Surebonder 9773, 9772 Operating Instructions Manual
®
FPC Corporation - 355 Hollow Hill Drive - Wauconda, IL 60084
Phone: (847) 487- 4583 Fax: (847) 487-0174
website: www.surebonder.com e-mail: sales@surebonder.com
Read All Safety Rules and Instructions Carefully
Save this manual for Future Reference
1211
Operating Instructions
0
33
33° Clipped Head 3-1/2" Framing Nailer
Includes: 3 Allen wrenches, open/closed end 8mm wrench & oil
Model 9773 Framing Nailer
WARRANTY
If you have any problems with this tool, please call FPC Corporation
toll-free at 1-800-860-3838 before returning it to the place of purchase.
FPC Corporation warrants this product to be free from defects in material and
workmanship, under normal conditions of use and when used in accordance with
FPC operating instructions, for a period of 90 days from the date of purchase by the
user. Within the 90 day warranty FPC at its option shall repair or replace product.
Product must be returned at the distributor/user expense, either within warranty or
out. Repaired or replaced product will receive a 60 day warranty. USER MUST BE
USING THE PROPER NAILS FOR THIS WARRANTY TO BE VALID. WARRANTY IS
VOID IF INCORRECT TYPE OF NAILS ARE USED.
Clipped Head
Paper Tape
2”- 3-1/2”
Visit us at surebonder.com for our full line of products
THE SAFETY WARNINGS BELOW CANNOT COVER ALL POSSIBLE SITUATIONS THAT MAY
OCCUR. THESE BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO PROTECT
AGAINST PERSONAL INJURY TO THE OPERATOR OR OTHER PERSONNEL IN THE AREA, AS
WELL AS DAMAGE TO THE EQUIPMENT. READ AND UNDERSTAND THESE WARNINGS BEFORE
USING EQUIPMENT.
Keep tool away from children, and DO NOT allow children near work area. Do not allow children
or untrained personnel to handle this nailer.
DO NOT operate this nailer while tired, or under the influence of drugs, alcohol, or medication
that makes you drowsy.
Never point the nailer at yourself or others - always assume that the nailer is loaded, and
proceed with caution.
Wear safety glasses and ear protection. The nailer operator and all personnel in the work area
must wear safety glasses that protect the front and side, to avoid eye injury. Ear plugs should be
worn to avoid hearing damage.
If operator will be working in a situation where overhead work will be done (i.e. on a ladder,
stairs, or scaffolding) a hard hat must be worn.
Never wear loose clothing or jewelry because it can get caught in the moving parts of this nailer.
Make sure long hair is covered, to avoid getting it caught in nailer.
Keep the nailer pointed away from yourself and others at all times. Keep hands and all body parts
away from rear area of nailer (near air hose) to guard against injury. Keep hands and feet away
from firing head during use.
Keep proper balance and footing at all times - do not over-reach.
Never use oxygen, bottled gas or any type of combustible fuel as a power source - it can cause
an explosion and serious injury.
Do not use near flammable liquids or gases - the nailer sparks during operation, and could cause
an explosion and serious injury.
Use an air hose that will withstand at least 150 psi, OR 150% of the maximum pressure of the
compressor.
Never connect this tool to compressed air if the pressure could exceed 200 psi, as the nailer
could burst. Use only clean, dry, regulated compressed air, with pressure not exceeding 100 psi.
Do not use a non-relieving coupler with this nailer - if used, the nailer could remain charged with
air after disconnecting, and would still be able to drive a nail even after being disconnected. The
nailer and air hose must have a coupling so that all pressure is removed from the nailer when the
coupling is disconnected.
Do not depress the trigger or safety mechanism while loading nails - accidental firing of a nail
can occur. Keep your fingers away from the trigger when not firing nails. Always keep the nailer
pointed downward during loading.
Do not use an air hose that is too long - nailer operator can trip over it. Make sure all connections
are tight.
(WARNINGS continued next page)
Improper use of this nailer can result in death or serious injury.
This manual contains important information about product safety.
Read and understand this entire manual before operating this nailer
IMPORTANT SAFETY WARNINGS:
! DANGER
1
10
Dia. Part
Description
Description
No. No.
Description
O-RING 16*1.7
SCREW 5*16
4 9773-4
EXHAUST DEFLECTOR
GASKET
WASHER
8 9773-8 CAP
O-RING 40*2.65
WASHER
11 9773-11 PISTON RETAINER
O-RING56.7*2.9
SCREW 6*35
15 9773-15 PISTON HEAD
O-RING42.9*4.8
WASHER
21 9773-21 CYLINDER
SEAL,AIR
WASHER
26 9773-26
HOUSING LOWER REMOTE
O-RING 58*2
SPRING
29 977329 REMOTE HOUSING
BUMPER(A)
CONICAL SPRING
35 9773-35 TRIGGER
BUMPER(B)
REMOTE CORE
38 9773-38 BUSHING
O-RING16*1.8
RELEASING BLADE
44 9773-44 SAFETY COVER
O-RING19*2.3
SCREW 5*18
46 9773-46 CATCH SUPPORT(B)
O-RING5.6*1.8
WASHER
48 9773-48 CATCH SUPPORT(A)
O-RING8*1.8
NYLON NUT M5
49 9773-49 NO MAR PAD
O-RING 2.3*1.4
PIN 3*14
53 9773-53 GRIP
SEAL,AIR
SPRING
55 9773-55 BODY
O-RING 89*2.9
SPRING PIN 3*16
57 9773-57 GUIDE BODY
O-RING 62.5*2
SPRING PIN 3*32
61 9773-61 TAIL COVER
GASKET
SCREW 5*12
67 9773-67 MAGAZINE SUPPORT
SPRING PAD RETAINER
69 9773-69 TAIL COVER
SPACER
70 9773-70 RELEASING BLADE
WASHER
72 9773-72 FEEDER CLIP
SPRING
73 9773-73 MAGAZINE
SCREW 5*25
74 9773-74 MAGAZINE GASKET
WASHER
78 9773-78 PUSHER
SCREW 5*18
79 9773-79 ROLLER
FEEDER SHOE STOP
84 9773-84 AIR PLUG
Description
SCREW 8*25
85 9773-85 COLLAR
O-RING42.9*4.8
RIVET
43 9773-83 TRIGGER
PISTON HEAD
RIVET
DRIVER BLADE
PIN
STEEL BAR
STOPPER
SPRING
SPRING
PIN
SPRING
SCREW 4*8
WASHER
86
Seal Kit #9773-400
Fastener Kit #9773-420
PARTS
SOLD SEPERATELY
Diagram
Diagram
9
2135
No.
No.
3
1
191020
12
14616
7
253427
36
22
233124
32
334051
41
283730
39
505254
58
564262
45
47
16
18
Drive Pin Kit #9773-410
Kits Available-on www.surebonder.com
59
60
66
68
71
Diagram
63
No.
64
17
65
757677
80
81
83
82
9773 Parts List
9773-400 Seal Kit
9773-410 Drive Pin Kit
9773-420 Fastener Kit
Loading...