Surefine SF-LED16-80, SF-LED16-40, SF-LED16-120, SF-LED16-160, SF-LED16-200 Installation Instructions Manual

LED FLOOD LIGHTS

INSTALLATION INSTRUCTIONS

When using electrical equipment, basic safety precauons should always
be followed including the following:

IMPORTANT SAFEGUARDS

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

1.

2.

3.

4.

To avoid the possibility of electrical shock, turn off power supply before
installaon or servicing. Installaon and servicing should be performed
by qualified personnel.
Product must be installed in accordance with your local electrical code.
If you are not familiar with these codes and requirements, consult a
qualified electrician.
Do not change the structure or any commponents of the fixture to
ensure safety.
Lock the installaon angle aer luminaire installed. As following figure.

SAVE THIS INSTRUCTIONS FOR FUTURE REFERENCE

TO INSTALL:

DIRECT MOUNTING

1

*¹ Minimum M10 (3/8”) Bolts (not-provided)
*² Mounng Nuts are not provided
*³ Allen Wrench: 8mm (5/16”)

3

Assemble the mounng bracket to the fixture
by provided M10 (3/8”) round head screws.

STEP 1:

Quality You can

Trust

328 mm (12.91 inches)

40 mm (1.57 inches)

Φ12 mm (0.47 inches)

138 mm (5.43 inches)

12 mm (0.47 inches)

Mounng Bracket

81 mm

(3.19 inches)

75 mm

(2.95 inches)

Luminaire

Mounng Holes For
Minimum M10 (3/8”)
Mounng Bolts

Pendant
Mounng
Hole

Waterproof Connector

2

Celling /Wall

Mounng Blots*¹

Mounng Nuts*²

Power Cord
(Cord Not shown)

Power Cord
(Cord Not shown)

Allen Wrench*³

Mount the fixture by TWO(2) minimum M10
(3/8”) bolts. See Figure 2.

STEP 2:

Loosen the mounng bracket screws, adjust
the fixture to desire posion, re-secure the
screws.

STEP 3:

Connect the Power Cord to the supply wiring
per “Electrical ConnecƟons” secon for
compleng electrical connecons.

STEP 4:

Tighten bracket screws on both sides, luminaire
installaon angle will be fixed by the lock gear.

Model No.

SF-LED16-80

SF-LED16-40

SF-LED16-120

SF-LED16-160

SF-LED16-200

SF-LED16-240

40W

80W

120W

160W

200W

240W

Power

366 x340 x156 mm /14.4 x13.4 x6.1”

439 x340 x156 mm /19.4 x13.4 x6.1”

512 x340 x156 mm /20.2 x13.4 x6.1”

585 x340 x156 mm /23.0 x13.4 x6.1”

658 x340 x156 mm /26.0 x13.4 x6.1”

Dimension

4.3 kg /9.5 lbs

5.2 kg /11.5 lbs

6.0 kg /13.2 lbs

7.0 kg /15.4 lbs

7.8 kg /17.2 lbs

Weight

3.1 kg /6.8 lbs293 x340 x156 mm /11.5 x13.4 x6.1”

100-240V/277V AC, 50/60Hz, Suitable for Wet Locaons (IP65), Class I

*This product must be grounding

IMPORTANT

Check whether it concerns an AC(AlternaƟng Current) based system - 100-240V/277V AC, 50/60Hz.

This marking indicates that this product should not be disposed with other household wastes throughout the EU.
To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To return your used device, please use
the return and collecƟon systems or contact the retailer where the product was purchased. They can take
this product for environmental safe recycling.

ELECTRICAL CONNECTIONS - 100-240V/277V AC, 50/60Hz

PHASE TO NEUTRAL WIRING

STEP 1:

Make the following Electrical ConnecƟons:

a.

b.

c.

Connect INPUT GROUND conductor to GREEN WIRE posiƟon
of the terminal block or GROUND conductor of LED driver.
Connect INPUT VOLTAGE conductor to BROWN WIRE posiƟon
of the terminal block or LINE conductor of LED driver.
Connect INPUT NEUTRAL conductor to BLUE WIRE posiƟon
of the terminal block or NEUTRAL conductor of LED driver.

STEP 2:

Make sure all excess input wires are pushed into pole, screws are
Ɵghtened.

STEP 3:

Close cover by firmly pushing cover towards fixture, making sure
that no wires are pinched and Sealing gasket are fully engaged.

STEP 4:

If the fixture without a terminal block, please insulate all electrical
connecƟons with wire nuts suitable for at least 90°C

TERMINAL BLOCK(not-provided),
Use waterproof connector for wet locaƟon.

LED DRIVER

GROUND

GREEN

NEUTRAL

WHITE

NEUTRAL

BLUE

GROUND

YELLOW-GREEN

LINE

BLACK

LINE

BROWN

L

G

N

INPUT WIRING

FIXTURE WIRING

AC BASED

Input cable should be at least H05RN-F 3x1.0mm²(SJTW 18AWG) or
outdoor grade cable with rubber sheathed(not supplied). The cable
must have a minimum cross secƟonal area of 1.0mm²(18AWG).

*If the fixture with built-in 3 in 1 dimming funcƟon, please connect INPUT

POSITIVE(+) signal conductor to DIM+ (BLUE WIRE), INPUT NEGATIVE(-) signal
conductor to DIM-(WHITE WIRE) of LED driver.

WWW.SUREFINEGROUP.COM

Loosen the mounƟng bracket screws, adjust
the fixture to desire posiƟon, re-secure the
screws.

STEP 3:

Connect the Power Cord to the supply wiring
per “Electrical ConnecƟons” secƟon for
compleƟng electrical connecƟons.

STEP 4:

PENDANT MOUNTING

Assemble the mounƟng bracket to the fixture
by provided M10 (3/8”) round head screws.

STEP 1:

AƩach Lock-Nut(A) to the boƩom of the
Pendant Stem. AƩach Lock-Nut(B) by holding
the interjacent Fixture Bracket and Ɵghtening
Lock-Nut(B) unƟl secure. See Figure 4.

STEP 2:

4 5

Look-Nut(A)*²

Look-Nut(B)*²

Pendant Stem*¹

Pendant Stem Thread

*¹ Pendant Stem can not be the soŌ material (not-provided)
*² Look Nuts are not provided

Power Cord
(Cord Not shown)

Power Cord
(Cord Not shown)