Sure-Fi, Inc. DS004-BRIDGE, DS004-CONTROLLER, DS004-REMOTE Operator's Manual

1

SURE-FI, INC. | www.sure-fi.com

Sure-Fi Wiegand Bridge

Operators Manual

Doc #P10226 Rev 1.9

2

SURE-FI, INC. | www.sure-fi.com

Sure-Fi Wiegand Bridge

Quick Startup:

The two units that are packaged together (banded) are factory paired and
will only communicate with each other.

Check initial operation

Connect the 9V battery (included) to the 9V power cable (included) and plug the two-position
connector in to the Wiegand Controller / Remote Interfaces at the ‘12V’ and ‘GND’ positions on the
bottom edge connector. Once both units are powered up, the green POWER LED should be ON
steady on each unit. Press and quickly release the ‘TEST’ button to test communication between
the two units. One or more of the blue LEDs should light up for one second to indicate that
successful communication has occurred.

Perform a Range-Test from the desired install locations

With the 9V batteries plugged in to each of the units, place them at the desired install location
points and perform a Range-Test by pressing and quickly releasing the ‘TEST’ button. The received
signal strength is displayed for one second on the six blue LEDs with the bottom LED indicating the
minimum signal strength and all six LEDs indicating maximum signal strength.

Connect to permanent power

Before connecting each unit to the permanent power source, ensure that it is a 12VDC supply that
can source at least 1 ampere to the unit. Connect the power at each unit and perform several
Range-Tests to check for adequate input power.

Wire the input and output functions

Using the wiring examples on pages 21 – 27 for reference, wire the required devices at each unit.

3

SURE-FI, INC. | www.sure-fi.com

Sure-Fi Wiegand Bridge

Part Numbers

Pg. 5

Product Overview

Pg. 5

Features

Pg. 5

General Specifications

Pg. 6

Radio Transceiver Specifications

Pg. 6

Device Overview

Pg. 7

Controller Interface – Top & Bottom Connector pin descriptions

Pg. 8

Remote Interface – Top & Bottom Connector pin descriptions

Pg. 9

Providing Power to the Controller and Remote Interfaces

Pg. 10

Battery Backup Charging and UPS Functionality

Pg. 10

POWER LED and BATTERY LED Diagnostics

Pg. 11

Jumpers JP1 and JP2 (Remote Interface only)

Pg. 12

Relays

Pg. 13

Wiegand Port (D0, D1, LED), Wiegand LED

Pg. 13

Auxiliary (AUX IN / AUX OUT)

Pg. 14

Test (Range Test) Push Button

Pg. 14

LEDS: Power, Battery, Tx, Rx

Pg. 14

Antenna information

Pg. 14

Connector plug information

Pg. 14

Chain Multiple system pairs for extended range

Pg. 15

Mounting

Pg. 16 – 17

Sure-Fi APP – downloading, installing, connecting

Pg. 18

Sure-Fi APP – Firmware Updating

Pg. 18

Sure-Fi APP – Changing the name of the unit, Configuration of the Wiegand

LED

Pg. 19

Sure-Fi APP – Setting System Heartbeat, Relay Defaults, Timeout, and Alert

Relay(s)

Pg. 19
Troubleshooting, Wiegand problems, manually testing relays

Pg. 19 – 20

Wiring Examples

Pg. 21 – 27
FCC and Industry Canada Regulatory Statements

Pg. 28

Warranty

Pg. 29

Table of Contents

4

SURE-FI, INC. | www.sure-fi.com

Sure-Fi Wiegand Bridge

Figure 1: Device Overview

Pg. 7

Figure 2: Connecting Power and Backup Battery

Pg. 10

Figure 3: Jumpers JP1/JP2

Pg. 12

Figure 4: Diagram of Power Input, +VBUS, and JP1/JP2 functionality

Pg. 12

Figure 5: Chain multiple systems, wiring diagram

Pg. 15

Figure 6: DIN clips pressed outward for screw mounting

Pg. 16

Figures 7 & 8: Top and Bottom DIN Rail Screw Mount locations

Pg. 17

Figures 9 & 10: Wiring a Wiegand device

Pg. 21

Figures 11 & 12: Wiring a Mag-Lock that is powered with a wet relay contact

Pg. 22

Figures 13 & 14: Wiring a Door Position Sensor to Relay 3 (R3 IN)

Pg. 23

Figures 15 & 16: Wiring a Request to Exit (REX) button to Relay 4 (R4 IN)

Pg. 24

Figures 17 & 18: Wiring example for Door Strike, REX button, and Wiegand

device

Pg. 25

Figures 19 & 20: Wiring example for a Maglock, REX button, and Wiegand

device

Pg. 26
Figures 21 & 22: Wiring a Gate Operator, REX button, and Wiegand device

Pg. 27

Figure Reference Guide

5

SURE-FI, INC. | www.sure-fi.com

Sure-Fi Wiegand Bridge

DS004-BRIDGE

Wiegand Bridge system: includes 1 ea. DS004-CONTROLLER and DS004-REMOTE

DS004­CONTROLLER

Wiegand Controller Interface

DS004­REMOTE
(REV2)

Wiegand Remote Interface
Note: if the product part number includes ‘REV2’ such as ‘DS004-REMOTE
REV2’, then the relays are solid state type with the specifications noted on
page 6. Additionally, the relay outputs have on-board Surge Protectors which
eliminates the need for the use of the external ones that are supplied with the
REV1 systems.

Part Numbers

Product Overview

The Sure-Fi DS004 Wiegand Bridge System consists of two units that are factory paired and ready
to use out of the box with no configuration required. These units are the Controller Interface, Model
DS004-CONTROLLER, and the Remote Interface, Model DS004-REMOTE. The system provides a
wireless connection (bridge) from a remote location (door, gate, or relay device), to the controller
location, such as an Access Control Panel. The Controller Interface wires to the Access Control
Panel and communicates wirelessly to the Remote Interface, which is placed near any peripheral
Wiegand device (card reader / keypad / receiver) and/or any relay/switch activated device. Each
DS004-BRIDGE System consists of one Wiegand channel, two relay outputs and two relay inputs
for functions such as door monitor sensors/request to exit inputs or any other relay-controlled
function. Each unit has two relay outputs that correspond with the two relay inputs from the
paired unit. The relays can be used independently and exclusively, meaning that it is not necessary
to use the Wiegand input to use the relays. The Sure-Fi App provides for configuration, diagnostics,
and field firmware updates.

Features

• Includes complete wireless solution from Remote location (reader/door) to Controller location

• Range: up to 1 mile through obstructions and greater than 50 miles line-of-sight

• Chain multiple system pairs for extended range

• One Wiegand port (compatible with any Wiegand protocol up to 64 bit)

• Two relay outputs per side NO, NC, COM terminals (wet contacts available on the Remote

Interface)

• Two relay control inputs per side, i.e. Request to Exit input (REX), Door monitor input (DPS), etc.

• One Auxiliary digital input/output (0 to 5V input/output)

• Backup Battery charger and UPS function

• DIN rail mount or direct wall mount

• Sure-Fi APP connects via Bluetooth for diagnostics and firmware updates

6

SURE-FI, INC. | www.sure-fi.com

Sure-Fi Wiegand Bridge

General Specifications

Operating Voltage: 12VDC (9VDC to 15VDC)

Operating Current: @ 12VDC: 0.08A (idle), 0.3A (transmit)

Operating Power: 3.6 Watt (peak)

Battery backup: 12V sealed lead acid (SLA) type only (not included)

Battery Low Threshold: < 11VDC

Battery Charge Voltage: 13.75V maximum at standby charge

Battery Charge Current: Trickle charge, 0.125A maximum at low battery voltage level.

Relay Inputs (each unit): Two relay control inputs: dry contact or digital 0 to 5VDC
interface

Relays (both units, REV 1 type): Two Form C relays, 2A 220VDC / 250VAC. Maximum
switching power 60W/ 125VA. Maximum allowable combined current of both
relays 3A

Relays (Remote REV 2 type): Two Form C solid state relays, 2A 30VDC / 30VAC
Note: Maximum allowable combined current is 3A

Range: Up to 1 mile through obstructions. Greater than 50 miles line-of­sight
Can chain multiple system pairs for extended range

Encryption: AES128

Operating Temperature: -40°F to +185°F (-40°C to +85°C)

Storage Temperature: -67°F to +257°F (-55°C to +125°C)

Humidity: 0 to 95% non-condensing

Dimensions (L x W x H): 3.54” x 4.23” x 1.28” (90mm x 107mm x 32.5mm)

DIN mount type: 35mm DIN rail (DIN46277-3) / (DIN35)

Degree of Protection: IP20 to IEC/EN 60529

Radio Transceiver Specifications

Transmit Power: 1 Watt (30dBm)

Frequency Band: 902 – 928MHz

Channels: 72 (Frequency hopping)

Receiver Sensitivity: -133dBm

Link Budget: 163dB

7

SURE-FI, INC. | www.sure-fi.com

Sure-Fi Wiegand Bridge

Device Overview

Figure 1: Device Overview

8

SURE-FI, INC. | www.sure-fi.com

Sure-Fi Wiegand Bridge

Position

Description

1 (right)

R4 NC: Relay 4 Normally-Closed terminal

2

R4 COM: Relay 4 Common terminal

3

R4 NO: Relay 4 Normally-Open terminal

4

R2 IN: Relay 2 control: activates Relay 2 on
Remote unit

5

GND: - DC Ground

6

R1 IN: Relay 1 control: activates Relay 1 on Remote
unit

7

GND: - DC Ground

8

R3 NC: Relay 3 Normally-Closed terminal

9

R3 COM: Relay 3 Common terminal

10 (left)

R3 NO: Relay 3 Normally-Open terminal

Position

Description

1 (left)

+12VDC: + DC input

2

GND: - DC input

3

BAT+: Battery backup positive terminal ’+’ connection. 12V Sealed Lead Acid (SLA)
type battery only.

4

GND: - DC input

5

NC: Not Connected

6

GND: - DC input (Wiegand Ground connection)

7

D0: Wiegand D0 connection

8

D1: Wiegand D1 connection

9

LED: Device LED connection

10 (right)

AUX-OUT: This is an output on the CONTROLLER INTERFACE. It corresponds with
input AUX-IN on the REMOTE INTERFACE.

Controller Interface - Top connector

Table 1:

Controller Interface - Bottom connector

Table 2:

9

SURE-FI, INC. | www.sure-fi.com

Sure-Fi Wiegand Bridge

Position

Description

1 (right)

R2 NC: Relay 2 Normally-Closed terminal

2

R2 COM: Relay 2 Common terminal

3

R2 NO: Relay 2 Normally-Open terminal

4

R4 IN: Relay 4 control: activates Relay 4 on
Controller unit

5

GND: - DC input

6

R3 IN: Relay 3 control: activates Relay 3 on
Controller unit

7

GND: - DC input

8

R1 NC: Relay 1 Normally-Closed terminal

9

R1 COM: Relay 1 Common terminal

10 (left)

R1 NO: Relay 1 Normally-Open terminal

Position

Description

1 (left)

+12VDC: + DC input

2

GND: - DC input

3

BAT+: Battery backup positive terminal ’+’ connection. 12V Sealed Lead Acid (SLA)
type battery only.

4

GND: - DC input

5

VBUS: + voltage output for Wiegand device (See Figure 4)

6

GND: - DC input (Wiegand Ground connection)

7

D0: Wiegand D0 connection

8

D1: Wiegand D1 connection

9

LED: Device LED connection

10 (right)

AUX-IN: This is an Input on the REMOTE INTERFACE and corresponds with the output
AUX-OUT on the CONTROLLER INTERFACE.

Remote Interface - Top connector

Table 3:

Remote Interface - Bottom connector

Table 4: