Bluetooth speaker
Model Name: BS01
FCC ID: 2ABFFBS01
User Manual
Thank you for buying the Bluetooth Speaker BS01. This speaker is designed to be
convenient, stylish and provide high quality audio playback from any Bluetooth
enabled audio device or wired only device.
The Bluetooth Speaker BS01 can also be used to receive telephone calls while in
use and will automatically pause the audio playback in order to receive the call and
when the call ends audio Playback will resume.
Please read this user guide thoroughly before use so that you can understand the
setup and functions.
Accessories
1. Line-In Audio cable
2. USB Charging cable
Overview
The speaker contain the following parts as shown
Switch the speaker on or off
1. To switch on: Press and hold the on/off button for 2 seconds, the Blue indicator
light will start to flash.
2. To switch of f: Press and hold the on/of f button for 2 seconds until the Red indicator
light displays briefly.
Connecting with Bluetooth
1. Hold down the on/off Button for 7 seconds and the Blue and Red indicator light
will flash quickly and you’ll hear an audio tone. The Speaker is ready to
connect to the device.
2. Go to the Bluetooth option in the settings of your Bluetooth Audio device or
Smartphone and in the list of Devices select BS01.
3. The speaker is now ready to use
Getting Started Guide
Two kinds of connections
1. Bluetooth wireless connection
2. 3.5mm audio cable connection
Connection indication
3.5mm audio cable connection
Plug one end of the 3.5mm audio cable into speaker audio AUX port on the speaker
and the other end into the device you want to connect.(such as mobile, MP3, ipad,
etc.)
LED indication status
Power on: Blue light flash 5 times
Power off: Red light flash 5 times.
Pairing: Blue and Red light flash quickly
Standby： Blue light flash 2 times every 7 seconds.
Incoming call： Blue light flash 1 times every 1 seconds
During a call： Blue light flash 1 times every 7 seconds
Charge: Red light remains on.
Charge finish: Red light turn to Blue.
Basic operation
1) Answer a call: After connection is successful, short press the MFB button to
answer an incoming call.you will hear an indication tone.
2) End a call: When the call is connected successfully , short press the MFB button
to hang up , with an indication tone.
3) Reject a call: Hold the MFB button for 3 seconds to reject an incoming call , you
will hear an indication tone.
4) Voice transfer: During a call , hold the MFB botton for 3 seconds until hear an
tone, then the voice begin to be transfered from the Bluetooth speaker to your
phone , the same operation can transfer the sound from your phone to a
Bluetooth speaker
5) Last number redial: In the standby mode , press the “Multi-function” button for 3
seconds will redial the last outgoing number. you will hear an indication tone.
6) Voice dial: In the standby mode, Double click the MFB button to start voice
dial,you will hear an indication tone.(Need the support of the mobile phone
Bluetooth)
7) Adjust the volume: when answering, dialing or during a call, short press “+” button
to increase volume, and you will hear an indication tone when increase to
maximum volume. Similarly, short press “-“ button to decrease the volume, and
also an indication tone when decrease to minimum volume.
8) Pause/Play/Next/Previous:
Pause / Play: Short press the multifunction button to play or pause music.
Previous / Next Song: During playing music, long press “+” button to play next
song and press “-” button to play previous song.
9) Automatic reconnection: The speaker will reconnect with the phone that paired
before when turn on.
Battery low-voltage alert
Red light will remains on during charging, will change to Blue light when charging
finished. It will take around 2 hours to finish charging. please charge the battery in
time When red light flash and alert tone sounds once every 1 minute.
Note:
1. Pairing mode will last 5 minutes. other mobile phone cannot search out the
bluetooth speaker.
2. Re-connecting automatically(includes two cases)
2.1 If the Bluetooth speaker turned off, it will connected to the pre-set Bluetooth
speaker automatically When turn on manually.
2.2 When the Bluetooth speaker disconnects to mobile phone owing to exceeding
effective range(normally Link loss if exceed 10M), the bluetooth speaker will
re-connect to mobile phone if back to effective range within about 5 minutes.
About battery
The Bluetooth speaker is powered by a rechargeable battery , new battery achieve
the best performance only after two or three complete charge and discharge cycles.
The battery can be charged and discharged hundreds of times , but it will eventually
wear. When not charging , disconnect it with Bluetooth speaker. Do not leave a fully
charged battery connected to a charging circuit since overcharging may shorten
battery life. If a fully charged battery is left unused, the battery itself will be discharged
after a period of time. If place the battery in hot or cold places , such as a closed car in
summer or winter , will reduce the battery capacity and lifetime. Battery temperature
should be maintained at between 15-25 centigrade. Bluetooth speaker battery too hot
or cold may make it not work temporarily , even if the battery is fully charged. Battery
performance is particularly limited in temperatures well below freezing . Do not
dispose of batteries in a fire in order to avoid battery explosion. Impaired batteries
may also explode.
Avoid placing this product near extreme temperatures or humidity.
Do not use this product while operating a motor vehicle
Do not submerse or allow this product to come into contact with water. Use in dry
locations only.
• An adult should supervise young children when using this product.
• Use of any attachment or accessory with this product not recommended or sold by
White Label may result in risk of fire, electrical shock or injury to persons or
product.
Do not clean any parts with alcohol, cleaning solutions containing alcohol or
strong abrasives. Use a soft cloth and a little water
There are no user serviceable parts within this product. Tampering with this
product will invalidate your warranty.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and,if not in-stalled and used in accordance with
the instruc-tions,may cause harmful nterference to radio communications.However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harm-ful interference to radio ortelevision
reception, which can be determined by turning the equip-ment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
.Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC NOTICE
This device complies with Part 15of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interfer-ence; and
2. This device must accept any interference received, including interference that may
cause.
FCC CAUTION
Any changes or modifcations not expressly approved by the party responsible for
compliance could void the user's authority tooperate this equipment.
• This device and its antenna(s) must not be co-located or operating in conjunction
with anyother antenna or transmitte
r.
Loading...