Supero X8DTH-6, X8DTH-6F, X8DTH-i, X8DTH-iF User Manual

X8DTH-6

X8DTH-6F

X8DTH-i
X8DTH-iF

USER’S MANUAL

Revision 1.0c

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our website at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software, if any,
and documentation may not, in whole or in part, be copied, photocopied, reproduced, translated or
reduced to any medium or machine without prior written consent.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTW ARE, OR DA TA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your
own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”

WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.

Manual Revision 1.0c
Release Date: Feb. 16, 2010

Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.

Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.

Copyright © 2010 by Super Micro Computer, Inc.
All rights reserved.

Printed in the United States of America

Preface

About this Manual

This manual is written for system integrators, PC technicians and knowledgeable PC
users. It provides information for the installation and use of the
X8DTH-6F/X8DTH-i/X8DTH-iF motherboard.

About this Motherboard

The X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF supports the Intel® 5500
Series Processor, the fi rst dual-processor platform that supports the Intel QuickPath
Interconnect (QPI) Technology, providing the next generation point-to-point system
interface to replace the current Front Side Bus. With the dual Intel 5520 chips built
in, the X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF offers substantial enhancement in
system performance with increased bandwidth and unprecedented scalability op­timized for High Performance Computing (HPC)/Clustering systems and intensive
applications. Please refer to our website (http://www.supermicro.com/products/)
for updates on supported processors. This product is intended to be installed and
serviced by professional technicians.

X8DTH-6/

Preface

Manual Organization

Chapter 1 describes the features, specifi cations and performance of the mother-

board and provides detailed information about the chipset.
Chapter 2 provides hardware installation instructions. Read this chapter when in-

stalling the processor, memory modules and other hardware components into the
system. If you encounter any problems, see Chapter 3, which describes trouble­shooting procedures for video, memory and system setup stored in the CMOS.

Chapter 4 includes an introduction to the BIOS and provides detailed information
on running the CMOS Setup utility.

Appendix A lists BIOS POST Error Codes. Appendix B provides Software Instal­lation Instructions.

Conventions Used in the Manual

Special attention should be given to the following symbols for proper installation and
to prevent damage done to the components or injury to yourself:

Danger/Caution: Instructions to be strictly followed to prevent catastrophic
system failure or to avoid bodily injury.

iii

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

Warning: Important information given to ensure proper system installation
or to prevent damage to the components.

Note: Additional Information given to differentiate various models or to
ensure correct system setup.

iv

Contacting Supermicro

Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.
San Jose, CA 95131 U.S.A.

Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)

[e-mail] (Technical Support)

Website: www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands

Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)

[e-mail] (Technical Support)
[e-mail] (Customer Support)

Asia-Pacifi c

Address: Super Micro Computer, Inc.

4F, No. 232-1, Liancheng Rd.
Chung-Ho 235, Taipei County
Taiwan, R.O.C.

Tel: [phone]
Fax: [phone]
Website: www.supermicro.com.tw
Technical Support:
Email: [e-mail]
Tel: [phone], ext.132 or 139

v

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

Table of Contents

Preface
Chapter 1 Introduction

1-1 Overview .........................................................................................................1-1

1-2 Chipset Overview ............................................................................................1-9

1-3 Special Features ...........................................................................................1-10

1-4 PC Health Monitoring .................................................................................... 1-10

1-5 ACPI Features ................................................................................................1-11

1-6 Power Supply .................................................................................................1-11

1-7 Super I/O ....................................................................................................... 1-12

1-8 Overview of the Winbond WPCM450 Controller (For X8DTH-6F/iF Only) ...1-12

Chapter 2 Installation

2-1 Static-Sensitive Devices ..................................................................................2-1

Precautions .....................................................................................................2-1

Unpacking .......................................................................................................2-1

2-2 Motherboard Installation ..................................................................................2-2

Tools Needed .................................................................................................. 2-2

Installation Instructions ....................................................................................2-2

2-3 Processor and Heatsink Installation................................................................2-3

Installing a CPU Heatsink ...............................................................................2-5

2-4 Memory Installation ........................................................................................ 2-7

2-5 Control Panel Connectors/IO Ports...............................................................2-10

1. Back Panel Connectors/IO Ports .............................................................. 2-10

ATX PS/2 Keyboard and PS/2 Mouse Ports .............................................2-11

Serial Ports ............................................................................................... 2-12

Video Connector .......................................................................................2-12

Universal Serial Bus (USB) ...................................................................... 2-13

Ethernet Ports .......................................................................................... 2-14

2. Front Control Panel ...................................................................................2-15

3. Front Control Panel Pin Defi nitions .......................................................... 2-16

NMI Button ............................................................................................... 2-16

Power LED ..............................................................................................2-16

HDD LED .................................................................................................. 2-17

NIC1/NIC2 LED Indicators ....................................................................... 2-17

Overheat (OH)/Fan Fail LED....................................................................2-18

Power Fail LED ........................................................................................ 2-18

Reset Button ........................................................................................... 2-19

vi

Table of Contents

Power Button ........................................................................................... 2-19

2-6 Connecting Cables ........................................................................................ 2-20

Power Connectors ...................................................................................2-20

Fan Headers ............................................................................................. 2-21

Chassis Intrusion .....................................................................................2-21

Power LED/Speaker ................................................................................. 2-22

Wake-On-LAN ..........................................................................................2-22

Overheat LED/Fan Fail (JOH1) ................................................................2-23

SATA-SGPIO 0/1 Headers ....................................................................... 2-23

System Management Bus ........................................................................ 2-24

Power SMB (I

2

C) Connector .................................................................... 2-24

FP IPMI Heartbeat LED Header (X8DTH-6F/iF Only) ............................. 2-25

DOM Power Connector ............................................................................ 2-26

2-7 Jumper Settings ............................................................................................2-27

Explanation of Jumpers ................................................................................ 2-27

GLAN Enable/Disable ..............................................................................2-27

CMOS Clear ............................................................................................. 2-28

Watch Dog Enable/Disable ...................................................................... 2-28

2

I

C Bus to PCI-Exp. Slots ........................................................................ 2-29

VGA Enable .............................................................................................. 2-29

SAS Enable (X8DTH-6/6F Only) ..............................................................2-30

2-8 Onboard LED Indicators ............................................................................... 2-31

GLAN LEDs .............................................................................................. 2-31

IPMI Dedicated LAN LEDs (X8DTH-iF/6F) .............................................. 2-31

BMC Activity LED (X8DTH-iF/6F) ............................................................ 2-32

SAS Activity LED (X8DTH-6/6F) .............................................................. 2-32

SAS Heartbeat LED (X8DTH-6/6F) .......................................................... 2-33

SAS Error LED (X8DTH-6/6F) ................................................................. 2-33

Onboard Power LED ............................................................................... 2-34

2-9 SATA and SAS Connections ......................................................................... 2-35

SATA/SAS Connections (SAS: X8DTH-6/6F) .......................................... 2-35

Chapter 3 Troubleshooting

3-1 Troubleshooting Procedures ........................................................................... 3-1

Before Power On ............................................................................................ 3-1

No Power ........................................................................................................ 3-1

No Video ......................................................................................................... 3-2

Losing the System’s Setup Confi guration ....................................................... 3-2

Memory Errors ...............................................................................................3-2

vii

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

3-2 Technical Support Procedures ........................................................................3-3

3-3 Frequently Asked Questions ...........................................................................3-3

3-4 Returning Merchandise for Service.................................................................3-4

Chapter 4 BIOS

4-1 Introduction ...................................................................................................... 4-1

Starting BIOS Setup Utility ..............................................................................4-1

How To Change the Confi guration Data ......................................................... 4-1

Starting the Setup Utility ................................................................................. 4-2

4-2 Main Setup ......................................................................................................4-2

4-3 Advanced Setup Confi gurations...................................................................... 4-4

4-4 Security Settings ........................................................................................... 4-24

4-5 Boot Confi guration ........................................................................................4-25

Appendix A BIOS Error Beep Codes
Appendix B Software Installation Instructions

B-1 Installing Software Programs ..........................................................................B-1

B-2 Confi guring Supero Doctor III .........................................................................B-2

viii

Chapter 1: Introduction

Chapter 1

Introduction

1-1 Overview

Checklist

Congratulations on purchasing your computer motherboard from an acknowledged
leader in the industry. Supermicro boards are designed with the utmost attention
to detail to provide the highest standards in quality and performance. Check that
the following items have all been included with your motherboard. If anything listed
here is damaged or missing, contact your retailer.

The following items are included in the retail box.

One (1) Supermicro Mainboard

•

One (1) COM port cable (CBL-010L)•

One (1) USB 2.0 cable (CBL-0083L)•

Six (6) Serial ATA cables (CBL-0044L) (X8DTH-i/iF)•

Four (4) Serial ATA cables (CBL-0044L) (X8DTH-6/6F)•

Two (2) iPass to SATA cables (CBL-0097L-02) (X8DTH-6/6F)•

One I/O backpanel shield (MCP-260-00027-0N)•

One (1) Supermicro CD containing drivers and utilities•

One (1) User's/BIOS Manual (MNL#1083)•

1-1

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF Image

Note: The drawings and pictures shown in this manual were based on the

latest PCB Revision available at the time of publishing of the manual. The
motherboard you’ve received may or may not look exactly the same as
the graphics shown in the manual.

1-2

Chapter 1: Introduction

COM1

VGA

USB0/1

LAN1

LAN2

DP5

JPL1

FAN5

KB/MS

PHY

LAN CTRL

BMC

TPM

IPMI_LAN

FAN8

FAN6

JPG1

1

JI2C2

JPB

1

P2-DIMM3A

P2-DIMM3B

P2-DIMM2A

P2-DIMM2B

P2-DIMM1A

P2-DIMM1B

Slot7 PCI-E 2.0 X8

Slot6 PCI-E 2.0 X8

Slot5 PCI-E 2.0 X8

JI2C1

Slot4 PCI-E 2.0 X8

Slot3 PCI-E 2.0 X8

Slot2 PCI-E 2.0 X8

Slot1 PCI-E 2.0 X8

COM2

JHB1

1

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF Layout

Wake-On-LAN

JWOL1

CPU2

USB6/7

USB4/5

(South Bridge)

USB3

(IOH36D-2)

Intel

ICH10R

SATA-SGPIO1

SATA-SGPIO0

JPI2C

Intel

5520

JBT1

SPI BIOS

I-SATA5

I-SATA3

I-SATA4

I-SATA2

P1-DIMM1B

P1-DIMM1A

P1-DIMM2B

P1-DIMM2A

P1-DIMM3B

P1-DIMM3A

Intel

(IOH36D-1)

LED5

SAS Activity

JWF1

I-SATA1

JPW1

CPU1

5520

DP6

DP7

X8DTH

Rev. 2.0

JPS1

I-SATA0

LSI
SAS2008

RAID Key

JPW2

JPW3

SAS

FLASH

PWR_LED

Battery

SAS0~3

SAS4~7

FAN4

FAN1

FAN7

JF1

DP4

JWD

FAN2

SMBus1

JOH1

JD1

FAN3

Buzzer

JL1

Differences between X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF

SATA2 (ICH10R) Yes Yes Yes Yes

LSI SAS2.0 2008 Controller Yes Yes No No

IPMI 2.0 w/KVM No Yes No Yes

Notes

IPMI 2.0, Winbond WPCM450 Controller, the PHY chip and Dedicated LAN port

•

w/KVM support are available on the X8DTH-6F/iF only. For more information,
refer to the user guide posted on our website @ http://www.supermicro.com/
support/manuals/,

SAS2.0, LSI SAS2.0 2008 Controller, SAS Ports 0~7 are available on the

•

X8DTH-6/6F only. For more information on LSI RAID Confi guration, refer to
the LSI user guide posted on our website @ http://www.supermicro.com/sup­port/manuals/.

X8DTH-6 X8DTH-6F X8DTH-i X8DTH-iF

1-3

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

Quick Reference

COM1

VGA

USB0/1

LAN1

LAN2

DP5

JPL1

FAN5

KB/MS

PHY

LAN CTRL

BMC

TPM

FAN8

FAN6

IPMI_LAN

JPG1

JI2C2

1

JI2C1

JHB1

JPB

1

P2-DIMM3A

P2-DIMM3B

P2-DIMM2A

P2-DIMM2B

P2-DIMM1A

P2-DIMM1B

Slot7 PCI-E 2.0 X8

Slot6 PCI-E 2.0 X8

Slot5 PCI-E 2.0 X8

Slot4 PCI-E 2.0 X8

Slot3 PCI-E 2.0 X8

Slot2 PCI-E 2.0 X8

Slot1 PCI-E 2.0 X8

COM2

1

Wake-On-LAN

JWOL1

CPU2

USB6/7

USB4/5

(South Bridge)

USB3

(IOH36D-2)

Intel

ICH10R

SATA-SGPIO1

SATA-SGPIO0

JPI2C

Intel

5520

JBT1

SPI BIOS

I-SATA5

I-SATA3

I-SATA4

I-SATA2

P1-DIMM1B

P1-DIMM1A

P1-DIMM2B

P1-DIMM2A

P1-DIMM3B

P1-DIMM3A

Intel

(IOH36D-1)

LED5

SAS Activity

JWF1

I-SATA1

CPU1

5520

JPW1

DP6

DP7

JPS1

I-SATA0

X8DTH

Rev. 2.0

LSI
SAS2008

RAID Key

JPW2

JPW3

SAS

FLASH

PWR_LED

Battery

SAS0~3

SAS4~7

FAN4

FAN1

FAN7

JF1

DP4

JWD

FAN2

SMBus1

JOH1

JD1

FAN3

Buzzer

JL1

Notes

Jumpers not indicated are for test purposes only. 1.
" " indicates the location of Pin 1.2.
When DP4 is on, the onboard power connection is on. Make sure to unplug 3.

the power cables before removing or installing components.

Warning! 1. To prevent damage to the power supply or motherboard,
please use a power supply that contains a 24-pin and two 8-pin power
connectors. Be sure to connect these connectors to the 24-pin (JPW1)
and the two 8-pin (JPW2,JPW3) power connectors on the motherboard.
Failure in doing so will void the manufacturer warranty on your power
supply and motherboard.

2. To avoid system overheating, be sure to provide adequate air fl ow to
the system.

1-4

Chapter 1: Introduction

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF Quick Reference

Jumper Description Default Setting

JBT1 CMOS Clear Open (Normal)

2

C1/JI2C2 SMB to PCI/PCI-E Slots Closed/Closed (Enabled)

JI

JPG1 VGA Enable Pins 1-2 (Enabled)

JPL1 LAN1/2 Enable Pins 1-2 (Enabled)

JPS1 SAS2.0 Enable Pins 1-2 (Enabled) (X8DTH-6/-6F only)

JWD Watch Dog Pins 1-2 (Reset)

Connector Description

Buzzer Onboard Buzzer/Internal Speaker

(SPI) BIOS Onboard BIOS

COM1/COM2 Serial Ports 1/2

FAN 1-8 System/CPU Fan Headers (Fans 7~8: CPU Fans)

JD1 PWR LED/Speaker Header (Pins 1~3: PWR LED, Pins 4~7:

Speaker)
JF1 Front Panel Connector
JHB1 Front Panel IPMI Heartbeat LED Connection Header
JL1 Chassis Intrusion Header
JOH1 Overheat LED Header

2

C Power Supply SMBbus I2C Header

JPI
JPW1, JPW2/JPW3 24-pin ATX PWR, 8-pin Secondary PWR (See the Warning

on Page 1-4)
JWF1 SATA DOM (Disk-On-Module) Power Header
JWOL1 Wake-On-LAN Header
KB/MS PS2 Keyboard/Mouse
LAN1/2, Dedicated LAN G-LAN (RJ45) Ports (Dedicated LAN: X8DTH-6F/iF)
I-SATA0 ~ I-SATA5 (Intel South Bridge) SATA Ports
SAS Ports 0~3, 4~7 SAS Ports 0~3, 4~7 (X8DTH-6/6F only)
SMBUS1 System Management Bus Header
SATA-SGPIO-0/-1 Serial General Purpose I/O Headers for SATA
TPM Header Trusted Platform Module Header
USB 0/1, 3, 4/5, 6/7 Universal Serial Bus (USB) Ports
VGA VGA Con nec tor

LED Description

DP4 O nboa rd St andby Pow er LED In dic ator ( Power LE D)
DP5 B MC Ac tiv it y LED Ind ic ator
DP6 SAS Heartbeat LED Indicator: green (X8DTH-6/ X8DTH-6F only)
DP7 SAS Error LED Indicator: red (X8DTH-6/ X8DTH-6F only)
LED5 SAS Act ivi ty LE D Indi cat or (X8DTH-6/ X8DTH-6F only)

1-5

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

Motherboard Features

CPU

Two Intel•
full-width Intel QuickPath Interconnect (QPI) @6.4 GT/s with a total of up to 51.2
GB/s Data Transfer Rate (6.4 GT/s per direction)

®

5500 Series (LGA 1366) processors, each processor supporting two

Memory

12 240-pin DIMM sockets support up to 96 GB of Registered ECC or up to 24 •
GB of Unbuffered ECC/Non-ECC DDR3 1333/1066/800 MHz Memory (See
Section 2-4 in Chapter 2 for DIMM Slot Population.)

Chipset

Intel 5520 chipset, including: two IOH-36D hubs•
One ICH10R (South Bridge).•

Expansion Slots

Seven PCI-E 2.0 x8 slots (all in x16 slots: Slot 1~Slot 7)•

BIOS

32 Mb AMI SPI Flash ROM•
PCI 2.2, ACPI 1.0/2.0/3.0, Plug and Play (PnP), DMI 2.3, USB Keyboard sup-•

port, and SMBIOS 2.3

PC Health Monitoring

Onboard voltage monitors for CPU1 Vcore, CPU2 Vcore, CPU1 Vtt, CPU2 •
Vtt, CPU1 DIMM, CPU2 DIMM, 1.1V, 1.5V, 1.8V, 3.3V, 12V, 5V, 3.3 Vsb, and
VBAT

Fan status monitor with fi rmware control

•

CPU/chass is temper ature moni tors•
Platfo rm Enviro nment Co ntrol Inte rf ace (PECI) read y•
Ther mal Mo nitor 2 ( TM2) supp or t•
CPU fan auto - of f in sle ep mode•
CPU slow- dow n on tempe rature over heat•
Pulse Wi dth Mo dulati on (PW M) Fan Contr ol •
CPU ther mal tr ip supp or t for pro ces sor pr otecti on, power L ED•
Power-up mod e cont rol for r ecover y fr om AC power l oss•
Auto- switc hing vol tage r egulato r for CPU c ore s•
System over heat /Fan Fail LED I ndic ator and c ontr ol•
Chassis i ntrus ion detec tion•
System re sourc e aler t vi a Super o Doc tor III•

1-6

Chapter 1: Introduction

ACPI Features

Slow blinking LED for suspend state indicator•
Main switch override mechanism•
ACPI Pow er Ma nag eme nt•

Onboard I/O

Intel ICH10R supports six SATA2 ports (with RAID0, RAID1, RAID10, RAID5 •
supported in the Windows OS Environment and RAID0, RAID1, RAID10 sup­ported in the Linux OS.) (Note 1)

Intel 82576 Gi gabit Eth ernet c ontr oller su ppor ts du al Gig a-b it L AN po rt s

•

One VGA Por t supp or ted by the W inbon d WPCM 450 C ontro ller•
One CO M por t•
PS/2 mo use and PS /2 keyboa rd por ts•
Up to seven US B 2.0 (Univers al Serial Bus) (2 Back panel USB Por ts and 5 •

Front Panel Ac ces sible U SB co nnec tions)
Super I/ O: Winbo nd W83 527HG

•

LSI SAS2 2008 Controller supports eight SAS ports (X8DTH-6/X8DTH-6F only) •
(Note 2)
IPMI 2.0 w ith fu ll K VM supp or t (X8DT H- 6 F/iF only) (Note 3)

•

Other

Console redirection•
Onboa rd Fan Spee d Contr ol by Ther mal Ma nagem ent via BI OS•

CD/Diskette Utilities

BIOS fl ash upgrade utility and device drivers•

Dimensions

Ext . ATX 12.00" (L) x 13.00 " (W ) (304. 80 mm x 3 30. 20 mm)•

Note 1: For more information on SATA HostRAID confi guration, please
refer to the Intel SATA HostRAID User's Guide posted on our website @
http://www.supermicro.com/support/manuals/.

Note 2: For more information on IPMI confi guration, please refer to the
Embedded IPMI User's Guide posted on our website @ http://www.super­micro.com/support/manuals/.

1-7

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

#6

#5

#4

PCI-E X8 in X16 Slot

PCI-E X8 in X16 Slot

PCI-E X8 in X16 Slot

#1-5

#1-4

#1-3

#1-2

#1-1

DDR3

800/1066/1333

PCI-E X8

#7

PCI-E X8

PCI-E X8

PCI-E X8

PCI-E X8 in X16 Slot

#1-6

Ports 1&2

Ports 3&4

Ports 5&6

Ports 7&8

Ports 9&10

BIOS

PROCESSOR#2

(5500 Series)

QPI

Intel 5520

IOH2-36D

SPI

QPI

1

QPI

Intel

ICH10R

PROCESSOR#1

(5500 Series)

00

0

Intel 5520

IOH1-36D

U3H1

ESI

ESI X4

ESI

QPI

#0-3

#0-2

#0-1

DDR3

Ports 3&4

Ports 5&6

Ports 7&8

Ports 9&10

Ports 1&2

SATA2

USB2.0

PCI-E X8

PCI-E X8

PCI-E X8

PCI-E X8

PCI-E X4

#5

#4

#3

#2

#1

#0

SATA

USB

2 REAR+4 FRONT+ 1 TYPE A

#0-6

#0-5

#0-4

800/1066/1333

#1

LSI SAS2008

6 FRONT

#3

#2

PCI-E X8 in X16 Slot

PCI-E X8 in X16 Slot

PCI-E X8 in X16 Slot

6Gb/s

Optional

Intel 82576

LAN

0, 1, 2, 3

4, 5, 6, 7

LAN2

LAN1

RMII_IPMI

VGA

LPC BUS

COM1

External

SIO

W83527HG

U25

MS

KB

LAN3

IPMI_LAN

RTL8201N

PCI 33MHz

RMII
IPMI

USB

WPCM450

BMC

DDR II

Block Diagram of the Intel 5520 Platform

Note: This is a general block diagram. Please see the previous Mother-

board Features pages for details on the features of each motherboard.

1-8

Chapter 1: Introduction

1-2 Chipset Overview

Built upo n the fun ction ality a nd the ca pabilit y of the Inte l 550 0 Seri es Proc esso r
and the 5 520 c hips et, th e X8DTH -6/X8DT H - 6 F/X8 DTH -i / X8 DTH -i F mot her boa rd
provides the performance and feature set required for dual-processor-based
high- end systems opt imized for High Per formanc e Computing ( HPC)/Clusterin g
severs. T he Intel 5520 chip set consists of d ual 5520 IO hubs, a nd an ICH10R
(South Br idg e). With the Inte l Qui ck Path Inte rco nne ct (QPI) c ontr olle r buil t in, th e
Intel 55 00 S eri es Pro ces sor is t he fi rst dual-pr oc essi ng plat for m to of fer t he nex t
generation point-to-point system interconnect interface to replace the current
Front Side Bus Technology, substantially enhancing system performance and
scalability.

The 552 0 IO Hub co nnects to e ach proc essor t hrough an i ndepend ent QPI link.
Each link consists of 20 pairs of unidirectional differential lanes for transmission
and receiving in addition to a differential for warded clock. A full-width QPI link
pair provides 84 signals.

The Intel 5520 supp o rts up t o 36 PCI E x p r e ss Gen2 la n es, peer-to-p e e r r e a d a n d
write transactions. The ICH10R provides up to seven PCI-Express ports, six SATA
por ts and s even USB c onne cti ons.

In addition, the Intel 5520 chipset also offers a wide range of R AS (Reliabilit y,
Availability and Servi c ea bi li t y) featur e s. T he se f eat ur es i nc lu de m e mo ry interfac e
ECC, x4/x8 Single Device Data Correction (SDDC), Cyclic Redundancy Check
(CRC), parity pr otec tio n, out- o f- band re gist er ac ces s via S M Bus, me mory mir ro r­ing, and H ot-pl ug suppo rt o n the PCI - Ex press I nter face.

Main Features of the 5500 Series Processor and the 5520
Chipset

Four processor cores in each processor with 8MB shared cache among cores•

Two full-width Intel QPI links, up to 6.4 GT/s of data transfer rate in each direc-•
tion

Virtualization Technology, Integrated Management Engine supported

•

Point-to-point cache coherent interconnect, Fast/narrow unidirectional links, and •
Concurrent bi-directional traffi c

Error detection via CRC and Error correction via Link level retry

•

1-9

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

1-3 Special Features

Recovery from AC Power Loss

BIOS provides a setting for you to determine how the system will respond when
AC power is lost and then restored to the system. You can choose for the system
to remain powered off (in which case you must hit the power switch to turn it back
on) or for it to automatically return to a power- on state. See the Advanced BIOS
Setup section to change this setting. The default setting is Last State.

1-4 PC Health Monitoring

This section describes the PC health monitoring features of the X8DTH-6/X8DTH­6F/X8DTH-i/X8DTH-iF. All have an onboard System Hardware Monitor chip that
supports PC health monitoring. An onboard voltage monitor will scan these onboard
voltages continuously: CPU1 Vcore, CPU2 Vcore, CPU1 Vtt, CPU2 Vtt, CPU1
DIMM, CPU2 DIMM, 1.1V, 1.5V, 1.8V, 3.3V, 12V, 5V, 3.3 Vsb, and VBAT. Once a
voltage becomes unstable, a warning is given or an error message is sent to the
screen. the user can adjust the voltage thresholds to defi ne the sensitivity of the
voltage monitor.

Fan Status Monitor with Firmware Control

The PC health monitor can check the RPM status of the cooling fans. The onboard
CPU and chassis fans are controlled by Thermal Management via BIOS (under
Hardware Monitoring in the Advanced Setting).

Environmental Temperature Control

The thermal control sensor monitors the CPU temperature in real time and will turn
on the thermal control fan whenever the CPU temperature exceeds a user-defi ned
threshold. The overheat circuitry runs independently from the CPU. Once it detects
that the CPU temperature is too high, it will automatically turn on the thermal fan
control to prevent any overheat damage to the CPU. The onboard chassis thermal
circuitry can monitor the overall system temperature and alert users when the chas­sis temperature is too high.

Warning! To avoid system overheating, be sure to provide adequate air
fl ow to the system.

System Resource Alert

This feature is availab le when used with S upero Doctor III in the Windows OS

1-10

Chapter 1: Introduction

environment or used with Supero Doctor II in Linux. Supero Doctor is used to
notif y the user of cer tain system events. For example, you can also confi gure
Supero Doctor to provide you with warnings when the system temperature, CPU
temperat ures, volt ages a nd fan spe eds go beyon d a pre- defi ned range.

1-5 ACPI Features

ACPI stands for Advanced Confi guration and Power Interface. The ACPI specifi ca-
tion defi nes a fl exible and abstract hardware interface that provides a standard
way to integrate power management features throughout a PC system, including
its hardware, operating system and application software. This enables the system
to automatically turn on and off peripherals such as CD-ROMs, network cards, hard
disk drives and printers.

In addition to enabling operating system-directed power management, ACPI
provides a generic system event mechanism for Plug and Play and an operating
system-independent interface for confi guration control. ACPI leverages the Plug
and Play BIOS data structures while providing a processor architecture-independent
implementation that is compatible with both Windows 2000 and Windows 2003
Operating Systems.

Slow Blinking LED for Suspend-State Indicator

When the CPU goes into a suspend state, the chassis power LED will start blinking
to indicate that the CPU is in suspend mode. When the user presses any key, the
CPU will wake-up and the LED will automatically stop blinking and remain on.

Main Switch Override Mechanism

When an ATX power supply is used, the power button can function as a system
suspend button to make the system enter a SoftOff state. The monitor will be
suspended and the hard drive will spin down. Pressing the power button again
will cause the whole system to wake-up. During the SoftOff state, the ATX power
supply provides power to keep the required circuitry in the system "alive." In case
the system malfunctions and you want to turn off the power, just press and hold
the power button for 4 seconds. This option can be set in the Power section of the
BIOS Setup routine.

1-6 Power Supply

As with all computer products, a stable power source is necessary for proper and
reliable operation. It is even more important for processors that have high CPU
clock rates.

1-11

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

The X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF can accommodate 24-pin ATX power
supplies. Although most power supplies generally meet the specifi cations required
by the CPU, some are inadequate. In addition, the two 12V 8-pin power connections
are also required to ensure adequate power supply to the system. Also your power
supply must supply 1.5A for the Ethernet ports.

Warning: To prevent damage to the power supply or motherboard, please
use a power supply that contains a 24-pin and two 8-pin power connectors.
Be sure to connect these connectors to the 24-pin (JPW1) and the two
8-pin (JPW2,JPW3) power connectors on the motherboard for adequate
power supply to your system. Failure in doing so will void the manufacturer
warranty on your power supply and motherboard.

It is strongly recommended that you use a high quality power supply that meets ATX
power supply Specifi cation 2.02 or above. It must also be SSI compliant (For more
information, please refer to the website at http://www.ssiforum.org/). Additionally, in
areas where noisy power transmission is present, you may choose to install a line
fi lter to shield the computer from noise. It is recommended that you also install a
power surge protector to help avoid problems caused by power surges.

1-7 Super I/O

The Super I/O supports 360 K, 720 K, 1.2 M, 1.44 M or 2.88 M disk drives and data
transfer rates of 250 Kb/s, 500 Kb/s or 1 Mb/s. It also provides two high-speed,
16550 compatible serial communication ports (UARTs). Each UART includes a 16­byte send/receive FIFO, a programmable baud rate generator, complete modem
control capability and a processor interrupt system. Both UARTs provide legacy
speed with baud rate of up to 115.2 Kbps as well as an advanced speed with baud
rates of 250 K, 500 K, or 1 Mb/s, which support higher speed modems.

The Super I/O provides functions that comply with ACPI (Advanced Confi guration
and Power Interface), which includes support of legacy and ACPI power manage­ment through an SMI or SCI function pin. It also features auto power management
to reduce power consumption.

1-8 Overview of the Winbond WPCM450 Controller (For
X8DTH-6F/iF Only)

The Winbond WPCM450 Controller is a Baseboard Management Controller

(BMC) that supports the 2D/VGA-compatible Graphics Core with the PCI interface,
Virtual Media, and Keyboard/Video/Mouse Redirection (KVMR) modules. With
blade-oriented Super I/O capability built-in, the WPCM450 Controller is ideal for
legacy-reduced server platforms.

1-12

Chapter 1: Introduction

The Winbond WPCM450 Controller interfaces with the host system via a PCI inter­face to communicate with the Graphics core. It supports USB 2.0 and 1.1 for remote
keyboard/mouse/virtual media emulation. It also provides LPC interface to control
Super IO functions. The Winbond WPCM450 BMC is connected to the network via
an external Ethernet PHY module.

The Winbond WPCM450 BMC communicates with onboard components via
six SMBus interfaces, fan control, and Platform Environment Control Interface
(PECI).

1-13

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

Notes

1-14

Chapter 2: Installation

Chapter 2

Installation

2-1 Static-Sensitive Devices

Electrostatic Discharge (ESD) can damage electronic com ponents. T o prevent dam­age to your system board, it is important to handle it very carefully. The following
measures are generally suffi cient to protect your equipment from ESD.

Precautions

Use a grounded wrist strap designed to prevent static discharge.•

Touch a grounded metal object before removing the board from the antistatic •
bag.

Handle the board by its edges only; do not touch its components, peripheral

•

chips, memory modules or gold contacts.

When handling chips or modules, avoid touching their pins.

•

Put the motherboard and peripherals back into their antistatic bags when not •
in use.

For grounding purposes, make sure your computer chassis provides excellent

•

conductivity between the power supply, the case, the mounting fasteners and
the motherboard.

Use only the correct type of onboard CMOS battery as specifi ed by the

•

manufacturer. Do not install the onboard battery upside down to avoid possible
explosion.

Unpacking

The motherboar d is shipped i n a ntistati c pa ckaging to avoid static da mage. When
unpacking the board, make sure the person handling it is static protected.

2-1

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

2-2 Motherboard Installation

All motherboards have standard mounting holes to fi t different types of chassis.
Make sure that the locations of all the mounting holes for both motherboard and
chassis match. Although a chassis may have both plastic and metal mounting
fasteners, metal ones are highly recommended because they ground the mother­board to the chassis. Make sure that the metal standoffs click in or are screwed in
tightly. Then use a screwdriver to secure the motherboard onto the motherboard
tray. Note: Some components are very close to the mounting holes. Please take
precautionary measures to prevent damage to these components when installing
the motherboard to the chassis.

Tools Needed

1. Phillips Screwdriver

2. Pan head #6 screws

Locations of Mounting Holes

Installation Instructions

Install the IO shield into the chassis. 1.

Locate the mounting holes on the moth-2.
erboard. Refer to the layout above for
mounting hole locations.

Locate the matching mounting holes on 3.
the chassis. Align the mounting holes on
the motherboard against the mounting
holes on the chassis.

Install standoffs in the chassis as needed.4.

Install the motherboard into the chassis carefully to avoid damage to mother-5.
board components.

Warning: To avoid damaging the motherboard and its components, please
do not apply any force greater than 8 lb/sq.in (8 lbs. per square inch) when
installing a screw into a mounting hole.

X8DTH

Rev. 2.0

Insert a Pan head #6 screw into a mounting hole on the motherboard and its 6.
matching mounting hole on the chassis, using a Phillips screwdriver.

Repeat Step 4 to insert #6 screws to all mounting holes.7.

Make sure that the motherboard is securely placed on the chassis.8.

2-2

2-3 Processor and Heatsink Installation

!

When handling the processor package, avoid placing direct pressure on
the label area of the fan.

Notes:

Always connect the power cord last and always remove it before adding, re-1.
moving or changing any hardware components. Make sure that you install the
processor into the CPU socket before you install the CPU heatsink.

Make sure to install the motherboard into the chassis before you install the 2.
CPU heatsink and heatsink fans.

When purchasing a motherboard without a 5500 Series processor pre-3.
installed, make sure that the CPU socket plastic cap is in place, and none of
the CPU socket pins are bent; otherwise, contact the retailer immediately.

Chapter 2: Installation

Refer to the M B Features S ecti on for mo re deta ils on CPU s uppor t.4.

Installing an LGA 1366 Processor

Press the socket clip to release 1.
the load plate, which covers the
CPU socket, from its locking
position.

Gently lift the socket clip to 2.
open the load plate.

Socket Clip

Plastic Cap

Load Plate

Hold the plastic cap at its north 3.
and south center edges to re­move it from the CPU socket.

Hold the north & south edges of
the plastic cap to remove it

2-3

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

After removing the plastic cap, 1.
using your thumb and the index
fi nger, hold the CPU at the

CPU CPU SocketLoad Plate

north and south center edges.

Align the CPU key, the semi-2.
circle cutout, against the socket
key, the notch below the gold
color dot on the side of the
socket.

Once both the CPU and the 3.
socket are aligned, carefully
lower the CPU straight down

Socket Keys

into the socket. (Do not rub the
CPU against the surface of the
socket or its pins to avoid dam­aging the CPU or the socket.)

With the CPU inside the socket, 4.
inspect the four corners of the
CPU to make sure that the CPU
is properly installed.

Once the CPU is securely 5.
seated on the socket, lower the
CPU load plate to the socket.

Use your thumb to gently push 6.
the socket clip down to the clip
lock.

Warning: Please s ave the
plastic cap. The mother­board must be shipped
with the plastic cap prop­erly ins tal led to p rotec t the
CPU socket pins. Ship­ment without the plastic
cap properly installed will
cause damage to the sock­et pins.

CPU Keys

2-4

Installing a CPU Heatsink

Do not apply any thermal 1.
grease to the heatsink or the
CPU die because the required
amount has already been ap­plied.

Chapter 2: Installation

Place the heatsink on top of the 2.
CPU so that the four mounting
holes are aligned with those on
the retention mechanism.

3. Install two diagonal screws (ie
the #1 and the #2 screws) and
tighten them until just snug (-do
not fully tighten the screws to
avoid possible damage to the
CPU.)

Screw#1

Screw#1

Install Screw#1

Screw#2

Screw#2

4. Finish the installation by fully
tightening all four screws.

2-5

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

Removing the Heatsink

Warni ng: We do not recommend that the CPU or the heatsink be re­moved. However, if you do need to remove the heatsink, please follow
the inst ructions be low to uninstall th e heatsink and prevent da mage to
the CPU or ot her co mpone nts.

Unplug the power cord from the 1.
power supply.

Disconnect the heatsink fan 2.
wires from the CPU fan header.

Using a screwdriver, loosen and 3.
remove the heatsink screws
from the motherboard in the se­quence as show in the picture
on the right.

Using a screwdriver to
remove Screw#1

Hold the heatsink as shown 4.
in the picture on the right and
gently wriggle the heatsink to
loosen it from the CPU. (Do not
use excessive force when wrig­gling the heatsink.)

Once the heatsink is loosened, 5.
remove it from the CPU socket.

To reinstall the CPU and the 6.
heatsink, clean the surface of
the CPU and the heatsink to get
rid of the old thermal grease.
Reapply the proper amount of
thermal grease on the surface
before reinstalling them on the
motherboard.

Remove Screw#2

2-6

Chapter 2: Installation

2-4 Memory Installation

Note: Check the S uper micr o website fo r rec ommen ded mem or y modul es.

CAUTION

Exercise extreme care when installing or removing DIMM

module s to prevent any po ssib le damag e. Also n ote that th e

memor y is i nterl eaved to imp rove per fo rman ce (See ste p 1).

DIMM Installation

Insert the desired number of DIMMs into the memory slots, starting with 1.
DIMM #P1-DIMM1A. When populating DIMM modules always start with Chan­nel1 (#P1-DIMM1A and 1B) fi rst. For optimal memory performance, please
use memory modules of the same type and the same speed on the mother­board. (See the Memory Installation Table Below.)

Insert each DIMM module vertically into its slot. Pay attention to the notch 2.
along the bottom of the module to prevent inserting the DIMM module incor­rectly.

Gently press down on the DIMM module until it snaps into place in the slot. 3.
Repeat for all modules.

Memory Support

The X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF supports up to 96 GB of Registered
ECC or 24 GB of Unbuffered ECC/Non-ECC DDR3 1333/1066/800 MHz Memory
in 12 DIMMs.

Memory Population for Optimal Performance

-For a motherboard with One CPU (CPU1) installed

Branch 0 Branch 1 Branch 2

3 DIMMs P1 DIMM1A P1 DIMM2A P1 DIMM3A
6 DIMMs P1 DIMM1A P1 DIMM1B P1 DIMM2A P1 DIMM2B P1 DIMM3A P1 DIMM3B

Memory Population for Optimal Performance

-For a motherboard with Two CPUs installed

Branch 0 Branch 1 Branch 3 Branch 0 Branch 1 Branch 3

6 DIMMs 1A 2A 3A 1A 2A 3A
12

DIMMs

1A 1B 2A 2B 3A 3B 1A 1B 2A 2B 3A 3B

CPU1 CPU2

2-7

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

Note: Memory speed support depends on the CPU used on the moth­erboard.

DIMM Module Population Confi guration

For memor y to wor k pro perl y, follow the tab les be low for me mor y inst allati on:

DIMM Population Table

DIMM
Slots per
Channel

2 1 FBD DDR3 ECC 1066,1333 SR, DR
2 1 FBD DDR3 ECC 1066 QR
2 2 FBD DDR3 ECC 1066,1333 SR, DR
2 2 FBD DDR3 ECC 1066 SR, DR, QR

DIMM
Slots per
Channel

2 1 Unb. ECC/NON-ECC DDR3 800,1066,1333 SR or DR
2 2 Unb. ECC/NON-ECC DDR3 800,1066 Mixing SR, DR

DIMMs
Populated
per Channel

DIMMs
Populated
per Channel

DIMM Type (FBD=
Fully Buffered)

UDIMM (Unbuffered DIMM) Population Table

DIMM Type
(Unb.= Unbuffered)

Speeds (in MHz) Ranks per DIMM

Speeds (in
MHz)

(any combination;
SR=Single Rank,
DR=Dual Rank,
QR=Quad Rank)

Ranks per DIMM
(Mixing: any
combination;
SR=Single Rank,
DR=Dual Rank)

Note 1: Due to OS limitations, some operating systems may not show

more than 4 GB of memory.
Note 2: Due to memory allocation to system devices, the amount of

memory that r ema ins avai lab le fo r op erat io nal u se wi ll be r edu ce d wh en
4 GB of R A M is us ed. T he re duc tio n in me mor y ava ilab ili ty i s disp rop or­tiona l. (See the fo llowi ng Mem or y Availabi lity Table.)

2-8

Possible System Memory Allocation & Availability

Chapter 2: Installation

System Device Size Physical Memory

Remaining (-Available) (4 GB Total System
Memory)

Firmware Hub fl ash memory (System

1 MB 3.99 GB

BIOS)
Local APIC 4 KB 3.99 GB
Area Reserved for the chipset 2 MB 3.99 GB
I/O APIC (4 Kbytes) 4 KB 3.99 GB
PCI Enumeration Area 1 256 MB 3.76 GB
PCI Express (256 MB) 256 MB 3.51 GB
PCI Enumeration Area 2 (if needed)

512 MB 3.01 GB

-Aligned on 256-MB boundary­VGA Memory 16 MB 2.85 GB
TSEG 1 MB 2.84 GB
Memory available for the OS & other

2.84 GB

applications

Installing and Removing DIMMs

Notch

DIMM DDR3

Notch

X8DTH

Rev. 2.0

Release Tab

Release

Tab

Note: Notch

should align

with the

receptive point

on the slot

Release

Tab

To Install : Insert module vertically and press down
until it s naps i nto pla ce. Pay at tent ion to t he ali gn ­ment not ch at th e bot tom.

3

Release Tab

To Remove:

Use your thumbs to gently push the release
tabs near both ends of the module. This should
release it from the slot.

2-9

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

123

4

5

6

789

2-5 Control Panel Connectors/IO Ports

The I/O p ort s are col or cod ed in co nforma nce wit h the PC 9 9 speci fi cation. See
the pic ture be low for t he co lors a nd loc atio ns of the var ious I /O por t s.

1. Back Panel Connectors/IO Ports

X8DTH

Rev. 2.0

Back Panel I/O Port Locations and Defi nitions

Back Panel Connectors

Keyboard (Purple)1.
PS/2 Mouse (Green)2.
USB 03.
USB 14.
IPMI_Dedicated LAN (X8DTH-iF/6F only)5.
COM Port 16.
VGA (Blue) 7.
LAN 18.
LAN 29.

2-10

Chapter 2: Installation

1

2

ATX PS/2 Keyboard and PS/2
Mouse Ports

The ATX PS/2 keyboard and PS/2
mouse are located next to the Back
Panel USB ports on the motherboard.
See the table at right for pin defi ni-
tions.

PS/2 Keyboard/Mouse Pin

Defi nitions

PS2 Keyboard PS2 Mouse
Pin# Defi nition Pin# Defi nition
1 KB Data 1 Mouse Data
2 No Connection 2 No Connection
3 Ground 3 Ground

4 Mouse/KB VCC

(+5V)
5 KB Clock 5 Mouse Clock
6 No Connection 6 No Connection
VCC: with 1.5A PTC (current limit)

4 Mouse/KB VCC

(+5V)

X8DTH

Rev. 2.0

1. Keyboard (Purple)

2. Mouse (Green)

2-11

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

1

2

3

Serial Ports

Two COM connections (COM1 & COM_
DBG) are located on the motherboard.
COM1 is located on the Backplane IO
panel, and COM2 is located close to
PCI-E Slot1 to provide serial connec­tions to the motherboard. See the table
on the right for pin defi nitions.

COM1

COM2

Video Connector

Serial Ports

Pin Defi nitions

Pin # Defi nition Pin # Defi nition
1 DCD 6 DSR
2 RXD 7 RTS
3 TXD 8 CTS
4 DTR 9 RI
5 Ground 10 N/A

A Video (VGA) connector is located
next to COM Port1 on the IO back­plane. This connector is used to pro­vide video display. Refer to the board
layout below for the location.

1. COM 1

2. COM 2

3. VGA

X8DTH

Rev. 2.0

2-12

Chapter 2: Installation

1

2

345

Universal Serial Bus (USB)

Two Universal Serial Bus ports (USB
0/1) are located on the I/O back panel.
Additionally, five USB connections
(USB 3, 4/5, 6/7) are on the mother­board to provide front chassis access.
(Cables are not included). See the
tables on the right for pin defi nitions.

Back Panel USB

(USB 0/1)

Pin# Defi nitions
1 +5V
2 PO­3 PO+
4 Ground
5 N/A

Pin Defi nitions (USB 4/5, 6/7)

USB4/6
Pin # Defi nition

1 +5V 1 +5V
2 PO- 2 PO­3 PO+ 3 PO+
4 Ground 4 Ground
5 Key 5 No connection

Front Panel USB

(USB 3)

Pin# Defi nition
1 Vcc
2 Data­3 Data+
4 Ground
5NA

Front Panel USB

USB 5/7
Pin # Defi nition

X8DTH

Rev. 2.0

1. Backpanel USB 0

2. Backpanel USB 1

3. Front panel USB 3

4. Front panel USB 4/5

5. Front panel USB 6/7

2-13

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

1

2

3

Ethernet Ports

Two Ethernet ports (LAN 1/LAN2) are
located at on the IO backplane. In
addition, a dedicated LAN is also lo­cated on the X8DTH-iF/6F to provide
KVM support for IPMI 2.0. All these
ports accept RJ45 type cables. (Note:
Please refer to the LED Indicator Sec­tion for LAN LED information.)

LAN Ports

Pin Defi nition

Pin# Defi nition
1 P2V5SB 10 SGND
2 TD0+ 11 Act LED
3 TD0- 12 P3V3SB
4 TD1+ 13 Link 100 LED

(Yellow, +3V3SB)

5 TD1- 14 Link 1000 LED

(Yellow, +3V3SB)
6 TD2+ 15 Ground
7 TD2- 16 Ground
8 TD3+ 17 Ground
9 TD3- 88 Ground

(NC: No Connection)

X8DTH

Rev. 2.0

1. LAN1

2. LAN2

3. IPMI LAN (X8DTH-iF/6F only)

2-14

Chapter 2: Installation

2. Front Control Panel

JF1 contains header pins for various buttons and indicators that are normally located
on a control panel at the front side of the chassis. These connectors are designed
specifi cally for use with Supermicro server chassis. See the fi gure below for the
descriptions of the various control panel buttons and LED indicators. Refer to the
following section for descriptions and pin defi nitions.

JF1 Header Pins

X8DTH

Rev. 2.0

Ground

Power LED

HDD LED

NIC1 LED

NIC2 LED

1920

NMI

X

X

Vcc

Vcc

Vcc

Vcc

OH/Fan Fail LED

PWR Fail LED

Ground

Ground

2-15

Vcc

Vcc

Reset

PWR

2

1

Reset Button

Power Button

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

3. Front Control Panel Pin Defi nitions

NMI Button

The non-maskable interrupt button
header is located on pins 19 and 20
of JF1. Refer to the table on the right
for pin defi nitions.

Power LED

The Power LED connection is located
on pins 15 and 16 of JF1. Refer to the
table o n the ri ght for p in defi nitions.

NMI Button

Pin Defi nitions (JF1)

Pin# Defi nition
19 Control
20 Ground

Power LED

Pin Defi nitions (JF1)

Pin# Defi nition
15 +5V
16 Ground

X8DTH

Rev. 2.0

2-16

A. NMI
B. PWR LED

Ground

X

Power LED

B

HDD LED

NIC1 LED

NIC2 LED

OH/Fan Fail LED

PWR Fail LED

Ground

Ground

1920

NMI

A

X

Vcc

Vcc

Vcc

Vcc

Vcc

Vcc

Reset

Reset Button

Power Button

PWR

2

1

Chapter 2: Installation

HDD LED

The HDD LED connection is located
on pins 13 and 14 of JF1. Attach a
cable here to indicate HDD activ­ity. See the table on the right for pin
defi nitions.

NIC1/NIC2 LED Indicators

The NIC (Network Interface Control­ler) LED connection for GLAN port 1 is
located on pins 11 and 12 of JF1, and
the LED connection for GLAN Port 2
is on Pins 9 and 10. Attach the NIC
LED cables to display network activity .
Refer to the table on the right for pin
defi nitions.

HDD LED

Pin Defi nitions (JF1)

Pin# Defi nition
13 +5V
14 HD Active

GLAN1/2 LED

Pin Defi nitions (JF1)

Pin# Defi nition
9/11 Vcc
10/12 Ground

X8DTH

Rev. 2.0

A

B

C

OH/Fan Fail LED

2-17

Ground

X

Power LED

HDD LED

NIC1 LED

NIC2 LED

PWR Fail LED

Ground

Ground

A. HDD LED
B. NIC1 LED
C. NIC2 LED

1920

Vcc

Vcc

Vcc

Vcc

Vcc

Reset

PWR

2

1

NMI

X

Vcc

Reset Button

Power Button

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

Overheat (OH)/Fan Fail LED

Connect an LED cable to the OH/
Fan Fail connections on pins 7 and
8 of JF1 to provide advanced warn­ings for chassis overheat/fan failure.
Refer to the table on the right for pin
defi nitions.

Power Fail LED

The Power Fail LED connection is
locate d on pins 5 and 6 of JF1. Re­fer to the table on the right for pin
defi nitions.

OH/Fan Fail LED

Pin Defi nitions (JF1)

Pin# Defi nition
7 Vcc
8 OH/Fan Fail LED

OH/Fan Fail Indicator

Status

State Defi nition
Off Normal
On Overheat
Flash-

ing

Pin Defi nitions (JF1)

Pin# Defi nition
5 Vcc
6 Ground

Fan Fail

PWR Fail LED

X8DTH

Rev. 2.0

A

OH/Fan Fail LED

B

PWR Fail LED

2-18

Ground

Power LED

HDD LED

NIC1 LED

NIC2 LED

A. OH/Fan Fail LED
B. PWR Supply Fail

1920

X

Ground

Ground

2

Reset

1

NMI

X

Vcc

Vcc

Vcc

Vcc

Vcc

Vcc

PWR

Reset Button

Power Button

Chapter 2: Installation

Reset Button

The Reset Button connection is located
on pins 3 and 4 of JF1. Attach it to a
hardware reset switch on the computer
case. Refer to the table on the right for
pin defi nitions.

Power Button

The Power Button connection is located
on pins 1 and 2 of JF1. Momentarily con­tacting both pins will power on/off the sys­tem. This button can also be confi gured
to function as a suspend button (with a
setting in the BIOS - see Chapter 4). To
turn off the power when set to suspend
mode, press the button for at least 4
seconds. Refer to the table on the right
for pin defi nitions.

Reset Button

Pin Defi nitions (JF1)

Pin# Defi nition
3 Reset
4 Ground

Power Button

Pin Defi nitions (JF1)

Pin# Defi nition

1 Signal
2 +3V Standby

X8DTH

Rev. 2.0

Power LED

HDD LED

NIC1 LED

NIC2 LED

OH/Fan Fail LED

PWR Fail LED

2-19

Ground

X

Ground

Ground

A. Reset Button
B. PWR Button

1920

NMI

X

Vcc

Vcc

Vcc

Vcc

Vcc

Vcc

Reset

PWR

2

1

Reset Button

Power Button

A

B

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

2-6 Connecting Cables

Power Connectors

A 24-pin main power supply connector(JPW1)
and two 8-pin CPU PWR connectors (JPW2/
JPW3) on the motherboard. These power
connectors meet the SSI EPS 12V specifi -
cation. In addition to the 24-pin ATX power
connector, the 12V 8-pin CPU PWR connec­tors at JPW2/JPW3 must also be connected
to your power supply. See the table on the
right for pin defi nitions.

Warning: To prevent damage to
the power supply or motherboard,
please use a power supply that
contains a 24-pin and two 8-pin
power connectors. Be sure to
connect these connectors to the
24-pin (JPW1) and the two 8-pin
(JPW2,JPW3) power connectors
on the motherboard. Failure in do­ing so will void the manufacturer
warranty on your power supply and
motherboard.

FAN5

KB/MS

FAN6

USB0/1

IPMI_LAN

COM1

P2-DIMM3A

P2-DIMM3B

P2-DIMM2A

P2-DIMM2B

P2-DIMM1A

P2-DIMM1B

ATX Power 24-pin Connector

Pin Defi nitions

Pin# Defi nition Pin # Defi nition
13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 COM 3 COM
16 PS_ON 4 +5V
17 COM 5 COM
18 COM 6 +5V
19 COM 7 COM
20 Res (NC) 8 PWR_OK
21 +5V 9 5VSB
22 +5V 10 +12V
23 +5V 11 +12V
24 COM 12 +3.3V

12V 8-pin PWR Connector

Pin Defi nitions

Pins Defi nition
1 through 4 Ground
5 through 8 +12V

(Required)

A. 24-pin ATX PWR (Req'd)
B/C.8-pin Processor PWR
(Req'd)

A

JPI2C

JPW1

CPU1

C

B

JPW2

JPW3

FAN1

FAN7

VGA

PHY

LAN1

LAN2

FAN8

JPL1

LAN CTRL

BMC

DP5

TPM

Slot7 PCI-E 2.0 X8

Slot6 PCI-E 2.0 X8

Slot5 PCI-E 2.0 X8

JI2C2

JI2C1

Slot4 PCI-E 2.0 X8

Slot3 PCI-E 2.0 X8

Slot2 PCI-E 2.0 X8

Slot1 PCI-E 2.0 X8

COM2

JHB1

JPG1

JPB

1

1

1

Wake-On-LAN

JWOL1

CPU2

USB6/7

USB4/5

(South Bridge)

USB3

(IOH36D-2)

Intel
ICH10R

SATA-SGPIO1

SATA-SGPIO0

JF1

PWR_LED

DP4

P1-DIMM1B

P1-DIMM1A

P1-DIMM2B

P1-DIMM2A

P1-DIMM3B

P1-DIMM3A

X8DTH

(IOH36D-1)

LED5

SAS Activity

JWF1

I-SATA1

Rev. 2.0

Intel

5520

DP6

LSI

DP7

SAS2008

JPS1

I-SATA0

RAID Key

Intel

5520

JBT1

SPI BIOS

I-SATA5

I-SATA3

I-SATA4

I-SATA2

JWD

FAN2

SMBus1

JOH1

JD1

FAN3

Battery

Buzzer

SAS

FLASH

SAS0~3

SAS4~7

FAN4

JL1

2-20

Chapter 2: Installation

D

E

F

G

Fan Headers

This motherboard has eight CPU/system
fan headers (Fan 1 to Fan8) on the moth­erboard. All these 4-pin fans headers are
backward compatible with the traditional
3-pin fans. However, fan speed control
is available for 4-pin fans only. The fan
speeds are controlled by Thermal Man­agement via Hardware Monitoring in
the Advanced Setting in the BIOS. (The
Default setting is Disabled.) See the table
on the right for pin defi nitions.

Chassis Intrusion

A Chassis Intrusion header is located
at JL1 on the motherboard. Attach an
appropriate cable from the chassis to
inform you of a chassis intrusion when
the chassis is opened.

Fan Header

Pin Defi nitions

Pin# Defi nition
1 Ground
2 +12V
3 Tachometer
4 PWR Modulation

Chassis Intrusion

Pin Defi nitions (JL1)

Pin# Defi nition
1 Intrusion Input
2 Ground

A. Fan 1

FAN5

KB/MS

FAN6

USB0/1

IPMI_LAN

COM1

VGA

PHY

LAN1

LAN2

FAN8

JPL1

LAN CTRL

BMC

DP5

TPM

P2-DIMM3A

P2-DIMM3B

P2-DIMM2A

P2-DIMM2B

P2-DIMM1A

P2-DIMM1B

CPU2

H

Slot7 PCI-E 2.0 X8

Slot6 PCI-E 2.0 X8

Slot5 PCI-E 2.0 X8

JI2C2

JI2C1

Slot4 PCI-E 2.0 X8

Slot3 PCI-E 2.0 X8

Slot2 PCI-E 2.0 X8

Slot1 PCI-E 2.0 X8

COM2

Wake-On-LAN

JHB1

JPG1

JPB

1

1

JWOL1

1

USB6/7

(IOH36D-2)

Intel
ICH10R

(South Bridge)

SATA-SGPIO1

USB3

USB4/5

SATA-SGPIO0

JPI2C

JPW2

JPW1

JPW3

FAN1

A

B. Fan 2
C. Fan 3
D. Fan 4

CPU1

P1-DIMM1B

P1-DIMM1A

P1-DIMM2B

P1-DIMM2A

P1-DIMM3B

P1-DIMM3A

X8DTH

(IOH36D-1)

LED5

SAS Activity

JWF1

I-SATA1

Rev. 2.0

Intel

5520

DP6

LSI

DP7

SAS2008

JPS1

I-SATA0

RAID Key

Intel

5520

JBT1

SPI BIOS

I-SATA5

I-SATA3

I-SATA4

I-SATA2

FAN7

JF1

PWR_LED

DP4

FAN2

JOH1

FAN3

Battery

Buzzer

SAS

FLASH

SAS0~3

SAS4~7

FAN4

JL1

E. Fan 5
F. Fan 6
G. Fan 7

JWD

H. Fan 8

B

SMBus1

I. Chassis Intrusion

JD1

C

I

2-21

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

Power LED/Speaker

On the JD1 header, pins 1-3 are used
for power LED indication, and pins 4-7
are for the speaker. See the tables
on the right for pin defi nitions. Please
note that the speaker connector pins
(4-7) are for use with an external
speaker. If you wish to use the on­board speaker, you should close pins
6-7 with a jumper.

Wake-On-LAN

The Wake-On-LAN header is located
at JWOL on the motherboard. You
must also have a LAN card with a
Wake-On-LAN connector and a cable
to use this feature. See the table on
the right for pin defi nitions.

PWR LED Connector

Pin Defi nitions

Pin Setting Defi nition
Pin 1 Anode (+)
Pin2 Cathode (-)
Pin3 NA

Speaker Connector

Pin Defi nitions

Pin Setting Defi nition
Pins 4-7 External Speaker
Pins 6-7 Internal Speaker

Wake-On-LAN

Pin Defi nitions

Pin# Defi nition
1 +5V Standby
2 Ground
3 Wake-up

A. PWR LED/Speaker

FAN5

KB/MS

FAN6

USB0/1

IPMI_LAN

COM1

VGA

PHY

LAN1

LAN2

FAN8

JPL1

LAN CTRL

BMC

DP5

TPM

P2-DIMM3A

P2-DIMM3B

P2-DIMM2A

P2-DIMM2B

P2-DIMM1A

P2-DIMM1B

CPU2

Slot7 PCI-E 2.0 X8

Slot6 PCI-E 2.0 X8

Slot5 PCI-E 2.0 X8

JI2C2

JI2C1

Slot4 PCI-E 2.0 X8

Slot3 PCI-E 2.0 X8

Slot2 PCI-E 2.0 X8

Slot1 PCI-E 2.0 X8

B

COM2

Wake-On-LAN

JHB1

JPG1

JPB

1

1

JWOL1

1

USB6/7

(IOH36D-2)

Intel

ICH10R

(South Bridge)

SATA-SGPIO1

USB3

USB4/5

SATA-SGPIO0

JPI2C

CPU1

P1-DIMM1B

P1-DIMM1A

P1-DIMM2B

P1-DIMM2A

P1-DIMM3B

P1-DIMM3A

Intel

5520

Intel

5520

(IOH36D-1)

JBT1

I-SATA5

I-SATA4

SPI BIOS

I-SATA2

I-SATA3

LED5

SAS Activity

JWF1

I-SATA1

JPW1

DP6
DP7

X8DTH

Rev. 2.0

JPS1

I-SATA0

RAID Key

LSI
SAS2008

JPW2

JPW3

B. WOL

FAN1

FAN7

JF1

PWR_LED

DP4

JWD

FAN2

SMBus1

JOH1

A

JD1

FAN3

Battery

Buzzer

SAS

FLASH

SAS0~3

SAS4~7

FAN4

JL1

2-22

Chapter 2: Installation

Overheat LED/Fan Fail (JOH1)

The JOH1 header is used to connect
an LED indi c ato r to p rov id e war n in gs
of chass is overhe ating or fa n failure.
This LED will blink when a fan failure
occu rs . Refer t o th e ta bl e on r i ght f or
pin defi nitions.

SATA-SGPIO 0/1 Headers

Two SATA-SGPIO (General Pur­pose Input/Output) headers (SATA­SGPIO-0/SATA-SGPIO-1) are located
the motherboard. These headers
support serial link interfaces for the
onboard SATA connectors. See the
table on the right for pin defi nitions.
Refer to the board layout below for
the location.

Overheat LED

Pin Defi nitions

Pin# Defi nition
1 5vDC
2 OH Active

OH/Fan Fail LED

Pin Defi nitions

State Message
Solid Overheat
Blinking Fan Fail

SATA-SGPIO

Pin Defi nitions

Pin# Defi nition Pin Defi nition
1NC 2 NC
3 Ground 4 Data

5 Load 6 Ground
7NC 8 NC

Note: NC= No Connections

A. OH/Fan Fail LED

FAN5

KB/MS

FAN6

USB0/1

IPMI_LAN

COM1

VGA

PHY

LAN1

LAN2

FAN8

JPL1

LAN CTRL

BMC

DP5

TPM

P2-DIMM3A

P2-DIMM3B

P2-DIMM2A

P2-DIMM2B

P2-DIMM1A

P2-DIMM1B

CPU2

Slot7 PCI-E 2.0 X8

Slot6 PCI-E 2.0 X8

Slot5 PCI-E 2.0 X8

JI2C2

JI2C1

Slot4 PCI-E 2.0 X8

Slot3 PCI-E 2.0 X8

Slot2 PCI-E 2.0 X8

Slot1 PCI-E 2.0 X8

COM2

Wake-On-LAN

JHB1

JPG1

JPB

1

1

JWOL1

1

USB6/7

(IOH36D-2)

Intel
ICH10R

(South Bridge)

SATA-SGPIO1

USB3

USB4/5

SATA-SGPIO0

JPI2C

JPW1

CPU1

P1-DIMM1B

P1-DIMM1A

P1-DIMM2B

P1-DIMM2A

P1-DIMM3B

P1-DIMM3A

Intel

5520

Intel

5520

(IOH36D-1)

JBT1

I-SATA5

C

I-SATA4

SPI BIOS

I-SATA2

I-SATA3

LED5

SAS Activity

JWF1

DP6

I-SATA1

DP7

X8DTH

Rev. 2.0

JPS1

I-SATA0

RAID Key

LSI
SAS2008

JPW2

JPW3

FAN1

FAN7

PWR_LED

DP4

Battery

Buzzer

SAS

FLASH

SAS0~3

SAS4~7

FAN4

B

B. SATA-SGPIO 0
C. SATA-SGPIO 1

JF1

JWD

FAN2

SMBus1

A

JOH1

JD1

FAN3

JL1

2-23

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

System Management Bus

A System Management Bus header
is located at SUBUS1 on the mother­board. Connect an appropriate cable
here to use the SMB connection on
your system.

Power SMB (I2C) Connector

Power System Management Bus (I

2

C)
Connector(JPI2C) monitors power
supply, fan status and system tem­perature. See the table on the right
for pin defi nitions.

SMB Header

Pin Defi nitions

Pin# Defi nition
1 Data
2 Ground
3 Clock
4 No Connection

PWR SMB

Pin Defi nitions

Pin# Defi nition
1 Clock
2 Data

3 PWR Fail
4 Ground
5 +3.3V

FAN5

KB/MS

FAN6

USB0/1

IPMI_LAN

COM1

VGA

PHY

LAN1

LAN2

FAN8

JPL1

LAN CTRL

BMC

DP5

TPM

P2-DIMM3A

P2-DIMM3B

P2-DIMM2A

P2-DIMM2B

P2-DIMM1A

P2-DIMM1B

CPU2

Slot7 PCI-E 2.0 X8

Slot6 PCI-E 2.0 X8

Slot5 PCI-E 2.0 X8

JI2C2

JI2C1

Slot4 PCI-E 2.0 X8

Slot3 PCI-E 2.0 X8

Slot2 PCI-E 2.0 X8

Slot1 PCI-E 2.0 X8

COM2

Wake-On-LAN

JHB1

JPG1

JPB

1

1

JWOL1

1

USB4/5

USB6/7

(South Bridge)

USB3

(IOH36D-2)

Intel

ICH10R

SATA-SGPIO1

SATA-SGPIO0

Intel

5520

B

JPI2C

CPU1

P1-DIMM1B

P1-DIMM1A

P1-DIMM2B

P1-DIMM2A

P1-DIMM3B

P1-DIMM3A

Intel

5520

(IOH36D-1)

JBT1

I-SATA5

I-SATA4

SPI BIOS

I-SATA2

I-SATA3

SAS Activity

JWF1

LED5

I-SATA1

JPW1

DP6

DP7

X8DTH

Rev. 2.0

JPS1

I-SATA0

RAID Key

LSI
SAS2008

JPW2

JPW3

FAN1

FAN7

JF1

PWR_LED

DP4

JWD

FAN2

SMBus1

JOH1

JD1

FAN3

Battery

Buzzer

SAS

FLASH

SAS0~3

SAS4~7

FAN4

JL1

A. SMB

JPI2C

B.

A

2-24

Chapter 2: Installation

Trusted Platform Module Header

A Trusted Platform Module (TPM)
header is located on the motherboard
to provide TPM support to enhance
data integrity and system security.
Refer to the table on the right for pin
defi nitions.

FP IPMI Heartbeat LED Header
(X8DTH-6F/iF Only)

The Front Panel IPMI Heartbeat LED
connection header (JHB1) is located
next to COM2 port. Connect a cable
here to indicate the status of IPMI
connection. See the layout for the
location of JHB1.

Trusted Platform Module (TPM) Header

Pin Defi nitions

Pin# Defi nition Pin # Defi nition
1 LPC Clock 2 GND
3 LPC FRAME# 4 Key
5 LPC Reset# 6 +5V (X)
7 LAD3 8 LAD2
9 +3.3V 10 LAD1
11 LAD0 12 GND
13 SCL 14 SDAT
15 +3V_DUAL 16 SERIRQ (X)
17 GND 18 CLKRUN(X)

19 LPCPD# (X) 20 LDRQ#(X)
Notes:
(X)=TPM does not use the signals.

2

SCL, SDAT are I

C bus clock and data.

A. TPM Header

FAN5

KB/MS

FAN6

USB0/1

IPMI_LAN

COM1

VGA

PHY

LAN1

LAN2

FAN8

JPL1

LAN CTRL

BMC

DP5

A

TPM

P2-DIMM3A

P2-DIMM3B

P2-DIMM2A

P2-DIMM2B

P2-DIMM1A

P2-DIMM1B

CPU2

Slot7 PCI-E 2.0 X8

Slot6 PCI-E 2.0 X8

Slot5 PCI-E 2.0 X8

JI2C2

JI2C1

Slot4 PCI-E 2.0 X8

Slot3 PCI-E 2.0 X8

Slot2 PCI-E 2.0 X8

Slot1 PCI-E 2.0 X8

COM2

B

Wake-On-LAN

JHB1

JPG1

JPB

1

1

JWOL1

1

USB6/7

(IOH36D-2)

Intel
ICH10R

(South Bridge)

SATA-SGPIO1

USB3

USB4/5

SATA-SGPIO0

JPI2C

CPU1

P1-DIMM1B

P1-DIMM1A

P1-DIMM2B

P1-DIMM2A

P1-DIMM3B

P1-DIMM3A

Intel

5520

Intel

5520

(IOH36D-1)

JBT1

I-SATA5

I-SATA4

SPI BIOS

I-SATA2

I-SATA3

LED5

SAS Activity

JWF1

I-SATA1

JPW1

DP6
DP7

X8DTH

Rev. 2.0

JPS1

I-SATA0

LSI
SAS2008

RAID Key

JPW2

JPW3

FAN1

FAN7

JF1

PWR_LED

DP4

JWD

FAN2

SMBus1

JOH1

JD1

FAN3

Battery

Buzzer

SAS

FLASH

SAS0~3

SAS4~7

FAN4

JL1

B. FP IPMI Heartbeat
LED Header

2-25

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

DOM Power Connector

A power connector for SATA DOM
(Disk_On_Module) Devices is located
at JWF1. Connect the appropriate
cable here to provide power support
for your DOM devices.

DOM PWR

Pin Defi nitions

Pin# Defi nition
1 +5V
2 Ground
3 Ground

A. DOM Power

FAN5

KB/MS

FAN6

USB0/1

IPMI_LAN

COM1

VGA

PHY

LAN1

LAN2

FAN8

JPL1

LAN CTRL

BMC

DP5

TPM

P2-DIMM3A

P2-DIMM3B

P2-DIMM2A

P2-DIMM2B

P2-DIMM1A

P2-DIMM1B

CPU2

Slot7 PCI-E 2.0 X8

Slot6 PCI-E 2.0 X8

Slot5 PCI-E 2.0 X8

JI2C2

JI2C1

Slot4 PCI-E 2.0 X8

Slot3 PCI-E 2.0 X8

Slot2 PCI-E 2.0 X8

Slot1 PCI-E 2.0 X8

COM2

Wake-On-LAN

JHB1

JPG1

JPB

1

1

JWOL1

1

USB6/7

(IOH36D-2)

Intel

ICH10R

(South Bridge)

SATA-SGPIO1

USB3

USB4/5

SATA-SGPIO0

JPI2C

CPU1

P1-DIMM1B

P1-DIMM1A

P1-DIMM2B

P1-DIMM2A

P1-DIMM3B

P1-DIMM3A

Intel

5520

Intel

5520

(IOH36D-1)

JBT1

I-SATA5

I-SATA4

SPI BIOS

I-SATA2

I-SATA3

LED5

SAS Activity

A

JWF1

I-SATA1

JPW1

DP6

DP7

X8DTH

Rev. 2.0

JPS1

I-SATA0

RAID Key

LSI
SAS2008

JPW2

JPW3

FAN1

FAN7

JF1

PWR_LED

DP4

JWD

FAN2

SMBus1

JOH1

JD1

FAN3

Battery

Buzzer

SAS

FLASH

SAS0~3

SAS4~7

FAN4

JL1

2-26

2-7 Jumper Settings

Connector

Pins

Jumper

Cap

Setting

Chapter 2: Installation

Explanation of Jumpers

To modify the operation of the mother­board, jumpers can be used to choose
between optional settings. Jumpers cre­ate shorts between two pins to change
the function of the connector. Pin 1
is identifi ed with a square solder pad
on the printed circuit board. See the
motherboard layout pages for jumper
locations.

Note: On two pin jumpers,
"Closed" means the jumper
is on and "Open" means the
jumper i s of f the pin s.

GLAN Enable/Disable

Use JPL1 to enable or disable GLAN
Port1/GLAN Port2 on the mother­board. See the table on the right for
jumper s ettings. The d efault settin g is

Enabled.

3 2 1

3 2 1

Pin 1-2 short

GLAN Enable

Jumper Settings

Pin# Defi nition
1-2 Enabled (default)
2-3 Disabled

A. GLAN Port 1/2 Enable

FAN5

KB/MS

FAN6

USB0/1

IPMI_LAN

COM1

VGA

PHY

LAN1

LAN2

FAN8

JPL1

A

LAN CTRL

BMC

DP5

TPM

P2-DIMM3A

P2-DIMM3B

P2-DIMM2A

P2-DIMM2B

P2-DIMM1A

P2-DIMM1B

CPU2

Slot7 PCI-E 2.0 X8

Slot6 PCI-E 2.0 X8

Slot5 PCI-E 2.0 X8

JI2C2

JI2C1

Slot4 PCI-E 2.0 X8

Slot3 PCI-E 2.0 X8

Slot2 PCI-E 2.0 X8

Slot1 PCI-E 2.0 X8

COM2

Wake-On-LAN

JHB1

JPG1

JPB

1

1

JWOL1

1

USB6/7

(IOH36D-2)

Intel
ICH10R

(South Bridge)

SATA-SGPIO1

USB3

USB4/5

SATA-SGPIO0

JPI2C

CPU1

P1-DIMM1B

P1-DIMM1A

P1-DIMM2B

P1-DIMM2A

P1-DIMM3B

P1-DIMM3A

Intel

5520

Intel

5520

(IOH36D-1)

JBT1

I-SATA5

I-SATA4

SPI BIOS

I-SATA2

I-SATA3

LED5

SAS Activity

JWF1

I-SATA1

JPW1

DP6
DP7

X8DTH

Rev. 2.0

JPS1

I-SATA0

LSI
SAS2008

RAID Key

JPW2

JPW3

FAN1

FAN7

JF1

PWR_LED

DP4

JWD

FAN2

SMBus1

JOH1

JD1

FAN3

Battery

Buzzer

SAS

FLASH

SAS0~3

SAS4~7

FAN4

JL1

2-27

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

CMOS Clear

JBT1 is used to clear CMOS. Instead of pins, this "jumper" consists of contact
pads to prevent t he accident al clearin g of CMOS. To clear CMOS , use a metal
objec t such as a sma ll screwdr iver to touc h both pad s at the same t ime to shor t
the co nnec ti on. A lways rem ove the AC p ower c ord f rom t he syste m befo re cl ear­ing CMOS.

Note: For an ATX power supply, you must completely shut down the sys­tem, remove the AC power cord and then short JBT1 to clear CMOS.

Watch Dog Enable/Disable

Watch Dog (JWD) is a syste m monitor th at
can reb oot t he sys tem w hen a s of tware ap­plicat ion han gs. Clo se Pins 1-2 to res et the
system if an app lication ha ngs. Close Pins
2-3 to generate a non-maskable interrupt
signal for the application that hangs. See the
table on the right for jumper settings. Watch
Dog must also be enabled in the BIOS.

FAN5

KB/MS

FAN6

USB0/1

IPMI_LAN

COM1

VGA

PHY

LAN1

LAN2

FAN8

JPL1

LAN CTRL

BMC

DP5

TPM

P2-DIMM3A

P2-DIMM3B

P2-DIMM2A

P2-DIMM2B

P2-DIMM1A

P2-DIMM1B

CPU2

Slot7 PCI-E 2.0 X8

Slot6 PCI-E 2.0 X8

Slot5 PCI-E 2.0 X8

JI2C2

JI2C1

Slot4 PCI-E 2.0 X8

Slot3 PCI-E 2.0 X8

Slot2 PCI-E 2.0 X8

Slot1 PCI-E 2.0 X8

COM2

Wake-On-LAN

JHB1

JPG1

JPB

1

1

JWOL1

1

USB6/7

(IOH36D-2)

Intel

ICH10R

(South Bridge)

SATA-SGPIO1

USB3

USB4/5

SATA-SGPIO0

JPI2C

P1-DIMM1A

P1-DIMM2B

P1-DIMM2A

P1-DIMM3B

P1-DIMM3A

Intel

5520

A

JBT1

SAS Activity

SPI BIOS

I-SATA5

I-SATA3

I-SATA4

I-SATA2

P1-DIMM1B

(IOH36D-1)

LED5

JWF1

I-SATA1

Watch Dog

Jumper Settings (JWD)

Jumper Setting Defi nition
Pins 1-2 Reset

(default)
Pins 2-3 NMI
Open Disabled

A. Clear CMOS

JPW2

JPW1

CPU1

X8DTH

Rev. 2.0

Intel

5520

DP6

DP7

JPS1

I-SATA0

RAID Key

LSI
SAS2008

JPW3

FAN1

FAN7

JF1

PWR_LED

DP4

FAN2

JOH1

FAN3

Battery

Buzzer

SAS

FLASH

SAS0~3

SAS4~7

FAN4

JL1

B. Watch Dog Enable

JWD

B

SMBus1

JD1

2-28

Chapter 2: Installation

I2C Bus to PCI-Exp. Slots

Use Jumpers JI
the System Management Bus (I

2

C1 and JI2C2 to connect

2

C) to
PCI-Express slots in order to improve
PCI slot performance. These two jump­ers are to be set at the same time. The
default setting is Closed to enable the
connections. See the table on the right
for jumper settings.

VGA Enable

Jumper JPG1 allows you to enable
video connections on the motherboard.
See the table on the right for jumper
settings.

I2C for PCI-E slots

Jumper Settings

Jumper Setting Defi nition
Closed Enabled (Default)
Open Disabled

VGA Enable

Jumper Settings

Jumper Setting Defi nition
1~2 Enabled (Default)
2~3 Disabled

2

A. JI

C1

FAN5

KB/MS

FAN6

USB0/1

IPMI_LAN

COM1

VGA

PHY

LAN1

LAN2

FAN8

JPL1

LAN CTRL

BMC

DP5

TPM

P2-DIMM3A

P2-DIMM3B

P2-DIMM2A

P2-DIMM2B

P2-DIMM1A

P2-DIMM1B

CPU2

Slot7 PCI-E 2.0 X8

Slot6 PCI-E 2.0 X8

Slot5 PCI-E 2.0 X8

A

B

JI2C2

JI2C1

Slot4 PCI-E 2.0 X8

Slot3 PCI-E 2.0 X8

Slot2 PCI-E 2.0 X8

Slot1 PCI-E 2.0 X8

C

COM2

Wake-On-LAN

JHB1

JPG1

JPB

1

1

JWOL1

1

USB6/7

(IOH36D-2)

Intel
ICH10R

(South Bridge)

SATA-SGPIO1

USB3

USB4/5

SATA-SGPIO0

JPI2C

CPU1

P1-DIMM1B

P1-DIMM1A

P1-DIMM2B

P1-DIMM2A

P1-DIMM3B

P1-DIMM3A

Intel

5520

Intel

5520

(IOH36D-1)

JBT1

I-SATA5

I-SATA4

SPI BIOS

I-SATA2

I-SATA3

LED5

SAS Activity

JWF1

I-SATA1

JPW1

DP6
DP7

X8DTH

Rev. 2.0

JPS1

I-SATA0

LSI
SAS2008

RAID Key

JPW2

JPW3

FAN1

FAN7

JF1

PWR_LED

DP4

JWD

FAN2

SMBus1

JOH1

JD1

FAN3

Battery

Buzzer

SAS

FLASH

SAS0~3

SAS4~7

FAN4

JL1

2

B. JI

C2

C. VGA Enable

2-29

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

SAS Enable (X8DTH-6/6F Only)

JPS1 allows you to enable or disable
SAS Connectors. The default position is
on pins 1 an d 2 to e na bl e SA S. S e e th e
table o n the r ight fo r jumper s ett ings.

SAS Enable/Disable

Jumper Settings

Jumper Settings Defi nition
Pins 1-2 Enabled (Default)
Pins 2-3 Disabled

FAN5

KB/MS

FAN6

USB0/1

IPMI_LAN

COM1

VGA

PHY

LAN1

LAN2

FAN8

JPL1

LAN CTRL

BMC

DP5

TPM

P2-DIMM3A

P2-DIMM3B

P2-DIMM2A

P2-DIMM2B

P2-DIMM1A

P2-DIMM1B

CPU2

Slot7 PCI-E 2.0 X8

Slot6 PCI-E 2.0 X8

Slot5 PCI-E 2.0 X8

JI2C2

JI2C1

Slot4 PCI-E 2.0 X8

Slot3 PCI-E 2.0 X8

Slot2 PCI-E 2.0 X8

Slot1 PCI-E 2.0 X8

COM2

Wake-On-LAN

JHB1

JPG1

JPB

1

1

JWOL1

1

USB6/7

(IOH36D-2)

Intel

ICH10R

(South Bridge)

SATA-SGPIO1

USB3

USB4/5

SATA-SGPIO0

JPI2C

CPU1

P1-DIMM1B

P1-DIMM1A

P1-DIMM2B

P1-DIMM2A

P1-DIMM3B

P1-DIMM3A

Intel

5520

Intel

5520

(IOH36D-1)

JBT1

I-SATA5

I-SATA4

SPI BIOS

I-SATA2

I-SATA3

SAS Activity

JWF1

LED5

A

I-SATA1

JPW1

DP6

DP7

X8DTH

Rev. 2.0

JPS1

I-SATA0

RAID Key

LSI
SAS2008

JPW2

JPW3

PWR_LED

Battery

SAS

FLASH

SAS0~3

SAS4~7

FAN4

A. SAS Enable

FAN1

FAN7

JF1

DP4

JWD

FAN2

SMBus1

JOH1

JD1

FAN3

Buzzer

JL1

2-30

Chapter 2: Installation

2-8 Onboard LED Indicators

GLAN LEDs

Two LAN ports (LAN 1/LAN 2) are located
on the IO Backplane of the motherboard.
Each Ethernet LAN port has two LEDs. The
yellow LED indicates activity, while the oth­er Link LED may b e green, a mber or o ff to
indic ate th e sp ee d of th e c on ne ct io ns . Se e
the tab les at ri ght for mo re infor matio n.

IPMI Dedicated LAN LEDs (X8DTH­iF/6F)

In addition to LAN 1/LAN 2, an IPMI Dedi­cated LAN is also located on the IO Back­plane of the X8DTH-iF/6F. The am ber LED
on the right indicates activity, while the
green LED o n the left in dicates the s peed
of the connection. See the tables at right
for more i nform ation.

LAN1/LAN2

Activity LED

Rear View (when facing the

rear side of the chassis)

LAN 1/LAN 2 Activity LED (Right)

Color Status Defi nition
Yellow Flashing Active

LAN 1/LAN 2 Link LED (Left)

LED Color Defi nition
Off No Connection or 10 Mbps
Green 100 Mbps
Amber 1 Gbps

Link LED

IPMI LAN Link LED (Left) &

Color/Status Defi nition
Link (Left) Green: Solid 100 Mbps

Activity
(Right)

LED State

LED State

IPMI LAN (X8DTH-iF/6F only)

Activity LED (Right)

Off
Amber:

Blinking

Link LED

Activity LED

No Connection

Active

A. LAN1/2 LEDs

FAN5

KB/MS

FAN6

B

USB0/1

IPMI_LAN

COM1

VGA

PHY

LAN1

A

LAN2

FAN8

JPL1

LAN CTRL

BMC

DP5

TPM

P2-DIMM3A

P2-DIMM3B

P2-DIMM2A

P2-DIMM2B

P2-DIMM1A

P2-DIMM1B

CPU2

Slot7 PCI-E 2.0 X8

Slot6 PCI-E 2.0 X8

Slot5 PCI-E 2.0 X8

JI2C2

JI2C1

Slot4 PCI-E 2.0 X8

Slot3 PCI-E 2.0 X8

Slot2 PCI-E 2.0 X8

Slot1 PCI-E 2.0 X8

COM2

Wake-On-LAN

JHB1

JPG1

JPB

1

1

JWOL1

1

USB6/7

(IOH36D-2)

Intel
ICH10R

(South Bridge)

SATA-SGPIO1

USB3

USB4/5

SATA-SGPIO0

JPI2C

CPU1

P1-DIMM1B

P1-DIMM1A

P1-DIMM2B

P1-DIMM2A

P1-DIMM3B

P1-DIMM3A

Intel

5520

Intel

5520

(IOH36D-1)

JBT1

I-SATA5

I-SATA4

SPI BIOS

I-SATA2

I-SATA3

LED5

SAS Activity

JWF1

I-SATA1

JPW1

DP6
DP7

X8DTH

Rev. 2.0

JPS1

I-SATA0

LSI
SAS2008

RAID Key

JPW2

JPW3

PWR_LED

Battery

SAS

FLASH

SAS0~3

SAS4~7

FAN4

B. Dedicated LAN LEDs

FAN1

(X8DTH-iF/6F)

FAN7

JF1

DP4

JWD

FAN2

SMBus1

JOH1

JD1

FAN3

Buzzer

JL1

2-31

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

BMC Activity LED (X8DTH-iF/6F)

A BMC He artbe at LED i s lo c ated at D P5
on the motherboard. When DP5 is on,
BMC (Baseboard Management Control­ler) is active. See the table s at right for
more information.

SAS Activity LED (X8DTH-6/6F)

A SAS Act ivity LED is loc ated at LED5.
When LED5 is on, SAS is active. Refer to
the table on the right for details. Also see
the layout b elow fo r the LED l ocat ion.

BMC Activity LED

Indication

Color/Status Defi nition

Green: On BMC is active

SAS Activity LED

Indication

Color/Status Defi nition

Green: On SAS is active

A. BMC Activity LED

FAN5

KB/MS

FAN6

USB0/1

IPMI_LAN

COM1

VGA

PHY

LAN1

LAN2

FAN8

JPL1

LAN CTRL

BMC

A

DP5

TPM

P2-DIMM3A

P2-DIMM3B

P2-DIMM2A

P2-DIMM2B

P2-DIMM1A

P2-DIMM1B

CPU2

Slot7 PCI-E 2.0 X8

Slot6 PCI-E 2.0 X8

Slot5 PCI-E 2.0 X8

JI2C2

JI2C1

Slot4 PCI-E 2.0 X8

Slot3 PCI-E 2.0 X8

Slot2 PCI-E 2.0 X8

Slot1 PCI-E 2.0 X8

COM2

Wake-On-LAN

JHB1

JPG1

JPB

1

1

JWOL1

1

USB6/7

(IOH36D-2)

Intel

ICH10R

(South Bridge)

SATA-SGPIO1

USB3

USB4/5

SATA-SGPIO0

JPI2C

CPU1

P1-DIMM1B

P1-DIMM1A

P1-DIMM2B

P1-DIMM2A

P1-DIMM3B

P1-DIMM3A

Intel

5520

Intel

5520

(IOH36D-1)

JBT1

I-SATA5

I-SATA4

SPI BIOS

I-SATA2

I-SATA3

SAS Activity

JWF1

LED5

I-SATA1

JPW1

DP6

DP7

X8DTH

Rev. 2.0

B

JPS1

I-SATA0

RAID Key

LSI
SAS2008

JPW2

JPW3

FAN1

FAN7

JF1

PWR_LED

DP4

JWD

FAN2

SMBus1

JOH1

FAN3

Battery

Buzzer

SAS

FLASH

SAS0~3

SAS4~7

FAN4

JL1

B. SAS Activity LED

JD1

2-32

Chapter 2: Installation

SAS Heartbeat LED (X8DTH-6/6F)

A SAS Heartb eat L ED is l o c ate d at D P 6.
When DP6 is on, SAS functions normally.
Refer to the t abl e on t he r ig ht for d eta ils .
Also see the layout below for the LED
location.

SAS Error LED (X8DTH-6/6F)

A SAS Activity LED is located at DP7.
When DP 7 is on, an erro r has occur red
with SA S co nn ec ti on s. Refe r to th e ta bl e
on the right for details. Also see the layout
below fo r the LED l oca tion.

SAS Heartbeat LED

Indication

Color/Status Defi nition
Green: On SAS: Normal

SAS Error LED

Indication

Color/Status Defi nition
Red: On

A SAS error occurs

A. SAS Heartbeat LED

FAN5

KB/MS

FAN6

USB0/1

IPMI_LAN

COM1

VGA

PHY

LAN1

LAN2

FAN8

JPL1

LAN CTRL

BMC

DP5

TPM

P2-DIMM3A

P2-DIMM3B

P2-DIMM2A

P2-DIMM2B

P2-DIMM1A

P2-DIMM1B

CPU2

Slot7 PCI-E 2.0 X8

Slot6 PCI-E 2.0 X8

Slot5 PCI-E 2.0 X8

JI2C2

JI2C1

Slot4 PCI-E 2.0 X8

Slot3 PCI-E 2.0 X8

Slot2 PCI-E 2.0 X8

Slot1 PCI-E 2.0 X8

COM2

Wake-On-LAN

JHB1

JPG1

JPB

1

1

JWOL1

1

USB6/7

(IOH36D-2)

Intel
ICH10R

(South Bridge)

SATA-SGPIO1

USB3

USB4/5

SATA-SGPIO0

JPI2C

CPU1

P1-DIMM1B

P1-DIMM1A

P1-DIMM2B

P1-DIMM2A

P1-DIMM3B

P1-DIMM3A

Intel

5520

Intel

5520

(IOH36D-1)

JBT1

I-SATA5

I-SATA4

SPI BIOS

I-SATA2

I-SATA3

LED5

SAS Activity

JWF1

I-SATA1

JPW1

DP6
DP7

X8DTH

Rev. 2.0

A

B

JPS1

I-SATA0

LSI
SAS2008

RAID Key

JPW2

JPW3

FAN1

FAN7

JF1

PWR_LED

DP4

JWD

FAN2

SMBus1

JOH1

FAN3

Battery

Buzzer

SAS

FLASH

SAS0~3

SAS4~7

FAN4

JL1

B. SAS Error LED

JD1

2-33

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

Onboard Power LED

An Onboard Power LED is located at
DP4 on the motherboard. When this
LED is on, the system is on. Be sure
to turn off the system and unplug the
power cord before removing or installing
components. See the tables at right for
more information.

Onboard PWR LED

Indications

LED Color Defi nition
Off System Off (PWR cable

not connected)

Green System Power On

A. Onboard PWR LED

FAN5

KB/MS

FAN6

USB0/1

IPMI_LAN

COM1

VGA

PHY

LAN1

LAN2

FAN8

JPL1

LAN CTRL

BMC

DP5

TPM

P2-DIMM3A

P2-DIMM3B

P2-DIMM2A

P2-DIMM2B

P2-DIMM1A

P2-DIMM1B

CPU2

Slot7 PCI-E 2.0 X8

Slot6 PCI-E 2.0 X8

Slot5 PCI-E 2.0 X8

JI2C2

JI2C1

Slot4 PCI-E 2.0 X8

Slot3 PCI-E 2.0 X8

Slot2 PCI-E 2.0 X8

Slot1 PCI-E 2.0 X8

COM2

Wake-On-LAN

JHB1

JPG1

JPB

1

1

JWOL1

1

USB6/7

(IOH36D-2)

Intel

ICH10R

(South Bridge)

SATA-SGPIO1

USB3

USB4/5

SATA-SGPIO0

JPI2C

CPU1

P1-DIMM1B

P1-DIMM1A

P1-DIMM2B

P1-DIMM2A

P1-DIMM3B

P1-DIMM3A

Intel

5520

Intel

5520

(IOH36D-1)

JBT1

I-SATA5

I-SATA4

SPI BIOS

I-SATA2

I-SATA3

SAS Activity

JWF1

LED5

I-SATA1

JPW1

DP6

DP7

X8DTH

Rev. 2.0

JPS1

I-SATA0

RAID Key

LSI
SAS2008

JPW2

JPW3

FAN1

FAN7

JF1

PWR_LED

DP4

A

JWD

FAN2

SMBus1

JOH1

JD1

FAN3

Battery

Buzzer

SAS

FLASH

SAS0~3

SAS4~7

FAN4

JL1

2-34

Chapter 2: Installation

F

G

2-9 SATA and SAS Connections

Note the following conditions when connecting the Serial ATA and fl oppy disk drive
cables:

• Be sure to use the correct cable for each connector. Refer to Page 1-1 for cables

that came with your shipment.

• A red mark on a wire indicates the location of pin 1.

SATA/SAS Connections (SAS: X8DTH-6/6F)

Six Serial ATA (SATA) connectors (I-SATA 0~5)
are located on the motherboard. In addition to
six SATA ports, eight SAS connections are also
located on the X8DTH-6/6F. These Serial Link
connections provide faster data transmission
than the connections of traditional Parallel ATA.
The SATA connectors are supported by the Intel
ICH10R. The SAS connectors on the X8DTH­6/6F are supported by the LSI SAS 2 controller.
See the table on the right for pin defi nitions.

SATA/SAS Connectors

Pin Defi nitions

Pin# Signal
1 Ground
2 SATA_TXP
3 SATA_TXN
4 Ground
5 SATA_RXN
6 SATA_RXP
7 Ground

Notes: 1. For SATA RAID Confi guration instructions, please refer to the
Intel SATA HostRAID User's Guide posted on our website @ http://www.
supermicro.com/support/manuals/.

2. For instructions on SAS RAID confi guration, please refer to the LSI
MegaRAID User's Guide posted on our website @ http://www.supermicro.
com/support/manuals/.

FAN5

KB/MS

FAN6

USB0/1

IPMI_LAN

COM1

VGA

PHY

LAN1

LAN2

FAN8

JPL1

LAN CTRL

BMC

DP5

TPM

P2-DIMM3A

P2-DIMM3B

P2-DIMM2A

P2-DIMM2B

P2-DIMM1A

P2-DIMM1B

CPU2

Slot7 PCI-E 2.0 X8

Slot6 PCI-E 2.0 X8

Slot5 PCI-E 2.0 X8

JI2C2

JI2C1

Slot4 PCI-E 2.0 X8

Slot3 PCI-E 2.0 X8

Slot2 PCI-E 2.0 X8

Slot1 PCI-E 2.0 X8

COM2

Wake-On-LAN

JHB1

JPG1

JPB

1

1

JWOL1

1

USB6/7

(IOH36D-2)

Intel
ICH10R

(South Bridge)

SATA-SGPIO1

USB3

USB4/5

SATA-SGPIO0

JPI2C

JPW2

JPW1

JPW3

A~F. SATA0~5

FAN1

G. SATA0~3 (X8DTH-6/6F)
H. SATA4~7 (X8DTH-6/6F)

CPU1

P1-DIMM1B

P1-DIMM1A

P1-DIMM2B

P1-DIMM2A

P1-DIMM3B

P1-DIMM3A

X8DTH

(IOH36D-1)

LED5

SAS Activity

JWF1

D

I-SATA1

Rev. 2.0

Intel

5520

DP6

LSI

DP7

SAS2008

JPS1

I-SATA0

RAID Key

C

Intel

5520

JBT1

SPI BIOS

E

I-SATA5

I-SATA3

I-SATA4

I-SATA2

B

A

FAN7

JF1

PWR_LED

DP4

JWD

FAN2

SMBus1

JOH1

JD1

FAN3

Battery

Buzzer

SAS

FLASH

SAS0~3

H

SAS4~7

FAN4

JL1

2-35

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

Notes

2-36

Chapter 3: Troubleshooting

Chapter 3

Troubleshooting

3-1 Troubleshooting Procedures

Use the following procedures to troubleshoot your system. If you have followed all
of the procedures below and still need assistance, refer to the ‘Technical Support
Procedures’ and/or ‘Returning Merchandise for Service’ section(s) in this chapter.
Note: Always disconnect the power cord before adding, changing or installing any
hardware components.

Before Power On

Make sure that there are no short circuits between the motherboard and 1.
chassis.

Disconnect all ribbon/wire cables from the motherboard, including those for 2.
the keyboard and mouse.

Remove all add-on cards.3.

Install CPU 1 fi rst (making sure it is fully seated) and connect the chassis 4.
speaker and the power LED to the motherboard. (Check all jumper settings
as well.)

No Power

Make sure that there are no short circuits between the motherboard and the 1.
chassis.

Make sure that all jumpers are set to their default positions.2.

Check that the 115V/230V switch on the power supply is properly set.3.

Turn the power switch on and off to test the system.4.

The battery on your motherboard may be old. Check to verify that it still sup-5.
plies ~3VDC. If it does not, replace it with a new one.

3-1

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

No Video

If the power is on but you have no video, remove all the add-on cards and 1.
cables.

Use the speaker to determine if any beep codes exist. Refer to the Appendix 2.
for details on beep codes.

Losing the System’s Setup Confi guration

Make sure that you are using a high quality power supply. A poor quality 1.
power supply may cause the system to lose the CMOS setup information.
Refer to Section 1-6 for details on recommended power supplies.

The battery on your motherboard may be old. Check to verify that it still sup-2.
plies ~3VDC. If it does not, replace it with a new one.

If the above steps do not fi x the Setup Confi guration problem, contact your 3.
vendor for repairs.

Memory Errors

When a No_Memory_Beep_Code is issued by the system, check the following:

Make sure that the DIMM modules are properly and fully installed. 1.

Check if different speeds of DIMMs have been installed and check if the BIOS 2.
setup is confi gured for the fastest speed of RAM used. (It is recommended to
use the same RAM speed for all DIMMs in the system.)

Make sure you are using the correct type of Registered ECC or Unbuffered 3.
ECC/Non-ECC DDR3 1333/1066/800 MHz SDRAM (recommended by the
manufacturer.)

Check for bad DIMM modules or slots by swapping a single module between 4.
all memory slots and check the results.

Make sure that all memory modules are fully seated in their slots. Make sure 5.
to follow the instructions given on DIMM population in Section 2-4 in Chapter

2.

Check the position of the 115V/230V switch on the power supply.6.

Please follow the instructions given in the DIMM Population Tables listed on 7.
Pages 2-7 and 2-8 to install your memory modules.

3-2

Chapter 3: Troubleshooting

3-2 Technical Support Procedures

Before contacting Technical Support, please take the following steps. Also, please
note that as a motherboard manufacturer, Supermicro does not sell directly to end­users, so it is best to fi rst check with your distributor or reseller for troubleshooting
services. They should know of any possible problem(s) with the specifi c system
confi guration that was sold to you.

Please go through the ‘Troubleshooting Procedures’ and 'Frequently Asked 1.
Question' (FAQ) sections in this chapter or see the FAQs on our website
(

http://www.supermicro.com/support/faqs/) before contacting Technical Sup-

port.

BIOS upgrades can be downloaded from our website at 2.

cro.com/support/bios/

If you still cannot resolve the problem, include the following information when 3.
contacting Supermicro for technical support:

Motherboard model and PCB revision number

•

BIOS release date/version (this can be seen on the initial display when your •
system fi rst boots up)

System confi guration

•

An example of a Technical Support form is on our website at • (http://www.super-

micro.com/support/contact.cfm).

Distributors: For immediate assistance, please have your account number ready

•

when placing a call to our technical support department. We can be reached by
e-mail at [e-mail] or by fax at: [phone], option 2.

).

(http://www.supermi-

3-3 Frequently Asked Questions

Que sti on: Wh at a re th e var iou s t ype s of m emo r y th at my mo th er boa rd c an
support?

Answer: The X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF has 12 240-pin DIMM slots

that support up to 96 GB of Reg. ECC or up to 24 GB of Unbuffered ECC/Non-ECC
DDR3 1333/1066/800 MHz SDRAM modules. It is strongly recommended that you
do not mix memory modules of different speeds and sizes. Please follow all memory
installation instructions given on Section 2-4 in Chapter 2.

3-3

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

Que stio n: How do I u pda te my BI OS?
Answer: It is recommended that you do not upgrade your BIOS if you are not

experiencing any problems with your system. Updated BIOS fi les are located on
our web site at
warning message and the information on how to update your BIOS on our web
site. Select your motherboard model and download the BIOS fi le to your computer.
Also, check the current BIOS revision and make sure that it is newer than your
BIOS before downloading. You can choose from the zip fi le and the .exe fi le. If you
choose the zip BIOS fi le, please unzip the BIOS fi le onto a bootable USB device.
Run the batch fi le using the format fl ash.bat fi lename.rom from your bootable USB
device to fl ash the BIOS. Then, your system will automatically reboot. Please note
that this process may take a few minutes to complete. Do not be concerned if the
screen is paused for a few minutes.

http://www.supermicro.com/support/bios/. Please check our BIOS

Warning: Do not shut down or reset the system while updating the BIOS

to prevent possible system boot failure!

Note 1: The SPI BIOS chip used on this motherboard cannot be removed.

Send your motherboard back to our RMA Department for repair.

Note 2: For BIOS Recovery instructions, please refer to the AMI BIOS

Recovery Instruction Guide posted at http://www.supermicro.com/support/
manuals/.

Question: What's on the CD that came with my motherboard?
Answer: The supplied CD has drivers and programs that are needed for your sys-

tem. Please r eview t h e C D and i ns t al l th e ap pl ication s you n ee d. A p pl ication s on
the CD inc lude c hipset d river s for th e Wind ows OS, se cur ity an d audio dr iver s.

3-4 Returning Merchandise for Service

A receipt or copy of your invoice marked with the date of purchase is required be­fore any warranty service will be rendered. You can obtain service by calling your
vendor for a Returned Merchandise Authorization (RMA) number. When returning to
the manufacturer, the RMA number should be prominently displayed on the outside
of the shipping carton, and mailed prepaid or hand-carried. Shipping and handling
charges will be applied for all orders that must be mailed when service is complete.
For faster service, You can also request a RMA authorization online (http://www.
supermicro.com/support/rma/).

This warranty only covers normal consumer use and does not cover damages in­curred in shipping or from failure due to the alternation, misuse, abuse or improper
maintenance of products.

During the warranty period, contact your distributor fi rst for any product problems.

3-4

Chapter 4: AMI BIOS

Chapter 4

BIOS

4-1 Introduction

This chapter describes the AMI BIOS Setup Utility for the X8DTH-6/X8DTH-6F/
X8DTH-i/X8DTH-iF. The AMI ROM BIOS is stored in a Flash EEPROM and can be
easily updated. This chapter describes the basic navigation of the AMI BIOS Setup
Utility setup screens.

Note: For BIOS recovery, please refer to the AMI BIOS Recovery Instruc-

tion Guide posted at http://www.supermicro.com/support/manuals/.

Starting BIOS Setup Utility

To enter the AMI BIOS Setup Utility screens, press the <Delete> key while the
system is booting up.

Note: In most cases, the <Delete> key is used to invoke the AMI BIOS
setup screen. There are a few cases when other keys are used, such as
<F1>, <F2>, etc.

Each main BIOS menu option is described in this manual. The Main BIOS setup
menu screen has two main frames. The left frame displays all the options that can
be confi gured. Grayed-out options cannot be confi gured. Options in blue can be
confi gured by the user. The right frame displays the key legend. Above the key
legend is an area reserved for a text message. When an option is selected in the
left frame, it is highlighted in white. Often a text message will accompany it. (Note:
the AMI BIOS has default text messages built in. Supermicro retains the option to
include, omit, or change any of these text messages.)

The AMI BIOS Setup Utility uses a key-based navigation system called "hot keys."
Most of the AMI BIOS setup utility "hot keys" can be used at any time during the
setup navigation process. These keys include <F1>, <F10>, <Enter>, <ESC>, ar­row keys, etc.

Note: Options printed in Bold are default settings.

How To Change the Confi guration Data

The confi guration data that determines the system parameters may be changed by
entering the AMI BIOS Setup utility. This Setup utility can be accessed by pressing
<Del> at the appropriate time during system boot.

4-1

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

Starting the Setup Utility

Normally, the only visible Power-On Self-Test (POST) routine is the memory test.
As the memory is being tested, press the <Delete> key to enter the main menu of
the AMI BIOS Setup Utility. From the main menu, you can access the other setup
screens. An AMI BIOS identifi cation string is displayed at the bottom left corner of
the screen below the copyright message.

Warning! Do not upgrade the BIOS unless your system has a BIOS-related
issue. Flashing the wrong BIOS can cause irreparable damage to the
system. In no event shall Supermicro be liable for direct, indirect, special,
incidental, or consequential damages arising from a BIOS update. If you
have to update the BIOS, do not shut down or reset the system while the
BIOS is updating. This is to avoid possible boot failure.

4-2 Main Setup

When you fi rst enter the AMI BIOS Setup Utility , you will enter the Main setup screen.
You can always return to the Main setup screen by selecting the Main tab on the
top of the screen. The Main BIOS Setup screen is shown below.

System Overview: The following BIOS information will be displayed:

System Time/System Date

Use this option to change the system time and date. Highlight System Time or
System Date using the arrow keys. Key in new values through the keyboard and

press <Enter>. Press <Tab> to move between fi elds. The date must be entered in
MM/DD/YY format. The time is entered in HH:MM:SS format. (Note: The time is in
the 24-hour format. For example, 5:30 P.M. appears as 17:30:00.)

4-2

Chapter 4: AMI BIOS

Supermicro X8DTH

Version

• : This item displays the BIOS revision used in your system.

Build Date

• : This item displays the date when this BIOS was completed.

Processor

The AMI BIOS will automatically display the status of the processor used in your
system:

CPU Type

• : This item displays the type of CPU used in the motherboard.

Speed

• : This item displays the speed of the CPU detected by the BIOS.

Physical Count

• : This item displays the number of processors installed in your

system as detected by the BIOS.

Logical Count

• : This item displays the number of CPU Cores installed in your

system as detected by the BIOS.

System Memory

This displays the size of memory available in the system.

4-3

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

4-3 Advanced Setup Confi gurations

Use the arrow keys to select Advanced Setup and press <Enter> to access the
submenu items:

Boot Features

Quick Boot

If Enabled, this option will skip certain tests during POST to reduce the time needed
for system boot. The options are Enabled and Disabled.

Quiet Boot

This option allows the bootup screen options to be modifi ed between POST mes-
sages or the OEM logo. Select Disabled to display the POST messages. Select
Enabled to display the OEM logo instead of the normal POST messages. The op­tions are Enabled and Disabled.

AddOn ROM Display Mode

This sets the display mode for the Option ROM. The options are Force BIOS and
Keep Current.

Bootup Num-Lock

This featu re sel ect s the Powe r-on st ate for t he Num loc k key. The options ar e Of f
and On.

PS/2 Mouse Su ppor t

This feature enables support for the PS/2 mouse. The options are Disabled,
Enabled and Auto.

4-4

Chapter 4: AMI BIOS

Wait For 'F1' If Error

This forces the system to wait until the <F1> key is pressed if an error occurs. The
option s are Dis able d and Enabled.

Hit 'Del' Message Display

This feat ure displays the " Press DEL to r un Setup" mess age during PO ST. The
options are Enabled and Disabled.

Watch Dog Function

If enabl ed, t he Watch D o g Tim er w ill a ll ow th e syste m to re bo ot whe n it i s not ac­tive for m ore tha n 5 minutes. T he opti ons are En abled a nd Disabled.

Power Button Function

If this option is set to Instant_Off, the system will power off immediately as soon
as the user presses the power button. If this option is set to 4_Second_Override,
the system will power off when the user presses the power button for 4 seconds or
longer. The options are Instant_Off and 4_Second_Override.

Restore on AC Power Loss

Use this feature to set the power state after a power outage. Select Power-Off for
the system power to remain off after a power loss. Select Power-On for the system
power to be turned on after a power loss. Select Last State to allow the system to
resume its last state before a power loss. The options are Power-On, Power-Off
and Last State.

Interrupt 19 Capture

Interrupt 19 is the software interrupt that handles the boot disk function. When this
item is set to Enabled, the ROM BIOS of a host adaptor will "capture" Interrupt 19
at bootup and allow the drives that are attached to the host adaptor to function as
a bootable disk. If this item is set to Disabled, the ROM BIOS of the host adaptor
will not capture Interrupt 19, and the drives attached to the adaptor will not function
as a bootable device. The options are Enabled and Disabled.

Processor and Clock Options

This submenu allows the user to confi gure the Processor and Clock settings.

4-5

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

CPU Ratio

If set to Manual, this option allows the user to set the ratio between the CPU Core
Clock and the FSB Frequency. (Note: if an invalid ratio is entered, the AMI BIOS
will restore the setting to the previous state.) The options are Auto and Manual.

Clock Spread Spectrum

Select Enable to enable Clock Spectrum support, which will allow the BIOS to moni­tor and attempt to reduce the level of Electromagnetic Interference caused by the
components whenever needed. The options are Disabled and Enabled.

Hardware Prefetcher (Available when supported by the CPU)

If this item is set to Enabled, the hardware prefetcher will prefetch streams of data
and instructions from the main memory to the L2 cache in the forward or backward
manner to improve CPU performance. The options are Disabled and Enabled.

Adjacent Cache Line Prefetch (Available when supported by the CPU)

The CPU fetches the cache line for 64 bytes if this option is set to Disabled. The
CPU fetches both cache lines for 128 bytes as comprised if this option is set to

Enabled.

MPS and ACPI MADT Ordering

This feature allows the user to decide how to order the Multiple APIC Description
Table (MADT). Select Modern Ordering for the Microsoft Windows XP or a later
version of OS. Select Legacy Ordering for the Microsoft Windows XP or an earlier
version of OS. The options are Modern Ordering and Legacy Ordering.

4-6

Chapter 4: AMI BIOS

Machine Checking (Available when supported by the CPU.)

Set to Enabled to activate the function of Machine Checking and allow the CPU to
detect and report hardware (machine) errors via a set of model-specifi c registers
(MSRs). The options are Disabled and Enabled.

Intel® Virtualization Technology (Available when supported by the CPU)

Selec t Enabled to u se the Vir tua lizatio n Techno logy to al low one plat for m to run
multiple operating systems and applications in independent partitions, creating
multiple "virtual" systems in one physical com puter. The optio n s are Enabled and
Disabled. Note: If ther e is any change to t his sett ing, you will ne ed to power of f
and rest art the syst em for the chang e to take effec t. Please refer to I ntel’s web
site for detailed information.

Execute-Disable Bit Capability (Available when supported by the OS and
the CPU)

Set to Enabled to enable Execute Disable Bit support which will allow the processor
to designate areas in the system memory where an application code can execute
and where it cannot, thus preventing a worm or a virus from fl ooding illegal codes
to overwhelm the processor or damage the system during an attack. The default is

Enabled. (Refer to Intel and Microsoft Web Sites for more information.)

Simultaneous Multi-Threading (Available when supported by the CPU)

Set to Enabled to use the Simultaneous Multi-Threading Technology, which will
increase CPU performance. The options are Disabled and Enabled.

Active Processor Cores

Set to Enabled to use a processor's Second Core and beyond. (Please refer to
Intel's web site for more information.) The options are All, 1 and 2.

Intel® EIST Technology

EIST (Enhanced Intel SpeedStep Technology) allows the system to automatically
adjust processor voltage and core frequency in an effort to reduce power consump­tion and heat dissipation. Please refer to Intel’s web site for detailed information.
The options are Disabled and Enabled.

Intel® TurboMode Tech

Select Enabled to use the Turbo Mode to boost system performance. The options
are Enabled and Disabled.

C1E Support

Select Enabled to use the feature of Enhanced Halt State. C1E signifi cantly reduces
the CPU's power consumption by reducing the CPU's clock cycle and voltage during
a "Halt State." The options are Disabled and Enabled.

4-7

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

Intel® C-STATE Tech

If enabled, C-State is set by the system automatically to either C2, C3 or C4 state.
The options are Disabled and Enabled.

C-State package Limit Setting (Available when C-State support is enabled)

If set to Auto, the AMI BIOS will automatically set the limit on the C-State package
register. The options are Auto, C1, C3, C6 and C7.

C1 Auto Demotion

When this item is set to enabled, the CPU will conditionally demote C3, C6 or C7
requests to C1 based on un-core auto-demote information. The options are Disabled
and Enabled.

C3 Auto Demotion

When this item is set to enabled, the CPU will conditionally demote C6 or C7 re­quests to C3 based on un-core auto-demote information. The options are Disabled
and Enabled.

ACPI T State

Select Enabled to report Processor throttling in the ACPI. The options are Disabled
and Enabled.

Advanced Chipset Control

CPU Bridge Confi guration

QPI Links Speed

Use this item to select QPI data transfer speeds and enable/disable QPI Fre­quency selection. If Slow-mode is selected, QPI Frequency will remain slow (safe
mode), and cannot be selected the user. If Full-speed is selected, the following
item will be available for the user to select the QPI frequency. The options are
Slow-mode, and Full-Speed.

QPI Frequency (Available when QPI Links Speed is set to Full-speed)

This selects the desired QPI frequency. The options are Auto, 4.800 GT,

5.866GT, 6.400 GT.

QPI L0s and L1

Select Enabled to lower power consumption during the QPI power state. L0s
and L1 are automatically selected by the motherboard. The options are Disabled
and Enabled.

4-8

Chapter 4: AMI BIOS

Memory Frequency

This feature forces a DDR3 to run at a frequency other than what the system has
detected. Select Force SPD (Serial Presence Detect) to force the memory to run
at a frequency based on the SPD Standard (Table). The available options are

Auto, Force DDR-800, Force DDR-1066, Force DDR-1333, and Force SPD.

Memory Mode

The options are Independent, Channel Mirror, and Lockstep.
Independent - All DIMMs are available to the operating system.
Channel Mirror - The motherboard maintains two identical copies of all data in

memory for redundancy.
Lockstep - The motherboard uses two areas of memory to run the same set of

operations in parallel.

Demand Scrubbing

A memory error-correction scheme that allows the processor to write correct
data back into the memory block from where it was read by the processor. The
options are Enabled and Disabled.

Patrol Scrubbing

A memory error-correction scheme that works in the background looking for and
correcting resident errors. The options are Enabled and Disabled.

Channel Interleave

This feature allows the user to confi gure the Memory Interleave setting for an
onboard memory channel. The options are 1-way, 2-way, 3-way, 4-way, and

6-way.

Bank Interleave

This feature allows the user to confi gure the Memory Interleave setting for an
onboard memory bank. The options are 1-way, 2-way, and 4-way.

Throttling - Closed Loop

Throttling improves reliability and reduces power consumption in the proces­sor via automatic voltage control during processor idle states. The options are
Disabled and Enabled.

4-9

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

North Bridge Confi guration

Intel I/OAT

The Intel I/OAT (I/O Acceleration Technology) signifi cantly reduces CPU over-
head by leveraging CPU architectural improvements, freeing the system resource
for other tasks. The options are Disabled and Enabled.

DCA Technology

Select Enabled to use Intel's DCA (Direct Cache Access) Technology to improve
data transfer effi ciency. The options are Enabled and Disabled.

DCA Prefetch Delay

A DCA Prefetch is used with TOE components to prefetch data in order to shorten
execution cycles and maximize data processing effi ciency. A TOE device is a
specialized, dedicated processor that is installed on an add-on card or a network
card to handle some or all packet processing of this add-on card. Prefetching
too frequently can saturate the cache directory and delay necessary cache ac­cesses. This feature reduces or increases the frequency the system prefetches
data. The options are [8], [16], [32], [40], [48], [56], [64], [72], [80], [88], [96],
[104], [112], and [120].

Intel VT-d

Select Enabled to enable Intel Virtualization Technology support for Direct I/O
VT-d

by reporting the I/O device assignments to the VMM (Virtual Working

Memory) through the DMAR ACPI Tables. This feature offers fully-protected
I/O resource sharing across Intel platforms, providing greater reliability, security
and availability in networking and data-sharing. The options are Enabled and

Disabled.

Active State Power-Management

Selec t Enab le d to use t he p ower m anag em ent fo r sig nal t ra nsac tions between
the PCI Express L0 and L1 Links. Select Enabled to confi gure PCI-Exp. L0 and
L1 Link power states. The options are Disabled and Enabled.

IOH PCI-E Max Payload Size

Some add-on cards perform faster with the coalesce feature, which limits the
payload size to 128B; while others, with a payload size of 256B which inhibits
the coalesce feature. Please refer to your add-on card user guide for the desired
setting. The options are 256B and 128B.

4-10

Chapter 4: AMI BIOS

South Bridge Confi guration

USB Functions

This feature allows the user to decide the number of onboard USB ports to be
enabled. The Options are: Disabled, 2 USB ports, 4 USB ports, 6 USB ports, 8
USB ports, 10 USB ports and 12 USB ports.

USB 2.0 Controller (Available when the item: USB Functions is disabled)

This feature displays the current USB controller used in the motherboard.

Legacy USB Support

Select Enabled to use Legacy USB devices. If this item is set to Auto, Legacy
USB support will be automatically enabled if a legacy USB device is installed on
the motherboard. The settings are Disabled, Enabled and Auto.

Port60h/64h Emulation

Select Enabled to enable 60h/64h emulation for complete USB keyboard support
for operating systems that are not compatible with USB devices. The options
are Enabled and Disabled.

IDE/SATA Confi guration

When this submenu is selected, the AMI BIOS automatically detects the presence
of the IDE devices and displays the following items.

SATA#1 Confi guration

If Compatible is selected, it sets SATA#1 to legacy compatibility mode. Selecting
Enhanced sets SATA#1 to native SATA mode. The options are Disabled, Compat­ible and Enhanced.

Confi gure SATA#1 as

This feature allows the user to select the drive type for SATA#1. The options are
IDE, RAID and AHCI. (When the option-RAID is selected, the item-ICH RAID
Code Base will appear.)

ICH RAID Code Base (Available when the option-RAID is selected)

Select Intel to enable Intel's SATA RAID fi rmware to confi gure Intel's SATA RAID
settings. Select Adaptec to enable Adaptec's SATA RAID fi rmware to confi gure
Adaptec's SATA RAID settings. The options are Intel and Adaptec.

4-11

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

SATA#2 Confi guration (This feature is available when the option-IDE is
selected for SATA#1)

Selecting Enhanced will set SA T A#2 to native SA TA mode. The options are Disabled,
and Enhanced.

IDE Detect Timeout (sec)

Use this feature to set the time-out value for the BIOS to detect the ATA, ATAPI
devices installed in the system. The options are 0 (sec), 5, 10, 15, 20, 25, 30, and

35.

Primary IDE Master/Slave, Secondary IDE Master/Slave, Third IDE Master,
and Fourth IDE Master

These settings allow the user to set the parameters of the slots indicated above.
Press <Enter> to activate the following submenu screen items. Set the correct
confi gurations accordingly.

Type

Select the type of a device connected to the system. The options are Not In­stalled, Auto, CD/DVD and ARMD.

LBA/Large Mode

LBA (Logical Block Addressing) is a method of addressing data on a disk drive.
In the LBA mode, the maximum drive capacity is 137 GB. For drive capacities
over 137 GB, your system must be equipped with a 48-bit LBA mode addressing.
If not, contact your manufacturer or install an ATA/133 IDE controller card that
supports 48-bit LBA mode. The options are Disabled and Auto.

Block (Multi-Sector Transfer)

Block Mode boosts the IDE drive performance by increasing the amount of data
transferred. Only 512 bytes of data can be transferred per interrupt if Block Mode
is not used. Block Mode allows transfers of up to 64 KB per interrupt. Select
Disabled to allow data to be transferred to and from devices one sector at a time.
Select Auto to allow data transfer to and from the devices occur multiple sectors
at a time if the devices supports it. The options are Auto and Disabled.

PIO Mode

The IDE PIO (Programmable I/O) Mode programs timing cycles between the
IDE drive and the programmable IDE controller. As the PIO mode increases, the
cycle time decreases. The options are Auto, 0, 1, 2, 3, and 4.

Select Auto to allow the AMI BIOS to automatically detect the PIO mode. Use
this value if the IDE disk drive support cannot be determined.

Select 0 to allow the AMI BIOS to use PIO mode 0. It has a data transfer rate
of 3.3 MB/s.

4-12

Chapter 4: AMI BIOS

Select 1 to allow the AMI BIOS to use PIO mode 1. It has a data transfer rate
of 5.2 MB/s.

Select 2 to allow the AMI BIOS to use PIO mode 2. It has a data transfer rate
of 8.3 MB/s.

Select 3 to allow the AMI BIOS to use PIO mode 3. It has a data transfer rate
of 11.1 MB/s.

Select 4 to allow the AMI BIOS to use PIO mode 4. It has a data transfer band­width of 32-Bits. Select Enabled to enable 32-Bit data transfer.

DMA Mode

Select Auto to allow the BIOS to automatically detect IDE DMA mode when the
IDE disk drive support cannot be determined.

Select SWDMA0 to allow the BIOS to use Single Word DMA mode 0. It has a
data transfer rate of 2.1 MB/s.

Select SWDMA1 to allow the BIOS to use Single Word DMA mode 1. It has a
data transfer rate of 4.2 MB/s.

Select SWDMA2 to allow the BIOS to use Single Word DMA mode 2. It has a
data transfer rate of 8.3 MB/s.

Select MWDMA0 to allow the BIOS to use Multi Word DMA mode 0. It has a
data transfer rate of 4.2 MB/s.

Select MWDMA1 to allow the BIOS to use Multi Word DMA mode 1. It has a
data transfer rate of 13.3 MB/s.

Select MWDMA2 to allow the BIOS to use Multi-Word DMA mode 2. It has a
data transfer rate of 16.6 MB/s.

Select UDMA0 to allow the BIOS to use Ultra DMA mode 0. It has a data transfer
rate of 16.6 MB/s. It has the same transfer rate as PIO mode 4 and Multi Word
DMA mode 2.

Select UDMA1 to allow the BIOS to use Ultra DMA mode 1. It has a data transfer
rate of 25 MB/s.

Select UDMA2 to allow the BIOS to use Ultra DMA mode 2. It has a data transfer
rate of 33.3 MB/s.

Select UDMA3 to allow the BIOS to use Ultra DMA mode 3. It has a data transfer
rate of 66.6 MB/s.

Select UDMA4 to allow the BIOS to use Ultra DMA mode 4. It has a data transfer
rate of 100 MB/s.

Select UDMA5 to allow the BIOS to use Ultra DMA mode 5. It has a data transfer
rate of 133 MB/s.

4-13

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

Select UDMA6 to allow the BIOS to use Ultra DMA mode 6. It has a data transfer
rate of 133 MB/s. The options are Auto, SWDMAn, MWDMAn, and UDMAn.

S.M.A.R.T. For Hard disk drives

Self-Monitoring Analysis and Reporting Technology (SMART) can help predict
impending drive failures. Select Auto to allow the AMI BIOS to automatically de­tect hard disk drive support. Select Disabled to prevent the AMI BIOS from using
the S.M.A.R.T. Select Enabled to allow the AMI BIOS to use the S.M.A.R.T. to
support hard drive disk. The options are Disabled, Enabled, and Auto.

32Bit Data Transfer

Select Enable to enable the function of 32-bit IDE data transfer. The options are
Enabled and Disabled.

PCI/PnP Confi guration

Clear NVRAM

This feature clears NVRAM (Non-Volatile Memory used for Flash ROM) at bootup.
The options are No and Yes.

Plug & Play OS

Selecting Yes allows the OS to confi gure Plug & Play devices. (This is not required
for system boot if your system has an OS that supports Plug & Play.) Select No to
allow the AMI BIOS to confi gure all devices in the system.

PCI Latency Timer

This feature sets the latency timer of each PCI device installed on a PCI bus. Select
64 to set the PCI latency to 64 PCI clock cycles. The options are 32, 64, 96, 128,
160, 192, 224 and 248.

PCI IDE BusMaster

When this item is enabled, the AMI BIOS uses PCI bus mastering for reading and
writing to IDE drives. The options are Disabled and Enabled.

PCI-E Slots 1~7 x8

This feature allows the user to Enable or Disable any of the PCI slots. The
options are Enable and Disable.

Onboard LAN Option ROM Select

This feature allows the user to select the onboard LAN option ROM type. The op­tions are iSCSI and PXE.

4-14

Chapter 4: AMI BIOS

Load Onboard LAN1 Option ROM/Load Onboard LAN2 Option ROM

Selec t Enabled to en able the onboard LAN1 or LAN2 Option ROM. This is to boot
computer using a network interface. The options are Enabled and Disabled.

Load Onboard SAS Option ROM

Selec t En ab l e d to e na b le t h e o nb o ar d S A S O pt i o n RO M . T his is to boot computer
using a network interface. The options are Enabled and Disabled.

Boot Graphics Adapter Priority

This feature allows the user to specify which graphics controller to be used as
the pri mar y boot grap hics c ontroll er. The options are Onboard VGA, PCI- E Slot
7, and O ther.

Super IO Device Confi guration

Serial Port1 Address/ Serial Port2 Address

This option specifi es the base I/O port address and the Interrupt Request address
of Serial Port 1 and Serial Port 2. Select Disabled to prevent the serial port from
accessing any system resources. When this option is set to Disabled, the serial port
physically becomes unavailable. Select 3F8/IRQ4 to allow the serial port to use 3F8
as its I/O port address and IRQ 4 for the interrupt address. The options for Serial
Port1 are Disabled, 3F8/IRQ4, 3E8/IRQ4, 2E8/IRQ3. The options for Serial Port2
are Disabled, 2F8/IRQ3, 3E8/IRQ4, and 2E8/IRQ3.

Serial Port 2 Attribute

This feature allows the user to set COM 2 as a normal serial port or a virtual COM
por t used f or SOL (Ser ial O ver L AN). The options are SOL, an d COM .

Remote Access Confi guration

Remote Access

This allows the user to enable the Remote Access feature. The options are Disabled
and Enabled.

If Remote Access is set to Enabled, the following items will display:

Serial Port Number

This feature allows the user decide which serial port to be used for Console Redi­rection. The options are COM 1 and COM 2.

4-15

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

Base Address, IRQ

This item displays the based address and IRQ of the serial port specifi ed above.
The default setting for COM1 is 3F8/IRQ4, and for COM 2 is 2F8/IRQ3.

Serial Port Mode

This feature allows the user to set the serial port mode for Console Redirection.
The options are 115200 8, n 1; 57600 8, n, 1; 38400 8, n, 1; 19200 8, n, 1; and
9600 8, n, 1.

Flow Control

This feature allows the user to set the fl ow control for Console Redirection. The
options are None, Hardware, and Software.

Redirection After BIOS POST

Selec t Disabl ed to turn off Co n sole Redirecti on after Po we r-On Se l f-Test ( P OST).
Selec t Always to kee p Cons ole Re direc tio n acti ve all the t ime af ter P OST. (Note:
This setting may not be supported by some operating systems.) Select Boot Loader
to keep Con sole Redirec tion active du ring POST and B oot Loader. The option s
are Disa bled, B oot Loade r, and Always.

Terminal Type

This feature allows the user to select the target terminal type for Console Redirec­tion. The options are ANSI, VT100, and VT-UTF8.

VT-UTF8 Combo Key Support

A terminal keyboard defi nition that provides a way to send commands from a remote
console. Available options are Enabled and Disabled.

Sredir Memory Display Delay

This feature defi nes the length of time in seconds to display memory information.
The options are No Delay, Delay 1 Sec, Delay 2 Sec, and Delay 4 Sec.

Hardware Health Monitor

This feature allows the user to monitor system health and review the status of each
item as displayed.

CPU Overheat Alarm

This option allows the user to select the CPU Overheat Alarm setting which de­termines when the CPU OH alarm will be activated to provide warning of possible
CPU overheat.

Warning! 1.Any temperature that exceeds the CPU threshold tempera­ture predefi ned by the CPU manufacturer may result in CPU overheat or

4-16

Chapter 4: AMI BIOS

system instability. When the CPU temperature reaches this predefi ned
threshold, the CPU and system cooling fans will run at full speed. 2. To
avoid possible system overheating, please be sure to provide adequate
airfl ow to your system.

The options are:

The Early Alarm: Select this setting if you want the CPU overheat alarm (includ-

•

ing the LED and the buzzer) to be triggered as soon as the CPU temperature
reaches the CPU overheat threshold as predefi ned by the CPU manufacturer.

The Default Alarm

• : Select this setting if you want the CPU overheat alarm

(including the LED and the buzzer) to be triggered when the CPU temperature
reaches about 5
manufacturer to give the CPU and system fans additional time needed for CPU
and system cooling. In both the alarms above, please take immediate action
as shown below.

o

C above the threshold temperature as predefi ned by the CPU

CPU 1 Temperature/CPU 2 Temperature/System Temperature

This feature displays current temperature readings for the CPUs and the System.
The following items will be displayed for your reference only:

CPU 1 Temperature/ CPU 2 Temperature

The CPU Temperature feature will display the CPU temperature status as detected
by the BIOS:

Low – This level is considered as the ‘normal’ operating state. The CPU temperature
is well below the CPU ‘Temperature Tolerance’. The motherboard fans and CPU will
run normally as confi gured in the BIOS (Fan Speed Control).

Medium – The processor is running warmer. This is a ‘precautionary’ level and
generally means that there may be factors contributing to this condition, but the CPU
is still within its normal operating state and below the CPU ‘Temperature Tolerance’.
The motherboard fans and CPU will run normally as confi gured in the BIOS. The
fans may adjust to a faster speed depending on the Fan Speed Control settings.

High – The processor is running hot. This is a ‘caution’ level since the CPU’s ‘Tem­perature Tolerance’ has been reached (or has been exceeded) and may activate
an overheat alarm. The system may shut down if it continues for a long period to
prevent damage to the CPU.

User intervention: If the system buzzer and Overheat LED has activated, take action
immediately by checking the system fans, chassis ventilation and room temperature
to correct any problems.

4-17

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

Notes:

1. The CPU thermal technology that reports absolute temperatures (Celsius/
Fahrenheit) has been upgraded to a more advanced feature by Intel in its newer
processors. The basic concept is each CPU is embedded by unique temperature
information that the motherboard can read. This ‘Temperature Threshold’ or
‘Temperature Tolerance’ has been assigned at the factory and is the baseline on
which the motherboard takes action during different CPU temperature conditions.
Since CPUs can have different ‘Temperature Tolerances’, the installed CPU can
now send information to the motherboard what its ‘T emperature Tolerance’ is, and
not the other way around. This results in better CPU thermal management.

Supermicro has leveraged this feature by assigning a temperature status to
certain thermal conditions in the processor (Low, Medium and High). This makes
it easier for the user to understand the CPU’s temperature status, rather than by
just simply seeing a temperature reading (i.e., 25

o

C).

The information provided above is for your reference only. For more information
on thermal management, please refer to Intel’s Web site at www.Intel.com.

2. To avoid possible overheating, be sure to provide adequate airfl ow to the
system.

System Temperature: The system te mperat ure will b e displayed ( in degre es in
Celsiu s and Fahrenh eit) as it is detec ted by the BI OS.

Fan Speed Readings

This feature displays the fan speed readings from Fan1 through Fan8.

Fan Speed Control Modes

This feature allows the user to decide how the system controls the speeds of the
onboard fans. The CPU temperature and the fan speed are correlative. When the
CPU on-die temperature increases, the fan speed will also increase for effective
system cooling. Select "Full Speed/FS" to allow the onboard fans to run at full
speed for maximum cooling. The FS setting is recommended for special system
confi guration or debugging. Select "Performance/PF" for better system cooling. The
PF setting is recommended for high-power-consuming and high-density systems.
Select "Balanced/BL" for the onboard fans to run at a speed that will balance the
needs between system cooling and power saving. The BL setting is recommended
for regular systems with normal hardware confi gurations. Select "Energy Saving/ES"
for best power effi ciency and maximum quietness. The Options are: Full Speed/FS,
Performance/PF, Balanced/BL, and Energy Saving/ES.

Voltage Readings

The following voltage readings will be displayed.

4-18

Chapter 4: AMI BIOS

CPU1 Vcore, CPU2 Vcore, CPU1 Vtt, CPU2 Vtt, CPU1 DIMM, CPU2 DIMM, 1.1V,

1.5V, 1.8V, 3.3V, 12V, 5V, 3.3 Vsb, and VBAT

ACPI Confi guration

Use this feature to confi gure Advanced Confi guration and Power Interface (ACPI)
power management settings for your system.

ACPI Aware O/S

Select Yes to enable ACPI support if it is supported by the OS to control ACPI
through the Operating System. Otherwise, disable this feature. The options are

Yes and No.

ACPI Version Features

The options are ACPI v1.0, ACPI v2.0 and ACPI v3.0. Please refer to ACPI's website
for further explanation: http://www.acpi.info/.

ACPI APIC Support

Select Enabled to include the ACPI APIC Table Pointer in the RSDT (Root System
Description Table) pointer list. The options are Enabled and Disabled.

APIC ACPI SCI IRQ

When this item is set to Enabled, APIC ACPI SCI IRQ is supported by the system.
The options are Enabled and Disabled.

Headless Mode

This feature is used to enable system to function without a keyboard, monitor and/
or mouse attached The options are Enabled and Disabled.

High Performance Event Timer

Select Enabled to activate the High Performance Event Timer (HPET) that produces
periodic interrupts at a much higher frequency than a Real-time Clock (RTC) does in
synchronizing multimedia streams, providing smooth playback and reducing the de­pendency on other timestamp calculation devices, such as an x86 RDTSC Instruc­tion embedded in the CPU. The High Performance Event Timer is used to replace
the 8254 Programmable Interval Timer. The options are Enabled and Disabled.

NUMA Support

Select Enabled to enable Non-Uniform Memory Access support for an "NUMA­Aware" OS to improve CPU performance. Select Disabled to provide better memory
access for an "non-NUMA" OS. Select NUMA for SLES 11 for better CPU perfor­mance on a SUSE Linux Enterprise Server 11. The options are Enabled, Disabled
and NUMA for SLES11.

4-19

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

WHEA Support

Select Enabled to enable Windows Hardware Error Architecture (WHEA) support
which will provide a common infrastructure for the system to handle hardware
error s on W indow s plat for ms in o rde r to redu ce syste m cra shes d ue to har dware
erro rs and to enhanc e system recover y and health m onitoring. T he default set­ting is Enabled.

Trusted Computing (Available when a TPM device is
detected)

TCG/TPM (Trusted Platform Module) Support

Select Yes on this item and enable the TPM jumper on the motherboard to enable
TCG (TPM 1.1/1.2)/TPM support in order to improve data integrity and network
security. The options are No and Yes. If this feature is set to Yes, the following

items will display:

Indicate Physical

Select Yes for a TPM device to be detected by the system at each system boot.
The options are Yes and No.

TPM Deactivated

Select Set to activate a TPM device at bootup. Select Clear to deactivate a TPM
device. The options are Set, Clear and Don't Change.

TPM Owner

Select Enable Install to set up a TPM ownership. Select Clear to void a TPM
ownership. Select Disable Install to disable TPM ownership setup support. The
options are Don't Change, Enable Install, Disable Install and Clear.

Execute TPM Command

Select Enabled to allow the user to change executable TPM commands and TPM
settings. Select Don't Change to keep the current TPM settings. The options are

Don't Change, Enabled, and Disabled.

TPM Enable/Disable Status

This item displays the status of TPM Enabled/Disabled state.

TPM Owner Status

This item displays the status of TPM Ownership.

4-20

Chapter 4: AMI BIOS

IPMI Confi guration

Intelligent Platform Management Interface (IPMI) is a used to monitor and manage
system health from a remote site. For more information, please visit Intel's website
at www.intel.com.

IPMI Firmware Revision

This item displays the current IPMI fi rmware revision.

Status of BMC

Baseboard Management Controller (BMC) manages the interface between system
management software and platform hardware. This section displays the BMC
status codes.

View BMC System Event Log

This feat ur e d i sp l ays t h e BMC Syst e m Event Lo g (SE L). It shows the total number
of entries of BMC System Events. To view an event, press the <+> and <-> keys
to select an event from the even log and display the information.

Total Number of Entries

•

SEL Entry Number•

SEL Record ID•

SEL Record Type•

Event Timestamp•

Generator ID•

Event Message Format Ver.•

Event Sensor Type•

Event Sensor Number,•

Event Dir Type•

Event Data.•

Clear BMC System Event Log

Select OK and press the <Enter> key to clear the BMC system log. Select Cancel
to keep the BMC System log. The options are OK and Cancel.

4-21

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

Caution: Any cleared information is unrecoverable. Make absolutely sure
that you no longer need any data stored in the log before clearing the
BMC Event Log.

Set LAN Confi guration

This feature allows the user to confi gure the IPMI LAN settings.

Channel Number

This feature allows the user to enter a channel number to be used for the IPMI LAN
connection. This is initially set to [01].

Channel Number Status

This feature indicates the status of the channel number selected above.

IP Address Source

This feature allows the user to select the source of the IP address for the system. If
Static is selected, the user will need to manually enter the IP address for the system.
If DHCP is selected, the BIOS will search for a DHCP (Dynamic Host Confi guration
Protocol) server in the network that the system is attached to, and request the next
available IP address. The options are DHCP and Static. If Static is selected, the
following items will be available for confi guration.

IP Address

This feature allows the user to enter the IP address for your system. This should
be in decimal and in dotted quad form (i.e., 192.168.10.253). The value of each
three-digit number separated by dots should not exceed 255.

Subnet Mask

This item shows which subnet this system belongs to. The value of each three-digit
number separated by dots should not exceed 255.

Gateway Address

This is the IP address of the gateway in the network that the system is connected
to. This is usually a router.

Mac Address

The BIOS will automatically enter your system's Mac address; however it may be
over-ridden. Mac addresses are 6 two-digit hexadecimal numbers (Base 16, 0 ~ 9,
A, B, C, D, E, F) separated by dots. (i.e., 00.30.48.D0.D4.60).

4-22

Chapter 4: AMI BIOS

BMC Watch Dog Timer Action

This feature allows the BMC to reset or power down the system if the operating
system hangs or crashes. The options are Disabled, Reset System, Power Down,
Power Cycle. If this feature is not set to Disabled, the following item will display.

BMC Watch Dog TimeOut [Min:Sec]

This feature sets a timed delay (in minutes or seconds) before a system powers
down or resets after an operating system failure is detected. The options are [5
Min], [1 Min], [30 Sec], and [10 Sec].

Event Log Confi guration

View Event Log

Use this option to view the System Event Log.

Mark all events as read
This option marks all events as read. The options are OK and Cancel.

Clear event log

This option clears the Event Log memory of all messages. The options are OK
and Cancel.

PCI Error Log
Use this option to enable PCI error (PERR) logging. The options are Yes and No.

Memory ECC Error Log

Use this option to enable ECC Memory Error logging. The options are Yes and
No.

4-23

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

4-4 Security Settings

The AMI BIOS provides a Supervisor and a User password. If you use both pass­words, the Supervisor password must be set fi rst.

Supervisor Password

This item indicates if a Supervisor password has been entered for the system. "Not
Installed" means a Supervisor password has not been used.

User Password

This item indicates if a user password has been entered for the system. "Not I n­stalle d" means that a u ser password has not been used.

Change Supervisor Password

Select this feature and press <Enter> to access the submenu, and then enter a
new Supervisor Password.

User Access Level (Available when Supervisor Password is set as above)

The Options are Full Access, View Only, Limited, and No Access

Full Access

• : This feature grants the user the full read and write access to the

Setup Utility.

View Only: This feature allows the user to access the Setup Utility without mak-

•

ing any change to the settings.

Limited: This feature allows the user to access limited fi elds and making

•

changes.

No Access: This feature prevents the user from accessing the Setup Utility.

•

4-24

Chapter 4: AMI BIOS

Change User Password

Select this feature and press <Enter> to access the submenu, and then enter a
new User Password.

Clear User Password (Available only when User Password has been set)

This item allows the user to clear a user password after it has been entered.

Password Check

Select Setup to allow the system to check for a user or supervisor password when­ever it enters into the BIOS Setup. Select Always to allow the system to check for
a user or supervisor password at each system boot. The options are Setup and
Always.

Boot Sector Virus Protection

When this item is enabled, the AMI BIOS displays a warning when any program
(or virus) issues a Disk Format command or attempts to write to the boot sector of
the hard disk drive. The options are Enabled and Disabled.

4-5 Boot Confi guration

Use this feature to confi gure boot settings.

Boot Device Priority

This feature allows the user to specify the sequence of priority for the Boot Device.
The settings are 1st boot device, 2nd boot device, 3rd boot device, 4th boot device,
5th boot device and Disabled.

4-25

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

Hard Disk Drives

This feature allows the user to specify the boot sequence from available Hard Disk
Drives. The settings are 1st boot device, 2nd boot device, and Disabled.

1st Drive - [SATA: XXXXXXX]/2nd Drive - [SATA: XXXXXXX]

Removable Drives

This feature allows the user to specify the boot sequence from available Removable
Drives. The settings are 1st boot device, 2nd boot device, and Disabled.

1st Drive - [USB: XXXXXXXXX]/2nd Drive

CD/DVD Drives

This feature allows the user to specify the boot sequence from available CD/DVD
Drives (i.e., 1st Drive, 2nd Drive, etc).

Retry Boot Devices

If this item is enabled, the BIOS will automatically attempt to boot from a speci­fi ed boot devic e ag ain af te r its i nit ial fa ilur e to bo ot. Th e opt ion s are Ena ble d and

Disabled.

4-6 Exit Options

Select the Exit tab from the AMI BIOS Setup Utility screen to enter the Exit BIOS
Setup screen.

4-26

Chapter 4: AMI BIOS

Save Changes and Exit

When you have completed the system confi guration changes, select this option
to leave the BIOS Setup Utility and reboot the computer, so the new system con­fi guration parameters can take effect. Select Save Changes and Exit from the Exit
menu and press <Enter>.

Discard Changes and Exit

Select this option to quit the BIOS Setup without making any permanent changes
to the system confi guration, and reboot the computer. Select Discard Changes and
Exit from the Exit menu and press <Enter>.

Discard Changes

Select this option and press <Enter> to discard all the changes and return to the
AMI BIOS Utility Program.

Load Optimal Defaults

To set this feature, select Load Optimal Defaults from the Exit menu and press
<Enter>. Then, select OK to allow the AMI BIOS to automatically load Optimal De­faults to the BIOS Settings. The Optimal settings are designed for maximum system
performance, but may not work best for all computer applications.

Load Fail-Safe Defaults

To set this feature, select Load Fail-Safe Defaults from the Exit menu and press
<Enter>. The Fail-Safe settings are designed for maximum system stability, but not
for maximum performance.

4-27

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

Notes

4-28

Appendix A: BIOS POST Error Codes

Appendix A

BIOS Error Beep Codes

During the POST (Power-On Self-Test) routines, which are performed whenever
the system is powered on, errors may occur.

Non-fatal errors are those which, in most cases, allow the system to continue
with the boot-up process. The error messages normally appear on the screen.

Fatal errors are those which will not allow the system to continue with bootup. If
a fatal error occurs, you should consult with your system manufacturer for pos­sible repairs.

These fatal errors are usually communicated through a series of audible beeps.

BIOS Error Beep Codes

Beep Code Error Message Description

1 beep Refresh Circuits have been reset.

(Ready to power up)

5 short beeps, 1 long
beep

8 beeps Display memory

1 continuous beep w/
Front Panel OH LED on

Memory error No memory detected in the

system
Video adapter missing or with

read/write error
System Overheat 1 continuous beep with the

faulty memory

front panel OH LED on

A-1

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

Notes

A-2

Appendix B: Software Installation Instructions

Appendix B

Software Installation Instructions

B-1 Installing Software Programs

After you've installed the Windows Operating System, a screen as shown below will
appear. You are ready to install software programs and drivers that have not yet
been installed. To install these software programs and drivers, click the icons to the
right of these items. (To install the Windows OS, please refer to the Windows OS
Installation Guide posted at http://www.supermicro.com/support/manuals/.)

Note 1. Click the icons showing a hand writing on the paper to view the
readme fi les for each item. Click on a computer icon to the right of an item
to install an item (from top to the bottom) one at a time. After installing
each item, you must re-boot the system before proceeding with the next
item on the list. The bottom icon with a CD on it allows you to view the
entire contents of the CD.

Note 2. When making a storage driver diskette from booting into a Driver
CD, please set the SA T A Confi guration to "Compatible Mode" and confi gure
SATA as IDE in the BIOS Setup. After making the driver diskette, be sure
to change the SATA settings back to your original settings.

Driver/Tool Installation Display Screen

B-1

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

B-2 Confi guring Supero Doctor III

The Supero Doctor III program is a Web-based management tool that supports
remote management capability. It includes Remote and Local Management tools.
The local management is called the SD III Client. The Supero Doctor III program
included on the CDROM that came with your motherboard allows you to monitor
the environment and operations of your system. Supero Doctor III displays crucial
system information such as CPU temperature, system voltages and fan status. See
the Figure below for a display of the Supero Doctor III interface.

Note: 1 The default user name and password are ADMIN.
Note 2: In the Windows OS environment, the Supero Doctor III settings

take precedence over the BIOS settings. When fi rst installed, Supero Doc-
tor III adopts the temperature threshold settings previously set in BIOS. Any
subsequent changes to these thresholds must be made within Supero Doc­tor, since the SD III settings override the BIOS settings. For the Windows
OS to adopt the BIOS temperature threshold settings, please change the
SDIII settings to be the same as those set in BIOS.

Supero Doctor III Interface Display Screen-I (Health Information)

B-2

Appendix B: Software Installation Instructions

Supero Doctor III Interface Display Screen-II (Remote Control)

Note: SD III Sof tware Revisio n 1. 0 can be downloa ded from our Web -

site at: f tp://ft p.superm icro.co m/utilit y/Supero _D octor_I II/. You c an also
download SDIII User's Guide at: http://www.supermicro.com/PRODUCT/
Manuals/SDIII/UserGuide.pdf. For Linux, we will still recommend that you
use Supero Doctor II.

B-3

X8DTH-6/X8DTH-6F/X8DTH-i/X8DTH-iF User's Manual

Notes

B-4

The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices,
aircraft/emergency communication devices or other critical systems whose failure to perform be reasonably expected to result in signifi cant injury or loss of life or catastrophic
property damage. Accordingly, Supermicro disclaims any and all liability, and should buyer use or sell such products for use in such ultra-hazardous applications, it does so
entirely at its own risk. Furthermore, buyer agrees to fully indemnify, defend and hold Supermicro harmless for and against any and all claims, demands, actions, litigation, and
proceedings of any kind arising out of or related to such ultra-hazardous use or sale.

(Disclaimer Continued)