Supero X9DR3-LN4F+, X9DRi-LN4F+ User Manual
USER’S MANUAL
Revision 1.1c
X9DR3-LN4F+
X9DRi-LN4F+
Manual Revision 1.1c
Release Date: April 1, 2014
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2014 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America
The information in this user’s manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
and makes no commitment to update or to keep current the information in this manual, or to notify
any person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our Website at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and documentation, is the property of Supermicro and/or its licensors, and is supplied only under a license.
Any use or reproduction of this product is not allowed, except as expressly permitted by the terms
of said license.
IN NO EVENT WILL SUPER MICRO COMPUTER, INC. BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE
USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER MICRO COMPUTER, INC.
SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED
WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING,
INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between the manufacturer and the customer shall be governed by the laws of
Santa Clara County in the State of California, USA. The State of California, County of Santa Clara
shall be the exclusive venue for the resolution of any such disputes. Supermicro's total liability for
all claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your
own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”.
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.
Preface
This manual is written for system integrators, PC technicians and
knowledgeable PC users. It provides information for the installation and use of the
X9DR3-LN4F+/X9DRi-LN4F+ motherboard.
About This Motherboard
The Super X9DR3-LN4F+/X9DRi-LN4F+ motherboard supports dual Intel E5-
2600(v2) Series Processors (Socket R LGA 2011) that offer QPI (Intel QuickPath
Interface) Technology (V.1.1), providing point-to-point connection with a transfer
speed of up to 8.0 TG/s. With the C606/C602 chipset built in, the X9DR3/i-LN4F+
motherboard provides support for Intel® Management Engine (ME), Rapid Stor-
age Technology, Digital Media Interface (DMI), PCI-E Gen. 3.0, and up to 1866
MHz DDR3 memory, greatly enhancing system performance for high end server
platforms. This motherboard is ideal for HPC/Cluster/Database servers. Please
refer to our website (http://www.supermicro.com) for processor and memory sup-
port updates.
Manual Organization
Chapter 1 describes the features, specications and performance of the mother-
board. It also provides detailed information about Intel C606/C602 chipset.
Chapter 2 provides hardware installation instructions. Read this chapter when in-
stalling the processor, memory modules, and other hardware components into the
system. If you encounter any problems, see Chapter 3, which describes trouble-
shooting procedures for video, memory, and system setup stored in the CMOS.
Chapter 4 includes an introduction to the BIOS, and provides detailed information
on running the CMOS setup utility.
Appendix A provides BIOS Error Beep Codes.
Appendix B lists software installation instructions.
Preface
iii
iv
Conventions Used in the Manual
Pay special attention to the following symbols for proper system installation and to
prevent damage to the system or injury to yourself:
Warning: Important information given to ensure proper system installation or to prevent
damage to the components
Note: Additional information given to differentiate between various models
or provides information for correct system setup.
X9DR3-LN4F+/X9DRi-LN4F+ Motherboard User’s Manual
Preface
v
Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: +1 (408) 503-8000
Fax: +1 (408) 503-8008
Email: marketing@supermicro.com (General Information)
support@supermicro.com (Technical Support)
Web Site: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: +31 (0) 73-6400390
Fax: +31 (0) 73-6416525
Email: sales@supermicro.nl (General Information)
support@supermicro.nl (Technical Support)
rma@supermicro.nl (Customer Support)
Web Site: www.supermicro.com
Asia-Pacic
Address: Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
Zhonghe Dist., New Taipei City 235
Taiwan (R.O.C)
Tel: +886-(2) 8226-3990
Fax: +886-(2) 8226-3992
Email: support@supermicro.com.tw
Tel: +886-(2)-8226-3990
Web Site: www.supermicro.com.tw
vi
Table of Contents
Preface
Chapter 1 Overview
1-1 Overview ......................................................................................................... 1-1
1-2 Processor and Chipset Overview...................................................................1-11
1-3 Special Features ........................................................................................... 1-12
1-4 PC Health Monitoring .................................................................................... 1-12
1-5 ACPI Features ............................................................................................... 1-13
1-6 Power Supply ................................................................................................ 1-13
1-7 Super I/O ....................................................................................................... 1-14
1-8 Advanced Power Management ..................................................................... 1-14
Intel® Intelligent Power Node Manager (NM) (Available when the NMView
utility is installed in the system) .................................................................... 1-14
Management Engine (ME) ............................................................................ 1-14
1-9 Overview of the Nuvoton WPCM450 Controller ........................................... 1-15
Chapter 2 Installation
2-1 Standardized Warning Statements ................................................................. 2-1
Battery Handling .............................................................................................. 2-1
Product Disposal ............................................................................................. 2-3
2-2 Static-Sensitive Devices .................................................................................. 2-4
Precautions ..................................................................................................... 2-4
Unpacking ....................................................................................................... 2-4
2-3 Processor and Heatsink Installation................................................................ 2-5
Installing the LGA2011 Processor ................................................................. 2-5
Installing a Passive CPU Heatsink ................................................................. 2-9
Removing the Heatsink ................................................................................. 2-10
2-4 Installing and Removing the Memory Modules ..............................................2-11
Installing & Removing DIMMs ........................................................................2-11
Removing Memory Modules ..........................................................................2-11
2-5 Motherboard Installation ................................................................................ 2-16
Tools Needed ................................................................................................ 2-16
Location of Mounting Holes .......................................................................... 2-16
Installing the Motherboard ............................................................................ 2-17
2-6 Control Panel Connectors and I/O Ports ...................................................... 2-18
Back Panel Connectors and I/O Ports .......................................................... 2-18
Back Panel I/O Port Locations and Denitions ........................................... 2-18
Serial Ports ............................................................................................... 2-19
Video Connection ..................................................................................... 2-19
X9DR3-LN4F+/X9DRi-LN4F+ Motherboard User’s Manual
vii
Table of Contents
Universal Serial Bus (USB) ...................................................................... 2-20
Ethernet Ports .......................................................................................... 2-21
Unit Identier Switch ................................................................................ 2-22
Front Control Panel ....................................................................................... 2-23
Front Control Panel Pin Denitions............................................................... 2-24
NMI Button ............................................................................................... 2-24
Power LED .............................................................................................. 2-24
HDD LED .................................................................................................. 2-25
NIC1/NIC2 LED Indicators ....................................................................... 2-25
Overheat (OH)/Fan Fail/PWR Fail/UID LED ............................................ 2-26
Power Fail LED ........................................................................................ 2-26
Reset Button ........................................................................................... 2-27
Power Button ........................................................................................... 2-27
2-7 Connecting Cables ........................................................................................ 2-28
Power Connectors ................................................................................... 2-28
Fan Headers ............................................................................................. 2-29
Chassis Intrusion ..................................................................................... 2-29
Internal Speaker ....................................................................................... 2-30
Power LED/Speaker ................................................................................. 2-30
TPM Header/Port 80 ................................................................................ 2-31
Power SMB (I2C) Connector .................................................................... 2-32
Overheat/Fan Fail LED ............................................................................ 2-32
T-SGPIO 1/2 Headers .............................................................................. 2-33
DOM Power Connector ............................................................................ 2-33
IPMB ......................................................................................................... 2-34
2-8 Jumper Settings ............................................................................................ 2-35
Explanation of Jumpers ................................................................................ 2-35
GLAN Enable/Disable .............................................................................. 2-35
CMOS Clear ............................................................................................. 2-36
Watch Dog Enable/Disable ...................................................................... 2-36
VGA Enable .............................................................................................. 2-37
BMC Enable ............................................................................................ 2-37
Management Engine (ME) Recovery ...................................................... 2-38
Manufacture Mode Select ........................................................................ 2-38
2-9 Onboard LED Indicators ............................................................................... 2-39
GLAN LEDs .............................................................................................. 2-39
IPMI Dedicated LAN LEDs ....................................................................... 2-39
Onboard Power LED ............................................................................... 2-40
Rear UID LED ......................................................................................... 2-40
viii
BMC Heartbeat LED ................................................................................ 2-41
2-10 Serial ATA Connections ................................................................................. 2-42
Serial ATA (SATA) Ports ........................................................................... 2-42
SCU Ports ................................................................................................ 2-42
Chapter 3 Troubleshooting
3-1 Troubleshooting Procedures ........................................................................... 3-1
3-2 Technical Support Procedures ........................................................................ 3-5
3-3 Battery Removal and Installation .................................................................... 3-6
3-4 Frequently Asked Questions ........................................................................... 3-7
3-5 Returning Merchandise for Service................................................................. 3-8
Chapter 4 BIOS
4-1 Introduction ...................................................................................................... 4-1
4-2 Main Setup ...................................................................................................... 4-2
4-3 Advanced Setup Congurations...................................................................... 4-3
4-4 Event Logs .................................................................................................... 4-24
4-5 IPMI ............................................................................................................... 4-26
4-6 Boot ............................................................................................................... 4-28
4-7 Security ......................................................................................................... 4-30
4-8 Save & Exit ................................................................................................... 4-31
Appendix A BIOS Error Beep Codes
A-1 BIOS Error Beep Codes .................................................................................A-1
Appendix B Software Installation Instructions
B-1 Installing Software Programs ..........................................................................B-1
B-2 Conguring SuperDoctor® III .......................................................................... B-2
X9DR3-LN4F+/X9DRi-LN4F+ Motherboard User’s Manual
Chapter 1: Overview
1-1
Chapter 1
Overview
1-1 Overview
Checklist
Congratulations on purchasing your computer motherboard from an acknowledged
leader in the industry. Supermicro boards are designed with the utmost attention to
detail to provide you with the highest standards in quality and performance.
Please check that the following items have all been included with your motherboard.
If anything listed here is damaged or missing, contact your retailer.
The following items are included in the retail box:
• One (1) Supermicro Mainboard
• Two (2) Serial ATA cables (CBL-0044Lx2)
•Two (2) I-Pass to Serial ATA cables (CBL-097L-03 x2) (for X9DR3-F)
•One (1) I-Pass to Serial ATA cables (CBL-097L-03) (for X9DRi-F)
• One (1) I/O Shield (MCP-260-00042-0N)
• One (1) Quick Reference Guide (MNL-1258-QRG)
Note: For your system to work properly, please follow the links below to
download all necessary drivers/utilities and the user's manual for your
motherboard.
Supermicro product manuals: http://www.supermicro.com/support/manuals/
Product Drivers and utilities: ftp://ftp.supermicro.com/
If you have any questions, please contact our support team at support@supermicro.
com.
1-2
X9DR3-LN4F+/X9DRi-LN4F+ Motherboard User’s Manual
Motherboard Image
Note: All graphics shown in this manual were based upon the latest PCB
Revision available at the time of publishing of the manual. The motherboard
you've received may or may not look exactly the same as the graphics
shown in this manual.
Chapter 1: Overview
1-3
Motherboard Layout
Note: For the latest CPU/Memory updates, please refer to our website at
http://www.supermicro.com/products/motherboard/ for details.
JRK1
JF1
JPI2C1
JPW3
JPW2
JPW1
JSD1
SP1
J18
J17
JBAT1
JP6
JP7
JI2C2
JI2C1
JL1
JOH1
FANB
FANA
FAN4
FAN3
FAN2
FAN6
FAN1
SW1
J21
JBT1
LEM1
JWP1
JPG1
JWD1
JPL1
USB4/5
JTPM1
XDP-PCH
BIOS BOX
SAS0~3
SAS4~7
I-SATA0
I-SATA1
P2 DIMMF3
P2 DIMMF1
P2 DIMMF2
P2 DIMME3
P2 DIMME2
P2 DIMME1
P2 DIMMG1
P2 DIMMH1
P2 DIMMG3
P2 DIMMG2
P2 DIMMH2
P2 DIMMH3
COM1
USB6/7
UID
IPMI_LAN
Alaways populate DIMMx1 first
P1 DIMMA2
P1 DIMMA1
P1 DIMMB3
P1 DIMMB2
P1 DIMMB1
P1 DIMMA3
P1 DIMMC1
P1 DIMMC2
P1 DIMMC3
P1 DIMMD1
P1 DIMMD2
P1 DIMMD3
I-SATA5
I-SATA4
I-SATA3
I-SATA2
LAN2/4
VGA
XDP-CPU
COM2
BMC
CTRL
LAN1/3
USB 0/1
JPME2
PHY
FAN5
BIOS
LAN
CTRL
PCH
LE1
X9DR3-LN4F+/X9DRi-LN4F+
Alaways populate DIMMx1 first
USB9
SAS
CTRL
USB 2/3
JSTBY1
IPMB
1
1
JD1
JF2
LE2
JPB1
JBMC1
Rev. 1.10
JPME1
CPU1
CPU2
CPU1 Slot1 PCI-E 3.0 x16
CPU1 Slot2 PCI-E 3.0 x4 (in X8 slot)
CPU2 Slot6 PCI-E 3.0 x8
CPU2 Slot5 PCI-E 3.0 x16
CPU2 Slot4 PCI-E 3.0 x16
CPU1 Slot3 PCI-E 3.0 x16
1-4
X9DR3-LN4F+/X9DRi-LN4F+ Motherboard User’s Manual
Notes:
•See Chapter 3 for detailed information on jumpers, I/O ports and JF1 front panel
connections.
•" " indicates the location of "Pin 1".
•Jumpers/LED Indicators not indicated are for testing only. Also, components that
are not documented in this manual are reserved for internal use only.
•Use only the correct type of onboard CMOS battery as specied by the manufac-
turer. Do not install the onboard battery upside down to avoid possible explosion.
X9DR3-LN4F+/X9DRi-LN4F+ Quick Reference
JRK1
JF1
JPI2C1
JPW3
JPW2
JPW1
JSD1
SP1
J18
J17
JBAT1
JP6
JP7
JI2C2
JI2C1
JL1
JOH1
FANB
FANA
FAN4
FAN3
FAN2
FAN6
FAN1
SW1
J21
JBT1
LEM1
JWP1
JPG1
JWD1
JPL1
USB4/5
JTPM1
XDP-PCH
BIOS BOX
SAS0~3
SAS4~7
I-SATA0
I-SATA1
P2 DIMMF3
P2 DIMMF1
P2 DIMMF2
P2 DIMME3
P2 DIMME2
P2 DIMME1
P2 DIMMG1
P2 DIMMH1
P2 DIMMG3
P2 DIMMG2
P2 DIMMH2
P2 DIMMH3
COM1
USB6/7
UID
IPMI_LAN
Alaways populate DIMMx1 first
P1 DIMMA2
P1 DIMMA1
P1 DIMMB3
P1 DIMMB2
P1 DIMMB1
P1 DIMMA3
P1 DIMMC1
P1 DIMMC2
P1 DIMMC3
P1 DIMMD1
P1 DIMMD2
P1 DIMMD3
I-SATA5
I-SATA4
I-SATA3
I-SATA2
LAN2/4
VGA
XDP-CPU
COM2
BMC
CTRL
LAN1/3
USB 0/1
JPME2
PHY
FAN5
BIOS
LAN
CTRL
PCH
LE1
X9DR3-LN4F+/X9DRi-LN4F+
Alaways populate DIMMx1 first
USB9
SAS
CTRL
USB 2/3
JSTBY1
IPMB
1
1
JD1
JF2
LE2
JPB1
JBMC1
Rev. 1.10
JPME1
CPU1
CPU2
CPU1 Slot1 PCI-E 3.0 x16
CPU1 Slot2 PCI-E 3.0 x4 (in X8 slot)
CPU2 Slot6 PCI-E 3.0 x8
CPU2 Slot5 PCI-E 3.0 x16
CPU2 Slot4 PCI-E 3.0 x16
CPU1 Slot3 PCI-E 3.0 x16
Chapter 1: Overview
1-5
X9DR3-LN4F+/X9DRi-LN4F+ Jumpers
Jumper
Description Default Setting
JBT1
Clear CMOS See Chapter 2
JI2C1/JI2C2 SMB to PCI-E Slots Off (Normal)
JPB1 BMC Enabled Pins 1-2 (Enabled)
JPG1 VGA Enabled Pins 1-2 (Enabled)
JPL1 GLAN1/GLAN2 Enable Pins 1-2 (Enabled)
JPME1 Management Engine (ME)
Recovery Mode Enable
Pins 1-2 (Normal)
JPME2 Management Engine (ME)
Manufacture Select
Pins 1-2 (Normal)
JWD Watch Dog Pins 1-2 (Reset)
X9DR3-LN4F+/X9DRi-LN4F+ Connectors
Connectors Description
COM1/COM2 Backplane COM Port1/Front Accessible COM2 Header
CPU1 Slot1/Slot3
CPU2 Slot4/Slot5
PCI-E 3.0 x16 Slots
CPU2 Slot6 PCI-E 3.0 x8 Slot
CPU1 Slot2 PCI-E 3.0 x4 in x8 Slot
FAN1~6, FANA,
FANB
CPU/System Fan Headers
IPMB 4-pin External BMC I2C Header (for an IPMI Card)
I-SATA 0~5 Intel SB SATA Connectors 0~5
J17/J18 Serial-Link General_Purpose IO Headers (T-SGPIO 1/2)
JBAT1 Onboard CMOS Battery (See Chapter 3 for Used Battery Disposal)
JD1 Speaker/Power LED Indicator
JF1 Front Panel Control Header
JPI2C1 System Management SMBbus I2C Header
JL1 Chassis Intrusion
JOH1 Overheat/Fan Fail LED
JPI2C1 Power Supply SMBbus I2C Header
JPW1 ATX 24-Pin Power Connector (See Warning on Page 1-6.)
JPW2/JPW3 12V 8-Pin Power Connectors (See Warning on Page 1-6.)
JSD1 SATA DOM (Device_On_Module) Power Connector
JSTBY1 Standby Header
JTPM1 TPM (Trusted Platform Module)/Port 80
1-6
X9DR3-LN4F+/X9DRi-LN4F+ Motherboard User’s Manual
Warning: To prevent damage to the power supply or motherboard, please use a power
supply that contains a 24-pin and two 8-pin power connectors. Be sure to connect
these power supply connectors to the 24-pin power connector (JPW1) and two 8-pin
power connectors (JPW2, JPW3) on the motherboard. Failure in doing so will void the
manufacturer warranty on your power supply and motherboard.
KB/Mouse PS2 Keyboard/Mouse
LAN1/3, LAN2/4 G-bit Ethernet Ports 1/3, 2/4
(IPMI) LAN IPMI_Dedicated LAN
SP1 Onboard Buzzer (Internal Speaker)
USB 0/1 Back Panel USB 0/1
USB 2/3 Back Panel USB 2/3
USB 4/5, USB 6/7 Front Panel Accessible USB Connections 4/5, 6/7
USB 9 Front Panel Type A USB 9 Port
UID Switch UID (Unit Identier) Switch
VGA Backpanel VGA Port
X9DR3-LN4F+/X9DRi-LN4F+ LED Indicators
LED Description State Status
LE1 Standby PWR LED Green: On SB Power On
LE2 UID LED Blue Unit Identied
LEM1 BMC Heartbeat LED Green: Blinking Normal
Chapter 1: Overview
1-7
Motherboard Features
CPU
• Dual Intel
®
E5-2600(v2) Series Processors (Socket R
LGA 2011); each processor supports four full-width Intel
QuickPath Interconnect (QPI) links (with support of up to
25.6 GT/s per QPI link and with Data Transfer Rate of up
to 8.0 GT/s per direction).
Note: For E5-2600(v2) processor support, BIOS
version 3.0 or above is required.
Memory
• Integrated memory controller supports up to 1.5 TB
of Load Reduced (LRDIMM), 768 Gb of Registered
(RDIMM) or 128 GB of Unbuffered (UDIMM) ECC/Non-
ECC DDR3 800/1066/1333/1600/1866 MHz 240-pin
4-channel memory in 24 DIMM slots.
Note 1: 1866 MHz memory support is dependent
on Intel E5-2600v2 CPUs.
Note 2: For the latest memory updates, please
refer to the Tested Memory List posted on our
website (http://www.supermicro.com/products/
motherboard).
• Virtualization: VT-x, VT-d, and VT-c
Chipset
• Intel® C606/C602 Chipset
Expansion
• Four (4) PCI Express 3.0 x16 slots (CPU1 Slot1/Slot3,
CPU2 Slot4/Slot5)
• One (1) PCI Express 3.0 x8 slot (CPU2 Slot6)
• One (1) PCI Express 3.0x4 in x8 slot (CPU1 Slot2)
Slots
Graphics
• Winbond Matrox MGA 200 Video Controller
Network
• One Intel i350A Gigabit (100/1000 Mb/s) Ethernet Quad/
Dual-Channel Controller for LAN1~LAN4 ports.
• Winbond WPCM450R Baseboard Controller (BMC) sup-
ports IPMI_LAN 2.0
I/O Devices
SATA Connections
• SATA Ports Six (6): Two (2) SATA 3.0, Four (4)
SATA 2.0 Ports
Four (4) SATA 2.0 Ports from SCU
(X9DRi-LN4F+)
• RAID RAID 0, 1, 5, 10 (Windows)
RAID 0, 1, 5, 10 (Linux)
1-8
X9DR3-LN4F+/X9DRi-LN4F+ Motherboard User’s Manual
SCU Connections
• SCU SAS/
SATA2 Ports
0~3, 4~7 (X9DR3-LN4F+ Only)
• RAID RAID 0, 1, 10 (Windows/Linux)
Integrated IPMI 2.0
• IPMI 2.0 supported by the Winbond WPCM 450R
BMC
Serial (COM) Port
• Two (2) Fast UART 16550 Connection: 9-pin RS-
232 port
Keyboard/Mouse
• Backplane USB Keyboard/Mouse
VGA
• Backplane VGA Port
Peripheral
Devices
USB Devices
• Four (4) USB ports on the rear I/O panel (USB 0/1,
USB 2/3),
• Four (4) USB connections for front access (USB
4/5, USB 6/7),
• One (1) Type A USB connector for front access
(USB 9)
BIOS
• 16MB AMI Flash ROM
• APM 1.2, DMI 2.3, PCI 2.3, ACPI 1.0/2.0/3.0, USB
Keyboard, Plug & Play (PnP) and SMBIOS 2.3
Power
• ACPI/ACPM Power Management
Cong.
• Main switch override mechanism
• Keyboard Wake-up from Soft-Off
• Power-on mode for AC power recovery
• Intel
®
Intelligent Power Node Manager (NM) (Avail-
able when the NMView utility is installed in the
system)
• Management Engine (ME)
PC Health
CPU Monitoring
Monitoring
• Onboard voltage monitors for 1.8V, +3.3V, 3.3VSB,
+5V Standby, 1.35V, 1.5V, Chipset Voltage, and
Battery Voltage.
• CPU 6-Phase switching voltage regulator
Chapter 1: Overview
1-9
• CPU/System overheat LED and control
• CPU Thermal Trip support
• Thermal Monitor 2 (TM2) support
Fan Control
• Fan status monitoring with rmware thermal man-
agement via IPMI 2.0
• Low noise fan speed control
LED Indicators
• System/CPU Overheat LED
• Suspend-state LED
• UID/Remote UID LED
System
Management
• PECI (Platform Environment Conguration Interface)
2.0 support
• System resource alert via SuperDoctor® III
• Thermal Monitor 2 (TM2) support
• SuperDoctor® III, Watch Dog, NMI
• Chassis Intrusion Header and Detection
Dimensions
• 13.68" (L) x 13.05" (W) (347.47 mm x 331.47 mm)
Note 1: For IPMI Conguration Instructions, please refer to the Embedded
IPMI Conguration User's Guide available @ http://www.supermicro.com/
support/manuals/.
Note 2: Changing BMC log-in information is recommended during initial
system power-on. The default username is ADMIN and password is ADMIN.
For BMC best practices, please refer to: http://www.supermicro.com/products/
nfo/les/IPMI/Best_Practices_BMC_Security.pdf
1-10
X9DR3-LN4F+/X9DRi-LN4F+ Motherboard User’s Manual
System Block Diagram
Note: This is a general block diagram and may not exactly represent the
features on your motherboard. See the Motherboard Features pages for
the actual specications of each motherboard. 2. This block diagram is
intended for your reference only.
PROCESSOR
PROCESSOR
QPI
#1
DDR3 DIMM
#2
DDR3 DIMM
DDR3 DIMM
#3
DDR3 DIMM
DDR3 DIMM
#3
#2
#1
DDR3 DIMM
G
A
SSB
Intel C606/C602
PEG0
DMI
PEG1 [4:1]
USB
LPC
LAN
RJ45 RJ45
#1
SATA
SYSTEM
BIOS
CPU REAR
CPU FRONT
PEG1_8
PCI-E x16 Slot
USB
REAR
HDR 2X5
0,1
TPM HDR
TYPE-A
REAR
2,3
QPI
DDR3 DIMM
B
DDR3 DIMM
D
C
H
F
E
Socket 1
Socket 2
#1
#2
#3
#1
#2
#3
#1
#2
#3
#1
#2
#3
#1
#2
#3
#1
#2
#3
P0
P0
P1
P1
PE3 PE2 PE1 DMI
DMI
#2
PCI-E x8 Slot
PCI-E x16 Slot
#3
x4
x16
x16
x4
HDR 2X5
BMC VGA
VGA CONN
DDR III
PHY1
LAN
RTL8211
SPI
x1
RJ45 RJ45
#6
PCI-E x16 Slot
#5
PCI-E x16 Slot
#4
PCI-E x16 Slot
x16
x4
x4
[7.4]
[3.0]
SIO
W83527
A
B
C
A
B
C
A
B
C
A
B
C
A
B
C
A
B
C
A
B
C
A
B
C
4,5
6, 7
PE3
PE2
PE1
9
SATA
SCU
#1~#6
#1~#8
(For X9DR3
-LN4F+ Only)
(4 SATA2 for X9DRi
-LN4F+ Only)
Chapter 1: Overview
1-11
1-2 Processor and Chipset Overview
Built upon the functionality and the capability of the Intel E5-2600(v2) Series
Processors (Socket R LGA 2011) and the C606/C602 chipset, the X9DR3-LN4F+/
X9DRi-LN4F+ motherboard provides the performance and feature sets required
for dual_processor-based HPC/Cluster/Database servers.
With support of Intel QuickPath interconnect (QPI) Technology, the X9DR3-LN4F+/
X9DRi-LN4F+ offers point-to-point serial interconnect interface with a transfer
speed of up to 8.0 GT/s, providing superb system performance.
The C606/C602 chipset provides extensive IO support, including the following
functions and capabilities:
•PCI-Express Rev. 2.0 support
•PCI-Express Gen. 3 uplink supported by some SKUs
•ACPI Power Management Logic Support Rev. 3.0b or Rev. 4.0
•USB host interface backplane and front access support
•Intel Rapid Storage Technology supported
•Intel Virtualization Technology for Directed I/O (Intel VT-d) supported
•Intel Trusted Execution Technology supported
•Serial Peripheral Interface (SPI) Supported
•Digital Media Interface (DMI) supported
•Advanced Host Controller Interface (AHCI) supported
Note: For Intel E5-2600(v2) processor support, BIOS version 3.0 or above
is required.
1-12
X9DR3-LN4F+/X9DRi-LN4F+ Motherboard User’s Manual
1-3 Special Features
Recovery from AC Power Loss
The Basic I/O System (BIOS) provides a setting that determines how the system will
respond when AC power is lost and then restored to the system. You can choose for
the system to remain powered off (in which case you must press the power switch
to turn it back on), or for it to automatically return to the power-on state. See the
Advanced BIOS Setup section for this setting. The default setting is Last State.
1-4 PC Health Monitoring
This section describes the features of PC health monitoring of the motherboard.
This motherboard has an onboard System_Hardware_Monitor chip that supports PC
health monitoring. An onboard voltage monitor will scan the voltages for processor,
memory, chipset, and battery continuously. Once a voltage becomes unstable, a
warning is given, or an error message is sent to the screen. The user can adjust
the voltage thresholds to dene the sensitivity of the voltage monitor.
Fan Status Monitor with Firmware Control
The PC health monitor chip can check the RPM status of a cooling fan. The onboard
CPU and chassis fans are controlled by rmware thermal management via IPMI 2.0.
Environmental Temperature Control
A thermal control sensor monitors the CPU temperature in real time and will turn
on the thermal control fan whenever the CPU temperature exceeds a user-dened
threshold. The overheat circuitry runs independently from the CPU. Once the
thermal management rmware detects that the CPU temperature is too high, it will
automatically turn on the thermal fan control to prevent the CPU from overheating.
The onboard chassis thermal circuitry can monitor the overall system temperature
and alert the user when the chassis temperature is too high.
Note: To avoid possible system overheating, please be sure to provide
adequate airow to your system.
System Resource Alert
This feature is available when used with SuperDoctor® III in the Windows OS
environment or used with SuperDoctor II in Linux. SuperDoctor is used to notify
the user of certain system events. For example, you can congure SuperDoctor
to provide you with warnings when the system temperature, CPU temperatures,
Chapter 1: Overview
1-13
voltages and fan speeds go beyond a predened range.
1-5 ACPI Features
ACPI stands for Advanced Conguration and Power Interface. The ACPI specica-
tion denes a exible and abstract hardware interface that provides a standard
way to integrate power management features throughout a PC system, including
its hardware, operating system and application software. This enables the system
to automatically turn on and off peripherals such as CD-ROMs, network cards, hard
disk drives and printers.
In addition to enabling operating_system-directed power management, ACPI also
provides a generic system event mechanism for Plug and Play, and an operating
system-independent interface for conguration control. ACPI leverages the Plug and
Play BIOS data structures, while providing a processor architecture-independent
implementation that is compatible with Windows 7, Windows Vista and Windows
2008 Operating Systems.
Slow Blinking LED for Suspend-State Indicator
When the CPU goes into a suspend state, the chassis power LED will start blinking
to indicate that the CPU is in suspend mode. When the user presses any key, the
CPU will "wake up" and the LED will automatically stop blinking and remain on.
1-6 Power Supply
As with all computer products, a stable power source is necessary for proper and
reliable operation. It is even more important for processors that have high CPU
clock rates.
The X9DR3-LN4F+/X9DRi-LN4F+ motherboard accommodates 24-pin ATX power
supplies. Although most power supplies generally meet the specications required
by the CPU, some are inadequate. In addition, two 12V 8-pin power connections are
also required to ensure adequate power supply to the system. Your power supply
must also supply 1.5A for the Ethernet ports.
Warning: To prevent damage to the power supply or motherboard, please use a power
supply that contains a 24-pin and two 8-pin power connectors. Be sure to connect these
power supply connectors to the 24-pin (JPW1) and two 8-pin power connectors (JPW2,
JPW3) on the motherboard. Failure to do so will void the manufacturer warranty on
your power supply and motherboard.
It is strongly recommended that you use a high quality power supply that meets ATX
power supply Specication 2.02 or above. It must also be SSI compliant. (For more
information, please refer to the website at http://www.ssiforum.org/). Additionally, in
1-14
X9DR3-LN4F+/X9DRi-LN4F+ Motherboard User’s Manual
areas where noisy power transmission is present, you may choose to install a line
lter to shield the computer from noise. It is recommended that you also install a
power surge protector to help avoid problems caused by power surges.
1-7 Super I/O
The Super I/O supports two high-speed, 16550 compatible serial communication
ports (UARTs). Each UART includes a 16-byte send/receive FIFO, a programmable
baud rate generator, complete modem control capability and a processor interrupt
system. Both UARTs provide legacy speed with baud rate of up to 115.2 Kbps
as well as an advanced speed with baud rates of 250 K, 500 K, or 1 Mb/s, which
support higher speed modems.
The Super I/O provides functions that comply with ACPI (Advanced Conguration
and Power Interface), which includes support of legacy and ACPI power manage-
ment through an SMI or SCI function pin. It also features auto power management
to reduce power consumption.
1-8 Advanced Power Management
The following advanced power management features are supported by this moth-
erboard:
Intel® Intelligent Power Node Manager (NM) (Available
when the NMView utility is installed in the system)
The Intel® Intelligent Power Node Manager (IPNM) provides your system with
real-time thermal control and power management for maximum energy efciency.
Although IPNM Specication Version 1.5/2.0 is supported by the BMC (Baseboard
Management Controller), your system must also have IPNM-compatible Manage-
ment Engine (ME) rmware installed to use this feature.
Note: Support for IPNM Specication Version 1.5 or Vision 2.0 depends
on the power supply used in the system.
Management Engine (ME)
The Management Engine, which is an ARC controller embedded in the PCH, pro-
vides Server Platform Services (SPS) to your system. The services provided by
SPS are different from those provided by the ME on client platforms.
Chapter 1: Overview
1-15
1-9 Overview of the Nuvoton WPCM450 Controller
The Nuvoton WPCM450R Controller, a Baseboard Management Controller (BMC),
supports 2D/VGA-compatible Graphic Cores with PCI interface, creating multi-media
virtualization via Keyboard/Video/Mouse Redirection (KVMR). The WPCM450R
Controller is ideal for remote system management.
The WPCM450R Controller interfaces with the host system via PCI connections
to communicate with the graphics cores. It supports USB 2.0 and 1.1 for remote
keyboard/mouse/virtual media emulation. It also provides LPC interface support to
control Super IO functions. The WPCM450R Controller is connected to the network
via an external Ethernet PHY module or shared NCSI connections.
The WPCM450R communicates with onboard components via six SMBus inter-
faces, PECI (Platform Environment Control Interface) buses, and General Purpose
I/O ports.
Other Features Supported by the WPCM BMC Controller
The WPCM450R supports the following features:
•IPMI 2.0
•Serial over LAN
•KVM over LAN
•LAN Alerting-SNMP Trap
•Event Log
•X-Bus parallel interface for I/O expansion
•Multiple ADC inputs, Analog and Digital Video outputs
•SPI Flash Host BIOS and rmware bootstrap program supported
•Reduced Media Independent Interface (RMII)
•OS (Operating System) Independency
•Provides remote Hardware Health Monitoring via IPMI. Key features
1-16
X9DR3-LN4F+/X9DRi-LN4F+ Motherboard User’s Manual
•Provides Network Management Security via remote access/console redirection.
•Supports the following Management tools: IPMIView, CLI (Command Line
Interface)
•RMCP+ protocol supported
Note 1: For more information on IPMI conguration, please refer to the
IPMI User's Guide posted on our website at http://www.supermicro.com/
support/manuals/.
Note 2: The term "IPMI controller" and the term "BMC controller" can be
used interchangeably in this section.
Chapter 2: Installation
2-1
Chapter 2
Installation
2-1 Standardized Warning Statements
The following statements are industry-standard warnings, provided to warn the user
of situations which have the potential for bodily injury. Should you have questions or
experience difculty, contact Supermicro's Technical Support department for assis-
tance. Only certied technicians should attempt to install or congure components.
Read this section in its entirety before installing or conguring components in the
Supermicro chassis.
Battery Handling
Warning!
There is a danger of explosion if the battery is replaced incorrectly. Replace the
battery only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's instructions
電池の取り扱い
電池交換が正しく行われなかった場合、破裂の危険性があります。 交換する電池はメー
カーが推奨する型、または同等のものを使用下さい。 使用済電池は製造元の指示に従
って処分して下さい。
警告
电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更
换原有电池。请按制造商的说明处理废旧电池。
警告
電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有
電池。請按照製造商的說明指示處理廢棄舊電池。
Warnung
Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die
Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp.
Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.
2-2
X9DR3-LN4F+/X9DRi-LN4F+ Motherboard User’s Manual
Attention
Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer
que par une pile de type semblable ou équivalent, recommandée par le fabricant.
Jeter les piles usagées conformément aux instructions du fabricant.
¡Advertencia!
Existe peligro de explosión si la batería se reemplaza de manera incorrecta. Re-
emplazar la batería exclusivamente con el mismo tipo o el equivalente recomen-
dado por el fabricante. Desechar las baterías gastadas según las instrucciones
del fabricante.
!הרהזא
תנכס תמייקץוציפ .הניקת אל ךרדב הפלחוהו הדימב הללוסה לש ףילחהל שי
גוסב הללוסה תא מ םאותה תרבחלמומ ןרציתצ.
תוללוסה קוליס תושמושמה עצבל שי .ןרציה תוארוה יפל
경고!
배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와 동일
하거나 제조사에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다. 제조사
의 안내에 따라 사용된 배터리를 처리하여 주십시오.
Waarschuwing
Er is ontplofngsgevaar indien de batterij verkeerd vervangen wordt. Vervang de
batterij slechts met hetzelfde of een equivalent type die door de fabrikant aan-
bevolen wordt. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften
afgevoerd te worden.
Chapter 2: Installation
2-3
Product Disposal
Warning!
Ultimate disposal of this product should be handled according to all national laws
and regulations.
製品の廃棄
この製品を廃棄処分する場合、国の関係する全ての法律・条例に従い処理する必要が
ありま す。
警告
本产品的废弃处理应根据所有国家的法律和规章进行。
警告
本產品的廢棄處理應根據所有國家的法律和規章進行。
Warnung
Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen
des Landes erfolgen.
¡Advertencia!
Al deshacerse por completo de este producto debe seguir todas las leyes y regla-
mentos nacionales.
Attention
La mise au rebut ou le recyclage de ce produit sont généralement soumis à des
lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de
l'organisme compétent.
2-4
X9DR3-LN4F+/X9DRi-LN4F+ Motherboard User’s Manual
2-2 Static-Sensitive Devices
Electrostatic Discharge (ESD) can damage electronic com ponents. To avoid dam-
aging your system board, it is important to handle it very carefully. The following
measures are generally sufcient to protect your equipment from ESD.
Precautions
•Use a grounded wrist strap designed to prevent static discharge.
•Touch a grounded metal object before removing the motherboard from the
antistatic bag.
•Handle the board by its edges only; do not touch its components, peripheral
chips, memory modules or gold contacts.
•When handling chips or modules, avoid touching their pins.
•Put the motherboard and peripherals back into their antistatic bags when not
in use.
•For grounding purposes, make sure that your system chassis provides excellent
conductivity between the power supply, the case, the mounting fasteners and
the motherboard.
Unpacking
The motherboard is shipped in antistatic packaging to avoid static damage. When
unpacking the board, make sure that the person handling it is static protected.
Chapter 2: Installation
2-5
OPEN 1st
WARNING!
2-3 Processor and Heatsink Installation
Warning: When handling the processor package, avoid placing direct pressure on
the label area.
Notes:
•Always connect the power cord last, and always remove it before adding,
removing or changing any hardware components. Make sure that you install
the processor into the CPU socket before you install the CPU heatsink.
•If you buy a CPU separately, make sure that you use an Intel-certied multi-
directional heatsink only.
•Make sure to install the system board into the chassis before you install
the CPU heatsink.
•When receiving a server board without a processor pre-installed, make sure
that the plastic CPU socket cap is in place and none of the socket pins are
bent; otherwise, contact your retailer immediately.
•Refer to the Supermicro website for updates on CPU support.
Press down
on
Load Lever
labeled 'Open 1st'.
Installing the LGA2011 Processor
1. There are two load levers on the LGA2011 socket. To open the socket cover,
rst press and release the load lever labeled 'Open 1st'.
OPEN 1st
WARNING!
1
2
2-6
X9DR3-LN4F+/X9DRi-LN4F+ Motherboard User’s Manual
Gently push
down to pop the
load plate open.
2. Press the second load lever labeled 'Close 1st' to release the load plate that
covers the CPU socket from its locking position.
3. With the lever labeled 'Close 1st' fully retracted, gently push down on the
'Open 1st' lever to open the load plate. Lift the load plate to open it com-
pletely.
OPEN 1st
WARNING!
OPEN 1st
WARNING!
1
2
Press down on
Load the
Lever labeled 'Close 1st'
WARNING!
OPEN 1st
WARNING!
1
Pull lever away from
the socket
2
Loading...