Page 1
Fergus 4x4
SSB070ST
Installation Instructions
Rev 01 Page 1
Page 2
SSB070ST
Fergus the 4x4 Instructions
Installation Instructions
1. Check using the parts list that all components have been delivered.
2. Plan the final position of the play equipment, ensuring there is sufficient space
NB: Please consider the extent and HIC of surfacing (see surfacing plan).
Ensure that bow and stern are faced away from thoroughfares and desire lines
(in the direction of movement).
3. Sort and identify parts before assembly, only ground fixing (THF045) is
required at this stage
4. Excavate the foundation holes in accordance with the plan and play level,
ensuring the hole is dug to achieve a horizontal finish to the bottom of the
hole.
5. Place 4x4 ground fixing in to the foundation hole and level top plate.
6. Check the unit will sit at the correct level and position as per the elevations
and plans provided before tightening bolts now fill the foundation holes to the
required depth with concrete. Float off upper surface to enable run-off away
from ground fixing uprights.
7. Leave foundation to fully set before continuing to install the 4x4 body (at least
2-3 days, setting times may vary)
8. Fix 4x4 deck panel (SSB086) to top frame of mechanism, DO NOT tighten
bolts or attach covers until assembly is complete.
NB: Use the panel fixing general sheet supplied to select the correct bolts from
the fixing kit (be advised that a few surplus fixings are generally included).
We suggest fixing countersunk bolts first as on occasion another panel may
be layered on top of them. It is important not to fully tighten the fixings until all
panels have been assembled and the unit is stood within the foundation holes.
Rev 01 Page 2
Page 3
SSB070ST
Fergus the 4x4
Installation Instructions
9. Secure first 4x4 left and right side panels (SSB071 & SSB072) to deck panel
using 3mm L brackets, DO NOT tighten bolts or attach covers until assembly
is complete.
10. Offer up the vertical footwell panels (SSB076) to the front and rear, inside the
body of the 4x4 and secure using Fixing & Assembly Instructions (Figs 2,4 &
5).
11. Offer up seat, dashboard and boot support rails and attach between the side
panels, taking care to attach the wheels and wheel arches at the same time
(See Panel Layering : Fixing & Assembly instructions - Fig 6). DO NOT tighten
bolts or attach covers until assembly is complete.
12. Secure seat, dashboard and boot panels to the support frames
13. Offer up the 4x4 front panel (together with bumper and headlights and secure
using Fixing & Assembly Instructions (Figs 2, 4 & 5).
14. When all fixings are in place, then proceed to tighten bolts, ensuring adjacent
panels are butted up to prevent finger traps.
15. Ensure all exposed hex-head bolts are capped off using the step washers
and nylon caps provided (refer to panel fixing general sheet supplied) The unit
should be secured against use by any member of the public until the concrete
is set and the appropriate depth and extent of surfacing have been installed
(please refer to surfacing plan).
16. Follow the maintenance instructions supplied at the end of this document
NB: During installation, care must be taken to prevent hazards to children. If
you are at all unsure or have any questions, please contact the contracts
department immediately for their assistance and advice.
Rev 01 Page 3
Page 4
SSB070ST
Fergus 4x4
Parts List
Ground fixing (THF045)
Deck Panel
(SSB086)
Left Wheels x2
(THP082)
Right Wheels x2
(THP083)
Left side panel
(SSB071)
Right side panel
(SSB072)
Rev 01 Page 4
CZD100
Page 5
SSB070
Fergus the 4x4
Parts List List
Front seat side
panel (SSB065)
Front seat support
(SSB051)
Front seat panel
(SSB063)
Front seat
backrest panel
(SSB064)
Footwell panel
x2 (SSB076)
Front grill
(SSB082)
Boot panel assembly (SSB087)
(add Number plate SSB069)
Rev 01 Page 5
HPL headlights
x2 (SSB048)
Front bumper
(SSB074)
Page 6
SSB070
Fergus the 4x4
Parts List List
Front wheel arch
panel (SSB077)
x2
View Here
Dashboard panel
(SSB075)
Rear wheel arch
panel (SSB078)
x2
Steering wheel
(MZA304Y)
Support rails x2
(SSB080YEL)
Rear Seat panel
(SSB066)
Rev 01 Page 6
CZD100
Rear seat
backrest panel
(SSB067)
Page 7
SSB070ST
Fergus the 4x4
Parts List
SSB064
SSB051
SSB063
Front seat
(not seen)
SSB065
SSB075
MZA304Y
SSB072
SSB077
THP083
SSB076
SSB080
SSB082
SSB087
SSB078
THP083
SSB067
SSB066
SSB080
THF045
SSB078
SSB071
THP082
SSB048
SSB074
THP082
SSB077
Rev 01 Page 7
CZD100
SSB086
Page 8
SSB050ST
Fergus the 4x4
Maintenance Instructions
NB: The warranty is invalidated if these instructions are not followed.
All wood needs annual inspection and retreatment where required.
Recommended Regular Inspection and Maintenance Interval Days
7 14 28 56 365
Check stability of structure, tighten connections if required.
Check all uprights at ground level for corrosion and/or rot.
Replace any defective parts.
Check all painted elements for damage, rub down and repaint or
replace as required.
Check chain/ropework assemblies for wear and damage, replace if
required.
Check ground fixing for integrity.
Check slide chutes for smoothness and any foreign elements,
remove any found.
Check rubber safety surfaces for damage and poor performance,
repair or replace if required.
Check loose fill safety surfaces, remove any foreign elements, rake
level and top up if required.
Disposal Instructions
All components should be broken down into categories of:1 Mild Steel - all 38mm Ø tube, step/ring climbers, welded bar, swing frames, deck frames, springie frames.
2 Stainless Steel - all slides, mirror panels.
3 Aluminium - all Playzone, Mission and Toddlerzone posts.
4 Galvanised Steel - all chains and Teenzone posts.
5 Moulded Rubber Products without steel inserts - all Mission and Toddlerzone Caps and edge details.
6 Timber - all natural timber, plywood, and MDF panels.
Wherever possible these materials should be taken to specialist recycling organisations and recycled.
In some cases where composite materials are used, then disposal at land fill sites is the only alternative such
as:
7 Moulded Rubber Products encasing steel inserts - all Swing Seats, Deck Tops, Duo/Dizzy Disc Tops.
8 High Pressure Laminate - all Toddlerzone, Playzone, Minizone, Teenzone and Themed panels.
9 Steel Core Polypropylene Rope - all Scramble Nets, Space Nets, Playzone/Toddlerzone/Mission Ropes.
Rev 01 Page 8
Loading...