EP-320G-TX/320G-TX1/320G-TXL
64/32-bit PCI 1000/100/10Mbps
Gigabit Ethernet Adapter
User's Guide
431320GTX1Z2
Introduction
This User's Guide is used for the 64/32-bit PCI
1000/100/10Mbps Gigabit Ethernet Adapter. It is
targeted at high performance adapter cards and
motherboards. It implements the PCI Rev. 2.1/2.2, 66/33
MHz, 64/32-bit PCI bus interface for host
communications with power management support.
Packet descriptors and data are transfered via busmastering, reducing the burden on the host CPU. It is a
Full-Duplex adapter connected to an Ethernet net- work
with a single connection over unshielded twisted pair
(UTP) cable or fiber cable connection. It can auto-sense
either 10 Mbps or 100 Mbps or 1000 Mbps by full
auto-detection.
Features
*Compliant with PCI 2.1/2.2, 33/66MHz, 32bit/64bit
*Fully compliant with IEEE802.3, IEEE802.3u,
IEEE802.3x
*Supports data rates from 10 Mbps to 1000 Mbps
*Embedded with 32K cache buffer
*Supports wake-on-LAN and remote wake-up
* Fully compliant with Microsoft NDIS5 (IP, TCP, UDP)
Checksum and Segmentation Task-offload to lowering
CPU utilization
* Supports IEEE 802.1Q VLAN tagging
*Auto-Negotiation supported for Auto-Detect
10/100/1000Mbps data rate and Full/Half-Duplex operation
mode
* Supports ACPI, PCI power management
Package Contents
* One Gigabit Ethernet PCI Adapter
* Driver Diskette (Including this Manual)
The Card Layout
MAC
Phone
Jack
LED
Low Profile:
LED Indicator
10/100 The LED is on when the card is connected
to 10Mbps or 100Mbps network.
ACT. The LED indicators flash when there
transmission of data occurring at the card.
1000 The LED is on when the card is connected
to 1000Mbps Network.
ACT. The LED indicators flash when there is
transmission of data occurring at the card.
Installation Procedures
Discharge any static electricity from your body before
handling the sensitive board of the card. Handle the card
by its edges, and be careful not to twist or flex it. Follow
the steps below to install the card:
•Unpack the card package.
•Switch off your computer's power.
Note: To prevent equipment damage and injury,
never apply the power when installing. Turn off any
devices that you may attach to the computer.
•Remove your computer's unit cover.
•Locate a free PCI local bus master slot.
•Remove the slot cover and screw.
•Insert the card into the chosen and correct slot
carefully.
•Put the computer's unit cover back.
Making Network Connection
Make sure the power to your computer is off to avoid
damage to both the computer and the network interface
card.
Using the RJ-45 plug and twisted-pair cable, connect the
network interface card to a 10BASE-T or 100 BASE-TX
or 1000 BASE-X HUB (concentrator). Note that the
maximum cable length between a hub and any computer
is 100 meters (328 feet).
Note: Make sure you have the correct wiring. To
reliably operate your network at 1000/100Mbps, you
must use unshielded twisted pair (UTP) Category 5
or better Data Grade wire. While Category 3 or 4
wire may initially seem to work, it will soon cause
data loss. The higher speed needs higher quality wire.
For 10 Mbps operation, you can use either UTP
Category 3, 4, or 5 Data Grade wire.
Setup Driver Program
README File
Driver setup to the card is described in the
README.TXT file found on the diskette provided.
Please take a few minutes to print and read this file so
that you don't miss any important notices.
Device Drivers on Diskette
The Driver Diskette contains several device drivers.
These drivers are described below. The utility diskette
also contains more updated information on configuring
and installing these drivers with the network operating
system of your choice.
NetWare This driver supports for Novell NetWare
server 4.x/5.x.
NDIS4 The NDIS 4 drivers are used by NT 4.0
NDIS5 The NDIS 5 drivers are used by Win98/
Win2000 /WinMe /Win XP.
UNIX SCO UNIX OpenSever 5 , FreeBSD 4.x/5.1
LINUX Linux systems with kernel 2.2/2.4.
MAC OS 10.2.x
Technical Specification
•PCI Local Bus Specification Rev. 2.1/2.2 or above
compliant computer.
•IEEE 802.3 10BASE-T,802.3u 100BASE-TX,
1000BASE-T standards.
•CSMA/CD topology.
•Operation Temperature: 0℃ to 70℃
Operating Humidity: 10% to 90% (non-condensing).
•Operation Voltage: + 5V +/- 5% @ 250mA.
Federal Communications Commission
Frequency Interference Statement
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions in this manual, may
cause interference to radio communications. This
equipment has been tested and found to comply with the
limits for a Class B computing device pursuant to
Subpart J of Part 15 of the FCC rules, which are
designed to provide reasonable protection against radio
interference when operated in a commercial
environment. Operation of this equipment in a
residential area is likely to cause interference, in which
case the user, at his own expense, will be required to
take whatever measures are necessary to correct the
interference.
CE Declaration of conformity
This equipment complies with the requirements relating
to electromagnetic compatibility, EN 55022 class B for
ITE and EN 50082-1. This meets the essential protection
requirements of the European Council Directive
89/336/EEC on the approximation of the laws of the
Member States relating to electromagnetic compatibility.
Trademarks
All company, brand, and product names are trademarks
or registered trademarks of their respective companies.
Warranty
1-Year Limited Warranty
Subject to the terms and conditions set forth herein,
SURECOM provides this Limited warranty for its
product only to the person or entity that originally
purchased the product from SURECOM or its authorized
reseller or distributor.
SURECOM warrants that the hardware portion of the
SURECOM products described below will be free from
material defects in workmanship and materials from the
date of original retail purchase of the product, for the
period set forth below applicable to the product type
(“Warranty Period”), except as otherwise stated herein.
1-Year Limited Warranty for the Product(s) is defined as
follows:
•Hardware (excluding fans) one (1) Year
•Spare parts and spare kits Ninety (90) days
•Software portion of the product (“Software”) Ninety
(90) days
Loading...