Page 1
SAM-VTC Voice-Test Module
User Guide
1001 East Hwy 212
Hector, MN 55342
www.suttleonline.com
Toll Free: 1-800-852-8662
Local: 1-320-848-6711
Fax: 320-848-2361
Page 2
Module Installation
p)
g)
Mounting:
Align the mounting pins with the grid holes on the back of the enclosure.
With the mounting pin plungers in the “out” position, press the unit into
With the mounting pin plungers in the “out” position, press the unit into
the grid in the desired location, secure by pushing the plungers in.
the grid in the desired location, secure by pushing the plungers in.
Terminate incoming service line: Terminate incoming service line:
Run jumper cords to the Module to connect to jacks marked “LINE IN”.
Run jumper cords to the Module to connect to jacks marked “LINE IN”.
These are RJ-14, 6-position/4-conductor jacks, the inner conductor pair
These are RJ-14, 6-position/4-conductor jacks, the inner conductor pair
is Line 1 (3, 5 or 7) and the outer conductor pair is Line 2 (4, 6 or 8).
is Line 1 (3, 5 or 7) and the outer conductor pair is Line 2 (4, 6 or 8).
In Line 1&2
Test Line 1&2
Terminate outgoing lines: Terminate outgoing lines:
Run jumper cords from the jacks marked “LINE OUT” to the desired
Run jumper cords from the jacks marked “LINE OUT” to the desired
location, or use the 110 IDC terminals to terminate the outgoing lines.
location, or use the 110 IDC terminals to terminate the outgoing lines.
110 IDC Termination Procedure 110 IDC Termination Procedure
Run twisted pair cable from the terminals to the desired location.
Run twisted pair cable from the terminals to the desired location.
Strip 3 in. of outer jacket from the cable. Punch individual cable pairs
Strip 3 in. of outer jacket from the cable. Punch individual cable pairs
down on the 110 IDC. Starting at the blue position on the IDC, begin
down on the 110 IDC. Starting at the blue position on the IDC, begin
with the white wire of each pair as you progress to the orange position
with the white wire of each pair as you progress to the orange position
on the IDC as shown below. Press wires into slots with a 110-punch
on the IDC as shown below. Press wires into slots with a 110-punch
tool. Trim and discard excess wires.
tool. Trim and discard excess wires.
s on the back of the enclosure.
Out Line 1(rin
Out Line 1&2
Out Line 1(ti
Page 3
Brown
NOTE: one pair of wires corresponds
to each line from the phone company.
(Line 1 = blue, Line 2 = orange,
Line 3=green, Line 4=brown).
White/Brown
Green
White/Green
Orange
White/Orange
Blue
White/Blue
The wire pair locations can be recorded on the wiring label supplied with
this module. Attach the wiring label to the inside of the enclosure cover.
Testing incoming service line:
To test the incoming service lines, plug the tester into the jack marked
“TEST” for the appropriate line. The test port will not disconnect service
between the “LINE IN” and the “LINE OUT” jacks. As indicated above,
these are RJ14, 6-position/4-conductor jacks, the inner conductor pair is
Line 1 (3, 5 or 7) and the outer conductor pair is Line 2 (4, 6 or 8).
Important Information:
• Read and understand all instructions. Follow all warnings and
instructions marked on the product.
• Do not use this product near water, --e.g., near a bath tub, wash basin,
kitchen sink, wet basement, or near a swimming pool.
• Never push objects of any kind into this product through openings, as
they may contact dangerous voltages.
• SAVE THESE INSTRUCTIONS.
Safety Information:
• Never install communications wiring during a lightning storm.
• Never touch uninsulated wires or terminals unless the wiring has been
disconnected at the network interface.
• Never install communications components in wet locations unless the
components are designed specifically for use in wet locations.
Page 4
1001 East Hwy 212
Hector, MN 55342
www.suttleonline.com
p/n 100963-00 Rev. B
Toll Free: 1-800-852-8662
Local: 1-320-848-6711
Fax: 320-848-2361
Loading...