Suzuki Marine DF40A, DF50A, DF50AV, DF60A, DF60AV Owner's Manual
DF40A
DF50A
DF50AV
DF60A
DF60AV
OWNER’S MANUAL
EN
ENGLISH
1
IMPORTANT
WARNING/ CAUTION/ NOTICE/
Please read this manual and follow its instructions carefully. To emphasize special information, the symbol and the words WARNING,
CAUTION, NOTICE and NOTE have special
meanings. Pay special attention to the messages highlighted by these signal words.
WARNING
Indicates a potential hazard that could
result in death or serious injury.
CAUTION
Indicates a potential hazard that could
result in minor or moderate injury.
NOTICE
Indicates a potential hazard that could
result in damage to the motor or boat.
NOTE:
Indicates special instructions to make maintenance easier or instructions clearer.
BREAK-IN INFORMATION
FOR YOUR OUTBOARD MOTOR
The first 10 hours are the most important in the
life of your engine. Proper operation during this
break-in period is essential to help ensure maximum life and performance.
Refer to the BREAK-IN section of this manual
for specific break-in recommendations.
IMPORTANT NOTICE TO OWNERS
WARNING
Failure to take the proper precautions
may increase the risk of death or severe
injury to you and your passengers.
• Prior to first-time use of your outboard
motor, familiarize yourself thoroughly
with the contents of this owner’s manual. Be aware of all outboard motor features and all safety and maintenance
requirements.
NOTE
• Inspect the boat and motor before each
trip. See the INSPECTION BEFORE
BOATING section for important items.
• Become thoroughly familiar with all
operating and handling characteristics
of your boat and motor. Practice at low
and moderate speeds until you are
competent at handling the boat and
motor. Do not attempt to operate at maximum performance until you are completely familiar with all of these
characteristics.
• Carry boating safety and emergency
equipment. This important equipment
includes; flotation aids for each person
(plus one throwable buoyant cushion in
any boat 16 feet or longer), fire extinguisher, sound signaling device, visual
distress signals, anchor, bilge pump,
bucket, compass, emergency starter
rope, extra fuel and oil, first aid kit,
flashlight, food and water, mirror, paddles, tool kit, and transistor radio. Be
sure you are carrying the equipment
appropriate for your trip before launching.
• Never start the engine or let it run
indoors or where there is little or no
ventilation. Exhaust gas contains carbon monoxide, a gas that is colorless
and odorless and can cause death or
severe injury.
• Instruct your passengers on how to
operate the boat, how to deal with
emergencies, and how to operate
safety and emergency equipment.
• Do not hold onto the motor cover or
any other parts of your outboard motor
while getting on or off your boat.
• Ensure that everyone wears a life jacket
on board.
• Never operate the boat while under the
influence of alcohol or other drugs.
• Distribute all weight load evenly in the
boat.
• Have all scheduled maintenance performed. Consult your authorized
Suzuki marine dealer as required.
2
• Do not modify or remove any outboard
motor standard equipment. To do so
may make the motor unsafe to use.
• Learn and obey all applicable navigation rules.
• Pay attention to all weather forecasts.
Do not set out if weather is unsettled.
• Use extreme caution when purchasing
replacement parts or accessories.
Suzuki strongly recommends that you
use only genuine Suzuki replacement
parts/accessories or their equivalent.
Inappropriate or poor quality replacement parts or accessories can create
unsafe operating conditions.
NOTE:
Mounting radio transceiver or navigational
equipment antennae too close to the engine
cowling can cause electrical noise interference.
Suzuki recommends that antennae be mounted
at least one meter (40 inches) away from the
engine cowling.
This manual should be considered a permanent part of the outboard motor and
should remain with the outboard motor
when resold or otherwise transferred to a
new owner or operator. Please read this
manual carefully before operating your
new Suzuki and review the manual from
time to time. It contains important information on safety, operation, and maintenance.
FOREWORD
The proper care and maintenance that your
outboard motor requires is outlined in this manual. By following these instructions explicitly you
will ensure a long trouble-free operating life for
your outboard motor. This outboard motor also
conforms to the U.S Environmental Protection
Agency emission regulations which apply to
new outboard motors. The proper adjustment of
engine components is necessary for this outboard motor to comply with the EPA regulations. Therefore, please follow the maintenance
instructions closely to ensure emission compliance. Your Suzuki dealer has experienced technicians that are trained to provide your outboard
motor with the best possible service with the
right tools and equipment.
All information in this manual is based on the
latest product information available at the time
of publication. Due to improvements or other
changes, there may be discrepancies between
this manual and your outboard motor. Suzuki
reserves the right to make production changes
at any time, without notice and without incurring
any obligation to make the same or similar
changes to outboard motors previously built or
sold.
3
PLEASE PRESERVE NATURE
Protect and preserve your boating waters and
their land access. Never pollute the water or
land with oil, gas, or other harmful products. For
example, make sure you dispose of used gear
oil properly following a gear oil change. Also
remember not to litter. With a little bit of effort,
our boating waters can be enjoyed for many
years to come.
Suzuki Motor Corporation believes in conservation and protection of Earth’s natural resources.
To that end, we encourage every outboard
motor owner to recycle, trade in, or properly dispose of, as appropriate, used oil and batteries.
TAKE A BOATING SAFETY CLASS
An educated boater will enjoy boating more and
will be a safer boater. We recommend that you
take a boating safety class.
Classes explaining required and recommended
equipment for small boats and offering training
in good seamanship are conducted by the U.S.
Coast Guard Auxiliary, the U.S. Power Squadron, and many Red Cross chapters. For information on classes in your area, call toll-free 1800-336-BOAT (2628).
Your state’s department of boating and your
Suzuki Marine dealer can supply you with additional information on boating safety and regulations, or you can call the U.S. Coast Guard
Boating Safety Hotline toll-free at 1-800-368-
5647.
California Proposition 65 Warning
WARNING
Engine exhaust, some of its constituents,
and certain product components contain
or emit chemicals known to the State of
California to cause cancer and birth
defects or other reproductive harm.
4
TABLE OF CONTENTS
FUEL AND OIL....................................... 6
GASOLINE............................................ 6
FILLING THE FUEL TANK ................... 7
ENGINE OIL.......................................... 8
GEAR OIL ............................................. 8
LOCATION OF SAFETY LABELS ..... 9
LOCATION OF PARTS....................... 10
MOTOR INSTALLATION.................. 12
BATTERY INSTALLATION .............. 12
BATTERY REQUIREMENT ................ 12
BATTERY INSTALLATION ................ 13
USE OF ELECTRICAL
ACCESSORIES...................................
PROPELLER SELECTION AND
INSTALLATION................................... 14
PROPELLER SELECTION ................. 14
PROPELLER INSTALLATION ........... 15
ADJUSTMENTS.................................... 15
TRIM ANGLE ADJUSTMENT............. 15
TRIM TAB ADJUSTMENT.................. 17
THROTTLE TENSION
ADJUSTMENT ....................................
IDLE SPEED ADJUSTMENT.............. 17
SETTING OF TILT UPPER LIMIT
POSITION <DF50AV/60A/60AV>.......
MOTOR COVER FASTENING
ADJUSTMENT ....................................
CAUTION SYSTEM............................. 19
INDICATOR CHECK........................... 20
OVER-REVOLUTION CAUTION
SYSTEM..............................................
OIL PRESSURE CAUTION
SYSTEM..............................................
COOLING WATER CAUTION
SYSTEM..............................................
BATTERY VOLTAGE CAUTION
SYSTEM..............................................
DIAGNOSTIC SYSTEM...................... 23
OIL CHANGE REMINDER
SYSTEM................................................. 24
SYSTEM ACTIVATION....................... 24
CANCELLATION ................................ 24
ENGINE STALLING CAUTION
SYSTEM................................................. 25
OPERATION OF TILTING
SYSTEMS............................................... 25
POWER TRIM AND TILT.................... 25
MANUAL TILTING .............................. 26
TILT LEVER ........................................ 26
INSPECTION BEFORE BOATING... 27
BREAK-IN ............................................. 29
14
17
18
19
20
21
21
23
OPERATION......................................... 30
BEFORE ATTEMPTING TO START
THE ENGINE.......................................
STARTING THE ENGINE ................... 32
EMERGENCY STARTING .................. 34
SHIFTING AND SPEED CONTROL ... 36
STOPPING THE ENGINE ................... 37
MOORING ........................................... 38
OPERATION IN SHALLOW
WATER................................................
OPERATING THE TROLL MODE
(Optional Item) ...................................
OPERATION IN SALT WATER .......... 39
OPERATION IN FREEZING
WEATHER...........................................
30
38
38
39
MOTOR REMOVAL AND
TRANSPORTING................................. 40
MOTOR REMOVAL ............................ 40
MOTOR TRANSPORTING.................. 40
TRAILERING ....................................... 42
INSPECTION AND
MAINTENANCE................................... 43
MAINTENANCE SCHEDULE ............. 43
SPARK PLUG ..................................... 45
BREATHER AND FUEL LINE ............ 47
ENGINE OIL........................................ 47
GEAR OIL ........................................... 49
LUBRICATION.................................... 50
CORROSION PREVENTION .............. 50
ANODES.............................................. 50
BONDING WIRES ............................... 51
BATTERY............................................ 51
ENGINE OIL FILTER .......................... 52
FUEL FILTER...................................... 52
FLUSHING THE WATER
PASSAGES............................................. 53
SUBMERGED MOTOR....................... 55
STORAGE PROCEDURE ................... 56
MOTOR STORAGE............................. 56
BATTERY STORAGE......................... 57
AFTER STORAGE ............................... 57
GENERAL INFORMATION............... 57
WARRANTIES (For U.S.A)................. 57
IDENTIFICATION NUMBER
LOCATION..........................................
58
EMISSION CONTROL
INFORMATION.................................... 58
TROUBLESHOOTING........................ 58
SPECIFICATIONS ............................... 60
CHART OF TOTAL OPERATING
HOURS INDICATION ......................... 61
FLOWCHART OF OIL CHANGE
REMINDER SYSTEM.......................... 61
5
FUEL AND OIL
GASOLINE
Suzuki highly recommends that you use alcohol-free unleaded gasoline whenever possible,
with a minimum pump octane rating of 87
((R+M)/2 method). In some areas, the only
fuels that are available are oxygenated fuels.
Oxygenated fuels which meet the minimum
octane requirement and the requirements
described below may be used in your outboard
motor without jeopardizing the New Outboard
Motor Limited Warranty.
NOTICE
Use of leaded gasoline can cause engine
damage. Use of improper or poor quality
fuel can affect performance and may
damage your motor and fuel system.
Use only unleaded gasoline. Do not use
fuel having lower than the recommended
octane, or fuel that may be stale or contaminated by dirt/water etc.
NOTE:
Oxygenated fuels are fuels which contain oxygen-carrying additives such as MTBE or alcohol.
Suzuki recommends that you install a waterseparating fuel filter assembly between your
boat’s fuel tank(s) and outboard motor(s). Fuel
filtration systems of this type will help prevent
water that may be present in your boat’s fuel
tank(s) from contaminating your motor’s electronic fuel injection system. Water contamination can cause poor engine performance and
can also cause damage to the electronic fuel
injection system components.
Your Authorized Suzuki Marine Dealer can provide you advice about water-separating fuel filter systems and installation.
Gasoline Containing MTBE
Unleaded gasoline containing MTBE (Methyl
Tertiary Butyl Ether) may be used in your outboard motor if the MTBE content is not greater
than 15%. This oxygenated fuel does not contain alcohol.
Gasoline/Ethanol Blends
Blends of unleaded gasoline and ethanol (grain
alcohol), also known as gasohol, may be used
in your outboard motor if the ethanol content is
not greater than 10%.
Gasoline/Methanol Blends
Avoid using blends of unleaded gasoline and
methanol (wood alcohol) whenever possible.
DO NOT USE fuels containing more than 5%
methanol under any circumstances. Fuel system damage or outboard motor performance
problems resulting from the use of such fuels
are not the responsibility of Suzuki and may not
be covered under the New Outboard Motor Limited Warranty.
Fuel containing 5% or less methanol may be
suitable for use in your outboard motor if they
contain cosolvents and corrosion inhibitors.
Fuel Pump Labeling
In some states, pumps that dispense oxygenated fuels are required to be labeled for the type
and percentage of oxygenate, and whether
important additives are present. Such labels
may provide enough information for you to
determine if a particular blend of fuel meets the
requirements listed above. In other states,
pumps may not be clearly labeled as to the content or type of oxygenate and additives. If you
are not sure that the fuel you intend to use
meets these requirements, check with the service station operator or the fuel suppliers.
NOTE:
• Be sure that any oxygenated fuel blend you
use has octane ratings of at least 87 pump
octane ((R+M)/2 method).
• If you are not satisfied with the driveability or
fuel economy of your outboard motor when
you are using a gasoline/alcohol blend, you
should switch back to unleaded gasoline containing no alcohol.
• If engine pinging is experienced, substitute
another brand, as there are differences
between brands.
• Unleaded gasoline will extend spark plug life.
6
NOTICE
Gasoline kept in the fuel tank for long
periods of time will produce varnish and
gum, which can damage the engine.
Always use fresh gasoline.
FILLING THE FUEL TANK
To fill the fuel tank:
1. Always stop the engine before refilling the
tank.
2. Remove the portable fuel tank from the boat
to refill it.
WARNING
Gasoline is extremely flammable and
toxic. It can cause a fire and can be hazardous to people and pets.
Always take the following precautions
when refueling:
• Never permit anyone other than an
adult to refill the fuel tank.
• If you use a portable fuel tank, always
stop the motor and remove the fuel
tank from the boat to refill it.
• Do not fill the fuel tank all the way to
the top or fuel may overflow when it
expands due to heating by the sun.
• Be careful not to spill fuel. If you do,
wipe it up immediately.
• Do not smoke, and keep away from
open flames and sparks.
3. Turn the air-vent screw 1 on top of the fuel
tank cap 2 fully counterclockwise to open
the vent.
NOTE:
VENT SCREW should be CLOSED for transportation and OPEN for OPERATlON and CAP
REMOVAL.
4. Locate the pressure relief tab 3 under the
fuel tank cap and turn the cap counterclockwise until the tab engages the first lock.
NOTICE
Fuels containing alcohol can cause paint
damage, which is not covered under the
New Outboard Motor Limited Warranty.
Be careful not to spill fuel containing
alcohol while refueling. If fuel is spilled,
wipe it up immediately.
7
5. Press down on the tab, and release the lock,
–20 –10 0 10 20 30
–4 14 32 50 68 8640104
TEMP.
API Classification
SAE Viscosity Grade
10W–40
10W–30
˚F
˚C
SG
SH
SJ
SL
SM
then rotate the fuel tank cap 1/4 turn. The
tab will engage the second lock.
6. Press the tab down again and turn to
remove the fuel tank cap.
7. Carefully refill the fuel tank with gasoline.
Do not over fill.
8. Tighten the fuel tank cap until an audible
“click” is heard.
9. Tighten the air-vent screw on top of the fuel
tank cap.
ENGINE OIL
NOTICE
Use of poor quality engine oil can
adversely affect engine performance and
life.
Suzuki recommends that you use Suzuki
Marine 4-Cycle Engine Oil or its equivalent.
Oil quality is a major contributor to your
engine’s performance and life. Always select
good quality engine oil.
Suzuki recommends the use of SAE 10W-40 or
10W-30 SUZUKI MARINE 4-CYCLE ENGINE
OIL. If SUZUKI MARINE 4-CYCLE ENGINE
OIL is not available, select a NMMA certified
FC-W oil or good quality 4-cycle motor oil from
the following chart according to the average
temperatures in your area.
8
NOTE:
In very cold weather (below 5°C (41°F)), use
SAE (or NMMA FC-W) 5W-30 for easier starting and smooth operation.
GEAR OIL
Suzuki recommends the use of SUZUKI
HYPOID GEAR OIL. If it is not available, use
SAE 90 hypoid gear oil which is rated GL-5
under the API classification system.
LOCATION OF SAFETY LABELS
WARNING
AVERTISSEMENT
8
• Fuel can leak creating a fire hazard if
you lay motor on its side. Drain fuel
completely from vapor separator or
carburetor before laying motor on its side.
• See owner’s manual for details.
• Le carburent risque de fuir et de
présenter un danger d’incendie si le
moteur est placé sur le côté.
Vidanger entièrement le carburant du
séparateur de vapeurs ou du
carburateur avant de procéder.
• Pour plus de détail, voir le manuel
du propriétaire.
WARNING
AVERTISSEMENT
8
•
To avoid injury, when engine is running,
keep your hands, hair, clothing, etc., away
from engine.
•
See owner’s manual for details.
•
Pour éviter toute blessure, quand le moteur
est en marche, éloigner les mains, les
cheveux, les vêtements, etc. du moteur.
•
Pour plus de détail, voir le manuel
du propriétaire.
Label symbol meanings
These symbols mean as follows;
: General warning symbol
(Caution or Warning)
: Read owner’s manual carefully
: Remote control lever/gear shift
lever operation-two direction;
Forward/Neutral/Reverse
: Engine start
: Hazard caused by fire
: Hazard caused by laying the
motor on its side
: Hazard caused by rotating parts
Read and follow all of the labels on your outboard motor or fuel tank. Make sure you understand all of the labels.
Keep the labels on your outboard motor or fuel
tank. Do not remove them for any reason.
9
LOCATION OF PARTS
MONITOR-TACHOMETER
Priming bulb
FUEL HOSE
Power trim and
tilt (P.T.T.) switch
Remote control handle
Warm-up lever
Lock-out
lever
Ignition key
Emergency
stop switch
Throttle tension adjuster
SIDE MOUNT TYPE
TOP MOUNT TYPE
Power trim and tilt
(P.T.T.) switch
Remote control
handle
Free accelerator button
REMOTE CONTROL BOX (Option)
Motor cover
Power trim and tilt
(P.T.T.) switch
(Reverse side)
Engine oil drain plug
Clamp bracket
Anode
Gear oil level plug
Water intake hole
Gear oil drain plug
Pilot water hole
Flush plug
Anti-cavitation plate
Trim tab
(Anode)
Flush plug
DF40A/50A/60A
Ignition key
Emergency
stop switch
10
Motor cover
Power trim and tilt
(P.T.T.) switch
(Reverse side)
Engine oil drain plug
Clamp bracket
Anode
Pilot water hole
Flush plug
Anode
Gear oil level plug
Water intake hole
Gear oil drain plug
Anti-cavitation plate
Trim tab
DF50AV/60AV
Anode
(Reverse side)
11
MOTOR INSTALLATION
BATTERY INSTALLATION
WARNING
Overpowering your boat can be hazardous. Excessive horsepower will have an
adverse effect on hull safety and may
cause operating/handling difficulties. The
boat may also sustain stress and hull
damage.
Never install an outboard motor with
horsepower exceeding the manufacturer’s recommended maximum horsepower listed on the boat’s “Certification
Plate”. Contact your authorized Suzuki
marine dealer if you are unable to locate
the hull “Certificate Plate”.
NOTE:
It is against federal regulations for any marine
dealer to service a motor that exceeds the recommended maximum horsepower for your
boat.
Suzuki strongly recommends that you have
your outboard motor, controls and gauges
installed by your authorized Suzuki Marine
Dealer. He has the tools, the facilities and the
know-how.
WARNING
BATTERY REQUIREMENT
Choose a 12 Volt cranking-type lead acid battery that meets the specifications shown below.
650 Marine Cranking Amps (MCA)/ABYC,
or 512 Cold Cranking Amps (CCA)/SAE
or 160 Reserve Capacity (RC) Minutes/SAE
NOTE:
• The specifications listed above are the minimum battery rating requirements for starting
the engine.
• Additional electrical loads from the boat will
require larger capacity batteries. Consult
your Suzuki dealer to determine the proper
battery sizing for your boat and engine combination.
• Dual-purpose (Cranking/Deep-cycle) batteries can be used if they meet the minimum
specifications listed above (MCA, CCA, or
RC).
• Do not use a Deep Cycle battery for the main
cranking battery.
• The use of Maintenance-Free, sealed, or GelCell batteries is not recommended because
they may not be compatible with Suzuki’s
charging system.
• When connecting batteries in parallel, they
must be of the same type, capacity, manufacturer, and of similar age. When replacement
is necessary, they should be replaced as a
set. Consult your Suzuki dealer for proper
battery installation information.
Failure to have your outboard motor and
associated controls and gauges properly
installed can result in personal injury or
damage.
Suzuki strongly recommends that you
have your outboard motor, controls and
gauges installed by your authorized
Suzuki marine dealer. He has the tools,
the facilities, and the know-how to do the
job correctly.
12
BATTERY INSTALLATION
Red lead
Hexagonnut
Black
lead
Hexagonnut
Hexagon-nut
Secure the battery in a dry area of the boat,
away from vibration.
To remove the battery, first disconnect the black
lead from the negative terminal, then disconnect the red lead from the positive terminal.
NOTE:
• It is recommended that the battery be
installed in an enclosed battery case.
• When connecting batteries, hexagon-nuts
must be used to secure battery leads to battery posts.
To hook up the battery, first connect the red
lead from the motor to the positive battery terminal, then connect the black lead to the negative battery terminal.
Connecting and disconnecting the battery as
described above will help minimize the chance
of creating an accidental short circuit and
sparks.
Suzuki recommends that you install the terminal cap on the positive battery terminal to prevent an accidental short circuit of battery
terminals.
If a terminal cap is required, contact your authorized Suzuki marine dealer.
WARNING
Batteries produce flammable hydrogen
gas and may explode if they are near
flames or sparks.
Never smoke or cause sparks when working near the battery. Keep the battery
away from open flames. To avoid creating
a spark when charging the battery, connect the battery charger cables to the
proper terminals before turning the
charger on.
WARNING
If you place the battery near the fuel tank,
a spark from the battery may ignite the
gasoline, causing a fire and/or an explosion.
Do not place the fuel tank in the same
compartment/area as the battery.
WARNING
Battery acid is poisonous and corrosive.
It can cause severe injury and can damage painted surfaces.
Avoid contact with eyes, skin, clothing,
and painted surfaces. If battery acid
comes in contact with any of these, flush
immediately with large amounts of water.
If acid contacts the eyes or skin, get
immediate medical attention.
13
NOTICE
PROPELLER SELECTION
AND INSTALLATION
The electrical system or its components
may be damaged if proper battery precautions are not followed.
• Be sure to attach battery leads correctly.
• Do not disconnect battery leads from
the battery while the engine is running.
USE OF ELECTRICAL ACCESSORIES
The amount of power (12V DC) available for
accessories depends on the operating condition of the motor. For getting a detailed information, please inquire of your authorized Suzuki
Marine Dealer.
NOTE:
Use of too much power for electrical accessories under certain operating conditions can
cause the battery to discharge.
PROPELLER SELECTION
It is essential to use a propeller on your outboard motor that is properly matched to your
boat’s operating characteristics. The speed of
the engine when you operate your boat at full
throttle depends on the propeller you use.
Excessive engine speed can seriously damage
the motor, while low engine speed at full throttle
will adversely affect the performance. Your
operating load will also affect propeller selection. Smaller loads generally require largerpitch propellers; larger loads generally require
smaller-pitch propellers. Your authorized Suzuki
Marine Dealer will assist you in selecting a suitable propeller for your boat.
NOTICE
Installing a propeller with either too much
or too little pitch will cause incorrect
maximum engine speed, which may
result in severe damage to the motor.
Ask your authorized Suzuki marine
dealer to assist you in selecting a suitable propeller for your boat.
14
You can determine if your propeller is appropriate for use with your boat by using a tachometer to measure engine speed when operating
your boat at full throttle, under minimum load
conditions. If you are using an appropriate propeller, the engine speed will be within the following range:
DF40A
DF50A/50AV
DF60A/60AV
If the engine speed is not within this range, consult your authorized Suzuki Marine Dealer to
determine which propeller size is best for you.
If you change propellers, be sure to perform the
above check again, to confirm that the engine
speed under full throttle is within the specified
range.
5000 – 6000
r/min. (min
5300 – 6300
r/min. (min
–1
)
–1
)
PROPELLER INSTALLATION
• Trim angle too small (Boat tends to “plow”)
•
Trim angle too large (Boat tends to “porpoise”)
• Proper trim angle
ADJUSTMENTS
WARNING
Failure to take proper precautions when
installing or removing the propeller can
result in severe personal injury.
When installing or removing the propeller:
• Always shift into “Neutral” and remove
the emergency stop switch lock plate
so that the motor cannot be started
accidentally.
• Wear gloves to protect hands, and
“lock” the propeller by placing a block
of wood between the blades and the
anti-cavitation plate.
To install a propeller on your outboard motor,
use the following procedure:
TRIM ANGLE ADJUSTMENT
To help maintain steering stability and good
performance, always maintain the proper trim
angle as shown in the illustration. The appropriate trim angle varies depending on the combination of the boat, engine, and propeller, as well
as operating conditions.
Make a test run in the boat to determine if the
trim angle needs to be adjusted. Adjust the trim
angle using the Power Trim and Tilt system.
Refer to the POWER TRIM AND TILT section.
If you still cannot achieve good performance,
there may be a problem with engine mounting
height. Consult your dealer for assistance.
1. Coat the propeller shaft splines 1 liberally
with Suzuki water resistant grease to help
prevent corrosion.
2. Place the stopper 2 on the shaft.
3. Align the propeller 3 with the propeller shaft
splines and slide the propeller onto the shaft.
4. Place the spacer 4 and washer 5 on the
shaft.
5. Install the propeller nut 6 and tighten it with
a torque wrench to 50 – 60 N·m (5.0 – 6.0
kg-m/36.0 – 43.5 lb-ft).
6. Align the grooves in the propeller nut with
the hole in the shaft, then insert the cotter
pin 7 and bend the pin ends over to lock it in
place.
To remove the propeller, reverse the above procedure.
15
WARNING
Tilt range
Trim range
Trim angle greatly affects steering stability. If the trim angle is too small, the boat
may “plow” or “bow steer”. If the trim
angle is too large, the boat may “chine
walk” from side to side or “porpoise” up
and down. These conditions, which result
in loss of steering control, can cause
occupants to be thrown overboard.
Always maintain proper trim angle based
on the combination of your boat, engine,
and propeller, as well as operating conditions.
NOTICE
If you operate the boat with the motor
trimmed beyond the maximum trim position, the water intake holes may be above
the water line, causing severe engine
damage due to overheating.
Never operate the boat with the motor
trimmed beyond the maximum trim position.
16
WARNING
When the motor is tilted beyond the maximum trim position, the swivel bracket will
not have side support from the clamp
bracket and the tilt system will be unable
to cushion the engine if the lower unit
strikes an obstruction. This could lead to
occupant injury.
Do not operate the engine above 1500
r/min or operate the boat in a planing attitude with the motor tilted beyond the
maximum trim position.
TRIM TAB ADJUSTMENT
Side mount
type
This adjustment is used to compensate for the
possible tendency of your boat to veer slightly
to port or starboard. This tendency could be
due to such things as propeller torque, motor
mounting position, etc.
To adjust the trim tab:
1. Loosen the bolt A that holds the trim tab in
place.
2. If the boat tends to veer to port, move the
rear end of the trim tab toward the port side.
If the boat tends to veer to starboard, move
the rear end of the trim tab toward the starboard side.
THROTTLE TENSION ADJUSTMENT
The tension of the remote control handle can be
adjusted according to your preference. To
increase the tension, turn the adjuster A clockwise. To decrease the tension, turn the adjuster
counterclockwise.
NOTE:
Top mount type
When adjusting the tension of the remote control handle, consult your authorized Suzuki
Marine Dealer.
IDLE SPEED ADJUSTMENT
The idle speed has been factory adjusted
between 750 – 850 r/min. in neutral.
3. Tighten the bolt that holds the trim tab in
place.
After adjusting the trim tab, check to see if the
boat still tends to veer to one side. If necessary,
readjust the trim tab.
NOTE:
If idle speed cannot be set within the specified
range, contact your authorized Suzuki Marine
Dealer.
17
SETTING OF TILT UPPER LIMIT POSITION
“NEUTRAL”
UP
PTT switch
5. Press the “UP” side of the PTT switch for
<DF50AV/60A/60AV>
If the outboard motor contacts the motor well of
the boat during full tilt up operation, the upper
limit setting should be reset.
Perform this set-up after the current position
setting has been canceled, as explained in the
following procedure.
CANCELING THE TILT UPPER POSITION
LIMIT SETTING
1. Turn the ignition key to the “ON” position.
2. Pull out the emergency stop switch lock
plate.
6. Return the throttle to the fully closed posi-
SETTING THE TILT UPPER POSITION
LIMIT
7. Press the “UP” side of the PTT switch so
8. Using the throttle only function of the
3. Make sure that remote control handle is in
“NEUTRAL”.
4. Using the throttle only function of the remote
control box, move the warm-up lever upward
until the caution buzzer sounds one time.
9. Press the “UP” side of PTT switch three
10. Return the throttle to the fully closed posi-
three seconds and the buzzer will sound
twice briefly indicating the setting has been
canceled.
tion.
that the optimum full tilt up position for the
boat can be obtained.
remote control box, move the warm-up lever
upward until the caution buzzer sounds one
time.
times within three seconds. The buzzer will
sound one time briefly indicating the setting
has been accepted.
tion and install the lock plate on the emergency switch. Operate the full tilt up and full
down operations several times by pressing
the PTT switch and check that the setting of
both the trim lower limit and tilt upper limit
are properly set.
18
WARNING
Setting of the tilt upper limit position will
not prevent the outboard motor from tilt-
CAUTION SYSTEM
The caution systems are designed to alert you
to certain situations which may cause damage
to your outboard motor.
ing fully up and contacting the motor well
if the motor’s lower unit hits an object at
high speed. Such tilting could damage
your motor and boat and injure boat
occupants.
Keep all occupants away from the motor
when operating at high speed.
NOTICE
Your outboard motor may become damaged if you rely on the Caution System to
alert you to any malfunction that may
occur or to give you an indication of the
need for maintenance.
MOTOR COVER FASTENING ADJUSTMENT
If you feel the motor cover fastening is loose or
too tight when locking the levers, adjust as follows:
1. Loosen the bolt 1.
2. Adjust the position of bracket 2. To increase
the fastening, move the bracket to the direction A. To decrease the fastening, move the
bracket to the direction B.
3. Tighten the bolt 1.
To avoid damage to your outboard motor,
regularly inspect and maintain it.
NOTICE
Continuing to operate your outboard
motor with the Caution System activated
can result in severe damage to your outboard motor.
If the Caution System activates while you
are operating your outboard motor, stop
the motor as soon as possible and correct the problem or consult your authorized Suzuki marine dealer for
assistance.
19
Loading...