Sussman ES series, HU series, ES 12, ES 18, ES 24 Installation, Operation And Maintenance Manual

...

Download

Page 1

ES & HU Installation, Operation and Maintenance Manual

Model No. _____________________________________

Boiler Serial No. _______________________________

National Board No. ___________________________

Safety Valve Set Pressure _______________ PSIG

Power Circuit Voltage _______________________

Control Circuit Voltage ______________________

Amps __________ Phase _________ HZ __________

Steam Outlet Valve Size _____________ NPT

IMPORTANT:

This data file contains the National Board Registration Certificate approving your boiler. It must be kept near the boiler at all times.

Products covered by this manual:

_________________________________________________________________________________

KW Max Design Work

Series Range Steam Rate* BHP Pressure Pressure

_________________________________________________________________________________

ES, HU 12-180 36-542 lbs/hr 1.2-18.4 0-100 psig 85 psig

_________________________________________________________________________________

*Steam Rate: Steam at 212˚ F with 50˚ F feed water

ES and HU boilers are of Carbon Steel construction. See page 23 for Water Quality Information.

TABLE OF CONTENTS

Dimensional Information and

Component Identification . . . . . . . . . . . . . . . . . 2

Dimensional & Clearing Specifications. . . . . . . . . 3

Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . 4-7

Installation

Piping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Pre-Operation Check . . . . . . . . . . . . . . . . . . . . . . . 10

Pressure Controls, Operation & Testing . . . . . . . 10

Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Blowdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Digital Timer Operation Instructions. . . . . . . . . . 12

Timing Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Standard Equipment

Auxiliary Low Water Cut Off . . . . . . . . . . . . . . . . 14

Line Pressure Water Feed System . . . . . . . . . . . . . 14

Optional Equipment

High Pressure Water Feed System. . . . . . . . . . . . . 14

Condensate Return System. . . . . . . . . . . . . . . . . . 14

Vacuum Breaker Systems . . . . . . . . . . . . . . . . . . . 15

Automatic Blowdown System. . . . . . . . . . . . . . . . 15

Control Voltage Stepdown Transformer . . . . . . . . 15

Blowdown Separators . . . . . . . . . . . . . . . . . . . . . 15

Multistage Load Progressive Sequencers . . . . . . . . 15

Condensate Return Systems . . . . . . . . . . . . . . . . 16

Blowdown Separator Tanks . . . . . . . . . . . . . . . . . 17

Specification Charts . . . . . . . . . . . . . . . . . . . . . . . 18

Sizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Gauge Glass Installation . . . . . . . . . . . . . . . . . 20-21

Element Replacement . . . . . . . . . . . . . . . . . . . . . . 22

Water Quality Information

for Carbon Steel Boilers . . . . . . . . . . . . . . . . . . 23

IMPORTANT NOTE:

As you follow these instructions, you will notice warning and caution symbols. This blocked information is important for the safe and efficient installation and operation of electric boilers. These are two types of potential hazards that may occur during this installation and operation:

WARN I N G

may cause serious injury or death if precautions are not followed.

states a hazard which

CAUTIO N

minor injury or product damage may occur if you do not follow instructions.

A Division of Sussman-Automatic Corporation

43-20 34th Street, Long Island City, NY 11101 • (718) 937-4500 1-800-238-3535 • Fax: (718) 937-4676 • email: [email protected]

www.sussmanboilers.com

signals a situation where

IMPORTANT NOTE:

This highlights information that is especially relevant to a problem-free installation.

M A D E I N U S A

PUR 101137 4.13

Page 2

Installation, Operation & Maintenance Manual

Dimensional Information & Component Identification

Models: ES, HU

Height

Width

_________________________________

SYMBOL ITEM ES12-18 ES24-72 ES100 ES135-180

___________________________________

Height Overall Height 36" 44" 59" 61"

__________________________________________________________________

Length Overall Length 28" 33" 34" 38"

__________________________________________________________________

Width Overall Width 20" 22" 26" 30"

__________________________________________________________________

A Steam Outlet 6-1/4" 10" 8-1/4" 9"

__________________________________________________________________

B Steam Outlet 10-1/4" 17" 17-1/4" 18-1/4"

__________________________________________________________________

C M/M Drain Valve 5" 12" 17" 16-3/4"

__________________________________________________________________

D M/M Drain Valve 6-1/2" 6" 6-1/4" 6-1/4"

__________________________________________________________________

E Check Valve 14" 9" 17" 16-3/4"

__________________________________________________________________

F PV Drain Valve 2-3/4" 2-1/4" 2-3/4" 2-3/4"

__________________________________________________________________

G PV Drain Valve 6-1/4" 9-1/2" 7-3/4" 9-1/4"

__________________________________________________________________

J Clearance 3-3/4" 3-1/2" 4" 4"

__________________________________________________________________

K Check Valve 2-1/2" 2-3/4" 3" 3"

__________________________________________________________________

M Door Width 8-3/4" 14" 12-3/4" 14-3/4"

__________________________________________________________________

Allow 24 inches all around for servicing.

Length

_______________________________________

MODEL HW L INLET OUTLET

_______________________________________

ES 12, 18; HU 40–55 36" 20" 28" 1/2” NPT 1/2”NPT

_________________________________________________

ES 24–72; HU 75–205 44" 23" 33" 1/2”NPT 1” NPT

_________________________________________________

ES 100; HU 310 59" 28" 34" 1/2”NPT 1-1/2”NPT

_________________________________________________

ES 135–180; HU 410–550 61" 30" 36" 1/2”NPT 2” NPT

_______________________________________

Allow minimum 21 inches clearance in front of door for servicing of heating elements. Recommended clearance: 24 inches all around boiler for servicing.

WATER STEAM

Page 3

Installation, Operation & Maintenance Manual

Dimensional & Clearance Specifications

Height

SteamOutlet

Operating Pressure

Gauge Glass Assembly

Control

On/Off

Switch

High Limit Pressure Control

Pressure Gauge

SafetyValve

LiquidLevel Control

Water Feed Inlet

Drain Valve

FrontLeft

Width Length

Side Elevation Front Elevation

Allow 24" all around for servicing.

__________________________________________________

Clearance from combustible surfaces

__________________________________________________

_________________________________________________________________________

G-

_________________________________________________________________________

1" Clearance above top of boiler

A Clearance from Front of boiler. Prefix "C" to numeral indicates acceptability for

closet or alcove installations; prefix acceptability for alcove installations but not for closet installations.

1" Clearance from back of boiler.

1" Clearance from left side of boiler.

16" Clearance from right side of boiler.

C Indicates type of flooring: "NC" for non-combustible; "C" for combustible.

Total minimum free area in square inches of close ventilating openings.

Page 4

H1 H3 H5 H7

FB1 FB2 FB3 FB4

FIELD WIRING

FACTORY WIRING

PILOT LIGHT

480V

120V

H2 H4 H6 H8

TO CONTROL

CIRCUIT

HEATING

ELEMENTS

TRANSFORMER

(optional)

TB 1

POWER FUSES

(see Note 2)

CONTACTORS C1 C2 C3 C4

SINGLE PHASE

MAIN POWER SUPPLY

L1 L2 G

TERMINAL POWER BLOCK (see note 1)

THREE PHASE

MAIN POWER

SUPPLY

Installation, Operation & Maintenance Manual

Typical Wiring Diagrams:

Three phase power circuit with separate 120Volt control circuit. (With singe phase power circuit insert.)

Three phase power circuit with step down transformer.

Detailed ES81017MR auxiliary low water cut off wiring.

ES81600 Auto blowdown wiring diagram.

Detailed sequencer package wiring diagram.

Wiring Diagram Power Circuit

ES Electric Boilers (Power Circuit)

NOTES:

1. Power Terminal Block only on boilers with two or more contactors.

2. On boilers with only one power contactor, connect power voltage to line side of contactor.

3. Power Fuses only on boilers rated 120 amperes and larger.

4. See Parts List for contactor and heating element information.

Page 5

RELAY

FIELD WIRING

FACTORY WIRING

PILOT LIGHT

OPERATING

PRESSURE

CONTROL

AUX LWCO PC BOARD

MANUAL RESET

PILOT LIGHT

COM

HIGH LIMIT

PRESSURE

CONTROL

LIQUID

LEVEL

CONTROL

ON-OFF SWITCH

CONTROL TERMINAL BLOCK

120V 1PH

INPUT

PROBE

SOLENOID VALVE

CONTACTORS

PUMP MOTOR

GND

LOW

RESET

RELAY

FIELD WIRING

FACTORY WIRING

PILOT LIGHT

OPERATING

PRESSURE

CONTROL

HIGH LIMIT

PRESSURE

CONTROL

LIQUID

LEVEL

CONTROL

ON-OFF SWITCH

CONTROL TERMINAL BLOCK

120V 1PH

INPUT

L1 L2

SOLENOID VALVE

CONTACTORS

PUMP MOTOR

Installation, Operation & Maintenance Manual

Wiring Diagram Control Circuit

ES Electric Boilers (Basic Control Circuit)

ES Electric Boilers with Manual Reset Auxiliary Low Water Cutoff

Page 6

Wiring Diagram Control Circuit

RELAY

IELD WIRING

ACTORY WIRING

ILOT

IGHT

OPERATING

PRESSURE

CONTROL

PROPORTIONING PRESSURE CONTROL

135 OHM

COM

SEQUENCER

HIGH LIMIT

PRESSURE

CONTROL

LIQUID

LEVEL

CONTROL

ON-OFF

WITCH

CONTROL TERMINAL BLOCK

120V 1PH

NPUT

L1 L2

SOLENOID VALVE

CONTACTORS

UMP MOTOR

20V COM

Installation, Operation & Maintenance Manual

ES Electric Boilers with Sequencer

ES 100 and up with Element Cutoff Switches

Page 7

RELAY

IELD WIRING

ACTORY WIRING

PILOT LIGHT

OPERATING

PRESSURE

CONTROL

HIGH LIMIT

PRESSURE

CONTROL

LIQUID

LEVEL

CONTROL

N-OFF

SWITCH

CONTROL T

ERMINAL

BLOCK

120V 1PH

NPUT

7-DAY 24-HR

IMER

TIME DELAY RELAY

S81600 AUTOMATIC BLOWDOWN SYSTEM

CONTACTORS

SOLENOID VALVE

PUMP MOTOR

OPEN

OTORI ZED

LOWDO WN

VALVE

Installation, Operation & Maintenance Manual

Wiring Diagram Control Circuit

ES Electric Boilers with Automatic Blowdown System

Page 8

Installation, Operation & Maintenance Manual

Installation

REFER TO NATIONAL AND ALL APPLICABLE LOCAL CODES FOR SPECIFIC INSTALLATION REQUIREMENTS.

1. The boiler should be mounted on a solid, level foundation.

2. The boiler should be located with suitable clearances, refer to page 3 and Code requirements.

NOTE: Allow minimum of 21 inches clearance in front of door for servicing of heating elements.

3. Do not install boiler in any location where water could freeze.

4. Do not install boiler outdoors.

5. Do not install boiler near flammable or corrosive materials.

6. Do not install boiler in a location where leakage from the boiler tank or piping can damage to adjacent areas or to lower floors of the structure. Provide a floor drain and properly sloped floor from the boiler towards the drain or install a suitably plumbed drain pan under the boiler.

NOTE: Allow a minimum of 36 inches of clearance in front of door for servicing of heating elements.

Piping

ALL PIPING SHOULD BE INSTALLED BY A QUALIFIED LICENSED PLUMBER IN ACCORDANCE WITH NATIONAL AND LOCAL CODES.

1. When water feed is other than pump type the water supply pressure must be 10 psig greater than boil-

er operating pressure to assure water supply maintains proper water level in the boiler. Insufficient water levels can result in improper boiler operation. (Keep feed water valves open at all times during normal operation.)

2. If pump and boiler are plumbed within 30 feet (pipe length) a minimum of 2 check valves are required to avoid damage to pump.

3. Connect steam line with customer supplied outlet valve to boiler steam outlet.

NOTE: For best performance, a globe valve rated for steam service higher than the maximum boiler pres-

sure should be plumbed on the steam outlet line; failure to do so can cause heating element breakdown. See page 1 for steam outlet valve size.

4. Provide for boiler drain connection, a daily blowdown is required. A "Blowdown Separator Tank" may be necessary, check with local code.

5. Safety valve shall be plumbed according to local code.

NOTE: The safety valve shall not be plumbed with a line sized less than the outlet size of the safety valve.

Page 9

Installation, Operation & Maintenance Manual

Wiring

ALL ELECTRICAL WIRING MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRICAL CODES.

CAUTIO N

matches the power voltage and phase of the boiler. Connecting incorrect power supply can damage boiler components or cause improper boiler operation. If the boiler power requirements do not match the power to be supplied to the boiler the boiler must be returned to the factory for conversion. Boilers cannot be field converted.

ALL BOILERS ARE PRE-WIRED AND TESTED PRIOR TO SHIPMENT.

Ground boiler according to National Electric Code requirements to avoid shock.

Power wiring to boiler should be in accordance with National and Local Electrical Code requirements following wiring diagram supplied. Use proper size wire. Wire size is specified adjacent to field wiring terminals. This label states the wire size [AWG or MCM], minimum temperature rating (90 C) and conductor material (copper only). Deviation from these requirements may result in improper or unsafe boiler operation.

A disconnect switch employing circuit breakers or fuses should be installed between the main power source and the boiler. This disconnect switch should be located near the boiler and clearly marked for easy access and identification should the boiler need to be turned off due to an emergency.

Boiler control circuit is 120 Volt*. Unless boiler has an optional step down transformer, a separate 120 Volt power feed wiring is required to be connected to the control circuit terminal block. A 15 Amp circuit is required for all boilers. If a 3/4 HP feed water motor and pump assembly is connected to the boiler, then a 20 Amp circuit is required.

Assure that the power voltage and phase being supplied to the boiler

If a separate control circuit is used, it should be connected to the control circuit terminal block.

Remote mounted water feed systems (i.e. condensate return, motor and pump) should be connected to the junction box provided on the outside of the boiler jacket.

With main power off, make sure all wiring terminations are tight to avoid arcing, carbonizing or overheating of contacts.

CAUTIO N

damage due to water line connections. An industrial type lightning/surge protector should be installed according to the manufacturer's recommendation at the service entrance. Consult your contractor or electrical dealer.

WARN I N G

cation of wiring system voids the warranty and may lead to dangerous operating conditions.

Boilers are susceptible to lightning

Substitution of components or modifi-

Page 10

Installation, Operation & Maintenance Manual

Pre-Operation Check (All Boilers)

LWCO/PUMP CONTROL OPERATION AND TESTING

All valves for incoming water supply are to be fully opened. Main disconnect switch is to be in the "on" position. Boiler main switch is to be in the "on" position. Since boiler will be empty the pump or solenoid will be energized allowing the boiler to fill with water. Control will automatically fill boiler to proper operating water level and the pump/solenoid will be de-energized. Contactors will then energize, applying voltage to the heating elements.

Pump switch operation – at this point water should be visible approximately half way up the sight glass. Slowly open the drain valve located at the bottom of the boiler. Water level in the sight glass will begin to drop, allowing the low water cut off/pump control to energize the feed water system. Close valve for proper operation.

Low water cutout switch performance – open the drain valve completely. Maintain this condition until water level falls within the gauge glass enough to cause the low water cutout switch to de-energize the heating elements. All of the contactors will be in a de-energized or open state at this time. Close the drain valve, water feed system will automatically refill the boiler and the contactors will re-energize.

Pressure Controls, Operation and Testing

Boilers equipped with an auxiliary low water cut-off control with a manual re-set button (required as mandatory equipment is some states): once the correct operating water level has been reached, it will be necessary to depress the reset button in order for the contactors to re-energize.

NOTE:

down system:

• For test 1 - the blowdown time clock must be in the

• For test 2 and 3 - in order for the drain valve to open

For boilers equipped with an automatic blow-

“run” mode before the boiler will automatically fill.

the blowdown clock must be in the “off” mode. (See blowdown time clock insert) The automatic blowdown indicator light will be on when the valve is open. This light will remain on for the duration of the blowdown cycle (a few seconds). It may be necessary to cycle the time clock from the “run” to “off” mode several times.

NOTE:

All boilers are provided with one high limit pressure control and at least one operating pressure control.

The high limit pressure control is equipped with a manual reset feature. There is no subtractive differential scale with this type of control

All pressure controls are equipped with an adjusting

screw, allowing for setting of desired operational and high limit pressures. To reduce pressure setting, turn adjusting screw in direction that allows indicator to point to a lower pressure setting on the scale. To increase pressure setting turn adjusting screw in direction that allows indicator to point to a higher pressure on the scale

NOTE:

10 psig above the desired normal operating pressure.

It is recommended that the high limit control be set

Operating pressure controls, except low pressure (15psig)

types have a separate differential scale. Differential indicates pressure below the main operating maximum pressure, the pressure control will re-set. The differential set point is adjusted in the same manner by turning the adjusting screw in the desired direction to increase or decrease the differential pressure value.

Operating pressure control check: Close steam outlet

valve [supplied by customer] and adjust operating pressure control to 20psig and the differential to 10psig. Set the high limit pressure control to 30psig. Switch boiler on to allow steam pressure to build-up. Pressure gauge reading will increase and the operating pressure control will de-energize the contactor(s) when the pressure gauge indicates 20psig. Open steam outlet valve to bleed off pressure. When the pressure gauge reading decreases below 10psig (differential) the operating pressure control will re-energize the contactor(s).

High limit pressure control check: FOR TEST PURPOSES

ONLY! Set the high limit pressure control 10psig lower

than the operating pressure control. Close the steam outlet valve and switch the boiler on to allow boiler to build pressure. When the pressure gauge indicates the pressure at which the high limit pressure control is set, the high limit pressure control re-set button will popup and the control will de-energize the contactor(s). Open the steam outlet valve to bleed off pressure. The contactor(s) should not re-energize on pressure drop. The contactor(s) should only re-energize when the pressure has dropped and the high limit pressure control reset button is depressed.

Page 11

Installation, Operation & Maintenance Manual

Operation

CAUTIO N

lectrical connections before energizing boiler to prevent

e arcing, carbonizing of contact and/or overheating

1. Set the desired operating pressure and differential pressure

on the operating pressure control.

2. Set the high limit pressure control. (Recommended to be 10 psig above the operating pressure setting.)

3. Turn on water supply.

4. Turn main disconnect switch on.

5. Turn boiler control switch on. The water feed will begin

and continue until the water level reaches half way up the gauge glass. The water feed will automatically shut off and the contactor(s) will energize.

6. Boiler steam pressure will gradually increase to the operat-

With main disconnect “OFF” tighten all

ing pressure control set point, at which time the contactor(s) will de-energize.

7. With steam demand, the boiler steam pressure will decrease. When the boiler pressure has dropped below the operating pressure control differential set amount, the contactor(s) will re-energize.

Note: Adjust steam outlet valve such that the boiler pressure does not drop more than 20% below reset.

8. The boiler is equipped with float type liquid level controls employing micro switches. They are extremely sensitive and reliable and will maintain the proper water level within the boiler pressure vessel automatically during boiler operation.

9. The boiler should be blown down daily. (See blowdown instructions.)

Blowdown

A daily blowdown is an essential part of boiler operation. It is the best and most important part of preventative maintenance you can give your boiler and will add years of life to the unit. Make sure a blowdown schedule is established and followed regularly.

In extremely hard water areas, blowdown may be necessary more than once a day. If there is a particular problem that applies to your local water condition (i.e. high concentrations of minerals etc.) we recommend a consultation with a reputable local water treatment-engineering firm. Pre-treating the boiler feed water may reduce mineral accumulation enough to allow a daily blowdown to be sufficient.

MANUAL BLOWDOWN INSTRUCTIONS

1. At the end of the working day, while boiler is still operating,

turn boiler main switch to the “OFF” position, close water supply valve and open disconnect switch.

2. If blow down valve is plumbed into a blowdown tank, the boiler can be discharged at operating pressure.

3. If the blowdown valve is not plumbed into a blowdown tank, consult with local plumbing codes regarding boiler discharge.

4. When discharge is complete and boiler is drained, close the blowdown valve, open the water supply valve, turn boiler main switch to “ON” position and close disconnect switch.

5. When refilling is complete, turn off the boiler unless further operation is needed.

6. If boiler is equipped with a “Manual Re-set Auxiliary Low Water Cut-off” (as required in some states) the re-set button must be pushed before the boiler will begin developing steam. Do not push re-set button until the boiler has refilled with water.

AUTOMATIC BLOWDOWN INSTRUCTIONS

(PN ES81600) 1” NPT, Starts, stops and blows down the

boiler automatically, utilizing a programmable time clock a time-delay relay and motorized ball valve.

CAUTIO N

a blowdown tank, the boiler can be discharged at operating pressure. If the blowdown valve is not plumbed into a blowdown tank, consult with local plumbing codes regarding boiler discharge.

NOTE:

lower float control equalization tube must be fully open for the automatic blowdown to be effective.

1. Program time clock by setting the time boiler is to turn

2. When the time clock turns the boiler “off” the blow-

3. Boiler will automatically refill at next programmed on

Blowdown program can be overridden to allow for unscheduled blowdown or operational cycles. Refer to the time clock instruction insert.

The manual valves from the boiler drain and the

on and off daily. (Refer to instructions in time clock insert.)

down is activated. A red pilot light over the time clock will come on and remain on while the motorized ball valve is open. The time duration the valve is open is set by an adjustable potentiometer built into the time delay board. The water level in the boiler after blowdown is complete, will be approximately at the lower gauge glass valve. (Elements are not exposed to air between operations.)

cycle.

If the blowdown valve is plumbed into

Page 12

Installation, Operation & Maintenance Manual

Mo Tu We T

h Fr S

a Su

+- Menu OK

Res.

+1h

Digital Timer - Operation Instructions

TO SET TIME & DAY OF CLOCK

1. Press Menu

2. 24h AM or PM blinking, press + or – to select, press OK

3. Hour (12:00) blinking, press + or – to select, press OK

4. Minute (12:00) blinking, press + or – to select, press OK

5. Arrows for days

press + or – to select, press OK

6. Go to step 8 to continue with programming or press

Menu to end.

TO SET TIMER ON/OFF TIMES

7. Press Menu and press OK four times to go

current time/day setting above

8. prog 01 blinking and ON symbol or – to select, press OK

9. Hour (12:00) blinking, press + or – to select, press OK

10. Minute (12:00) blinking, press + or – to select, press

11. Arrows for days

blinking, press + or – to select,



press OK

12. prog 02 blinking and

OFF

symboldisplayed,

press + or – to select, press OK

13. Hour (12:00) blinking, press + or – to select, press OK

14. Minute (12:00) blinking, press + or – to select, press

15. Arrows for days

blinking, press + or – to select. See



possible combinations below.

16. Press Menu to end or press OK and repeat steps 8 to 15 to set more ON/OFF times.

displayed, press +



blinking,



ON/OFF STATUS

symboldisplayed when timer isonand

OFF

symboldisplayed when timer is off.

OVERRIDE/AUTOMATIC

When the timer is the timer

OVR

arrow

Offand display arrowwill point to

. Press + again to go back to

will point to



When the timer is the timer

OVR

Onand display arrowwill point to

Press + again to go back to

will point to



When the timer is in the override mode timer will stay in that position until the next programmed time, at which time the arrow_will point to

AUTO

and continue in the automatic mode.

On, press + to manually turn

Onand display

AUTO

Off, press + to manually turn

Offand display arrow

AUTO

(on

OVR

HOURLY ON/OFF SETTING FOR THE DAY

Hash marks on the upper and right edges of the display show the hourly On times for the day. Absence of hash mark on a specific hour indicates that the timer is Off on that hour.

DAYLIGHT SAVING TIME.

In the Run mode, use a pencil point and press+ for Daylight Saving Time and current time advances

one hour and + Standard Time, press + one hour and +

displayed. To revert back to

and current time falls back

display disappears.

PROGRAMMED DAY COMBINATIONS:

Every day (arrowson all days) Monday to Saturday Monday to Friday Saturday and Sunday Any individual day

RUN MODE

On Run mode, display will show current time/ date, on/off status, override/automatic status, hourly on/off setting for the day and Daylight Saving Time.

PROGRAMMING CONFLICTS.

Switch Off commands have priority over switch On commands.

NOTES:

1. The timer is set according to the boiler operation.

When the timer is blowdown is

OFF

the boiler is

2. Timer must be powered up during programming

to display

On/Off

status.

3. During programming, if no button is pressed after

1 minute, the timer will revert back to Run mode.

and the

Page 13

Installation, Operation & Maintenance Manual

24-Hour and 7-Day Time Switches

PROGRAMMING

or electric steam boilers equipped with Automatic Blowdown Systems ES 81600, refer to the following instructions for time clock operation and settings.

Timer settings for blowdown operation are at the discretion of the owner/operator.

The weekly program dial shows the seven days of the week and AM/PM imprints for each day.

The time switch is set by pushing the captive trippers to the outer ring position for the entire period that the load is to be turned ON, i.e., 2 hours to each tripper on the 7-day dial. When the tripper is pushed to the inside, the switch is in the OFF position.

SETTING TIME

To set the current time and day of week, turn the minute hand clockwise. Do not set the time by rotating “Outer” Dial.

Turn the minute hand clockwise until the day of the week and the time of day on the outer dial is aligned with the triangle marker on the inner dial (two o'clock).

Example for 7-day program dial Monday 10:30 Turn the minute hand clockwise until Monday 10:30

is aligned with the triangle on the inner dial.

The hour and minute hand will show exactly 10:30.

FOR MANUAL OVERRIDE

Manual override can be accomplished at the discretion of the owner/operator as follows.

3-WAY MANUAL OVERRIDE SWITCH

I = permanent ON

= automatic

O = permanent OFF

Maintenance

CAUTIO N

DISCONNECT ALL ELECTRICAL POWER BEFORE WORKING ON BOILER.

ussman Electric Steam Boilers are designed for years of trou-

ble-free performance. To establish a good preventative maintenance program, we suggest that the facility maintenance person or engineer familiarize themselves with these simple rules.

Daily blowdown at pressure is essential for ideal boiler performance. Extended periods of operation may require more frequent blowdown. If the boiler is not equipped with an automatic blowdown, in order to safeguard the heating elements, it is recommended to turn both the main disconnect switch and the boiler switch to the off position before manually blowing down the boiler.

The sight glass should be checked frequently to assure the

boiler has adequate water.

The sight glass should be checked daily for damage (i.e.

scratches, erosion, leaks etc.) The sight glass should be replaced if damaged. (See insert.)

A monthly inspection should be made of the internal wiring.

Open the access door and check all electrical connections for tightness. Replace any wires that show signs of damage.

NOTE:

this maintenance procedure.

The electrical power MUST be shut off during

Heating element mounting bolts should be checked and

tightened to a torque of 22 ft.-lbs. If there are indications of steam leaks from an element, replace the element gasket.

A monthly check for leaks should be made; any loose or

damaged fittings should be tightened or replaced.

Every four months the boiler float control should be

checked for proper operation. The lower equalization column can be examined visually and manually to see if is clear and clean. If there are signs of scale or mineral deposit buildup the float control must be disassembled and cleaned.

One of the lower heating elements should be removed. If scale or mineral deposits have begun to form all elements should be removed cleaned and reinstalled using new element gaskets.

Operating and high limit pressure control operation should be checked. Pressure controls should be removed and cleaned if necessary. Water feed supply check valves should be inspected and replaced if necessary.

If the boiler is equipped with an electronic auxiliary low

water cut-off every four months the probe should be removed and checked for deposits. The probe should be cleaned and reinstalled.

HAZARD OF ELECTRIC SHOCK.

IMPORTANT: It is recommended that for periodic and effective blowdown,the override switch be set in the automatic setting.

Page 14

Installation, Operation & Maintenance Manual

Standard Equipment for ES & HU Optional Equipment

AUXILIARY LOW WATER CUT OFF

• For model ES & HU boilers PN ES81017MR (with manual reset).

Senses water level electronically using a resistance probe. When a low water condition is detected, the contactor control voltage circuit is interrupted and the heating elements are de-energized. When water level returns to proper levels voltage is restored to the contactor coils and the elements are re-energized. For controls with a manual reset button voltage to the contactor coils is not restored until the water level has returned to proper operating levels and the reset button is pushed. Do not depress the reset button before the correct water level is achieved.

LINE PRESSURE WATER FEED SYSTEM

• For model ES & HU boilers PN ES99117

Water feed system used to supply makeup water to the boiler when incoming water line pressure is 10 psig greater than the operating pressure of the boiler. Completely factory plumbed and wired; 0-100psig range; 1/2” NPT size. Consists of strainer, solenoid valve (120/1/50-60Hz), and check valve for automatic feed.

HIGH PRESSURE WATER FEED SYSTEM

• For model ES12-72 PN ES38002A

• For model ES100-180 PN ES38020A Used to supply makeup water and to maintain constant water level when the boiler operating pressure is equal to or greater than incoming water line pressure and condensate is not returned to the boiler.

• ES38002A – Range is 0 – 100 psig, 1/2” NPT size consisting of strainer, solenoid valve and 1/3 HP 120/1/60 motor and pump.

• ES38020A – Range is 0 – 125 psig, 3/4” NPT size consisting of strainer solenoid valve and 1/2 HP 120/1/60 motor and pump. These assemblies are mounted on rubber shocks and secured to a steel base mounting plate. These units require field plumbing and wiring to the boiler.

CONDENSATE RETURN SYSTEM

(see page 16)

• For model ES12-72 PN ES38083V; for model ES85-180 PN ES38084V.

These systems are used whenever condensed steam can be collected for reuse in the boiler. Returning the condensate to the boiler can save a significant amount of energy. The water returned is relatively free of corrosive minerals and carries a substantial amount of heat that does not have to be replenished. A vacuum breaker is required whenever a condensate return system is used.

Each system consists of a vertical condensate return tank, a motor and pump and support plumbing. A 1/2” inlet is located on the tank to accept make-up water. A vent fitting is located on the condensate tank top for atmospheric air venting. The return fitting is to be plumbed to the trapped condensate return line coming from the process.

A gauge glass and valve set are mounted on the side of the condensate tank. The tank has a ball check valve internally mounted, and a float arm and float ball assembly that serve mechanically allowing make-up water to enter the tank as the original supply is used. The pump discharge outlet is to be plumbed to the boiler check valve. The tank drain valve should be plumbed to a proper drain line. The motor is required to be wired to the boiler.

Page 15

Installation, Operation & Maintenance Manual

Optional Equipment

ACUUM BREAKER SYSTEMS

For model ES boilers PN ES89369

•

(cont.)

A vacuum breaker will prevent a boiler from flooding as a

result of the steam condensing internally and creating a vacuum after boiler shutdown. The breaker allows air to enter the boiler shell breaking the vacuum. This system is a must for boilers connected to a condensate return tank. The vacuum breaker consists of a spring-loaded disc and associated piping and is factory plumbed to the boiler.

AUTOMATIC BLOWDOWN SYSTEM

• Extends life of boiler

• Saves labor costs

• Starts the boiler automatically every day

• Shuts down the boiler every day

• Automatically blows down the boiler every day

• Completely programmable, can skip days, different start and shutdown times, different operational durations.

• ES81600 for all model boilers. A stainless steel, motor driven straight-through, self-clean-

ing ball valve with Teflon seats handles particles and dirty fluid without the use of an up-stream strainer or other cleaning device. A timer (Standard analog time clock is set for two hour time intervals, optional digital time clock can be programmed to one minute intervals.) and electronic time delay relay control the boiler and the blowdown valve. A pilot light indicates when the blowdown valve is open. The valve shall be plumbed to a proper drain or receptacle. An automatic blowdown system can be installed on any boiler, regardless of size operating pressure or operating duty cycle.

CONTROL VOLTAGE STEPDOWN TRANSFORMER

• Provides 120 Volt (220 Volt export) from main power supply. Factory wired and fused.

BLOWDOWN SEPARATORS

(see page 17)

• For models ES12-48 - PN BDT-ASME36

• For models ES60-180 PN BDT-ASME42 A separator accepts the flash steam and effluent from the

boiler blowdown and reduces the temperature and pressure to insure a safe discharge of water and sludge. Steam flash and pressure are absorbed and pass harmlessly to the outside via a vent. The separator design utilizes a water seal at the outlet, which permits the operator to introduce cold water from the bottom to mix with the hot water and boiler steam in the blowdown separator. This reduces outlet temperature to a safe discharge level.

These separators require specific plumbing from the boiler

blowdown valve and require connection to a cold water supply. (If the separator is less than half full of water after the boiler is blown down cold water must be added to bring the water level to the halfway mark before the next blowdown).

• 0-30 psig pressure gauge; 0-200F temperature gauge; water

sight gauge glass and valve set assembly are included.

MULTISTAGE LOAD PROGRESSIVE SEQUENCERS

Accurate control is provided by automatic progressive sequencing in the use of energy and minimizing wear on electrical components. The sequencers are designed to apply power progressively to larger KW boilers. A factory installed pressure sensitive sequential control reacting to steam boiler pressure progressive energizes or de-energizes heating elements through power contactors. A delay between sequencer steps before start-up and between each subsequent step eliminates power surges. Each sequencer is matched and factory pre- set to boiler system requirements. Electronic progressive sequencers give accurate control of multi-stage loads of the type used in steam boilers. Features include progressive sequencing (first on- first off) that equalizes the operating time of each load. Integral solid-state light emitting diodes show active stages. Should a power interruption occur, all elements are instantly deenergized for safety. Upon resumption of power the control will re-stage the loads one at a time.

Page 16

Condensate Return Systems

/2"

DIA COVER PLATE

EASY ACCESS FOR MAINTENANCE

ONDENSATE RETURN FLASH TUBE

OVERFLOW OUTLET 1" NPT (farside) O

VERFLOW (label)

IMPLE RUGGED LINKAGE

5" DIA UPPER FLOAT BALL 39011FB

SHUTOFF GATE VALVE

STRAINER CLEANOUT

ENT SAFETY BAR

LOAT VALVE

39010-F

/8"

SIGHT GLASS

99074-1

ITE GLASS ASSY

PN 99173C

/2" DRAIN VALVE

PUMP EASY ACCESS

1-1/4" VENT WITH SAFETY BAR

ENT (label)

1/2" COLD WATER INLET COUPLING

WITH #100 MESH STRAINER

ONDENSATE RETURN (label)

TOP VIEW

OLD WATER INLET

(

label)

LIMIT MAKEUP WATER PRESSURE TO TO 30 PSI MAXIMUM” (label)

/4" CONDENSATE

RETURN COUPLING

Models 38083V & 38084V

Installation, Operation & Maintenance Manual

Notes:

Motor/Pump is closed - Coupled design

Pump capacity as follows:

MODEL 38083V

___________________

PSIG HEAD GPM

___________________

54 125 ft. 3.2

___________________

75 175 ft. 2.9

___________________

97 225 ft. 2.7

___________________

Normal cold water level approximately 1/2 to 5/8 up to visible part of gauge glass.

_____________________________________________________________________________

MODEL Used on "A" "B" "C" "D" "E"` H.P. VOLT/PH/HZ

_____________________________________________________________________________

38083V ES12 - ES72 38-1/4" 18 14-1/4" 14 18 1/3 120 / 1 / 60

_____________________________________________________________________________

38084V ES100 - ES180 51-1/2" 18 14-1/4" 14 30 1/2 120 / 1/ 60

_____________________________________________________________________________

MODEL 38084V

___________________

PSIG HEAD GPM

___________________

54 125 ft. 4.6

___________________

75 175 ft. 4.3

___________________

97 225 ft. 4.0

___________________

PUMP MOTOR

Page 17

Installation, Operation & Maintenance Manual

Blowdown Separator Tanks- Specifications and Data

Models BDT-ASME 36, 42, 48, 54

Dimensions and Features Suggested Hook-Up to Boiler

Pressure Gauge

"E"Vent

Blowdown Separator

Ventto atmosphere must be full size

Blowdown Inlet

"B"Inlet

Water Gauge

"C" Drain

Temperature

Gauge

3/4"Coupling for Temperature Probe(opt.)

BOILER DIMENSIONS SHIPPING

_______________________________________________________________________

BDT-ASME36 0-5 18" 1" 2" 12" 2" 2" 14" 32" 125

_______________________________________________________________________

BDT-ASME42 6-25 24" 1" 2" 16" 2-1⁄2" 2" 18" 42" 230

_______________________________________________________________________

BDT-ASME48 26-59 30" 1-1⁄4" 2" 16" 3" 2" 18" 48" 260

_______________________________________________________________________

BDT-ASME54 60-100 38" 1-1⁄2" 3" 16" 4" 2" 18" 54" 290

________________________________________________

ABCDEFGHWEIGHT

Handhole Assembly 3"x4"

(exceptBDT-ASME 36)

"F"ColdWater Inlet

&WashoutDrain

Tempered

Blowdown

to Drain

From Boiler Blowdown Outlets

ColdWater Supply

DrainValve (closed duringnormal operator)

The Sussman Separator design incorporates a water seal at the outlet which permits the operator to introduce cold water from the bottom to mix with the hot water and boiler steam blowdown in the separator. This reduces the outlet temperature to a level that makes it safe for discharge.

NOTE:

1BHP is approximately 10KW.

Maximum Boiler Working Pressure: 250 psi

Maximum Blowdown Separator Pressure: 65 psi

Blowdown Separators are sized in accordance with National Board Standards

Standard Equipment

• 0-100 lb. Pressure Gauge

• 0-200˚ Temperature Gauge

• Water Level Gauge

Constructed in accordance with Section VII Division I ASME Boiler & Pressure Vessel Code

Page 18

Installation, Operation & Maintenance Manual

Specifications

__________________________________________

Boiler Bhp Lbs/Hr 3-Ph

Model No. KW Rating Steam** Volts*** Amps

__________________________________________

208 34

ES-12* 12 1.22 36.2 240 29

__________________________________________

ES-18* 18 1.84 54.2 240 44

__________________________________________

ES-24* 24 2.45 72.3 240 58

__________________________________________

ES-30 30 3.06 90.4 240 73

__________________________________________

ES-36 36 3.67 108 240 87

__________________________________________

ES-48 48 4.90 145 240 116

__________________________________________

ES-60 60 6.12 181 240 145

__________________________________________

ES-72 72 7.35 217 240 174

__________________________________________

ES-100 108 11.2 325 240 260

__________________________________________

ES-135 144 14.7 434 240 347

__________________________________________

ES-160 158 16.2 475

__________________________________________

ES-180 180 18.4 542

__________________________________________

* Single phase available ** Steam at 212°F with 50°F feed water. See page 19 for sizing. *** Other voltage available

480 15

208 50

480 22

208 67

480 29 208 84

480 37

208 100

480 44

208 134

480 58

208 167

480 73

208 200

480 87

208 300

480 130

208 400

480 173

240 379 480 190

240 434 480 217

Steam Gauge

Pressure/

Temperature

________________

Gauge Temperature

Pressure

________________

________________________

Chart

PSIG

15 179 82

10 192 89

5 203 95

0 212 100

1 215 102

3 221 105

5 227 111

9 237 114

11 241 119

15 250 121

17 253 123

19 257 125

21 260 127

23 264 129

25 267 131

27 270 132

29 273 134

31 275 135

33 278 137

35 281 138

37 283 139

39 286 141

41 288 142

43 290 143

45 292 144

47 295 146

49 297 147

51 299 148

53 300 149

55 303 151

60 308 153

65 312 156

70 316 158

75 320 160

80 324 162

85 327 164

90 331 166

95 335 168

100 338 170

F˚ C˚

Page 19

Installation, Operation & Maintenance Manual

Sizing

Use the following Table to determine KW Boiler rating when steam load and feedwater temperatures are known.

___________________________________________________________________

Feed Water

( F˚)

___________________________________________________________________

40 .3347 .3355 .3375 .3388 .3406 .3422 .3431 .3447 .3458 .3464 .3470

___________________________________________________________________

50 .3318 .3326 .3345 .3359 .3376 .3392 .3401 .3417 .3429 .3435 .3441

___________________________________________________________________

60 .3288 .3296 .3316 .3329 .3347 .3363 .3372 .3388 .3400 .3407 .3411

___________________________________________________________________

70 .3259 .3267 .3287 .3300 .3318 .3334 .3343 .3359 .3370 .3376 .3382

___________________________________________________________________

80 .3229 .3238 .3278 .3271 .3288 .3305 .3313 .3329 .3341 .3347 .3353

___________________________________________________________________

90 .3200 .3208 .3238 .3242 .3259 .3275 .3284 .3300 .3312 .3318 .3324

___________________________________________________________________

100 .3171 .3179 .3199 .3212 .3229 .3246 .3255 .3271 .3283 .3288 .3294

___________________________________________________________________

110 .3142 .3150 .3170 .3183 .3200 .3217 .3225 .3242 .3253 .3259 .3265

___________________________________________________________________

120 .3112 .3210 .3140 .3154 .3171 .3287 .3196 .3212 .3224 .3230 .3236

___________________________________________________________________

130 .3083 .3091 .3111 .3124 .3142 .3160 .3167 .3183 .3195 .3200 .3206

___________________________________________________________________

140 .3054 .3062 .3082 .3095 .3113 .3129 .3137 .3154 .3165 .3171 .3177

___________________________________________________________________

150 .3025 .3032 .3052 .3066 .3083 .3099 .3108 .3124 .3136 .3142 .3148

___________________________________________________________________

160 .2995 .3003 .3029 .3036 .3054 .3070 .3079 .3095 .3107 .3113 .3118

___________________________________________________________________

170 .2966 .2974 .2994 .3001 .3025 .3041 .3050 .3066 .3077 .3083 .3089

___________________________________________________________________

180 .2937 .2945 .2964 .2978 2995 .3011 .3020 .3036 .3048 .3054 .3060

___________________________________________________________________

190 .2907 .2915 .2935 .2948 .2966 .2982 .2981 .3007 .3019 .3025 .3030

___________________________________________________________________

200 .2878 .2886 .2906 .2919 .2937 .2953 .2962 .2978 .2989 .2995 .3001

___________________________________________________________________

0210 15 25 40 50 75 100 125 150

Example:

Note:

Need a boiler to produce 450 lbs. steam/hr. at 75 psig with the available feedwater temperature 50˚ F.

From the chart above, find .3417 KW/Lb. of steam 450 lbs. steam/hr. x .3417= 153.8 KW boiler required

Add 20% to required kW for contingencies

Page 20

Gauge Glass Installation

Installation, Operation & Maintenance Manual

IMPORTANT NOTE:

Read all warnings and instructions before performing installation or maintenance. Safety glasses and gloves should be worn at all times when working with or examining water gauge glass and connections. Pressure in generator to be at zero before proceeding. Improper installation or maintenance of gauge glass and connections can cause immediate or delayed breakage resulting in bodily injury and/or property damage.

Apply Teflon tape or pipe dope to pipe threads. Install top gauge fitting (fitting without a drain valve) into the uppermost tapping. Wrench tighten the fitting until it is snug and the glass outlet is pointing at five o'clock (about 1/8 turn from its final downward vertical position).

Install the bottom gauge fitting (the fitting with a drain valve) until it is snug and the glass outlet is pointing directly upward. Verify top and bottom fittings are threaded into the tappings the same number of turns (distance A= distance B).

Remove glass packing nut, friction washer (or packing gland, depending upon the model), and glass packing from the fittings, and place them, in the same order, on to both ends of the gauge glass. Push both packings about an inch up the gauge glass.

Gently insert one end of the glass into the top gauge fitting. Keeping the glass inside the top fitting, gently rotate the top gauge fitting clockwise until vertically aligned with the bottom gauge, then insert glass into bottom fitting until glass bottoms out on the shoulder inside the bottom fitting.

Carefully raise glass about 1/16" and slide lower glass packing down until the glass packing contacts the lower gauge fitting. DO NOT allow the glass to remain in contact with any metal!

Carefully slide upper glass packing up as far as possible.

Hand tighten both glass packing nuts, then tighten 1/2 turn more by wrench. Tighten only enough to prevent leakage. DO NOT OVER TIGHTEN! If any leakage should occur, tighten lightly, a quarter turn at a time, checking for leakage after each turn.

IMPORTANT NOTE:

Read all warnings and instructions before performing installation or maintenance.

Top Gauge Fitting

Guard Rod

Friction Washer

(or Packing Gland)

Bottom

Gauge Fitting

WARN I N G

Drain Valve

Safety glasses and gloves

Vessel Wall

Gauge Glass

Glass Packing Nut

Glass Packing

should be worn at all times when working with or examining water gauge glass and connections.

Pressure in generator to be at zero before proceeding.

Improper installation or maintenance of gauge glass and connections can cause immediate or delayed breakage resulting in bodily injury and/or property damage.

Page 21

Installation, Operation & Maintenance Manual

Gauge Glass Installation - Use and Care

O NOTs

• DO NOT use glass if it contains any scratches, chips, or any other visible signs of damage.

• DO NOT reuse any tubular glass or glass packings.

• DO NOT subject gauge glass to bending or torsional stresses.

• DO NOT over tighten glass packing nuts.

• DO NOT allow glass to touch any metal parts.

• DO NOT exceed the recommended pressure of the gauge or gauge glass.

• DO NOT clean the gauge or gauge glass while pressurized or in operation.

DO's

• DO verify proper gauge has been supplied.

• DO examine gauge glass and packings carefully for damage before installation.

• DO install protective guards and utilize automatic ball checks where necessary to help prevent injury

in case of glass breakage.

• DO inspect the gauge glass daily, keep maintenance records, and conduct routine replacements.

• DO protect glass from sudden changes in temperatures such as drafts, water spray, etc.

AINTENANCE

Examine the gauge glass regularly for any signs of clouding, scratching, erosion, or corrosion. The glass should be inspected daily until the need for replacement becomes apparent. This will help establish the routine inspection and routine replacement schedules.

CLEANING

Use commercial non-abrasive glass cleaners to keep glass clean. Use diluted acids such as Hydrochloric (muriatic) acid when regular cleaners do not seem to work. Do not use wire brushes or any other abrasive materials which could scratch the glass.

INSPECTION

Examine the surface of the glass for scratches, corrosion, chips, cracks, surface flaws, or nicks. To do this, shine a very bright concentrated light at an angle of about 45 degrees.A defective glass will glisten as the light strikes imperfections. Glass which appears cloudy or roughened, and will not respond to cleaning, should be replaced.

STORING

Keep gauge glass in original packaging until ready to install.

Page 22

Installation, Operation & Maintenance Manual

Element Replacement

READ INSTRUCTIONS COMPLETELY BEFORE STARTING WORK

CAUTIO N

McDonnell Miller low water cut-off and aux. low water cutoff (if supplied) is operating properly. The float chamber and lower equalizer column of the MM control must be completely clear of sludge or other foreign matter. Failure to do this may cause the immediate burn-out of the new elements. If the unit is probe equipped, check condition of the probes and isolator.

All elements are thoroughly checked before shipment The manufacturer cannot be responsible for burn-outs caused by a faulty low water cut-off.

The lower equalizer column can best be examined by breaking the unions on either side and then visually and manually examining the piping with your finger or probes to see if it is clear and clean.

Disconnect boiler from electric power supply at main safety switch or fuse panel.

Then turn boiler switch to “OFF" position.

Close water supply valve on incoming water supply line. Drain boiler completely of water.

Open boiler door to access heating element.

Disconnect wire (electric) leads connecting element to main power system of boiler.

Again, note wire connections to facilitate re-assembly. Proceed to remove and discard (6) bolts from flange.

IMPORTANT:

Remove and discard six (5/16"-18) bolts from flange. Do not reuse these bolts.

Thoroughly clean boiler flange of all foreign material. Be certain no part of old gasket

remains on flange.

Apply "Slic-Tite" Gasket Compound (or equal) to both surfaces of new gasket supplied

with replacement element. Proceed to install element flange assembly with gasket between boiler flange and element flange. In doing this, be careful to align flange holes so element wire connection terminals on element assembly are in line with previously disconnected wire leads to facilitate easy connections.

NOTE:

10.

11.

12.

Observe markings on element flange. Install element marking “TOP” on top.

Use only new element flange bolts. Tighten all (6) element flange bolts to a torque value

of 22 lb-ft each (see illustration).

Connect all wires to the terminals. Tighten all element terminals to a torque value of

20 lb-in each (see illustration). Make sure all wires are clean and bright to assure good electrical contact.

Check that the wires are correctly connected to the contactor terminals and are tightened

to a torque value of 45 lb-in. (see illustration). Make sure all wires are clean and bright to assure good electrical contact.

Open water valve to allow water supply to reach boiler feed mechanism.

As boiler automatically refills, observe the new flange assembly for possible leaks. If water is noticed, the bolts must be re-tightened. Before doing this, turn the boiler off at the main fuse safety switch.

When boiler reaches working pressure, check flange assembly again for leaks.

CAUTIO N

Before Installing your new elements be sure the

Boiler with McDonnell Miller

11⁄2”

Note the wire connections to facilitate re-assembly (see wiring schematic).

Follow maintenance instructions provided with the boiler.

1”Steam EqualizingPipe

Pumpand LowWater Control

Normal BoilerWater Line

Cut-Off Level isArrowMark

Blowdown Valve

1”Water Equalizing Pipe

Torque Values:

Torque Wrench

Element Flange Bolts: 22 lb-ft

Torque Wrench

Element Terminals: 20 lb-in

Torque Wrench

Contactor Terminals: see Torque chart

For I llustrat ive Purposes Only. Power wiri ng show n in appr oxi mate factory- ins talled l ocation

TORQUE VALUES

Element Flange Bolts 22 lb-ft Element Terminals 20 lb-in Contactor Terminals 50 amp 25 lb-in

60 amp 45 lb-in 75 amp 75 lb-in

Page 23

Installation, Operation & Maintenance Manual

Water Quality Information for Carbon Steel Boilers

For optimum results, the feedwater supply should be tested prior to initial start-up. If the mineral content exceeds the following recommended limits, various external treatment processes (water softener, reverse osmosis, etc.) may be used to correct the problem.

NOTE:

An analysis of the on-site boiler feedwater must be made by a recognized and reliable water treatment company to ascertain the existing condition and treatment required.

RECOMMENDED FEEDWATER QUALITY

HARDNESS, ppm 8 – 85 (~0.5 – 5 gpg) P-ALKALINITY, ppm 85 – 410 (~5 – 24 gpg) T-ALKALINITY, ppm 200 – 500 (~7 – 0 gpg) pH (strength of alkalinity) 8.0 – 11.4 SPECIFIC RESISTIVITY ~50k Ω cm (50,000 ohm-centimeter)

Blow down the boiler on at least a once-a-day basis. If boiler water or feed-water are outside the above limits, a more frequent blowdown is required.

Water quality can affect efficiency or result in boiler damage if neglected. Boiler feedwater contains impurities in solution and suspension. These impurities concentrate in the boiler since the steam generated is essentially pure. The concentration of these impurities increases as more feedwater is introduced into the boiler and steam is produced. If the suspended solids are allowed to concentrate beyond certain limits, a deposit or “scale” will form on the boiler’s internal surfaces. This deposit can interfere with proper boiler operation and cause boiler failure.

The concentration of these impurities is generally controlled by the feedwater quality and by blowdown. Blowdown refers to removing a portion of the boiler water with high solids concentration and replacing it with make-up water of a lower concentration.

Page 24

A Division of Sussman-Automatic Corporation

43-20 34th Street, Long Island City, NY 11101 • (718) 937-4500 1-800-238-3535 • Fax: (718) 937-4676 • email: [email protected]

www.sussmanboilers.com

M A D E I N U S A

PUR 101137 4.13