Supero Super X9DBL-i, X9DBL-3, X9DBL-iF, X9DBL-3F User Manual

USER’S MANUAL

Revision 1.0a

X9DBL-3

X9DBL-3F

X9DBL-i

X9DBL-iF

Manual Revision 1.0a

Release Date: March 9, 2013

Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.

Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.

Copyright © 2013 by Super Micro Computer, Inc.
All rights reserved.

Printed in the United States of America

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
and makes no commitment to update or to keep current the information in this manual, or to notify
any person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our Website at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and docu­mentation, is the property of Supermicro and/or its licensors, and is supplied only under a license.
Any use or reproduction of this product is not allowed, except as expressly permitted by the terms
of said license.

IN NO EVENT WILL SUPER MICRO COMPUTER, INC. BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE
USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER MICRO COMPUTER, INC.
SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED
WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING,
INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between the manufacturer and the customer shall be governed by the laws of
Santa Clara County in the State of California, USA. The State of California, County of Santa Clara
shall be the exclusive venue for the resolution of any such disputes. Supermicro's total liability for
all claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your
own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”.

WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.

X9DBL-i/3/iF/3F Motherboard User’s Manual

Preface

This manual is written for system integrators, PC technicians and

knowledgeable PC users. It provides information for the installation and use of the

X9DBL-i/3/iF/3F motherboard.

About This Motherboard

The Super X9DBL-i/3/iF/3F motherboard supports dual Intel E5-2400 Series

(Socket B2) processors and Intel QPI (QuickPath Interface) Technology (V.1.1),

providing point-to-point connections with transfer speeds of up to 8.0 TG/s. With

the C606/C602 chipset built in, the X9DBL-i/3/iF/3F motherboard supports Intel®

Manageability Engine (ME), Rapid Storage Technology, Digital Media Interface

(DMI), PCI-E Gen. 3.0, and DDR3 memory of up to 1600 MHz. These features

greatly enhance system performance. This motherboard is ideal for high-end server

platforms. Please refer to our Website at http://www.supermicro.com for processor

and memory support.

Manual Organization

Chapter 1 describes the features, specications and performance of the mother-

board. It also provides detailed information on the Intel C606/C602 chipset.

Chapter 2 provides hardware installation instructions. Read this chapter when in-

stalling the processor, memory modules, and other hardware components into the

system. If you encounter any problems, see Chapter 3, which describes trouble-

shooting procedures for video, memory, and system setup stored in the CMOS.

Chapter 4 includes an introduction to the BIOS, and provides detailed information

on running the CMOS Setup utility.

Appendix A provides BIOS Error Beep Codes.

Appendix B lists software installation instructions.

Preface

iii

iv

Conventions Used in the Manual

Pay special attention to the following symbols for proper system installation and to

prevent damage to the system or injury to yourself:

Warning: Important information is given to ensure proper system installation or to avoid

damaging system components

Note: Additional information is given to differentiate between various

models or to provide information for correct system setup.

X9DBL-i/3/iF/3F Motherboard User’s Manual

Preface

v

Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: [phone]

Fax: [phone]

Email: [e-mail] (General Information)

[e-mail] (Technical Support)

Web Site: www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

Tel: [phone]

Fax: [phone]

Email: [e-mail] (General Information)

[e-mail] (Technical Support)

[e-mail] (Customer Support)

Asia-Pacic

Address: Super Micro Computer, Inc.

4F, No. 232-1, Liancheng Rd

Chung-Ho Dist., New Taipei City 235

Taiwan

Tel: [phone]

Fax: [phone]

Web Site: www.supermicro.com.tw

Technical Support:

Email: [e-mail]

Tel: [phone]

vi

Table of Contents

Preface

Chapter 1 Overview

1-1 Overview ......................................................................................................... 1-1

1-2 Processor and Chipset Overview...................................................................1-11

1-3 Special Features ........................................................................................... 1-12

1-4 PC Health Monitoring .................................................................................... 1-12

1-5 ACPI Features ............................................................................................... 1-13

1-6 Power Supply ................................................................................................ 1-13

1-7 Super I/O ....................................................................................................... 1-14

1-8 Advanced Power Management ..................................................................... 1-14

Intel® Intelligent Power Node Manager (IPNM) ............................................ 1-14

Manageability Engine (ME) ........................................................................... 1-15

1-9 Introduction to the IPMI Controller (For X9DBL-iF/3F only) ......................... 1-15

WPCM450R DDR2 Memory Interface .......................................................... 1-15

WPCM450R PCI System Interface ............................................................... 1-15

Other Features Supported by the WPCM BMC Controller ........................... 1-15

Chapter 2 Installation

2-1 Standardized Warning Statements ................................................................. 2-1

2-2 Static-Sensitive Devices .................................................................................. 2-4

2-3 Processor and Heatsink Installation................................................................ 2-5

Installing an LGA 1356 Processor .................................................................. 2-5

Installing a Passive CPU Heatsink ................................................................. 2-7

Removing the Heatsink ................................................................................... 2-8

2-4 Installing and Removing the Memory Modules ............................................... 2-9

Installing & Removing DIMMs ......................................................................... 2-9

Removing Memory Modules ........................................................................... 2-9

2-5 Motherboard Installation ................................................................................ 2-13

Tools Needed ................................................................................................ 2-13

Location of Mounting Holes .......................................................................... 2-13

Installing the Motherboard ............................................................................ 2-14

2-6 Control Panel Connectors and I/O Ports ...................................................... 2-15

Back Panel Connectors and I/O Ports .......................................................... 2-15

Back Panel I/O Port Locations and Denitions ........................................... 2-15

ATX PS/2 Keyboard and Mouse Ports ..................................................... 2-16

Universal Serial Bus (USB) ...................................................................... 2-16

Serial Ports ............................................................................................... 2-17

X9DBL-i/3/iF/3F Motherboard User’s Manual

vii

Table of Contents

Video Connection ..................................................................................... 2-17

Ethernet Ports .......................................................................................... 2-18

Unit Identier Switch ................................................................................ 2-19

Front Control Panel ....................................................................................... 2-20

Front Control Panel Pin Denitions............................................................... 2-21

NMI Button ............................................................................................... 2-21

Power LED .............................................................................................. 2-21

HDD LED .................................................................................................. 2-22

NIC1/NIC2 LED Indicators ....................................................................... 2-22

Overheat (OH)/Fan Fail/PWR Fail/UID LED ............................................ 2-23

Power Fail LED ........................................................................................ 2-23

Reset Button ........................................................................................... 2-24

Power Button ........................................................................................... 2-24

2-7 Connecting Cables ........................................................................................ 2-25

Power Connectors ................................................................................... 2-25

Fan Headers ............................................................................................. 2-26

Chassis Intrusion ..................................................................................... 2-26

Internal Buzzer ......................................................................................... 2-27

Overheat/Fan Fail LED ............................................................................ 2-27

TPM Header/Port 80 ................................................................................ 2-28

IPMB ......................................................................................................... 2-28

Power SMB (I2C) Connector .................................................................... 2-29

Standby Header ....................................................................................... 2-29

T-SGPIO 1/2 & SCU-SGPIO 1/2 Headers ............................................... 2-30

Power LED/Speaker ................................................................................. 2-31

2-8 Jumper Settings ............................................................................................ 2-32

Explanation of Jumpers ................................................................................ 2-32

GLAN Enable/Disable .............................................................................. 2-32

CMOS Clear ............................................................................................. 2-33

Watch Dog Enable/Disable ...................................................................... 2-33

VGA Enable .............................................................................................. 2-34

BMC Enable ............................................................................................ 2-34

2-9 Onboard LED Indicators ............................................................................... 2-36

GLAN LEDs .............................................................................................. 2-36

IPMI Dedicated LAN LEDs ....................................................................... 2-36

Onboard Power LED ............................................................................... 2-37

Rear UID LED ......................................................................................... 2-37

BMC Heartbeat LED ................................................................................ 2-38

2-10 Serial ATA Connections ................................................................................. 2-39

viii

Serial ATA Ports........................................................................................ 2-39

SCU-SATA/SAS Ports .............................................................................. 2-39

Chapter 3 Troubleshooting

3-1 Troubleshooting Procedures ........................................................................... 3-1

3-2 Technical Support Procedures ........................................................................ 3-5

3-3 Battery Removal and Installation .................................................................... 3-6

Battery Removal .............................................................................................. 3-6

Proper Battery Disposal .................................................................................. 3-6

Battery Installation ........................................................................................... 3-6

3-4 Frequently Asked Questions ........................................................................... 3-7

3-5 Returning Merchandise for Service................................................................. 3-8

Chapter 4 BIOS

4-1 Introduction ...................................................................................................... 4-1

4-2 Main Setup ...................................................................................................... 4-2

4-3 Advanced Setup Congurations...................................................................... 4-4

4-4 Event Logs .................................................................................................... 4-26

4-5 IPMI ............................................................................................................... 4-28

4-6 Boot ............................................................................................................... 4-30

4-7 Security ......................................................................................................... 4-31

4-8 Save & Exit ................................................................................................... 4-32

Appendix A BIOS Error Beep Codes

A-1 BIOS Error Beep Codes .................................................................................A-1

Appendix B Software Installation Instructions

B-1 Installing Software Programs ..........................................................................B-1

B-2 Conguring SuperDoctor III ............................................................................B-2

X9DBL-i/3/iF/3F Motherboard User’s Manual

Chapter 1: Overview

1-1

Chapter 1

Overview

1-1 Overview

Checklist

Congratulations on purchasing your computer motherboard from an acknowledged

leader in the industry. Supermicro boards are designed with the utmost attention to

detail to provide you with the highest standards in quality and performance.

Please check that the following items have all been included with your motherboard.

If anything listed here is damaged or missing, contact your retailer.

The following items are included in the retail box.

• One (1) Supermicro Mainboard

• Eight (8) Serial ATA cables (CBL-0044Lx8) (X9DBL-3F/3 Only)

•Six (6) Serial ATA cables (CBL-0044Lx6) (X9DBL-iF/i Only)

• One (1) I/O Shield (MCP-260-00027-0N)

• One (1) Quick Reference Guide (MNL#1307-QRG)

Note: For your system to work properly, please follow the links below to

download all necessary drivers/utilities and the user's manual for your

motherboard.

SMCI product manuals: http://www.supermicro.com/support/manuals/

Product Drivers and utilities: ftp://ftp.supermicro.com/

If you have any questions, please contact our support team at support@supermicro.

com.

1-2

X9DBL-i/3/iF/3F Motherboard User’s Manual

Motherboard Image

Note: All graphics shown in this manual were based upon the latest PCB

revision available at the time of publishing of the manual. The motherboard

you've received may or may not look exactly the same as the graphics

shown in this manual.

Chapter 1: Overview

1-3

Motherboard Layout

Note : For the latest CPU/Memory updates, please refer to our website at

http://www.supermicro.com/products/motherboard/ for details.

JD1

JPW1

JIPMB1

LED3

T-SGPIO1

T-SGPIO2

JSTBY1

J9

JBT1

JPI2C1

JF1(FP Control)

TPM/Port80

JL1

JI2C1JI2C2

JOH1

LED1

JWP1

JBR1

JPME1

JVRM_I2C1

JVRM_I2C2

JPG1

JPB1

JPL1
JPL2

JCPUVRD_SMB

I-SATA1

I-SATA0

S-SATA/
SAS0

1

7

I-SATA2

I-SATA3

I-SATA4

I-SATA5

BT1

SP1

FAN4

FAN1

FAN2

FAN5

FANA

FAN3

JPW2

JPW3

SCU-

SGPIO1

USB2/3

USB4/5

KB/MOUSE

CPU1 SLOT2 PCI-E 3.0 X4(IN X8)

CPU1

P2-DIMM1F

P2-DIMM1E

P2-DIMM1D

P1-DIMM1B

P1-DIMM1A

P1-DIMM1C

LAN2

CPU2 SLOT3 PCI-E 3.0 X8

CPU2 SLOT5 PCI-E 3.0 X8

CPU2 SLOT4 PCI-E 3.0 X8

CPU1 SLOT6 PCI-E 3.0 X16

SLOT1 PCI 33MHZ

USB6

IPMI_LAN

VGA COM1

USB0/1

LAN1

COM2

CPU2

JWD1

BIOS

Battery

LAN CTRL

LAN CTRL

BMC CTRL

CPLD

Intel PCH

X9DBL-i/3 (F)

Rev. 1.01

LED2

JUIDB1

SCU-

SGPIO2

S-SATA/
SAS1
S-SATA/
SAS2
S-SATA/
SAS3

S-SATA/
SAS4

S-SATA/
SAS5

S-SATA/SAS6

S-SATA/
SAS7

1-4

X9DBL-i/3/iF/3F Motherboard User’s Manual

Notes:

•See Chapter 2 for detailed information on jumpers, I/O ports and JF1 front

panel connections.

•" " indicates the location of "Pin 1".

•Jumpers/LED Indicators/connectors/headers not indicated are for testing only.

Components not documented are reserved for internal testing only.

•Use only the correct type of onboard CMOS battery as specied by the

manufacturer. Do not install the onboard battery upside down to avoid possible

explosion.

X9DBL-i/3/iF/3F Quick Reference

JD1

JPW1

JIPMB1

LED3

T-SGPIO1

T-SGPIO2

JSTBY1

J9

JBT1

JPI2C1

JF1(FP Control)

TPM/Port80

JL1

JI2C1JI2C2

JOH1

LED1

JWP1

JBR1

JPME1

JVRM_I2C1

JVRM_I2C2

JPG1

JPB1

JPL1
JPL2

JCPUVRD_SMB

I-SATA1

I-SATA0

S-SATA/
SAS0

1

7

I-SATA2

I-SATA3

I-SATA4

I-SATA5

BT1

SP1

FAN4

FAN1

FAN2

FAN5

FANA

FAN3

JPW2

JPW3

SCU-

SGPIO1

USB2/3

USB4/5

KB/MOUSE

CPU1 SLOT2 PCI-E 3.0 X4(IN X8)

CPU1

P2-DIMM1F

P2-DIMM1E

P2-DIMM1D

P1-DIMM1B

P1-DIMM1A

P1-DIMM1C

LAN2

CPU2 SLOT3 PCI-E 3.0 X8

CPU2 SLOT5 PCI-E 3.0 X8

CPU2 SLOT4 PCI-E 3.0 X8

CPU1 SLOT6 PCI-E 3.0 X16

SLOT1 PCI 33MHZ

USB6

IPMI_LAN

VGA COM1

USB0/1

LAN1

COM2

CPU2

JWD1

BIOS

Battery

LAN CTRL

LAN CTRL

BMC CTRL

CPLD

Intel PCH

X9DBL-i/3 (F)

Rev. 1.01

LED2

JUIDB1

SCU-

SGPIO2

S-SATA/
SAS1
S-SATA/
SAS2
S-SATA/
SAS3

S-SATA/
SAS4

S-SATA/
SAS5

S-SATA/SAS6

S-SATA/
SAS7

Chapter 1: Overview

1-5

X9DBL-i/3/iF/3F Jumpers

Jumper

Description Default Setting

JBT1

Clear CMOS See Chapter 2

JI2C1/JI2C2 SMB to PCI-E Slots Pins Open (Normal)

JPB1 BMC Enable Pins 1-2 (Enabled)

JPG1 VGA Enable Pins 1-2 (Enabled)

JPL1/JPL2 LAN1/LAN2 Enable Pins 1-2 (Enabled)

JVRM_I2C1/JVRM_I2C2 I2C Bus to CPU1/CPU2

VRMs

Pins 1-2 (Enabled:
X9DBL-3F/iF),
Pins 2-3 (Enabled:
X9DBL-3/i),

JWD1 Watch Dog Pins 1-2 (Reset)

X9DBL-i/3/iF/3F Connectors

Connectors Description

Battery Onboard Battery (See Chpt. 4 for Used Battery Disposal)

COM1/COM2 Backplane COM Port1/Front Accessible COM2 Header

FAN1~5, FANA CPU/System Fan Headers

I-SATA 0~5 Intel PCH SATA Connectors 0~5

JD1 Power LED/Speaker (PWR LED Pins 1~3, Speaker: Pins 4~7)

JF1 Front Panel Control Header

JIPMB1 4-pin External BMC I2C Header (for an IPMI Card)

JL1 Chassis Intrusion

JOH1 Overheat/Fan Fail LED

JPI2C1 Power Supply SMBbus I2C Header

JPW1 ATX 24-Pin Power Connector (See Warning on Pg. 1-6.)

JPW2~JPW3 12V 8-Pin Power Connectors (See Warning on Pg. 1-6.)

JSTBY1 Standby Power Header

JTPM1 TPM (Trusted Platform Module)/Port 80

KB/Mouse Keyboard/Mouse

LAN1/2 G-bit Ethernet Ports 1/2

(IPMI) LAN IPMI_Dedicated LAN

S-SATA/SAS 0~3,
SAS 4~7

S-SATA/SAS Connections 0~3, SAS 4~7 (X9DBL-3F/3 Only)

S-SATA/SAS 0~3 S-SATA/SAS Connections 0~3 from Intel SCU (X9DBL-iF/i

Only)

SP1 Internal Buzzer/Speaker

1-6

X9DBL-i/3/iF/3F Motherboard User’s Manual

Warning!

To avoid damaging the power supply or the motherboard, please use a power supply

that contains a 24-pin, and two 8-pin power Power connectors. Be sure to connect

these power supply connectors to all power connector on the motherboard. Failure in

doing so will void the manufacturer warranty on your power supply and motherboard.

Slot1 PCI 33 MHz Slot

(CPU2) Slot3/4/5 PCI-Exp. 3.0 x8 Slots

(CPU 1) Slot2 PCI-Exp. 3.0 x4 in x8 Slot

(CPU 1) Slot6 PCI-Exp. 3.0 x4 in x16 Slot

SCU-SGPIO 1 Serial Link General Purpose I/O Connector 1 for SCU-SATA/

SAS 0~3 (from SCU)

SCU-SGPIO 2
(For X9DBL-3/3F)

Serial Link General Purpose I/O Connector 2 for SCU-SATA/
SAS 4~7 (from SCU)

T-SGPIO 1 Serial Link General Purpose I/O Connector 1 for I-SATA 0~5

T-SGPIO 2 Serial Link General Purpose I/O Connector 1 for I-SATA 4/5

TPM/Port 80 TPM (Trusted Platform Module)/Port 80 Connection (JTPM)

USB 0/1 Back Panel USB 0/1

USB 2/3, 4/5 Front Panel Accessible USB 2/3, 4/5 Connections

USB 6 Front Panel Type A USB 6 Port

UID Switch UID (Unit Identier) Switch

VGA Backpanel VGA Port 1/Front Panel VGA Port2

X9DBL-i/3/iF/3F LED Indicators

LED Description State Status

LED1 BMC Heartbeat LED Green: Blinking Normal

LED2 Standby PWR LED Green: On SB Power On

LED3 UID LED

Blue: On (Windows OS),
Blinking (Linux)

Unit Identied

Chapter 1: Overview

1-7

Motherboard Features

CPU

• Dual Intel

®

E5-2400 Series (Socket B2) processors (up

to 95W); each processor supports two full-width Intel

QuickPath Interconnect (QPI) links of up to 8.0 GT/s per

QPI link with data transfer rate of up to 16 GB/s band-

width per port

Memory

• Integrated memory controller supports:

• Six 240-pin DDR3 Registered/Load Reduced ECC or

Unbuffered ECC/Non-ECC 800/1066/1333/1600 MHz

memory modules with support of up to 192 GB in three-

channel memory bus

Note: For the latest CPU/memory updates, please

refer to our Website at http://www.supermicro.com/

products/motherboard.

DIMM sizes

• R_DIMM/LR_

DIMM

1GB, 2GB, 4GB, 8GB,16GB and

32GB @ 1.35V/1.5V

• Virtualization: VT-x, VT-d, and VT-c

Chipset

• Intel® C606/C602 PCH

Graphics

• Matrox G200eW Video Controller

Network

• Dual Intel 82574L Gigabit Ethernet Controllers for LAN1/

LAN2 ports.

I/O

SATA/SAS Connections

Devices

• SATA Ports Six (6) SATA ports total: Two (2)

SATA 3.0 ports & four (4) SATA

2.0 ports

• RAID RAID 0, 1, 5, 10

• SAS Connectors Eight (8) SAS Connectors SCU-

SATA/SAS 0~3, 4~7 for X9DBL-

3F/3,

Four (4) SAS Connections: SCU-

SATA/SAS 0~3 for X9DBL-iF/i

• RAID RAID 0, 1, 10

Super I/O

• Nuvoton W83527 SI/O

• Nuvoton WPCM450R Base-board Controller (BMC) sup-

ports IPMI_LAN 2.0 (for X9DBL-3F/iF only)

1-8

X9DBL-i/3/iF/3F Motherboard User’s Manual

IPMI 2.0 (For X9DBL-iF/3F)

• Nuvoton WPCM450R Base-board Controller (BMC)

supports IPMI_LAN 2.0

Serial (COM) Port

• Two (2) Fast UART 16550 connections: 9-pin RS-

232 port

Keyboard/Mouse

• Backplane USB Keyboard/Mouse

VGA

• Backplane VGA Port 1

Expansion Slots

• One (1) PCI-E 3.0 x16 Slot (Slot6)

• Three (3) PCI-E 3.0 x8 Slots (Slots3~5)

• One (1) PCI-E 3.0 x4 in x8 Slot (Slot2)

• One PCI 33 MHz (Slot1)

Peripheral
Devices

USB Devices

• Two (2) USB 2.0 ports on the rear I/O panel (USB 0/1)

• Two (2) Front Panel USB headers for 4 connections

(USB 2/3, USB 4/5)

• One Type A USB connectors for front-access (USB 6)

BIOS

• 64 Mb AMI BIOS

®

Flash EEPROM

• APM 1.2, DMI 2.3, PCI 2.3, ACPI 1.0/2.0, USB Key-

board, Plug & Play (PnP) and SMBIOS 2.3

Power

• ACPI/ACPM Power Management

Cong.

• Main switch override mechanism

• Keyboard Wake-up from Soft-Off

• Power-on mode for AC power recovery

PC Health

CPU Monitoring

Monitoring

• Onboard voltage monitors for 1.5V, 1.8V, +3.3V, 3.3V

Standby, +5V, +5V Standby and Battery Voltage.

• CPU Thermal Design Power (TDP): support up to

95W (See Note 1 next page)

• CPU 6-Phase switching voltage regulator

• CPU/System overheat LED and control

• CPU Thermal Trip support

• Thermal Monitor 2 (TM2) support

Chapter 1: Overview

1-9

• Intel® Intelligent Power Node Management (IPNM)

• Intel® Manageability Engine (ME)

Fan Control

• Fan status monitoring with rmware 4-pin (Pulse

Width Modulation) fan speed control

• Low noise fan speed control

LED Indicators

• System/CPU Overheat LED

• Suspend-state LED

• UID/Remote UID LED

System
Management

• PECI (Platform Environment Conguration Interface)

2.0 support

• System resource alert via SuperDoctor III

• Dual Cooling Zones

• Thermal Monitor 2 (TM2) support

• PECI (Platform-Environment Conguration Interface)

support

• SuperoDoctor® III, Watch Dog, NMI

• Chassis Intrusion Header and Detection

Dimensions

• 12.00" (L) x 10.00" (W) (304.80 mm x 254.00 mm)

Note 1: CPU Maximum Thermal Design Power (TDP) is subject to chassis

and heatsink cooling restrictions. For proper thermal management, please

check the chassis and heatsink specications for proper CPU TDP sizing.

Note 2: For IPMI Conguration Instructions, please refer to the Embedded

IPMI Conguration User's Guide available @ http://www.supermicro.com/

support/manuals/.

1-10

X9DBL-i/3/iF/3F Motherboard User’s Manual

System Block Diagram

Notes: 1. This is a general block diagram and may not exactly represent

the features on your motherboard. See the Motherboard Features pages

for the actual specications of each motherboard. 2. This block diagram

is intended for your reference only.

USB 2.0

PCH

SSB-D/A

PCI-E X16 Gen3

DMI

DMI

2 Rear
4 Front
1 Type-A

PCI-E X1

QPI

8G

4GB/s

3.0 Gb/S
for Ports 0/1

PCI-32MHz

PCI

LPC

SLOT 2

SLOT 6

SLOT 1

PCI-E X4 Gen3

PCI-E X1 Gen2

3.0 Gb/S for Ports 2~5
(SCU-SATA/SAS)

PCI-E
#1

PCI-E
#1

6.0 Gb/S

PEG0

PCI-E x4

CPU 2

DDR 3

P1

#3 #3 #1

CPU 1

DDR 3

P0

#1 #3 #1 DMI

#D-1

800/1066/1333/1600

DDR3

#E-1

#F-1

PCI-E X1 Gen2

#A-1

800/1066/1333/1600

DDR3

#B-1

#C-1

PCI-E X4

in X8 slot

PCI-E X16

PCI-33MHz

SLOT 5

PCI-E X16

SLOT 4

PCI-E X16

SLOT 3

PCI-E X16

82574L

GLAN 1

82574L

GLAN 2

RJ45

RJ45

BMC
VGA

VGA

IPMI LAN

BIOS

#0~#7

#0~#5

#0~#6

SAS

SATA

USB

SIO
W83527

COM1
External

COM2
Header

TPM
Header

PCI-E X8 Gen3

SCU-

SATA/SAS

SPI

PCI-E X8 Gen3

PCI-E X8 Gen3

Chapter 1: Overview

1-11

1-2 Processor and Chipset Overview

Built upon the functionality and the capabilities of Intel E5-2400 Series (Socket

B2) processor and C606/C602 chipset, the X9DBL-i/3/iF/3F motherboard provides

the performance and feature sets required for dual_processor-based high-end

system platforms.

With support of Intel QuickPath interconnect (QPI) Technology, the X9DBL-i/3/

iF/3F motherboard offers point-to-point serial interconnect interface with a transfer

speed of up to 8.0 GT/s, providing superb system performance.

The C606/C602 chipset provides extensive IO support, including the following

functions and capabilities:

•PCI-Express Rev. 2.0 support

•PCI-Express Gen. 3 uplink supported by some SKUs

•ACPI Power Management Logic Support Rev. 3.0b or Rev. 4.0

•USB host interface backplane and front access support

•Intel Rapid Storage Technology supported

•Intel Virtualization Technology for Directed I/O (Intel VT-d) supported

•Intel Trusted Execution Technology supported

•Serial Peripheral Interface (SPI) Supported

•Digital Media Interface (DMI) supported

•Advanced Host Controller Interface (AHCI) supported

1-12

X9DBL-i/3/iF/3F Motherboard User’s Manual

1-3 Special Features

Recovery from AC Power Loss

The Basic I/O System (BIOS) provides a power setting that determines how the

system will respond when AC power is lost and then restored to the system. You

can choose for the system to remain powered off (in which case you must press

the power switch to turn it back on), or for it to automatically return to the power-on

state. See the Advanced BIOS Setup section for this setting. The default setting

is Last State.

1-4 PC Health Monitoring

This section describes the features of PC health monitoring of the motherboard.

This motherboard has an onboard System_Hardware_Monitor chip that supports

PC health monitoring. An onboard voltage monitor will scan the following onboard

voltages continuously: 1.5V, 1.8V, +3.3V, 3.3V Standby, +5V, +5V Standby and

Battery Voltage. Once a voltage becomes unstable, a warning is given, or an error

message is sent to the screen. The user can adjust the voltage thresholds to dene

the sensitivity of the voltage monitor.

Fan Status Monitor with Firmware Control

The PC health monitor chip can check the RPM status of a cooling fan. The on-

board CPU and chassis fans are controlled by the rmware thermal management

under IPMI.

Environmental Temperature Control

A thermal control sensor monitors the CPU temperature in real time and will turn

on the thermal control fan whenever the CPU temperature exceeds a user-dened

threshold. The overheat circuitry runs independently from the CPU. Once it detects

that the CPU temperature is too high, it will automatically turn on the thermal fan

control to prevent the CPU from overheating. The onboard chassis thermal circuitry

can monitor the overall system temperature and alert the user when the chassis

temperature is too high.

Note: To avoid possible system overheating, please be sure to provide

adequate airow to your system.

System Resource Alert

This feature is available when used with SuperDoctor III in the Windows OS

Chapter 1: Overview

1-13

environment or used with SuperDoctor II in Linux. SuperDoctor is used to notify

the user of certain system events. For example, you can congure SuperDoctor to

provide you with warnings when system temperature, CPU temperature, voltages

and fan speeds go beyond a predened range.

1-5 ACPI Features

ACPI stands for Advanced Conguration and Power Interface. The ACPI specica-

tion denes a exible and abstract hardware interface that provides a standard

way to integrate power management features throughout a PC system, including

hardware, operating system and application software. This enables the system to

automatically turn on and off peripherals such as CD-ROMs, network cards, hard

disk drives and printers.

In addition to enabling operating_system-directed power management, ACPI also

provides a generic system event mechanism for Plug and Play, and an operating

system-independent interface for conguration control. ACPI leverages the Plug and

Play BIOS data structures, while providing a processor architecture-independent

implementation that is compatible with Windows 7, Windows Vista and Windows

2008 Operating Systems.

Slow Blinking LED for Suspend-State Indicator

When the CPU goes into a suspend state, the chassis power LED will start blinking

to indicate that the CPU is in suspend mode. When the user presses any key, the

CPU will "wake up" and the LED will automatically stop blinking and remain on.

1-6 Power Supply

As with all computer products, a stable power source is necessary for proper and

reliable operation. It is even more important for processors that have high CPU

clock rates.

The X9DBL-i/3/iF/3F motherboard accommodates 24-pin ATX power supplies.

Although most power supplies generally meet the specications required by the

CPU, some are inadequate. In addition, two 12V 8-pin power connections (JPW2/

JPW3) are also required to ensure adequate power supply to the system. Your

power supply must also supply 1.5A for the Ethernet ports.

Warning! To avoid damaging the power supply or the motherboard, please use a power

supply that contains a 24-pin and two 8-pin power connectors. Be sure to connect

these power supply connectors to all power connectors on the motherboard. Failure

to do so will void the manufacturer warranty on your power supply and motherboard.

1-14

X9DBL-i/3/iF/3F Motherboard User’s Manual

It is strongly recommended that you use a high quality power supply that meets ATX

power supply Specication 2.02 or above. It must also be SSI compliant. (For more

information, please refer to the website at http://www.ssiforum.org/). Additionally, in

areas where noisy power transmission is present, you may choose to install a line

lter to shield the computer from noise. It is recommended that you also install a

power surge protector to help avoid problems caused by power surges.

1-7 Super I/O

The Super I/O supports two high-speed, 16550 compatible serial communication

ports (UARTs). Each UART includes a 16-byte send/receive FIFO, a programmable

baud rate generator, complete modem control capability and a processor interrupt

system. Both UARTs provide legacy speed with baud rates of up to 115.2 Kbps

as well as an advanced speed with baud rates of 250 K, 500 K, or 1 Mb/s, which

support higher speed modems.

The Super I/O provides functions that comply with ACPI (Advanced Conguration

and Power Interface), which includes support of legacy and ACPI power manage-

ment through an SMI or SCI function pin. It also features auto power management

to reduce power consumption.

1-8 Advanced Power Management

The new advanced power management features supported by this motherboard

include IPNM and ME. Please note that you will need to do following to use these

two new features:

•Use a power supply that supports PMBus 1.1 or 1.2.

•Install the NMView software in your system. NMView is optional and can be

purchased from Supermicro.

Intel® Intelligent Power Node Manager (IPNM)

The Intel® Intelligent Power Node Manager (IPNM) provides your system with

real-time thermal control and power management for maximum energy efciency.

Although IPNM is supported by the BMC (Baseboard Management Controller),

your system must also have IPNM-compatible Manageability Engine (ME) rmware

installed in your system for IPNM support.

Note: Support for IPNM Specication Version 1.5 or Vision 2.0 depends

on the power supply used in the system.

Chapter 1: Overview

1-15

Manageability Engine (ME)

The Manageability Engine, which is an ARC controller embedded in the PCH,

provides Server Platform Services (SPS) to your system. The services provided by

SPS are different from those provided by the ME on client platforms.

1-9 Introduction to the IPMI Controller (For X9DBL-iF/3F
only)

The Nuvoton WPCM450R Controller, a Baseboard Management Controller (BMC),

supports 2D/VGA-compatible Graphic Cores with PCI interface, creating multi-media

virtualization via Keyboard/Video/Mouse Redirection (KVMR). The WPCM450R

Controller is ideal for remote system management.

The WPCM450R Controller interfaces with the host system via PCI connections

to communicate with the graphics cores. It supports USB 2.0 and 1.1 for remote

keyboard/mouse/virtual media emulation. It also provides LPC interface support to

control Super IO functions. The WPCM450R Controller is connected to the network

via an external Ethernet PHY module or shared NCSI connections.

The WPCM450R communicates with onboard components via six SMBus inter-

faces, PECI (Platform Environment Control Interface) buses, and General Purpose

I/O ports.

WPCM450R DDR2 Memory Interface

The WPCM450R supports a 16-bit DDR2 memory module with a speed of up to 220

MHz. For best signal integrity, the WPCM450R provides point-to-point connection.

WPCM450R PCI System Interface

The WPCM450R provides 32-bit, 33 MHz 3.3V PCI interface, which is compliant

with the PCI Local Bus Specication Rev. 2.3. The PCI system interface connects

to the onboard PCI Bridge used by the graphics controller.

Other Features Supported by the WPCM BMC Controller

The WPCM450R supports the following features:

•IPMI 2.0

•Serial over LAN

•KVM over LAN

•LAN Alerting-SNMP Trap

1-16

X9DBL-i/3/iF/3F Motherboard User’s Manual

•Event Log

•X-Bus parallel interface for I/O expansion

•Multiple ADC inputs, Analog and Digital Video outputs

•SPI Flash Host BIOS and rmware bootstrap program supported

•Reduced Media Independent Interface (RMII)

•OS (Operating System) Independency

•Provides remote Hardware Health Monitoring via IPMI. Key features

•Provides Network Management Security via remote access/console redirec-

tion.

•Supports the following Management tools: IPMIView, CLI (Command Line

Interface)

•RMCP+ protocol supported

Note: For more information on IPMI conguration, please refer to the

IPMI User's Guide posted on our website at http://www.supermicro.com/

support/manuals/.

Chapter 2: Installation

2-1

Chapter 2

Installation

2-1 Standardized Warning Statements

The following statements are industry-standard warnings, provided to warn the user

of situations which have the potential for bodily injury. Should you have questions or

experience difculty, contact Supermicro's Technical Support department for assis-

tance. Only certied technicians should attempt to install or congure components.

Read this section in its entirety before installing or conguring components in the

Supermicro chassis.

Battery Handling

Warnung

Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die

Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp.

Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.

Warning!

There is a danger of explosion if the battery is replaced incorrectly. Replace the

battery only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer's instructions

電池の取り扱い

電池交換が正しく行われなかった場合、破裂の危険性があります。 交換する電池はメー
カーが推奨する型、または同等のものを使用下さい。 使用済電池は製造元の指示に従

って処分して下さい。

警告
电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更
换原有电池。请按制造商的说明处理废旧电池。

警告
電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有
電池。請按照製造商的說明指示處理廢棄舊電池。

2-2

X9DBL-i/3/iF/3F Motherboard User’s Manual

Attention

Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer

que par une pile de type semblable ou équivalent, recommandée par le fabricant.

Jeter les piles usagées conformément aux instructions du fabricant.

¡Advertencia!

Existe peligro de explosión si la batería se reemplaza de manera incorrecta. Re-

emplazar la batería exclusivamente con el mismo tipo o el equivalente recomen-

dado por el fabricante. Desechar las baterías gastadas según las instrucciones

del fabricante.

!הרהזא

תנכס תמייקץוציפ .הניקת אל ךרדב הפלחוהו הדימב הללוסה לש ףילחהל שי

גוסב הללוסה תא מ םאותה תרבחלמומ ןרציתצ.

תוללוסה קוליס תושמושמה עצבל שי .ןרציה תוארוה יפל









경고!

배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와 동일
하거나 제조사에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다. 제조사
의 안내에 따라 사용된 배터리를 처리하여 주십시오.

Waarschuwing

Er is ontplofngsgevaar indien de batterij verkeerd vervangen wordt. Vervang de

batterij slechts met hetzelfde of een equivalent type die door de fabrikant aan-

bevolen wordt. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften

afgevoerd te worden.

Chapter 2: Installation

2-3

Product Disposal

Warning!

Ultimate disposal of this product should be handled according to all national laws

and regulations.

製品の廃棄

この製品を廃棄処分する場合、国の関係する全ての法律・条例に従い処理する必要が

ありま す。

警告
本产品的废弃处理应根据所有国家的法律和规章进行。

警告
本產品的廢棄處理應根據所有國家的法律和規章進行。

Warnung

Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen

des Landes erfolgen.

¡Advertencia!

Al deshacerse por completo de este producto debe seguir todas las leyes y regla-

mentos nacionales.

Attention

La mise au rebut ou le recyclage de ce produit sont généralement soumis à des

lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de

l'organisme compétent.

רצומה קוליס

!הרהזא

ו תויחנהל םאתהב תויהל בייח הז רצומ לש יפוס קוליס.הנידמה יקוח

2-4

X9DBL-i/3/iF/3F Motherboard User’s Manual

2-2 Static-Sensitive Devices

Electrostatic Discharge (ESD) can damage electronic com ponents. To avoid dam-

aging your system board, it is important to handle it very carefully. The following

measures are generally sufcient to protect your equipment from ESD.

Precautions

•Use a grounded wrist strap designed to prevent static discharge.

•Touch a grounded metal object before removing the board from the antistatic

bag.

•Handle the board by its edges only; do not touch its components, peripheral

chips, memory modules or gold contacts.

•When handling chips or modules, avoid touching their pins.

•Put the motherboard and peripherals back into their antistatic bags when not

in use.

•For grounding purposes, make sure that your system chassis provides excellent

conductivity between the power supply, the case, the mounting fasteners and

the motherboard.

Unpacking

The motherboard is shipped in antistatic packaging to avoid static damage. When

unpacking the board, make sure that the person handling it is static-protected.

Waarschuwing

De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming

met alle nationale wetten en reglementen.

 

경고!

이 제품은 해당 국가의 관련 법규 및 규정에 따라 폐기되어야 합니다.

Chapter 2: Installation

2-5

2-3 Processor and Heatsink Installation

When handling the processor package, avoid placing direct pressure on the label

area of the fan.

Notes:

1. Always connect the power cord last, and always remove it before adding,

removing, or changing any components. Make sure that you install the pro-

cessor into the CPU socket before you install the CPU heatsink.

2. Make sure that the processor wattage (TDP) does not exceed the maximum

rating for the motherboard. Also, check that it is within the rating limits of the

heatsink and chassis to ensure proper cooling and operation. Refer to the

chassis manual for more information.

3. Make sure to install the motherboard into the chassis before you install the

CPU heatsink and heatsink fans.

4. When purchasing a motherboard without a processor pre-installed, make sure

that the CPU socket plastic cap is in place, and none of the CPU socket pins

are bent; otherwise, contact the retailer immediately.

5. Refer to the Motherboard Features section of the manual and our website

for more information on CPU support and updates.

Installing an LGA 1356 Processor

1. Press the socket clip to release the load plate that covers the CPU socket

from its locked position.

2. Gently lift the socket clip to open the load plate.

2-6

X9DBL-i/3/iF/3F Motherboard User’s Manual

Warning: Please save the plastic cap. The motherboard must be shipped with the

plastic cap properly installed to protect CPU socket pins. Shipping without the plastic

cap properly installed will cause damage to the socket pins.

3. Hold the plastic cap at its north and south center edges to remove it from the

CPU socket.

4. After removing the plastic cap, hold the CPU at the north and south center

edges with your thumb and index nger.

5. Align the CPU key, a semi-circle cutout, against the socket key, which is the

notch below the gold color dot on the side of the socket.

6. Align Pin 1 on the CPU with Pin 1 on the CPU socket.

7. Once both CPU and the socket are aligned, carefully lower the CPU straight

down into the socket. (To avoid damaging the CPU or the socket, do not rub

the CPU against the surface of the socket or its pins.)

8. With the CPU inside the socket, inspect the four corners of the CPU to make

sure that the CPU is properly installed.

9. Once the CPU is securely seated on the socket, lower the CPU load plate to

the socket.

10. Use your thumb to gently push the socket clip down to the clip lock.