ADAPTER

VIDEO IN

AUDIO IN

www.svat.com

OPERATING PROCEDURE

A. SETTING UP CHANNELS ON SWITCHER

If you would like to view more then one camera on your screen, each
channel has to be stored in the switcher by the following procedure. Each
channel indicates one camera and displays the image of corresponding
camera.

1. Press [Set], setting indication LED will light up

2. Press channel select button, then press [Store] when channel display
LED indicates 1.

3. Press channel select button, then press [Store] when channel display
LED indicates 2.

4. Press channel select button, then press [Store] when channel display
LED indicates 3.

5. Press channel select button, then press [Store] when channel display
LED indicates 4.

6. Press [Set] again when completed [1] ~ [5].

B. AUTO SWITCH FUNCTION

1. Press[Scan] button, the switcher will scan each preset camera

2. The scanning time is adjustable from 1 sec. to 30 sec. Use flat head
screwdriver to adjust the scan time period by turning the tuner
(no. 12 in the switcher parts list).

C. SINGLE CHANNEL SELECTION

1. Setting the scan channel according to the number of the camera
(procedure A). That is if the camera is No. 1, the switcher also has to
be on channel 1.

2. Use the channel selection button up/down to select desired camera
[Indicated by LED display]
Note: The single channel selection automatically stops the
auto-switch function.

D. MUTING

Push [Mute] button to stop audio transmission, and again to resume sound.

E. REMOTE CONTROLLER OPERATING :

1. Press [Scan] button, LED indicator will light up, channel scan
function starts.

2. You can select single channel monitoring by pressing [channel up]
button (LED indicator will light up, the Switcher Channel will up 1
channel) or [channel down] button (LED indicator will light up, the
Switcher Channel will down 1 channel) for channel selection. Please
note, this selection automatically stops the auto-scan function.

3. Push [Mute] button, the LED indicator will light up), to stop audio
transmission, and again to resume sound.